Page 1
RC200
Remote Control Speakerphone
Operating Instructions
Please read these instructions carefully before use. Keep for future reference.
Clarity,a Division of Plantronics, Inc.
520001
PM120204 ENG/FRE Rev B
Page 2
Wall Mount Option
1. Use mounting screws or other
hardware to secure the RC to
the wall at the desired location.
2. Two mounting holes are located
on the bottom of the RC unit.
Measure the distance between
the holes and then mark two
points on your wall that match
the distance between the
mounting holes on your RC.
3. Place a mounting screw (not
provided) at the location marked
on your wall in the previous
step. Be sure to use appropriate
mounting hardware and
supplies.
4. Align the screws with the holes
in your RC unit and affix the RC
unit firmly to your wall.
Page 3
Important Safety Instructions
When using your telephone equipment, basic safety precautions should
always be followed to reduce the risk
of fire, electric shock and persons
including the following:
1. Read and understand all
instructions.
2. Follow all warnings and instruc-
tions marked on the telephone.
3. Do not use this telephone near a
bathtub, wash basin, kitchen sink
or laundry tub, in a wet basement,
near a swimming pool or any
where else there is water.
4. Avoid using a telephone (other
than a cordless type) during a
storm. There may be a remote
risk of electrical shock from
lightning.
5. Do not use the telephone to
report a gas leak in the vicinity
of the leak.
6. Unplug this telephone from the
wall outlets before cleaning. Do
not use liquid cleaners or aerosol
cleaners on the telephone. Use a
damp cloth for cleaning.
7. Place this telephone on a stable
surface. Serious damage and/or
injury may result if the telephone
falls.
8. Do not cover the slots and open
ings on this telephone. This tele
phone should never be placed
near or over a radiator or heat
register. This telephone should
not be placed in a built-in installation unless proper ventilation is
provided.
9. Operate this telephone using the
electrical voltage as stated on the
base unit or the owner’s manual.
If you are not sure of the voltage
in your home, consult your dealer
or local power company.
10. Do not place anything on the
power cord. Install the telephone
where no one will step or trip on
the cord.
11. Do not overload wall outlets or
extension cords as this can
increase the risk of fire or
electrical shock.
12. Never push any objects through
the slots in the telephone. They
can touch dangerous voltage
Page 4
Important Safety Instructions
points or short out parts that
could result in a risk of fire or
electrical shock. Never spill liquid
of any kind on the telephone.
13. To reduce the risk of electrical
shock, do not take this phone
apart. Opening or removing covers may expose you to dangerous
voltages or other risks. Incorrect
reassembly can cause electric
shock when the appliance is
subsequently used.
14. Unplug this product from the wall
outlets and refer servicing to the
manufacturer under the following
conditions:
A. When the power supply cord
or plug is frayed or damaged.
B. If liquid has been spilled into
the product.
C. If the telephone has been
exposed to rain or water.
D. If the telephone does not
operate normally by following
the operating instructions.
Adjust only those controls
that are covered by the oper
ating instructions. Improper
adjustment may require exten
sive work by a qualified tech
nician to restore the tele
phone to normal operation.
E. If the telephone has been
dropped or the case has been
damaged.
F. If the telephone exhibits a
distinct change in performance.
15. Never install telephone wiring
during a lightning storm.
16. Never install telephone jacks in
wet locations unless the jack is
specifically designed for wet
locations.
17. Never touch uninsulated tele
phone wire s or terminals unless
the telephone line has been dis
connected at the network
interface.
18. Use caution when installing or
modifying telephone lines.
19. Use only the power cord and
batteries indicated in this manual.
Do not dispose of batteries in a
fire. They may explode. Check
with local codes for possible
special disposal instructions.
SAVE THESE INSTRUCTIONS
Page 5
ADDITIONAL SAFETY NOTES
FOR CANADIAN USERS
The following items are included as
part of the CS-03 Requirements.The
standard connecting arrangement for
the equipment is CA11A. This product meets the applicable Industry
Canada technical specifications.
NOTICE: The Canadian Department
of Communications label identifies
certified equipment.This certification
means that the equipment meets certain telecommunications network protective operational and safety requirements.The Department does not
guarantee that the equipment will
operate to the user’s satisfaction.
Before installing this equipment, users
should ensure that it is permissible to
be connected to the facilities of the
local telecommunications company.
The equipment must also be installed
using an acceptable method of connection. In some cases, the company’s
inside wiring associated with a single
line individual service may be extended by means of a certified connector
assembly (telephone extension cord).
The customer should be aware that
compliance with the above conditions
may not prevent degradation of service in some situations. Repairs to certified equipment should be made by an
authorized Canadian maintenance
facility designated by the supplier. Any
repairs or alterations made by the
user to this equipment, or equipment
malfunctions, may give the telecommunications company cause to request
the user disconnect the equipment.
Users should ensure for their own
protection that the electrical ground
connections of the power utility, telephone lines and internal metallic water
pipe system, if present, are connected
together.This precaution may be particularly important in rural areas.
CAUTION: Users should not
attempt to make such connections
themselves, but should contact the
appropriate electric inspection authority, or electrician, as appropriate. The
Ringer Equivalent Number is an indication of the maximum number of terminals allowed to be connected to a
telephone interface. The termination
on an interface may consist of any
combination of devices subject only to
the requirement that the sum of the
Ringer Equivalent Number of all the
devices not exceed five.
SAVE THESE INSTRUCTIONS
Page 6
TABLE OF CONTENTS
CHAPTER 1. INTRODUCTION....................................................................................................................2
CHAPTER 2. PACKAGE CHECKLIST........................................................................................................2
CHAPTER 3. FEATURES IDENTIFICATION ........................................................................................3
CHAPTER 4. INSTALLATION........................................................................................................................4
A. Batteries..................................................................................................................................4
B. Connections ..........................................................................................................................4
C. Setting Up Your RC..............................................................................................................4
CHAPTER 5. OPERATION ..............................................................................................................................6
A. Programming Numbers Into Memory ............................................................................6
B. Making Phone Calls ..............................................................................................................6
1. Dialing on the keypad..........................................................................................6
2. Memory dialing from console............................................................................6
3. Auto dialing the first number stored in M1 ..................................................7
4. Dialing using the Scan button............................................................................7
5. Dialing using the Remote Transmitter ............................................................7
C.Answering Phone Calls........................................................................................................7
1. Using the keypad ..................................................................................................7
2. Using the Remote Transmitter ..........................................................................7
3. Voice activated answering ..................................................................................8
D. Other Operations ................................................................................................................8
1. Redialing..................................................................................................................8
2. Flash ........................................................................................................................8
3. Voice mail indicator..............................................................................................8
4. Unanswered call indicator..................................................................................8
5. Telebanking and credit card calling ..................................................................8
CHAPTER 6. OPTIONAL ACCESSORIES ..............................................................................................9
A.Air Switch™ ..........................................................................................................................9
B. Pillow Switch ..........................................................................................................................9
C. Lapel Microphone ................................................................................................................9
D. Headset ..................................................................................................................................9
QUICK START GUIDE/SUMMARY ..........................................................................................................10
CHAPTER 7. IN CASE OF DIFFICULTY................................................................................................12
CHAPTER 8. MAINTENANCE....................................................................................................................14
CHAPTER 9. FCC INFORMATION ..........................................................................................................14
CHAPTER 10.WARRANTY ..........................................................................................................................18
CHAPTER 11. FEATURE SUMMARY ......................................................................................................19
CONTACT US ......................................................................................................................................................19
INDEX ......................................................................................................................................................................19
Page 7
CHAPTER 1
DIAL
OGU
E
RC
TM
123
6
5
4
78
0
*
9
#
Remote Transmitter
and Battery
Batteries (RC-200 only)
AC adapter/battery charger
Operating Instructions
Phone Cords
DIALOGUE
RC
Necklace (for
hanging the
remote control)
Velcro strip (for
remote control
attachment)
INTRODUCTION
CHAPTER 2
PACKAGE CHECKLIST
Thank you for selecting the exciting
new RC Remote Control Speakerphone from
CLARITY, Inc. It has been designed to meet
the highest quality standards in order to
provide you with years of convenient and
trouble–free service.
Please read these operating instructions thoroughly before using the
RC. Or, to begin using
the RC as quickly as possible, see Chapter 5
"Quick Start Guide/Summary". Keep this manual for future reference.
You must save your sales receipt as proof of
purchase in the event that you need warranty
service.
If you have any questions about your
RC, please call our Customer Service
Department at:
Voice: (800) 426-3738
TTY: (800)772-2889
Fax: (800) 325-8871
Your RC package includes the items as shown
below:
2
Figure 1 – DIALOGUE
Components.
RC
Page 8
M1
M2
M3
M4
M5
M6
M7
M8
M9
M10
DIALOGUE
RC
VOL
PROG SCAN
MUTE
POWER
FLASH/PAUSE
REDIAL
ON/OFF
HEADSET
MIC
TM
PHONE
LINE
OFF LO HI
RINGER
AC
ADAPTER
AIR SWITCH
123
6
5
4
78
0
*
9
#
A
B
C
D
E
F
M
N
O
J
K
L
G
H
I
P
R
S
T
U
V
O
P
R
W
X
Y
CHAPTER 3
FEATURES IDENTIFICATION
Jack for Air Switch or accessory
switch
AC adapter plug
Phone line jack
Ringer volume control
Lapel Microphone jack
Headset port (Operational in
RC200 only)
Memory location indicators
Memory directory
Memory buttons
Power indicator
Speaker
Battery compartment
(underneath)
Tone/pulse selector (underneath)
Remote Flash on/off switch, underneath (Operational in RC200 only,)
Figure 2 – Features Identification
Headset on/off button
(Operational in RC200 only)
Mute button
Flash/Pause button
On/Off button
Redial button
Voice Mail/Unanswered Call
Indicator
Microphone
Scan button
Volume control
Memory Program button
3
Page 9
BATTERYBATTERY
CHAPTER 4
INSTALLATION
A. Battery (included with RC200) B. Connections
Speakerphone
1. Six "AA" size,
Nickel Metal Hydride
(Ni-MH) rechargeable batteries are
used for back–up
during a power outage (Fig 3).They
power the RC
for approximately
5 hours. DO NOT
Figure 3 – battery
compartment
USE ALKALINE
BATTERIES, they will damage your
equipment.
Remote Transmitter
2. Install the "23A" size 12V alkaline cigarette
lighter battery in the Remote Transmitter
(included) as shown (Fig 4).With normal
usage, it lasts 6–12 months. If the power
indicator light is faint or does not come on
when the button is pressed, replace the
battery.The Remote Transmitter has an
operating range of up to 40 feet.
Power
indicator
Jack for
accessory
switch
Thread both
Battery
compartment
Figure 4 – Remote Transmitter
ends of necklace
through hole and
tie a small knot.
(optional)
Figure 5 – Connection of phone line and
1. Connect the phone line and AC adapter
as shown.
2. Set the tone/pulse selector (T/P) to T if
you have touch tone service, set to P if
you have pulse dialing (rotary). (See Fig 2)
The RC can be placed on a desk, or mounted
on the wall. Do not put the RC on or next to
metal surfaces, computers, televisions, radios,
microwaves, or other electrical equipment that
can cause interference to the wireless signal
from the Remote Transmitter.
C. Setting up your RC
The RC comes with the following
operating settings from the factory:
1. Scan rate is 5 seconds per memory
location.
2. Voice activated answering (RC200
only) is off.
3. Unanswered call indicator is on.
4. Voice mail indicator (RC200 only) is
off.
5. Tone/pulse switch set to Tone.
6. Ring volume set to Hi.
7. "0" (operator) is programmed into first
memory location of M1.
8. Remote flash switch (RC200 only) is off.
AC adapter
4
Page 10
CHAPTER 4
VOL
PROG
SCAN
MUTE
HEADSET
MIC
Key Entered
Length of Pause at Each
Location in Seconds
Scan Function Off
5
4.5
4
3.5
3
2.5
2
1.5
1
VOL
PROG
SCAN
MUTE
HEADSET
MIC
(CONTINUED)
You may set up the RC in the following manner
to better suit your needs.
Setting the Scan Function
If you have RC100:
Only the first six numbers in the memory are
automatically scanned. It stops at each memory
location for 5 seconds to allow you to select.
To turn scan function off (or on):
1. Press PROGRAM.
2. Press 0 on the keypad to turn it off;
or press 1 key on the keypad to turn it on.
3. Press SCAN button.
If you have RC200:
All memory locations with numbers stored are
automatically scanned. The scan rate determines how long the RC200 pauses at each
memory location before moving on to the next
one.
To turn scan function on or off:
1. Press PROGRAM.
3. Press SCAN button.
Figure 8
To turn Voice Activation on (or off)
(RC200 only):
1. Press PROGRAM.
2. Press MUTE button twice.The MUTE
indicator flashes once, and the RC200
emits four beeps to confirm that
Voice Activation has been turned on.
3. To turn it off, repeat steps 1 and 2.
This command is confirmed by four beeps.
To turn the Unanswered Call Indicator
(RC200) feature off (or on):
1. Press PROGRAM.
2. Press HEADSET button twice.
(Emits four beeps to confirm command).
3. To turn it on again, repeat steps 1
and 2, and the HEADSET indicator
flashes once.
Figure 6
2. Using chart, select length of pause and press
the corresponding digit on keypad.
Figure 7
To turn the Voice Mail Indicator feature
on (or off), (RC200 only):
1. Press PROGRAM.
2. Press FLASH/PAUSE button twice.
RC200 emits four beeps and the
FLASH/PAUSE indicator flashes once.
3. To turn it off again, repeat steps 1
and 2, and the FLASH/PAUSE
indicator does not flash.
To turn the Remote Flash feature on (or
off) (RC200 only):
1. Slide remote flash switch to "On"
(or "Off") position.
5
Page 11
a
VOL
PROG
SCAN
MUTE
HEADSET
MIC
M9
M10
VOL
FLASH/PAUSE
REDIAL
MUTE
ON/OFF
HEADSET
MIC
FLASH/PAUSE
REDIAL
MUTE
ON/OFF
HEADSET
MIC
M8
M9
M10
VOL
PROG SCAN
FLASH/PAUSE
REDIAL
MUTE
ON/OFF
HEADSET
MIC
FLASH/PAUSE
REDIAL
MUTE
ON/OFF
HEADSET
MIC
M9
M10
VOL
FLASH/PAUSE
REDIAL
MUTE
ON/OFF
HEADSET
MIC
CHAPTER 5
OPERATION
For optimum communication clarity, speak
into the RC as close as possible, not to
exceed 15 feet away. Keep the microphone
free from obstructions. Do not speak at the
same time as the other person.Also, adjust
the volume control and set the ring volume to
best suit your hearing needs.
A. Programming numbers into memory
Your RC can store up to 20 numbers (two
numbers per button) in its memory for fast,
one–touch dialing.When programming, pressing
FLASH/PAUSE button between numbers
the
inserts a 2 second pause in dialing.
To program a number into memory:
Press PROGRAM.
1.
Figure 9
2. Dial the number (up to 40 digits).
Figure 10
3. Select the memory button to store this
number, press once for first location,
or twice for second location.When the
number is programmed, it emits four
"beeps" to confirm the number is stored.
4. If you make a mistake or want to
change the number, repeat from step
To erase a number, press PROGRAM,
5.
then FLASH/PAUSE, and then the
corresponding memory location.
6
B. Making phone calls
Dialing on the keypad
Press ON/OFF button
1.
and listen for dial tone.
Figure 11
2. Dial the number on the
keypad.(If no number
is dialed within 7
seconds,
RC automatically
DIALOGUE
Figure 12
dials the first number
stored in memory
location
M1.)
3. When finished, press the ON/OFF
button to hang up.
Memory dialing from console
1. For the first number
stored in each memory
button, press the
memory button once.
For the second number,
Figure 13
press the memory button twice.The
indicator light on the directory shows
the memory selected.
2. The number is dialed after a 3 second
wait, allowing you time to change your
selection.
1.
3. When finished,
press the
ON/OFF
button to hang up.
Figure 14
Page 12
CHAPTER 5
FLASH/PAUSE
REDIAL
MUTE
ON/OFF
HEADSET
MIC
FLASH/PAUSE
REDIAL
MUTE
ON/OFF
HEADSET
MIC
VOL
PROG
SCAN
MUTE
HEADSET
MIC
(CONTINUED)
Auto Dialing the first number stored in
M1.
A. From keypad
1. Press ON/OFF button or just press M1.
2. The number is dialed automatically
within 7 seconds.
B. Using Remote Transmitter With Scan
function on:
1. Press Remote Transmitter.
2. The number is dialed automatically
after scanning all memories 3 times.
C. With Scan function off:
1. Press Remote Transmitter.
2. The number is dialed automatically.
Dialing by using the SCAN button
Before you can use memory scanning for dialing, you must have the phone numbers stored
in the memory first (page 6). To use memory
scanning, the Scan function must be on. See
Chapter 4 section C. Memory locations with
no number stored are skipped. The memory
directory is scanned three times or until a number is selected. If no number is selected, the first
number in M1 is dialed.
1. Press the SCAN
button.
Figure 15
2. The memory location indicators light
up as it scrolls down the memory
locations. If you have RC100: Only the
first six memory locations are scanned. If
you have RC200:All 20 memory loca-
tions are scanned (It "beeps" when
advancing to the next memory location.)
3. When the desired memory location is lit,
4. The RC automatically
dials the number
selected.
5. Press the ON/OFF
Figure 16
button to hang up.
Dialing using the Remote Transmitter
A. With Scan function on:
1. Press the Remote
Transmitter to
begin scanning.
2. When the desired
Figure 17
memory location is lit, press the
Remote Transmitter.The RC auto
matically dials the number selected.
3. Press the Remote Transmitter once
to hang up.
B. With Scan function off:
1. Press the Remote Transmitter once.
2. It dials the first number stored in M1.
C. Answering phone calls
Using the keypad
1. When the phone rings,
press the ON/OFF
button to turn it on.
2. When finished, press
Figure 18
the ON/OFF button to
hang up.
Using the Remote Transmitter
1. When the phone rings,
press the Remote
Transmitter to turn on.
2. Press the remote
Figure 19
button once to hang up.
7
Page 13
CHAPTER 5
FLASH/PAUSE
REDIAL
MUTE
ON/OFF
HEADSET
MIC
FLASH/PAUSE
REDIAL
ON/OFF
REDIAL
ON/OFF
FLASH/PAUSE
REDIAL
ON/OFF
FLASH/PAUSE
(CONTINUED)
Voice Activated answering
(RC200 only)
1. The voice activated Answering feature
has been preset to OFF in the factory.
To activate this feature, see page 5.
2. Say "Hello" or whistle loudly, between
rings. (If a headset is used, answer by
speaking into the headset microphone.)
3. Use the remote control, or press the
ON/OFF button on the console to hang up.
Please Note:When the party that called
you hangs up, the telephone company
switching office may re-establish a dial
tone on your line.
When dial tone returns, your RC200
will hang up automatically. Prior to
hanging up, the RC200 emits two short
beeps as a reminder.
D. Other Operations
Redialing the last number dialed
1. Press the REDIAL
button on the keypad.
OR
2. Press and hold the
Remote Transmitter for
3 seconds, until the
ON/OFF indicator on
DIALOGUE RC
turns on.
Flash button
The flash button is used to access special telephone functions and services available from
your local phone company, such as call waiting,
3–way calling, and others. Call your phone
company for more information.
8
Figure 20
Figure 21
If you have the RC200, you can use the Flash
feature with the Remote Transmit--ter.Turn
the Remote Flash switch on (see Chapter 4 section C).When you are on the phone line, press
the Remote Transmitter button twice in succession, within three seconds, to generate the
“flash”.
Voice Mail Indicator (VMI)
If you subscribe to voice mail service from
your phone company, the FLASH/PAUSE light
flashes and the RC beeps (once every 3.5 minutes) to inform you that you have voice mail
messages.You also hear a special "stutter" dial
tone sent from the phone
company.To retrieve your messages,follow the instructions
provided by your phone
company. Making an
outgoing call cancels the
Figure 22
indicator light.
Unanswered Call
Indicator
If the RC rings three or more
times and is not answered,
the FLASH/PAUSE light
Figure 23
flashes to indicate that you missed
a call.Turning on the RC cancels the indicator.
Telebanking and Credit Card Calling
You can transmit account or personal
identification numbers (PIN) from the
RC by pre–storing them in memory.
1. Program account or PIN numbers into
a memory location in advance by
following the same steps you would
program a phone number.
2. When the automated phone system
requests it, press the memory button
where your account number or PIN is
stored.
Page 14
CHAPTER 6
OPTIONAL ACCESSORIES
A. AIR SWITCH™
This Accessory
switch allows you
to place and answer
calls and control
every function of
the RC by blowing
gently on its air
sensor. It snaps on
to either the rear
of the console or
the remote control
for the ultimate in
“no-touch” accessory and control.
B. PILLOW SWITCH
Plugs into the
console or the
remote control
for your convenience.Allows
you to control
phone functions
by gently touching
it with your arm,
leg, head, shoulder or other
body movement.
A 6 foot long
cord connects it
easily.
C. LAPEL MICROPHONE
This highly sensitive microphone, clips to
your collar and
provides handsfree, crystal
clear, high fidelity sound for people who have weak voices. It has a cord that is 5 feet long.
D. HEADSET WITH MICROPHONE
Ensure the utmost privacy for personal
conversations or confidential business
calls.This light weight unit plugs into the
telephone with a 61/2 foot long cord and
is comfortable to wear, even for extended
periods of time.
For more information, please call or write:
Clarity Product Customer Service
4289 Bonny Oaks Drive
Chattanooga,TN 37406
(800) 426-3738 VOICE
(800) 772-2889 TTY
(800) 325-8871 FAX
www.clarityproducts.com
9
Page 15
QUICK START GUIDE/
1
1
1
1
1
111
1
1
1
1
1
1
SUMMARY
For more detailed description see Chapter 5.
OPERATION STEPS
FACTORY PRESET MODES OF OPERATION:
Scan rate = 5 seconds per memory
•
location.
Tone/pulse switch set to Tone.
•
TO CHANGE MODES OF OPERATION
Setting the Scan Function
If you have RC100 Press PROGRAM.
To turn Scan function off (or on):
If you have
To turn Scan function off (or on):
To turn Voice Activation on (or off), Press PROGRAM.
(RC200 only):
To turn the Unanswered Call Press PROGRAM.
Indicator feature off (or on):
To turn the Voice Mail Indicator Press PROGRAM.
feature on (on off), (RC200 only):
PROGRAMMING NUMBERS INTO MEMORY
MAKING A CALL BY DIALING ON THE RC
A. From the keypad Press ON/OFF button.
B.Auto Dialing the first number stored in M1 Press ON/OFF button.
C. Memory Dialing Press a memory button once to dial the first
stored number, twice for the second number.
MAKING A CALL USING THE REMOTE TRANSMITTER
A.With Scan function on Press Remote Transmitter once.
B.With Scan function off Press Remote Transmitter once.
ANSWERING A CALL
A. From the keypad Press ON/OFF button to answer.
B. Using the Remote Transmitter Press Remote Transmitter once to answer.
C. Using Voice Activation, Say “Hello” or whistle between rings
(RC200 only). to turn on phone.
RC200 Press PROGRAM.
Press PROGRAM.
10
Page 16
Voice Activated answering Unanswered call indicator is Voice Mail indicator is off,
2
2
2
2
2
2
2
3
333
3
3
2
2
2
2
2
2
•
is off, (RC200 only). on. (RC200).
Ring volume set to Hi. ”0“ (operator) is programmed into Remote Flash switch is off,
•
Press
0 on the keypad to Press SCAN button.
turn it off; or Press 1 key on
the keypad to turn it on.
Press 0 key to turn it off;or Press SCAN button.
Press 1-9 keys to turn it on. See
Page 5 for rate selection guide.
Press MUTE twice.
Press HEADSET twice.
Press FLASH/PAUSE twice.
Dial the number (up to Select the memory button. Press once for first location, or
40 digits). twice for second location.
•
•
the first memory location of M1. (RC200 only).
•
•
Dial the number. Press
The number is dialed in
7 seconds.
When the desired directory Press Remote Transmitter to hang up.
location is lit, press it again.
The first number stored Press Remote Transmitter once to
under M1 is dialed. hang up.
Press ON/OFF button to hang up.
Press Remote Transmitter once to hang up.
It hangs up automatically after one minute of silence or when it detects dial tone.
ON/OFF button to hang up.
11
Page 17
CHAPTER 7
IN CASE OF DIFFICULTY
If any problem should occur during operation of your RC, review the list below.
Should the difficulty persist, contact AMERIPHONE or your authorized dealer before sending
the phone for service.
SYMPTOM
No dial tone
No power
Does not dial out
Does not dial memory number
Remote Transmitter does not work
No audible ring
Does not scan through memory
Scanning too fast/slow
Cuts in and out while speaking/
listening
CAUSE AND REMEDY
– Check all phone line connections.
– Check power connection.
– Check all phone line connections and power
connection.
– Change to pulse dialing and try again.
– No number programmed in memory.
– Check or replace battery.
– Check channel settings.
– Make sure no part of the RC
system is on or near metal surfaces or electrical
equipment.
– Make sure the ringer is not set to "Off" position.
– Turn on Scan function.
– Program Scan rate to a slower/faster setting.
(Dialogue RC200 only.)
– Avoid speaking at the same time as the other
party. Take turns.
SENSITIVITY ADJUSTMENT
YOU MUST CONTACT AMERIPHONE BEFORE MAKING THE FOLLOWING ADJUSTMENT:
Callers can’t hear your voice when
using the optional headset with integrated microphone
12
HEADSET MIC GAIN adjustment, located
– Turn
on bottom of unit, clockwise to increase
sensitivity, counterclockwise to decrease.
Page 18
CHAPTER 7
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
S
E
T
T
O
M
A
T
C
H
E
X
A
C
T
L
Y
(CONTINUED)
CHANNEL SETTINGS
The RC and Remote Transmitter use radio
signals to communicate with each other. For
the Remote Transmitter to activate the
they both have to be on the same "channel."
A "DIP Switch" is used for channel selection.
Your phone and remote have been preset at
the factory to a standard channel setting.
Under normal operating conditions, there is
no adjustment necessary.
If your system encounters interference and
repeatedly activates by itself for no obvious
reasons, it may be necessary to change DIP
Switch settings on the
RC and Remote
Transmitter.
RC,
(Remove cover to
expose switch)
1. Unscrew bottom of the Remote
Transmitter.
2. Locate DIP Switches on Remote
Transmitter and on bottom of
RC.
3. Using a ball point pen, change the
settings on all switch positions to
match exactly on both RC
and Remote Transmitter.
4. Replace remote cover and test.
Figure 24 – Channel setup
13
Page 19
CHAPTER 8
MAINTENANCE
CHAPTER 9
REGULATORY INFORMATION
To ensure trouble–free service, your
RC should always be treated with care. Do
not drop or subject the phone to high impact.
The unit can be cleaned with a damp cloth
and a mild detergent. Never use abrasives or
solvents.
Keep the unit plugged into the electrical outlet
at all times, except when cleaning.This will
automatically recharge the optional back–up
batteries, and keep the phone operational for
incoming calls.We recommend using a surge
protector to prevent damage to the
case of power surges or electrical storms.
RC in
Part 68 of FCC Rules Information
This RC100 or RC200 Remote Controlled
Speakerphone complies with Part 68 of the
FCC rules and the requirements adopted by
the ACTA.
On the bottom of this equipment is a label
that contains, among other information, a
product identifier in the format
US:AAAEQ##TXXXX. If requested, this number must be provided to the telephone company.
A plug and jack used to connect this equipment to the premises wiring and telephone
network must comply with the applicable FCC
Part 68 rules and requirements adopted by
the ACTA.A compliant telephone cord and
modular plug, RJ11 USOC, is provided with
this product. It is designed to be connected to
a compatible modular jack that is also compliant. See installation instructions for details.
The REN is used to determine the number of
devices that may be connected to a telephone
line. Excessive RENs on a telephone line may
result in the devices not ringing in response to
an incoming call. In most but not all areas, the
sum of RENs should not exceed five (
be certain of the number of devices that may
be connected to a line, as determined by the
total RENs, contact the local telephone company. For products approved after July 23,
2001, the REN for this product is part of the
product identifier that has the format
US:AAAEQ##TXXXX .The digits represented
by ## are the REN without a decimal point
(e.g., 03 is a REN of 0.3). For earlier products,
the REN is separately shown on the label.
5.0).To
14
Page 20
If this telephone equipment causes harm to
the telephone network, the telephone company will notify you in advance that temporary
discontinuance of service may be required. But
if advance notice isn’t practical, the telephone
company will notify the customer as soon as
possible.Also, you will be advised of your right
to file a complaint with the FCC if you believe
it is necessary.
The telephone company may make changes in
its facilities, equipment, operations or procedures that could affect the operation of the
equipment. If this happens the telephone company will provide advance notice in order for
you to make necessary modifications to maintain uninterrupted service.
If trouble is experienced with this telephone
equipment, for repair or warranty information,
please contact Clarity, 1-800-426-3738. If the
equipment is causing harm to the telephone
network, the telephone company may request
that you disconnect the equipment until the
problem is resolved.
This telephone equipment is not intended to
be repaired and it contains no repairable
parts. Opening the equipment or any attempt
to perform repairs will void the warranty. For
service or repairs, call 1-800-426-3738
Connection to party line service is subject to
state tariffs. Contact the state public
utility commission, public service commission
or corporation commission for information.
If your home has specially wired alarm equipment connected to the telephone line, ensure
the installation of this telephone equipment
does not disable your alarm equipment. If you
have questions about what will disable alarm
equipment, consult your telephone company
or a qualified installer.
This telephone equipment is hearing aid
compatible.
We recommend the installation of an AC
surge arrester in the AC outlet to which this
equipment is connected. The telephone companies report that electrical surges, typically
lighting transients, are very destructive to customer terminal equipment connected to AC
power sources
Customer-Owned Coin/Credit Card
Phones:
To comply with state tariffs, the telephone
company must be given notification prior to
connection. In some states, the state public
utility commission, public service commission
or corporation commission must give prior
approval of connection.
Part 15 of FCC Rules Information
This device complies with part 15 of the FCC
Rules. Operation is subject to the following
two conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired operation.
Your telephone equipment has been tested
and found to comply with the limits of a Class
B digital device, pursuant to Part 15 of FCC
rules. These limits are designed to provide
reasonable protection against harmful interference in residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular
installation; if this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, you are encouraged to
try to correct the interference by one of the
following measures:
15
Page 21
Where it can be done safely, reorient the
receiving television or radio antenna.
To the extent possible, relocate the television,
radio or other receiver with respect to the
telephone equipment. (This increases the
separation between the telephone equipment
and the receiver.) Connect the telephone
equipment into an outlet on a circuit difference from that to which the television, radio,
or other receiver is connected. Consult the
dealer or an experienced radio/TV technician
for help.
CAUTION: Changes or modifications not
expressly approved by the manufacturer could
void the user’s authority to operate the equipment.
THE PARTY RESPONSIBLE FOR
PRODUCT COMPLIANCE:
Clarity,A Division of Plantronics, Inc.
4289 Bonny Oaks
Chattanooga,TN 37406, USA
Phone: (800) 426-3738,
Fax: (800) 325-8871
Industry Canada Technical
Specifications
This product meets the applicable
Industry Canada technical specifications.
Before installing this equipment, users should
ensure that it is permissible to be connected
to the facilities of the local telecommunications company. The equipment must also be
installed using an acceptable method of connection. In some cases, the company’s inside
wiring associated with a single line individual
service may be extended by means of a certified connector assembly (telephone extension
cord). The customer should be aware that
compliance with the above conditions may not
prevent degradation of service in some situations.
Repairs to certified equipment should be
made by an authorized Canadian maintenance
facility designated by the supplier. Any repairs
or alterations made by the user to this equipment, or equipment malfunctions, may give the
telecommunications company cause to
request the user to disconnect the equipment.
Users should ensure for their own protection
that the electrical ground connections of the
power utility, telephone lines and internal
metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas.
Caution:
such connections themselves, but should contact the appropriate electric inspection
authority, or electrician, as appropriate.
The Ringer Equivalence Number is an
indication of the maximum number of
terminals allowed to be connected to a
telephone interface.The termination on
an interface may consist of any combination of devices subject only to the
requirement that the sum of the Ringer
Equivalence Numbers of all the devices
does not exceed five.
[The term “IC:” before the certification/registration number only signifies that the Industry
Canada technical specifications were met.]
Users should not attempt to make
16
Page 22
17
Page 23
CHAPTER 10
WARRANTY
This warranty applies only to AMERIPHONE
products that are purchased and used in the
United States or Canada.
CLARITY, Inc. warrants the RC100 and
RC200 against any defect in materials or
workmanship for the period of one year from
the date of purchase.
If your AMERIPHONE product is defective and
returned within 30 days of the date of purchase, your authorized AMERIPHONE dealer
will replace it at no charge.
If returned after 30 days but within one year
from the date of purchase, we will repair or
replace it at no charge. In the repair of your
RC, we may use new or reconditioned
replacement parts. If we elect to replace your
RC, we may replace it with a new or reconditioned product of the same or similar design.
Repair or replacement will be warranted for
either 90 days or the remaining time on the
original warranty period, whichever is longer.
Implied warranties, including those of fitness
for a particular purpose and merchantability
(an unwritten warranty that the product is fit
for ordinary use), are limited to one year from
date of purchase.We will not pay for loss of
time, inconvenience, loss of use of your
or property damage caused by your RC or
its failure to work, or any other incidental or
consequential damages. Some states do not
allow limitations on how long an implied
warranty lasts or the exclusion of incidental
or consequential damages, so the above
exclusions or limitations may not apply to you.
RC,
To get warranty service for your RC,you
must provide proof of the purchase date.
Within 30 days of the date of purchase,
return your RC to the place where you purchased it for immediate replacement.After 30
days, call CLARITY at (800) 426-3738 for the
authorized service center nearest you.You
must prepay all shipping costs.We suggest you
save the original packaging materials in the
event you need to ship the RC.When in need
of warranty repair, please call our Customer
Service Department at (800) 426-3738
(VOICE) or at (800) 772-2889 (TTY).They
will help you process your return shipment.
This warranty does not cover defects resulting
from accidents, damage while in transit to our
service location, alterations, unauthorized
repair, failure to follow instructions, misuse,
use outside the United States or Canada, fire,
flood, and acts of God. Nor do we warrant the
product to be compatible with any particular
telephone equipment, party line, key telephone
systems or more sophisticated switching systems. If your
ranty, call us at (800) 426-3738 for advice as
to whether we will repair your RC and other
repair information.The repaired parts shallbe
warranted for 90 days.
RC is not covered by this war-
18
Page 24
CHAPTER 11
FEATURE SUMMARY
INDEX
Feature
Memory
Auto dialing M1
Memory scanning
No. of memory
scanned
Scanning speed
Remote dialing
Voice activated
answering
Remote flash
Voice mail indicator
Unanswered call
indicator
Headset operation/
control
Connection for Air Switch
or accessory switch
Back-up battery
provided
RC100
20
•
•
6
fixed
•
•
RC200
20
•
•
20
selectable
•
•
•
•
•
•
•
•
AC adapter..............................................................4
Air switch ................................................................9
Accessories and Switches ....................................9
Auto dialing ............................................................7
Batteries ..................................................................4
Channel setting ....................................................13
Connections............................................................4
Credit card calling..................................................8
Dial mode ................................................................4
FCC information..................................................14
Feature summary ................................................20
Flash ......................................................................5, 8
Headset, accessory ................................................9
Headset button ......................................................3
Installation................................................................4
Lapel microphone ..................................................9
Maintenance ..........................................................14
Memory dialing ......................................................6
Memory, programming..........................................6
Microphone ........................................................3, 6
Mounting ..................................................................4
On/Off button ................................................3, 6-7
Pause ........................................................................6
Pillow switch ..........................................................9
Power........................................................................3
Program....................................................................6
Pulse dialing ............................................................4
Quick start guide ................................................10
Redial ........................................................................8
Remote Transmitter ......................................4, 7-8
Remote Flash switch ....................................3-5, 8
Ringer volume..............................................3, 6,10
Scan ..................................................................4-5, 7
Scan rate ..................................................................5
Telebanking ..............................................................8
Tone dialing..............................................................4
Troubleshooting ..................................................12
Unanswered call indicator ..........................4-5, 8
Volume..................................................................3, 6
Voice Activation..............................................4-5, 8
Voice Mail Indicator ......................................4-5, 8
Warranty................................................................18
19
Loading...