Clarion QY8600 User Manual

Car Navigation

MODEL QY-8650

Navigation system manual

Features Names of Various Parts Basic method of use Basic Operations Basic Settings Source Media Mode Bluetooth Operation Navigation

��

Navigation System Settings Outline of Destination Entering Procedures Entering the Destination Route Guidance About Information

��

Table of contents

��

12 14 15 20 24 24 26 29 32

5 5

English

6 7 8

1

Warning

English

● When driving, the driver shall not operate….

The driver must park the vehicle in a safe place before operating the system.

● When driving, the driver must not read the navigation map…

Please refer to the voice prompts and follow the actual trafﬁc laws in driving.

● When driving, the driver must not watch the display of this unit….

Or the conditions at front of the vehicle may be neglected that may result in trafﬁc accidents.

● Please follow the actual trafﬁc laws to drive when using the navigation system as route guide or voice prompt…

If you drive only as per the route guided by the navigation system, you may violate the actual trafﬁc laws that may result in trafﬁc accidents.

● Do not use the equipment for a long time when the engine is off…

Or it will cause loss of electricity to the vehicle battery.

● Do not dismantle or modify this unit…

Or it may trigger accident, ﬁre or electric shock.

● Do not use the unit under such failure conditions as no display or no voice play…

Or it may trigger accident, ﬁre or electric shock. Contact NISSAN dealers.

Safety Precautions

● Stop using it immediately when there is any foreign object, water spill, smoke or bad smell and contact designated NISSAN dealers…

Continuous use may trigger accident, ﬁre or electric shock.

Caution

● The volume during driving shall be adjusted so that the sound outside the vehicle can be heard.

Or it may cause accidents.

● Pay full attention to operating this unit while driving so that safe driving is not affected…

Or it may affect driving and cause accidents.

● Do not use this unit for any purpose other than in the vehicle…

Or it may result in injuries or accidents.

● Never continue to use the unit in accidents…

Cut off the unit power supply if smoke, abnormal noise or smell is found.

● If the temperature inside the vehicle is high, use the unit after the temperature is lowered …

Or it may result in failure.

● Do not exert force on the screen

Or it may result in failure.

● Please follow the actual road trafﬁc lights to drive when using the navigation

Map contents may not be completely accurate due to trafﬁc development. Please keep in touch with the NISSAN Car dealers for timely update of map data.

2

Warning

● Changes or modiﬁcations to this unit not expressly approved by the party responsible for compliance could

including interference that may cause undesired operation.

void the user’s authority to operate the equipment.

NOTE:

This equipment has been tested and found to comply with

G

the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment

Radio

●The phenomenon of occasionally not receive radio sta- tion broadcast, noises or crosstalk during driving may be caused by road conditions, weather or environmental reasons.

USB

Not all USB memory devices are compatible with this unit due to different USB memory device models.

off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

z

Increase the separation between the equipment and receiver.

z

Connect the equipment into an outlet on a circuit differ-

z

ent from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

z

The device must not be co-located or operating in conjunction

with any other antenna or transmitter.

To comply with FCC’s and Industry Canada’s RF radiation exposure limits for

general population/uncontrolled exposure,this device must be installed to provide

a separation distance of at least 20cm from all persons.”

This device complies with Part 15 of the FCC Rules. Op-

Bluetooth

●Not all mobile phones are compatible with this unit due to different mobile phone models and functions.

Disc

●In cold or rainy days, water droplets may form inside the equipment as mist may condense on the window glass.

●This (condensation) will result in distortion or failure in playing. Please wait for a moment and use the equipment after ventilation or dehumidiﬁcation.

eration is subject to the following two conditions :

● This device may not cause harmful interference, and

● This device must accept any interference received,

English

3

●In order to protect the internal structure of the player, the player will stop playing automatically for protection when something abnormal occurs during the playing.

English

If the machine can’t operate normally even if you operate as per the displayed instructions, the machine may have malfunctions and you should contact NISSAN

dealers

●Distortion may occur if the vehicle is driven on the road of harsh conditions or is vibrated violently.

●MP3/WMA music ﬁles stored in CD-ROW/CD-R/CD- RW may be played.

●Because of the characteristics, scratches, stains on the CD/SACD/CD-ROM/CD-R/CD-RW disc or long-time use inside the vehicle, the disc may not be played due to the worsening disc performance. The disc mentioned above can’t be played if it has been ﬁnally treated or written in UDF format.

●Music CD should be ofﬁcially identiﬁed.

●This unit does not support 8-cm disc.

●Do not use any disc with transparent or translucent data reading side as it can’t be inserted, taken out or played normally.

●Please do not use any disc that is not from the legiti- mate manufacturer.

■Disc Storage

●Do not expose the disc to direct sunlight and make sure to put it inside the box, or the disc will deform and

can’t be used.

●No paper slip should be adhered to the playing side or identiﬁcation side of the disc or it will cause failure.

●Do not use any disc with crack or deformation, or it will cause failure.

.

●Do not touch the playing side of the disc (which is the smooth side with rainbow colours) when holding the disc, or ﬁngerprints will be left on the disc surface that may cause skipping.

●Playing a stained disc may result in disc scratch or skipping. Use disc cleaning agent available on the market to remove the stains on the disc by wiping softly from the inside to the outside.

■Use of New Disc

●When a new disc is used, there might be some burrs at the inner edge and outer of the disc that shall be removed with a ball pen or other means. Or the bur will adhere to the playing side of the disc that may cause skipping.

■Special- Shaped Disc

●Do not use any leased disc with glass ﬁlm, lease label or other adhesive. If such disc is played in the player, it will be hard to get it out and may result in failure.

■Disc of Special Shape

●No disc in the shape of heart or octagon may be played

4

or the machine will be damaged. Do not use such kind

2

4

1

3

5 6

7

8

!

9

@

0

of discs.

Names of Various Parts

Panel Buttons

■Disc Decoration

●Do not use any decoration to improve tone quality or

English

protect disc (such as disc case or protective case) as the change in the thickness or dimension of the disc may result in failure.

●Do not use any decoration to improve tone quality or shockproof performance (such as disc ring case or functional protective case), or the decoration may fall inside the machine that the disc can’t be played or taken out and result in failure.

LCD(touch screen): To display the working statuses of

LCD

●There will be brightened or darkened visual phenom- enon if you watch the LCD from the sides.

●The screen will become illegible under direct sunlight or external light on the display.

●If the machine is turned on when the temperature is below zero, LCD will appear to be darker than usual until the temperature inside the machine rises.

1

various modes.

SD card slot: Map SD card.

2

[CAMERA] button: To enter camera mode.

3

[D]Next Track button: In SB/iPod/Bluetooth Audio De

4

vice mode, short press it to select the next track to play, and long press it to Fast Forward; in AM/FM mode, short press to search radio station frequency up manually.

[A]Previous Track button: In USB/iPod/ Bluetooth

5

Audio Device mode, short press it to select the previous

-

track to play, and long press it to Fast Reverse; in AM/ FM mode, short press to search radio station frequency down manually.

[ BACK] button: Back to the previous mode.

6

[TUNE SCROLL] knob/[PUSH/SOUND] button: Rotate

7

5

English

to jump to previous or next touch key in the general mode; press and rotate the knob to adjust the sound effect or tone quality. Rotate to zoom in or out the map in the map mode.

8

button/[VOL] knob: Rotate to adjust volume; short

press to turn off/on audio device.

[AUDIO]button: To enter audio selection screen or Audio

9

Mode.

[

0

]Day/night button: Press to switch between day or

night mode.

[MAP] button: Press to enter the map screen.

!

[MENU] button: Press to enter Menu Screen to select

@

audio function or navigation function.

Caution

●It is prohibited to pull out the map SD card or the system will not work.

6

Basic method of use

Switching the language

When the unit turns on, the default language is set to English. Switch to your language to use the unit.

1

Press [MENU] button on the panel.

mobile phone mode.

English

Touch

2

Touch

3

Touch

4

Select the language and unit you

5

use.

to enter Settings Screen.

or slide the screen.

.

Setting the time

1

Press [MENU] button on the panel.

Touch

2

to enter Settings Screen.

Touch

3

Set the clock you need.

4

.

Mode Switch

■Switch to navigation mode

Press [MAP] button on the panel to switch to navigation mode for map display.

■Switch to Bluetooth mobile phone mode

Touch

switch to Bluetooth

■Switch to source mode

Press [AUDIO] button on the panel or touch such as Radio mode.

Press [AUDIO] button or touch

in Source mode to switch

to source selection screen.

to switch to source mode

7

English

Basic Operations

Main menu operations

On main menu screen you can enter corresponding work mode by touch the icons on the screen.

1

Press [MENU] on the panel or

touch screen.

to enter main menu

zChange page by dragging left or

right or touch

and .

Adjust Volume

1

Turn the [VOL] knob on the panel

to adjust the volume.

zSource mode: Adjust the volume of source. zBluetooth Mobile Phone mode: Adjust the

incoming call ringtone volume when receiving a call, adjust the outgoing call ringtone volume when making a call, or adjust the call volume when speaking on the phone.

zMap navigation: Adjust Voice Guidance

volume when voice guidance interrupt.

zParking guidance: Adjust parking guid-

ance volume in parking guidance.

For example, turn the volume knob in Source USB mode to adjust the volume as shown below.

Audio On/Off

When the radio or media player is ON, you can turn off the Audio device.

1

Short press

[ ]

button to turn off

Audio.

Short press

2

[ ]

button again to

resume playing.

Day/Night Display Mode Switch

This can switch the screen display mode.

1

Press [ ] button on the panel to

to switch between day and night.

Basic Settings

Press [MENU] button on the

1

panel.

8

zTurn the knob clockwise: volume up. zTurn the knob counter clock-

wise: volume down.

Touch

2

to enter Settings Screen.

Bluetooth Settings

Pair Bluetooth Mobile Phone or Bluetooth Audio Device / check the list of paired equipment/Set Bluetooth system of this unit.

NOTE:

* Pairing method of some mobile phones or

audio devices may differ or fail for Bluetooth pairing due to different types of mobile phones and audio devices.

1

Touch to enter

Bluetooth setting screen.

zWhen there is no Bluetooth pairing equip-

ment record, the items “Connect with Blue- tooth” and “Select Device” will be invalid.

Touch

2

to turn Bluetooth

On or Off.

Touch

3

to Select the mobile phone or audio device to connect. You can operate as per the information prompted.

Touch

4

to view and

select BT Device.

Touch

5

to edit

Bluetooth information.

Phone settings

You can conﬁrm and view various information concerning about the Bluetooth phone. Note: Before setting phone you need to

pair the mobile phone with this unit.

1

Touch to enter

Phone setting screen.

Touch

2

to edit and delete

Quick Dial number.

Touch

3

to view Call

History records.

Touch

4

to download

Phonebook.

Touch

5

Touch

6

to set Volume.

to turn the

Auto Downloaded on or off.

Audio Settings

To set various sound effects.

1

Touch to enter

Audio setting screen.

English

9

English

zAfter the screen display is OFF, the buttons

on the panel are still operational. Press

] button on the panel will resume

[ the previous source play screen or map navigation screen. Or you can press any button for the corresponding operation.

Touch

3

to enter brightness

adjustment screen.

ground colour adjustment screen.

Touch

2

, , , , or to

adjust the tone quality.

Display Adjustment

Adjust the display effect of the screen.

1

Touch to enter

Display Adjustment screen.

Touch

2

can be switched off to enter power save mode.

10

, the screen display

zTouch or to adjust the

brightness of display.

Touch

4

to enter contrast

adjustment screen.

zTouch or to adjust

the contrast of display.

Touch

5

to enter back-

zTouch or to change

the background colour.

Volume and Beeps

Adjust the Audio volume/Guidance volume/ Ringtone/ Incoming Call/ outgoing Call/NissanConnect Svcs, turn On or Off the button beeps and guidance voice.

1

Touch to enter

Volume & Beeps screen.

2

or

to adjust the vol-

ume.

Touch to turn on or off

3

button beeps.

Touch to turn on or off

4

guidance voice .

Edit menu

1

Touch to enter

Edit menu screen.

Touch

2

to delete the quick

menu.

Touch

3

Touch the quick menu to rear-

4

to add the quick menu.

range it.

Touch

5

to save the settings.

Voice Recognition settings

1

Touch to enter

Voice Recognition settings screen.

Touch

2

to turn on or

off Minimize Voice Feedback.

Touch to enter

3

the Audio device setting screen and you can activate the device by pressing “Yes” on the pop-up screen displayed upon connecting the media device.

Apple CarPlay settings

The connected device supports Ap-

ple CarPlay. Once Apple CarPlay is started, some NissanConnect features will be replaced or disabled by CarPlay including : NissanConnect Apps, iPod on USB Hands Free phone, Bluetooth Audio and navigation guidance on the Vehicle Information Display.

1

Touch to enter

Apple CarPlay settings screen.

Touch

2

to turn on or off Always Start Apple CarPlay. Turn on: the connected iPhone supports Apple CarPlay. When you connect an iPhone you can start Apple CarPlay by pressing “Yes” on the pop-up screen displayed. Turn off: the connected iPhone only supports iPod.

Touch to

3

English

11

displays Apple CarPlay Help information.

English

Source Media Mode

1

Press [AUDIO] button on the panel

or touch

screen.

FM/AM mode

1

Touch / to enter FM/AM

screen.

1

2

3

to enter source

Back to source screen.

1

View station list, RDS Info and

2

turn on or off HD radio mode.

Preset channel list(Station list). Up

3

to 12 channels can be saved.

SXM mode

Before to enter this mode you need to check the antenna.

1

Touch to enter SiriusXM

screen.

1 2 345

0 9

8 7

6

Channel category.

1

Channel name.

2

Artist name.

3

Song title.

4

Save the favorite channel by artist

5

or song alert.

Preset channel list(Station list).

6

Up to 18 channels can be

saved.

Switch the play mode between

7

replay and live.

SiriusXM signal intensity.

8

View track list by kinds of

9

categories etc.

Back to source screen.

0

USB mode

1

Touch to enter USB audio

screen when you connect a USB.

1 2

3 4 5 6 7

Back to source screen.

1

Select the folder and track, turn on

2

or off the display of album artwork.

Turn on or off repeat play.

3

Short touch: switch to Previous

4

Track; Long touch: Fast Backward.

Touch to Play/Pause

5

Short touch: switch to next Track;

6

12

Long touch: Fast Forward.

Turn on or off shufﬂe play.

7

iPod mode

1

Touch to enter iPod audio

screen when you connect an iPod.

Bluetooth Audio mode

Before playing Bluetooth Audio you need to pair the audio device with this unit.

1

Touch to enter Bluetooth

Audio screen.

AUX mode

Insert the external sound device into AUX slot via the audio cable.

1

Touch to enter AUX mode.

English

1 2

3 4 5 6 7

Back to source screen.

1

Select the track from playlist, art-

2

ists, albums, songs, podcasts, genres, composers and audiobooks; Turn on or off the Display of Album Artwork. Turn on or off repeat play.

3

Short touch: switch to Previous

4

Track; Long touch: Fast Backward. Touch to Play/Pause

5

Short touch: switch to next Track;

6

Long touch: Fast Forward. Turn on or off shufﬂe play.

7

1 2

3 4 5 6 7

Back to source screen.

1

View track list and select a track

2

to play it; enter the bluetooth settings screen.

Turn on or off repeat play.

3

Short touch: switch to Previous

4

Track; Long touch: Fast Backward.

Touch to Play/Pause

5

Short touch: switch to next Track;

6

Long touch: Fast Forward.

Turn on or off shufﬂe play.

7

Choose “Low”, “Middle” or “High”

2

input sense of auxiliary device.

Bluetooth Operation

Pair Bluetooth Device

1

Touch to select the

mobile phone or audio device to pair.

13

English

If you want to select the mobile

2

phone 秋to pair, touch

If you want to select the audio

3

device秋to pair, touch you have to edit the PIN (minimum 4 digits and maximum 16 digits) to pair the audio device.

.

, and

After entering the PIN, touch

4

and operate as per the information prompted.

After successful pairing, it will

5

automatically return to Bluetooth Setting screen.

Bluetooth Telephone

1

Touch to enter Phone screen.

Touch

2

delete Quick Dial number.

Touch

3

Phonebook.

Touch

4

History records.

Touch

5

number by keypad.

Touch

6

message.

Touch

7

phone with this unit.

Touch

8

paired phone.

Touch

9

to edit and

to view

to view Call

to dial phone

to view text

to connect a

to select

to set Volume.

14

Navigation

Menu Types and Operation

■Map menu (Menu on current location map)

Touch

display the Map menu at the left side of the screen. You can store the current location to the Address Book or change the map appearance.

1

2 3 4 5

[BACK] key:Return to the map

1

screen.

[Save Location] key:Save the cur-

2

rent location in the AddressBook.

[Nearby POIs] key:Displays the

3

Category screen of the POIs nearby the current location.

[Map View] key: Change the types

4

of the screen and map appearance.

[Map Icons] key: Turn on or off the

5

on the map screen to

map icons.

■Location menu (Menu on scrolled map)

After scrolling the map by touching

the Map screen, touch

on the

screen to display the Location menu at the left side of the screen. You can set the location under the cursor at the centre of the screen as the destination or store it to the Address Book.

1

2 3 4 5

[BACK] key: Returns to the

1

scrolled Map screen before

touching the

[New Destination] key:Sets the

2

key.

location under the cursor as the destination. When a destination is already set, the old destination is cancelled as soon as the new

destination is set.

[Add to Route] key:When another

3

location is already set as the destination, you can set the location under the cursor as a waypoint. Touching this key displays the Edit Route screen. Specify the desired order of passing to set the location as a waypoint.

[Nearby POIs]] key: Displays the

4

Category screen of the POIs nearby the location under the cursor.

[Save Location] key:Save the

5

location under the cursor in the Address Book.

Map Screen Features

■Types of the map

There are two types of map: the 2D map and the 3D map. Such as the method of scrolling the map, some operation are different depending on the map types.

●2D Map

English

15

English

The 2D map is a map screen represented to the plane just like the map of atlases. It is suitable for searching a destination and conﬁ rming the road or route.

●3D Map

The 3D map is a map screen using a viewing position above the vehicle while looking in the direction of the car heading. It is suitable for understanding the image of the direction, because the perspective of the travelling direction can be adjusted as required.

■Indicators on the map

Indicators displayed on the Map screen are different according to the conditions at that time.This section explains the main indicators displayed on the Map.

Indicators on the map of the current location

1

2

3 3 4

Audio mark: Indicates the current

1

source mode.

Vehicle mark:Indicates the current

2

location and direction of your vehicle.

[

3

]Map Menu key:Displays the

Map menu.

[

4

]Map scale key: Touch this

key to decreases/increases the map scale.

[

5

]Map bearing mark:Indicates

the map orientation. You can switch the map orientation between Heading Up, North Up and 3D map by touching this icon.

Indicators on the scrolled map

Indicators are displayed after scrolling the map. During scrolling, only the scroll cursor is displayed on the map.

[

1

] (Slow Scroll)key: Displayed

only on the 2D map. Turn on the Slow scroll mode. Scroll cursor: Displayed when scrolling the map.

Displays the name of the street

2

under the cursor.

Indicators displayed during the route guidance mode

After a destination is set and travel-

1

2

3

16

ling is started, the guidance route and various guidance information are displayed on the map.

1

2

3

Small Turn Arrow display:Displays

1

the turning direction and distance to the next guidance point.

Guidance point:Indicates the

2

guidance point

Distance to the waypoint/

3

destination:The distance from the current location to the next waypoint or destination are displayed.

Manipulating the Map Screen

■Scrolling the map

Touching the Map screen displays a cursor at the centre of the screen, and you can scroll the map. For the 2D map, touch the map to move the map to the touched position, and keep touching the map to scroll the

map towards the touched direction. For the 3D map, touch the upper part of the map to scroll the map toward the touched direction, and touch the left or right part to rotate the map while touching.

■Slow scroll mode operation

Touch

while scrolling the 2D map

to display the following screen:

Keep touching the desired arrow key (

, , , , , , , .) moves

the map slowly towards the corresponding direction. To quit the slow

scroll mode, touch

.

■Zooming IN/OUT the map

1

Touch to display the zoom in/

out key.

Touch

2

or to change the

map scale.

■ Changing the map appearance

The Map screen can be adjusted regarding orientation or appearance of the map.

1

Touch on the Map screen of

the current vehicle location.

Touch

2

to enter Map

View screen.

English

17

English

zTouch the corresponding key

to change the map view.

Touch

3

View Settings screen.

to display the

Screen examples

• 2D Map

2D/3D Map

z [Intersection]:During the route guid-

ance mode, displays the Intersection Close-up display which displays the turning direction of the next guidance junction at the left of the screen.

z[Turn List]:During the route guidance

mode, displays the list of the name, distance, and turning direction of the guidance junctions at the left of the screen.

z[Drive Report]:During the route guid-

ance mode, displays the Drive Report.

z[Full Map]:Changes to display

one map using full screen.

18

• 3D Map

2D/2D Map

Touch

4

to enter Map

Settings screen.

●[Map Orientation] key: Changes the orientation of the map between Heading Up and North Up.

zThis control is available

when [2D] is selected.

●[Long Range] key: Changes the map view to view a wider area in the direction that the vehicle is travelling. When this feature is activated, the vehicle mark is located slightly lower than the centre of the screen.

zThis control is available when [2D]

is selected and the Map Orientation is set to Heading-Up.

●[Map Colour] key:Selects the colours(Map Colour 1/2/3/4) of the map.

●[Map Text Size] key: Change the map text size(Large, Medium,Small).

●[Birdview Angle] key: Changes the angle of the 3D map. Touch

raise the angle, and

to lower

to

the angle.

zThis control is available

when [3D] is selected.

●[North Up when Zoomed Out] key: Turn on or off north up when zoomed.

●[Names Displayed on Map] key: Change the names of place, facil-

ity and road displayed on map.

●[Left Split Map Settings] key: Change settings of Map Orientation, Long Range and Map Scale of left split map.

●[Show all Freeway Exits on Route] key: Turn on to show all freeway exits on route.

●[Auto. Show Turn List on Freeway] key: Turn on to show turn list on freeway.

Navigation System

Settings

Press [MENU]/[MAP]/[AUDIO]

1

button on the panel to display the function bar.

Touch

2

Navigation Settings Screen.

, to enter

English

Registering/Editing the Address Book

From the Address Book, you can register the home address, addresses of facilities and places, routes, and Avoid Areas. You can also edit the data registered.

The registered places or routes can be set as the destination or as the current route.

19

■Home Location

Register your home address. You can edit the registered home address.

English

To register the Home Location

The Home Location can be registered when the key is displayed.

1

Touch .

Search for the location of

2

your home by a similar way as for entering destinations.

Touch

3

To edit the Home Location

1

Touch to enter edit Home

to register it.

Location screen .

Touch the desired Item to edit it.

2

Touch

3

to adjust the

location by moving the cursor on

the Map screen.

Touch

4

to delete the regis-

tered Home location.

Touch

5

■Stored Locations

Registers locations in the Address

to register it.

Book. You can register up to 200 locations, and can also edit the registered locations.

To register Location

1

Touch .

Touch

2

Search for the location you wish

3

.

to register by a similar way as for entering destinations.

Touch

4

Touch

5

to register it.

to sort the locations by number,name, icon and group.

To edit a Stored Location

1

Touch .

Touch the name of the Stored

2

Location you wish to edit.

Refer to “To edit the Home Loca-

3

tion” on Page 秋20秋to edit it.

■Stored Routes

Registers the current route. You can register up to 5 routes, and can also edit the registered routes.

To register the current route

1

Touch .

2

Then touch from the

3

displayed conﬁ rmation screen.

To edit the Stored Route

1

Touch .

Touch the name of the Stored

2

Route you wish to edit.

Touch the desired item, then edit

3

it.

●[Rename] key: Changes the name of the Stored Route.

●[Replace] key: Replaces the Stored Route with the current route.

●[Delete] key: Deletes the Stored Route.

Touch

4

to register it.

■Avoid Area

You can register areas you do not

20

want to pass or areas that often get congested as an Avoid Area. When you register the Avoid Areas, you can set the system to calculate routes avoiding the registered areas. Up to 10 Avoid Areas can be registered. You can edit the registered Avoid Areas.

To register an Avoid Area

1

Touch .

Touch

2

Search the area to avoid by a

3

.

similar way as for entering a destination.

Touch

4

To edit an Avoid Area

1

Touch .

Touch the name of the Avoid Area

2

to register it.

you wish to edit.

Touch the desired item to edit,

3

and edit it by similar way as for registering Avoid Areas.

●[Rename] key:You can change the name of the Avoid Area. Enter the

name, then touch

.

●[Move Location] key:You can ad-

just the location of the Avoid Area.

●[Resize Area] key:You can change the size of the Avoid Area([Large], [*], [Medium], [*], or [Small]), then

touch

.

●[FWY] key:You can set whether to avoid freeway passing the Avoid Area.

●[Delete] key:Deletes the current Avoid Area.

Touch

4

to register it.

■Deleting the Stored Items

You can delete various data stored in the navigation system.

1

Touch .

Touch the item key to delete.

2

●[Delete Home Location] key: De- letes your home location.

●[Delete Address Book] key:

z[Delete All]:Deletes all the stored locations. z[Delete 1 Entry]:Deletes only the location

that you specify on the Delete One screen.

●[Delete Stored Routes] key:

z[Delete All]:Deletes all the stored routes. z[Delete 1 Entry]:Deletes only the route that

you specify on the Delete One screen.

●[Delete Avoid Areas] key:

z[Delete All]:Deletes all the

stored avoid areas.

z[Delete 1 Entry]:Deletes only the avoid area

that you specify on the Delete One screen.

●[Delete Previous Destination] key:

z[Delete All Previous Destinations]:Deletes

all the registered previous destinations.

z[Delete Previous Destination]:Deletes only

the previous destination that you specify on the Delete Previous Destination screen.

z[Delete Previous Starting Point]:

Deletes the starting point.

From the displayed conﬁ rmation

3

screen, touch

.

■Transfer Address Book

You can Transfer Address Book from SD card.

1

Touch .

●[Export Data] key:Export data to SD card.

●[Import Data] key:Import data from SD card.

Navigation Settings

■Map View

Please refer to “Changing the map

English

21

appearance” on Page 秋17秋 .

■Map Icons

Switches ON or OFF Landmark icon

English

display for each type.

1

Touch .

Touch the desired item key you

2

wish to change the setting.

The types of icons that can be set

3

are the following 6 types.

● [Restaurant] key

● [ Station] key

● [Hotel] key

● [ATM] key

● [Rest Area] key

■Guidance Settings

You can change settings concerning the guidance.

1

Touch to enter

Guidance Settings screen.

Touch the desired menu item to

2

set.

●[Guidance Volume] key:Adjusts the volume of the voice guidance.

●[Guidance Voice] key: Sets wheth- er to activate the voice guidance.

●[Trafﬁc Announcement] key: Sets

whether to read out the trafﬁc information.

●[Intersection Guidance Settings] key: The Intersection Guidance Settings screen is displayed. You can set the intersection guidance for Level1, Level2,Level3 and Level4.

●[Estimated Time] key:Changes the setting of arrival time indication displayed on the Map screen.

z[Destination]:Sets to display the ar-

rival time to the destination.

z[Waypoint]:Sets to display the arrival time

to the next waypoint or destination.

■Route Settings

You can change settings concerning the route guidance.

1

Touch to enter route

Settings screen.

Touch the desired item key.

2

●[Basic Route Type] key:You can change the conditions of route calculation.

z[Fastest Route]:Calculates the route of

which the required time is shortest.

z[Minimise Motorways]:Calculates

the route of which motorways are not used as much as possible.

z[Shortest Route]:Calculates the route

of which the distance is shortest.

●[other Routing Choices] key:You can specify other route calculation methods.

z[Minimise Toll Roads]: Mini-

mises the use of toll roads.

z[Use Time Restricted Roads]:Uses

roads with restricted usage time.

z[Use Real Time Trafﬁc Information] :Con-

siders the trafﬁc information for routing.

z[Use Avoid Area Settings]:Takes a de-

tour to avoid the registered Avoid Area.

z[Use Ferries]:Uses car ferries for routing. z[Use Learned Routes]:Considers

the Learned Routes for routing.

z[Use HOV Lanes]:Uses HOV

lanes for routing.

z[Auto Reroute]:When leaving the suggested

route during the route guidance mode, a new route is automatically recalculated.

■Trafﬁc Information Settings

You can set the various functions concerning the trafﬁc information.

1

Touch to enter the

Trafﬁc Information Settings screen.

Touch the desired key on the

2

screen to set it.

●[Use Trafﬁc Information] key: Con- siders the information.

●[Show Incidents on Map] key:

22

Switches on or off the trafﬁc information display on the map.

●[Show Trafﬁc Flow on Map] key: Switches on or off the trafﬁc ﬂow display on the map.

●[Trafﬁc Announcement] key: Switches on or off the trafﬁc announcement standby mode.

■Others

1

Touch to enter the Others

settings screen.

●[Map Scrolling Information] key: When you scroll the Map screen and move the cursor on an icon, the information on the location can be displayed. You can set this function whether to activate or not.

z[Address Book Icons] key z[TMC Trafﬁc Icons] key z[Destination/Waypoint Icons] key z[Latitude/Longitude Info.] key

●[Customize nearby POIs] key:You can customise the ﬁve categories of the Customize nearby POI feature.

●[Keyboard Type] key: To change the keyboard type(QWERTY type and ABC type).

●[Tracking Dots Displayed on Map] key: To change the setting of the tracking dots displayed on map.

●[Adjust Current Location] key:You can correct the vehicle position on the Map screen by Scroll the map.

■Resetting All Navigation Settings to Defaults

You can reset all the Navigation settings to return to the factory settings.

Note:

GThough all the settings are reset, the

stored data such as the Address Book, Stored Routes, and Avoid Area are not erased.

1

Touch

.

Then touch from the

2

displayed conﬁrmation screen.

Outline of Destination

Entering Procedures

To start route guidance, operate the navigation system with the following procedure:

●Select the method of searching destination from the Destination

menu screen, then search for the desired destination.

Select a suitable searching method according to the place to search.

●Conﬁrm the position of the place found with the Set Location menu screen, then start the route guidance.

You can store the place found to the Address Book, or can conﬁrm the information according to the place, as well as set it as destination. You can also display other suggested routes, or conﬁrm information of the route.

Setting destination by entering the address

This section explains the basic operation procedure to set the destination in detail, using the example to specify the destination by entering the address from the Destination menu. Read this explanation thoroughly because this procedure is similar to other destination entering methods.

English

23

For other destination entering methods, please refer to “Entering the Destination” on page 秋25秋.

1

English

Press [MENU]/[MAP]/[AUDIO]

button on the panel to display the function bar.

Touch

2

to enter Destination

screen when no route exist.

Note:

G You can omit the state/province name

entry and directly enter a road name. Proceed to step 9.

Touch

5

to enter the city name you wish to go to by touching characters on the screen. Then, the system returns to the Street Address screen. Enter the street name by the same way.

Touch

6

to enter the street

name you wish to go.

Touch

7

to enter the house number input screen. Then enter the house number by touching numbers on the screen, touch

Note:

GYou can omit the house number entry.

Proceed to step 9.

Conﬁrm the entries, then touch

8

.

zYou need to touch to enter

Destination screen when a route had exist.

Touch

3

to enter

Street Address screen.

24

Touch

4

to enter the state/province name you wish to go to by touching the characters on the screen.

Note:

GDuring the character entry, the system

shows the city name list automatically when all the matching cities can be displayed on one page.

●[Start] key:Sets the location shown by the “ ”on the map as the destination, and starts the route

guidance.

●[Route Details] key: The Calculate Route menu is displayed. You can change the route search conditions or check the route information.

●[Move Location] key:The Map screen is displayed. You can adjust the location of the destination.

●[Add to Route] key:When the desti- nation is already set, the speciﬁed location is set as the waypoint.

●[Save Location] key:Save the speciﬁed location into the Address Book.

●[Details] key:Displays information about the speciﬁed place if it is included in the map data.

Touch , the route guidance

9

will be started. The place found is shown with “ ” on the map.

Entering the Destination

Searching Your Destination from the Destination Menu

You can search for a destination from the Destination menu by using various methods. Use a suitable search-

ing method according to the place you wish to go to. Destination menu screen

For the operation procedure hereafter, see the explanation of each section.

■By Street Address

For the operation procedure, refer to “Setting destination by entering the address” on page 秋21秋.

■By Nearby Points of Interest

1

Touch .

Touch your desired category.

2

An example of specifying RESTAURANT is explained below.

Touch the place you wish to go

3

from the displayed place list.

Conﬁrm the location of the desti-

4

nation, then touch

.

■Going Home

When your home address is registered, you can start route guidance to your home by a simple operation.

Note:

GWhen your home address is not

registered, a message is displayed when touching the [Home] key. Register it by touching the [Yes] key. When the list of searching methods appears, register your home address by the desired method.

English

25

1

Touch .

Touch

2

The route to your home is automati-

English

cally calculated and the route guid-

.

ance is started.

■By Previous Destination

The destinations previously used are registered in the previous destination list (up to 100 locations). You can enter a destination by selecting it from this list. When the previous destination list exceeds 100 items, the oldest entries are automatically deleted.

1

Touch .

Touch the place you wish to go

2

from the displayed history list.

Touch

3

.

■By Points of Interest (POI)

Select the category of the place, narrow down the data by specifying the area or entering the name, and then select the place you wish to go to. By touching , you can also search a place by simply entering the name.

1

Touch .

Touch your desired category. For

2

example

. When a additional

category list is displayed, touch a category again to select one.

Set the narrow down conditions

3

for the places.

●[By Name] key: Input the facility name to narrow down the target place.

●[Select a City] key: Input the city name to narrow down the target place.

●[Near Current Location] key: Shows a list of facilities around the current location.

●[Near Destination] key: When the destination is set, shows the list of facilities around the destination.

An example of specifying By Name is

explained below.

Touch

4

. Enter the facility

name, and then touch .

●[By Distance] key:Sorts the list by nearby order.

●[New Category] key:Displays the Category screen so you select a new category.

Touch the place you wish to go

5

from the displayed place list.

Conﬁrm the location of the desti-

6

nation, then touch .

■By Address Book

Speciﬁes a place registered in the navigation system as the destination. Note:

• To use this function, register places

beforehand.

1

Touch .

26

Touch the stored location you wish

2

to go from the displayed Address Book list.

Conﬁrm the location of the desti-

3

nation, then touch

.

■By Intersection

An intersection of any two streets can be set as the destination.

1

Touch .

Enter the 1st street and the 2nd

2

street, then touch

Touch

3

.

■By Phone number

If the telephone number of the facility is available, use this to ﬁnd the facility by entering the number.

Note:

GTelephone numbers that were stored

for stored destinations can also be used.

GIf the area code of the speciﬁed

telephone number does not exist in the map data, the system will not search for the location.

GOnly the locations included in the

database in the map data can be

searched by the phone number.

GResidential phone numbers cannot be

used to search for a location.

1

Touch . Enter the

phone number including the area code, and then touch

Touch the place you wish to go

2

.

from the displayed place list.

Touch .

3

■By Freeway Entrance/Exit

The entrance or exit of a freeway can be set as the destination.

1

Touch to enter

the character input screen. .

Enter the name of the freeway,

2

then touch

. Freeway list dis-

played.

Touch the place you wish to go

3

from the displayed freeway list.

Touch .

4

■By City Center

The centre of a city can be set as the destination.

1

Touch to enter

the character input screen.

Enter the name of the city, then

2

touch

. The city centre list

displayed.

Touch the place you wish to go

3

from the displayed place list.

Touch .

4

■By Stored Routes

Selects a route previously registered, then set it as the new route. Note:

• To use this function, one or more

registered routes are required.

1

Touch .

Touch the route you wish to go

2

from the displayed stored route list.

Touch

3

.

■Searching Your Destination from the Map Screen

You can search for a place by scrolling the map, and set it as the destination.

1

Scroll the map by touching the

Map screen, and move the cursor

English

27

English

to the place you wish to go to. Touch

Conﬁrm the location of the desti-

2

nation, then touch

.

●[More Routes] key: You can change to other suggested routes with a different priority condition.

●[Route Info] key: Shows the information of the suggested route selected on the screen.

●[Add Waypoint] key: Adds waypoints to the suggested route displayed on the map. Up to ﬁve waypoints can be speciﬁed.

Touch

3

Note:

GWhen you search a place far from the

current location, change the map scale to search more quickly.

.

Route Guidance

After you have entered the destination and started the route guidance, you will be guided along the route by screen display and by voice.

Route Guidance Screen Features

As well as the Map screen, various guidance screens are displayed during the route guidance mode according to the situation. Pressing the [MAP] button to switch the screen between the following guidance screens and the full map screen.

■Junction Map

When you get near to approx. 300 m or 300 yd (1 km or 1 mile for a motorway) from the next guidance point, the screen will be divided into two displays and the Junction Map will be displayed on the left display. You can set to display the Junction Map screen always in the route guidance mode. The default setting is

OFF.

Note:

GBefore the Junction Map is displayed,

a voice guidance will be heard at approx. 600 m or 0.4 miles (2 km or

1.3 miles for a motorway) from the next guidance point. You can change this setting by setting the Junction Guidance Settings.

1 2

Remaining distance indication:

1

3

Indicates the remaining distance to the next guidance point with the bar gauge.

Guidance route: Indicates the

2

direction to travel.

Guidance point:Indicates the next

3

guidance point.

■Turn list on Route

The screen is always divided into two displays and the Turn List on Route is displayed on the left display

28

if Turn List is activated. The Turn List contains the guidance points next to the vehicle position, and will change while travelling. When you get near to the next guidance point, the left display is automatically changed to the Junction Map. You can set to display the Turn List screen always in the route guidance mode.

1

Turn List:The list of the guidance

1

points and turning directions are displayed from the items near to the vehicle position, and it will change while travelling.

Scrolling key:Scrolls the Turn List

2

on Route screen.

2

About the Voice Guidance

After starting the route guidance, not only guidance by screen but also guidance by voice, such as the turning direction or the distance to the guidance point, will be given when you get near to the guidance point. You can set whether to use the voice guidance or not, and set the volume to be changed according to the vehicle speed.

Changing/Editing the Route Settings

From the Route menu, editing the current route, conﬁrming the route information, setting the conditions of the route calculation, etc. can be performed.

1

Press [MENU] button on the panel.

Touch to enter Route menu

2

screen when a route had exist.

■Delete the route guidance

Delete the route guidance/Terminates the route guidance during the route guidance mode.

1

Touch . A conﬁr-

mation message is displayed.

Touch

2

ance will be terminated, and the destination and route will be deleted.

■Conﬁrming the route information

Conﬁrm various information of the current route.

1

Touch to enter

Route Info. screen.

, the route guid-

English

29

English

●[Turn List] key: Display the list of route information. The guidance points from the current location to the destination are displayed with the list format.

●[Simulation] key: Simulate the route guidance with moving the vehicle mark automatically on the Map screen.

●[Store Route] key: Store the speci- ﬁed route. A maximum of 5 routes can be stored, and they can be easily retrieved.

●[Map Scroll] key: Displays the Map screen where the speciﬁed route can be conﬁrmed.

Touch the desired item to view

2

the information.

■ Editing the route

You can edit the current route.

1

Touch to enter

the Edit Route screen.

[Add Destination] key: Touch this

2

key when you want to set a new destination. The original destination will be set as a waypoint in the route.

●[Add Waypoint] key: Up to 5 way- points can be set. The speciﬁed waypoints are displayed by marks with the ordinal number for visiting.

●[(Current destination/waypoint name)] key: You can touch the name of the current destination or waypoints you wish to edit.

●[(Route calculation criteria)] key: You can change the conditions of route calculation.

z[ECO Route] z[Fastest Route] z[Minimize Freeway]

z[Shortest Route]

Change settings by touching the

3

desired setting item.

Touch

4

, The route is recal-

culated with speciﬁed conditions.

■Route settings

You can change settings concerning the route guidance. About the details, please refer to “Guidance Settings” on page 秋21秋and “Route Calculation Criteria” on page 秋22秋.

■ Recalculating the route

After changing the conditions of the route calculation or when the status of the route is changed, you can recalculate the route if you want.

1

Touch , the route

is automatically recalculated, and the Calculate Route screen is displayed.

Touch

2

, the route guidance

will be restarted.

30

■Setting a diverted route using

trafﬁc information

The route with trafﬁc information considered is automatically calculated, and the route guidance will be restarted.

1

Touch . The

diverted route is displayed with TMC trafﬁc information taken into account. When no diverted route is found, a message is displayed.

Conﬁrm the diverted route, then

2

touch

.

■ Setting the diverting distance

Search for a diverted route where the section from the current location up to the speciﬁed distance is avoided.

1

Touch to enter

the Detour screen.

Touch the distance you want to

2

avoid. The route where the section of selected distance is avoided is automatically calculated, and the route guidance will be restarted.

About Information

This screen sets or displays various information that is helpful for using the vehicle safely and comfortably.

Press [MENU] button on the

1

panel.

Touch to enter Info screen.

2

Touch the desired item to view the

3

information, and about some items you can operate as per the information prompted.

English

31

Clarion QY8600 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual