Clarion PSWGMTK User Manual
PSWGMTK
Behind
Seat
Mount
Camouflage Powered
Subwoofer
Chevrolet S-10 I Chevrolet
Clarion
Fits '95 - 2000 ChevroletS-10
'95 - '98 Chevrolet
PREPARATION '
PARTS
LIST
(QTY) Component
Pre-Assembled
(1) Roto-Molded Subwoofer Enclosure
(1) 8", 2 Ohm Subwoofer
100W
Class
"0"
(1)
(1) Speaker Grills
(1) Foam Ring for Grille
LooseParls
(1) 17' Wire Harness w/Pigtail Style Connector
(2) Mounting Brackets
(4) 3/4" Pilot Point Wafer Phillips Head Screws
(4) 1" Self-Tapping Phillips Head Screws
(1) 1/2" Ground Screw
Washer
(1) Star
Wiring:
Amplifier
1 Green
2 Violet/Black
3 Green/Black
4 Violet
5 Blank
6 Black
7 BluelWhite
8 Yellow
Full
Size Pick-up Truck
and
GMC Sonoma
Full
Size Pick-up Trucks (extended cab only)
OVERVIEW
The Clarion Camouflage subwoofer system provides for the installationofa low frequency driverinan enclosure which is
powered by a small low current, high power class
low current consumptionofthe amplifier at high power levels The class
"0"
(Digital) amplifier The advantage to using this typeofamplifier isinthe
"0"
amplifier pl\)vided with this system will produce a
rated 100Winto a 2 ohm load The woofer supplied with this system uses a voice coil with rated impedanceof2 ohms, and
therefore is not considered a standard woofer Replacing the woofer with any driver having an ;mpedance greaterthan 2 ohms
will yield lower power output from the amplifier, and is not recommended
PROCEDURE
Properinstallationofthis
of
the outlined tasks below, contact a professional installation facilitytoperform the work
OUTLINE
• Remove the head unit
- Connect the Clarion "T" harness between the radio and factory wiring and route the harness in the vehicle
• Install mounting brackets onto subwoofer enclosure
- Test subwoofer enclosure and head unit functions (fade, balance,
- Adjust subwoofer gain
• Install the enclosure
• Re-assemble the vehicle
THIS DEVICE COMPLIESWITH PART15OFTHE FCC RULES. OPERATION IS
TWO CONDITIONS.
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE,
(2) THIS DEVICE MUST ACCEPT
CAUSE UNDESIRED OPERATION
product requires proper
ANY
tools
and knowledgeofcar
etc)
audio principlesIfyou are
SUBJECT
not
comfortable performing any
TO THE FOLLOWING
AND
INTERFERENCE RECEIVED, INCLUDING INTERFERENCETHAT MAY
- 1 -
la.
WIRING
USING
A
CLARION
"T"
HARNESS
IThere
STEP1:Remove the
STEP 2:
A Unplug factory wires from radio
B Plug
C
STEP
STEP
STEP 5: TEST
are2methodstoconnect
Radio
Connect
the
(SEE
Connect
"T"
DIAGRAM
3:
Route the wire
- behind the
- under
4:
Connect
near
Turn on the system and be sure all
speakers are working properly
Set the subwoofer amplifier gain
a suitable level
the
"T"
harness
the
the
in line with
1 )
BLACK wire on
driver
the
rear
the
amplifier ground wiretoa clean chassis ground
subwoofer enclosure
and
SET
Harness
harness
seat. drivers side (Full size trucks)
the
"T"
seat (S-10 /
GAIN.
this
producttothe
the
radio wiring
harness to radio chassis
from
the
radio to;
Sonoma)
to
vehicle.
(DIAG.1)
Please
refertosectionlaandIbfor
UsingaClarion
CONNECT
TO
RADIO
CHASSIS
FACTORY
RADIO
GAIN
ADJUSTMENT
"T"
HARNESS
EXTENSION
-,f-----_ll:-
each.
.......
lb. WIRING USING THE SUPPLIED HARNESS
STEP 1: Remove
STEP 2:
Yellow:
Black:
BluelWhite:
Green:
Green/Black:
Violet:
Violet/Black:
STEP
STEP
STEP 5: TEST
Connect
ConnecttoConstant 12V Power
ConnecttoRadio
ConnecttoLeft
ConnecttoRight
3:
Route
- behind
under
-
4:
Connect
subwoofer enclosure
Turn on
speakers
Set
the
Radio
the
wires
GroundorChassis
ConnecttoAmp/Antenna Turn-on Lead
Rear
Speaker (+) Positive Lead
ConnecttoLeft Rear Speaker (-) Negative Lead
Rear
Speaker (+) Pqsitive Lead
ConnecttoRight Rear Speaker (-) Negative Lead
the
wire harness from the radio to
the
driver seat (S-10 / Sonoma)
the
rear seat drivers side (Full size trucks)
the amplifierground wire to ground
and
SET
the GA/N
the
system andbesure all
are
working properly
the
subwoofer amplifier gaintoa suitable level
near
the
Using
(DIAG.2)
the
Supplied
FACTORY RADIO
AFTERMARKET
CONNECTTOGROUND
Harness
or
RADIO
CONNECTTOGROUND
-
2-
I Sonoma
of
the enclosure
the mounting brackets through the dimples using the (4)
2.
Full
Size Trucks
A Position enclosure so speakerfaces up
B Locate the two dimples on the each side
so
the brackets will
attach as shown in diagram below
C Screw in the mounting brackets through the dimples using the (4)
supplied pilot pointwafer head screws
Subwoofer
Enclosure
of
truck behind the driver seat (S-10 I Sonoma)
of
any paintorresidue)
Subwoofer
Enclosure;
etc)
$-10
Truck
Full size
Truck