Page 1
INSTALLATION AND WIRE
CONNECTION MANUAL
English
1. SAFETY PRECAUTIONS
❏Symbol Identification
This manual uses symbols and icons to
indicate safety precautions and concerns
during the installation procedure. Be sure
to carefully read and understand each
precaution prior to beginning the installation.
WARNING
•This symbol is intended to alert the
user to the presence of important
operating instructions. Failure to
heed the instructions may result in
severe injury or death.
CAUTION
•This symbol is intended to alert the
user to the presence of important
operating instructions. Failure to
heed the instructions can result in
injury or material damage.
❏Before Use
WARNING
•Confirm the battery voltage of the
vehicle to be installed. This unit is
designed only for vehicles with DC
12V power supply.
•Disconnect the negative terminal of
the battery before connecting wires,
otherwise an electric shock, injury
by short circuit may occur.
Car battery
❏Installation Precautions
WARNING
•When installing the unit to a vehicle
with an airbag system, never install
it in a place where it may affect the
operation of the airbag.
•Do not install this unit in the
following locations:
A location interfering with the
driver’s visual range or operation.
A location where the gear shift or
brake pedal are hindered.
A location where passengers are at
risk.
An unstable location, or where the
system may fall.
CAUTION
•Do not install the system in the
locations described below. This may
cause a fire, accident or electrical
shock:
A location exposed to rain or dust.
An unstable location, or where the
system may fall.
•Do not install this unit in a place
exposed to direct sunlight, heat or a
place where the vent holes or heat
radiation holes are covered.
•When you install the antenna, mount
it in a place where the elements of
the antenna do not protrude beyond
the edge of the front, back, left and
right of the vehicle.
If it comes in contact with
pedestrians, it may cause an
accident.
•Ensure a minimum distance
around the apparatus for sufficient
ventilation.
•Do not place naked flame sources,
such as lighted candles on the
apparatus.
•Use the apparatus only in moderate
climates (not in tropical climates).
❏Installation Notes
WARNING
•Please note the position of pipes,
tanks and electrical wirings before
installing the unit into the vehicle;
failure in avoiding these may cause
a fire or malfunction.
CAUTION
•Use only the supplied parts.
If unspecified parts are used, they
may cause damage.
•Any holes made in the body of the
vehicle should be sealed with a
silicon adhesive.
If exhaust fumes or water penetrates
into the vehicle, this may cause an
accident.
•Fasten the bolts securely when
installing the unit. If the bolts are
loose an accident or malfunction
could occur.
54 NX504E/FX504E
Page 2
❏Connection Notes
WARNING
•Loom all cables according to the
instruction manual, so as not to
hinder operation.
•Wire the connecting cords/cables
away from high temperature areas.
If the coatings of the cables melt,
it could cause an accident/fire by a
short circuit. Take care when wiring
in the engine compartment.
•When wiring the connecting cables
in a vehicle with an airbag system,
never feed the cables through
a place where it may affect the
operation of the airbag.
An airbag not operating correctly in
an emergency may cause increased
injury.
CAUTION
•Verify wires with a digital multi-meter
prior to making any connections.
Many new vehicles use multiplexed
and/or low voltage circuits that can
be damaged if a test light or logic
probe is used.
•Connect cables appropriately. If a
wrong connection is made, this may
cause a fire or accident.
•When passing cables through
the body of the vehicle, use nonconductive grommets.
If the coatings of the cables are
worn out by rubbing, this may cause
an accident, fire or a short circuit.
•After wiring cables, fix them with
insulation tape.
•Be sure to switch off the vehicle
when connecting or disconnecting
cables to/from the unit, otherwise
an electric shock, injury or accident
may occur.
2. PACKAGE CONTENTS
Main unit
Quick Start Guide & Installation
Manual
CD-ROM
•Owner's manual
•Owner's manual - Navigation (NX504E
only)
Power supply cable
RCA pin cable (6ch)
RCA pin cable (Rear AUX-IN/Rear
Video Out)
Bag for accessories
•Flat head screw (M5 × 8 mm)
............................................................8
•Hexagonal bolt (M5 × 8 mm)
............................................................8
•Electro tap...........................................1
•Rubber cap (for RCA pin cable)
..........................................................10
•Cable holder (NX504E only) ................3
•Double-sided tape for fastening GPS
antenna (NX504E only) .......................1
•Cable tie ..............................................1
Warranty card
GPS antenna (NX504E only)
USB Cable
Notice
•Theprovideddisc(CD-ROMmanual)
cannotbeplayedbackonthisunit.
3. GENERAL CAUTIONS
●Do not open the case. There are no userserviceable parts inside. If you drop
anything into the unit during installation,
consult your dealer or an authorized
Clarion service center.
4. CAUTIONS ON INSTALLATION
●Prepare all articles necessary for
installing the main unit before starting.
●Install the unit within 35° of the horizontal
plane. (Figure 1)
Max. 35°
Figure 1
●If you have to do any modification on the
car body, such as drilling holes, consult
your car dealer beforehand.
●Use the included screws for installation.
Using other screws can cause damage.
(Figure 2)
Chassis Chassis
Damage
Max. 3 mm (M4 screw)/
Max. 8 mm (M5 screw)
Figure 2
English
NX504E/FX504E 55
Page 3
5. INSTALLING THE MAIN UNIT
This unit is designed for fixed installation in
English
the dashboard.
●When installing the main unit in NISSAN
vehicles, use the parts attached to
the unit and follow the instructions in
Figure 3.
When installing the main unit in TOYOTA
vehicles, use the parts attached to the
vehicle and follow the instructions in
Figure 4.
●Wire as shown in Section 10.
●Reassemble and secure the unit in the
dashboard and set the face panel and
center panel.
P.59
Mounting Screw Holes (Side View of
the Main Unit)
For NISSAN vehicle
❏Installing the Main Unit in a NISSAN Vehicle
Main Unit
6-Spacer (thickness: 1 mm)
56 NX504E/FX504E
For TOYOTA vehicle
Mounting bracket
(1 pair for the left and right sides)
Figure 3
6-Flat head screw
(M5 x 8)
(attached to the main unit)
Page 4
❏Installing the Main Unit in a TOYOTA Vehicle
Install by using parts attached to the vehicle. (Screws marked are attached to the vehicle.)
Main Unit
8-Hexagonal screw
(M5 x 8)
Mounting bracket
(1 pair for the left
Center Panel *1
*1 Some panel openings are too small for the unit depending on the vehicle type and model. In
such a case, trim the upper and lower sides of the panel frame by about 0.5 to 1.5 mm so the
unit can be inserted smoothly.
*2 If a hook on the installation bracket interferes with the unit, bend and flatten it with a nipper or
similar tool.
*2
Figure 4
Typical Mounting Brackets
Example 1 Example 2 Example 3
Affix the screws to the
marks.
and right sides)
❏Vehicles other than NISSAN
and TOYOTA
In some cases the center panel may require
modification. (Trimming, filing, etc.)
6. REMOVING THE MAIN UNIT
When the main unit is to be removed,
disassemble it in the reverse of the order in
“INSTALLING THE MAIN UNIT”.
P.56
7. CAUTIONS ON WIRING
●Be sure to turn the power off before
wiring.
Be particularly careful where you route
the wires.
●Keep them well away from the engine,
and exhaust pipe, etc. Heat may damage
the wires.
●If the fuse should blow, check to see if
the wiring is correct.
If a fuse is blown, replace it with a new
one of the same specification as the
original.
●To replace the fuse, remove the old fuse
of the power supply cable and insert the
new one. (Figure 5)
Fuse (15A
FUSE)
Fuse holder
Figure 5
●There are various types of fuse holder.
Do not let the battery side touch other
metal parts.
CAUTION
•After connecting the HDMI and USB
cables to the unit, use a cable tie to
tie them down. (Figure 6)
Cable tie
HDMI
Cable
Figure 6
USB Cable
English
NX504E/FX504E 57
Page 5
8. INSTALLING THE GPS ANTENNA (NX504E ONLY)
English
•Do not install the GPS antenna in a place where it may interfere with the operation
of the airbag or hinder the driver’s visual range.
•Do not use the navigation system with the GPS antenna cable cut off. The power
line in the cable may be short-circuited.
●The supplied GPS antenna is for installation inside the vehicle. Do not install it outside the
vehicle.
●Install the GPS antenna more than 50 cm away from the main unit, other audio devices
such as CD player, and a radar detector. If it is installed near these devices, GPS
reception may be impaired.
●To improve the GPS signal reception, install the GPS antenna horizontally on a flat plane.
●Do not wax or paint the cover of the GPS antenna. This may reduce the performance of
the GPS antenna.
●Install the GPS antenna at least 10 cm away from the windshield.
●Wipe off the dirt of the mounting surface before installing the GPS antenna.
●Stick the double-sided tape to the bottom face of the GPS antenna.
WARNING
●Mount the GPS antenna.
Stick it surely on a flat plane of the passenger-side dashboard where GPS signal
interruption is minimized.
●Wire the GPS antenna cable.
Fasten the cable using the Cable holders.
GPS antenna
Cable holder
58 NX504E/FX504E
Double-sided
tape
Bottom face of the GPS antenna
(Shows an example in case of the left-hand traffic.)
9. DAB ANTENNA CONNECTION (NX504E ONLY)
For details on how to attach the antenna film, refer to the installation supplied with the
antenna.
Page 6
10. WIRE CONNECTION
Yellow
White
White
Yellow
White
NX504E
DAB antenna (ZCP-133)
(sold separately)
Rear Vision
Camera
terminal
Radio
Steering wheel
remote control
terminal (sold
separately)
antenna
jack
Gray
Black
Purple
Gray
Black
Black
GPS antenna
jack
USB terminal
HDMI cable
(sold separately)
Microphone
(sold separately)
Red
Right
Left
White
Red
Right
Left
Red
Right
Left
White
Yellow
Red
Right
Left
Front
audio
output
terminal
Rear
audio
output
terminal
Subwoofer
output
terminal
(MONO 2ch)
video output
terminal
video input
terminal
audio input
terminal
HDMI/MHL
conversion adapter
HDMI conversion cable
or
Connection cable
(CCA-750)
Refer to the following
page.
Android
smartphone
Android
smartphone
External
Amplifier
Rear Monitor
iPod/iPhone
FX504E
Radio antenna jack
Steering wheel
remote control
terminal (sold
separately)
Rear Vision
Camera
terminal
Gray
Black
Black
Gray
Black
Purple
USB terminal
HDMI cable
(sold separately)
Microphone
(sold separately)
Red
Right
Left
Red
Right
Left
White
Red
Right
Left
White
Yellow
Red
Right
Left
White
Front
audio
output
terminal
Rear
audio
output
terminal
Subwoofer
output
terminal
(MONO 2ch)
video output
terminal
video input
terminal
audio input
terminal
HDMI/MHL
conversion adapter
HDMI conversion cable
or
Connection cable
(CCA-750)
Refer to the following
page.
Android
smartphone
Android
smartphone
External
Amplifier
iPod/iPhone
English
NX504E/FX504E 59
Page 7
English
Connecting the parking brake lead
Connect the lead to parking brake lamp ground in the meter panel.
●Connecting the parking brake lead to lamp ground allows you to watch video images
when the parking brake is engaged.
●When the parking brake lead is not connected, the monitor will not display video images.
No. Description
REAR RIGHT
REAR RIGHT
FRONT RIGHT
FRONT RIGHT
FRONT LEFT
FRONT LEFT
REAR LEFT
REAR LEFT
+12 V MAIN POWER (*1)
Auto antenna
ILLUMINATION
+12 V ACCESSORY (*1)
GROUND
ISO CONNECTOR
Spare terminal (Yellow)
Parking brake (Grass-green)
Remote terminal (Blue/White) (*2)
Reverse gear terminal (Purple/White)
*1 In certain vehicles - Volkswagen/Opel/Vauxhall - it is necessary to exchange the accessory
<<Red>> and the main power <<Yellow>> connection, to avoid overload and loss of memory.
*2 When the unit is installed in a 1998 or later Volkswagen model, make sure to interrupt the
<<Remote>> output. Disconnect the <<blue/white>> wire and insulate the front ends of this
cord. A breakdown may occur if the cord is not disconnected, or front ends are not insulated.
See next page for how to connect the parking brake lead.
Parking brake lamp
+
Electro-tap
Parking brake
signal lead
Parking brake lead
(Grass-green)
lead to battery
Parking brake
How to attach the electro-tap
●
1. Place the Parking brake lead at the stopper,
and fold it back in the direction of the arrow.
2. Pass the Parking brake signal lead through,
and fold it back in the direction of the arrow.
Parking brake
signal lead
Stopper
Parking brake
signal lead
Parking brake lead
(Grass-green)
❏Connecting the Accessories
Connection to the Rear Vision Camera for vehicle
The Rear Vision Camera for vehicle can be connected to optional Rear Vision Camera input
cable (CCA-644) with RCA pin cable. For detailed information, refer to the instruction sheet
or manual for the Rear Vision Camera.
●Be sure to connect the reverse gear lead to the vehicle’s relevant terminal.
●Connect the Rear Vision Camera to the RCA pin cable; if not, the screen turns black while
the gearshift lever is in the reverse gear position.
60 NX504E/FX504E
Loading...