Clarion CS150 User Manual

ongratulations on your purchase of this Ungo Convenience System. Please read this manual thoroughly to familiarize
C
yourself with your system’s components and operation. Discuss
any questions you might have with your installing dealer.
Record the serial number of your Ungo system and keep all dealer records and receipts. Be sure to discuss the installation with the dealer so that you understand the specifics of the installation in your vehicle.
CAUTIONS
USE IF THE UNGO CS150 IS THE RESPONSIBILITY OF THE OWNER.
KEEP THE REMOTE TRANSMITTERS OUT OF THE REACH OF CHILDREN.
THE UNGO CS150 IS NOT INTENDED FOR USE ON VEHICLES EQUIPPED WITH
A MANUAL TRANSMISSION.
BE SURE THE TRANSMISSION IS IN PARK BEFORE LEAVING THE VEHICLE.
TURN THE ON/OFF SWITCH TO “OFF” WHEN THE VEHICLE IS BEING
SERVICED OR PARKED IN A GARAGE.
ONLY REMOTE START THE VEHICLE IN A WELL VENTILATED AREA.
Table of Contents
1. About Your System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 1
2. Remote Transmitters
Remote Transmitter Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 2
Adding a New Transmitter into the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 2
Deleting Transmitters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 2
Battery Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 2
Additional Remote Transmitters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 3
3. Basic Features
Remote Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 3
Shut Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 3
Valet Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 4
Stop and Go . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 4
Auto Cold Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 4
4. Optional Features
Remote Keyless Entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 5
Auxiliary Function Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 5
5. Reference Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 6
6. Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 6
7. Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 7
Note: Certain features described in this manual may require additional parts and/or labor. Also, some features of
the Ungo CS150 convenience system have selectable options that must be activated or programmed during the system’s installation. These items will be identified in the following sections. Your Authorized Ungo Dealer will be happy to discuss these features with you and help you design your system to meet your needs.
About Your Ungo Convenience System
The Ungo CS150 is a remote controlled car start system. When activated, the CS150 will safely start your car by remote control, without your key in the ignition. If your vehicle is powered by a diesel engine, the CS150 will turn on the ignition for 20 seconds prior to starting the engine, in order for the glow plugs to warm up.
Once the CS150 has started the engine, it will turn on your preset accessories (heater/air conditioner) to provide you with the maximum comfort when you enter your vehicle. After activation, the CS150 will allow the vehicle to run for approximately 12 minutes (or 24 minutes if selected by your installer at the time of installation) before automatically shutting off.
Ungo CS150 System comes with:
Main Unit - The “brain” of the system.
2 - Three Button Remote Transmitters
Extended Range Receiver - Specifically designed to maximize the operating range of the Remote transmitters.
Status LED - Red illuminated indicator that provides system status information.
Valet / Service Mode Switch - used to disable the remote starting system in case the vehicle is to be serviced. Optional keyless entry features will still function.
Safety
To provide you with the maximum safety and reliability, the CS150 incorporates the following safety features:
Brake Pedal Shutdown - Shuts down the CS150 when the brake pedal is pressed.
Hood Pin Switch Protection (optional) - Prevents the engine from being started while the hood is open.
Valet Mode - Prevents the vehicle from being started when being serviced.
Options
The CS150 Remote Start system also has the capability of controlling the following optional convenience features:
Remote Keyless Entry (Door Lock/Unlock)
Remote Trunk Release
Window Roll-up
CS150 Owner’s Manual - Page 1
Remote Transmitters
Remote Transmitter Layout
Button 1 Button 3
The Ungo CS150 comes with 2 Remote Transmitters used to control the system’s features. Each time a transmitter button is pressed, the LED will flash to indicate that a transmission is taking place.
Button 1 Locks and Unlocks the doors*. Button 2 activates the system’s auxiliary function (usually used for optional trunk release)*. Button 3 is used to Remote Start the vehicle. It is also used to shutdown the engine if remote
started.
*optional features
LED Button 2
Adding or Deleting Remote Transmitters
The Ungo CS150 has the ability to recognize 2 individual remote transmitters. If the vehicle is used by multiple drivers, each can have their own Remote Transmitter.
To add a Remote Transmitter:
1. Turn the ignition on, off, on, off, on within 4 seconds.
• The status LED and parking lights will flash once.
2. Press and hold the Valet switch for 2-3 seconds.
• The status LED and parking lights will flash 3 times.
3. Release the program switch.
4. Press Button 3* on each Remote Transmitter.
5. Turn off the ignition.
*Be sure that you press only Button 3. Pressing any other transmitter button will cause the unit to recognize the individual transmitter buttons incorrectly.
Note: The CS150 will respond to only those remote transmitters learned during this procedure. Any previous remotes will be deleted.
Battery Replacement
Your Ungo Remote Transmitter uses a 12 volt alkaline battery, which will need to be replaced from time to time. Under normal conditions, the battery should last for up to a year before it needs replacement.
Page 2 - CS150 Owner’s Manual
When your Remote Transmitter’s battery is in need of replacement, you will notice a decrease in your system’s operating range or a decrease in the brightness of the Transmitter’s LED indicator .
To change the battery, remove the 2 screws at the back of the Transmitter and carefully separate the top and bottom halves of the Transmitter case.
Insert the new battery, making sure that the positive and negative terminals are positioned correctly and replace the cover.
Battery Type: 23A
Additional Remote Transmitters
Additional Remote Transmitters for your CS150 are available from your Authorized Ungo dealer.
Basic Features
Remote Starting
To Remote Start the System:
1. Be sure the System is not in Valet Mode.
2. Press Button 1.
• The parking lights will turn on.
• The LED will flash rapidly.
• The engine will start and run for the duration of its programmed Run Timer.*
• The heater or air conditioner will turn on (if turned on prior to exiting the vehicle).
Turning on the ignition key then pressing the brake pedal will disengage the CS150 and allow you to operate and drive your vehicle in a normal manner.
*If the engine fails to start on the first attempt, it will repeat the starting procedure 2 more times. If the vehicle fails to start after a total of 3 times the parking lights will flash 4 times and the doors will lock (if installed).
Shut Down
The following will shut down the engine when it is under Remote Start control:
1. Pressing Button 1.
• After the engine shuts down the doors will lock (if installed).
2. Pressing the Brake Pedal.
3. Opening the Hood.
4. Remote Start Time-Out (completion of the timed run cycle).
CS150 Owner’s Manual - Page 3
Valet Mode
Allows you to temporarily disable the remote starting feature when the car is being serviced or turned over to a parking attendant.
To turn Valet Mode on:
1. Turn on the ignition.
2. Within 5 seconds, press and hold the Valet button for 3 seconds.
• The LED will turn on solid.
• The parking lights will flash once.
To turn Valet Mode off:
1. Turn on the ignition.
2. Within 5 seconds, press and hold the Valet button for 3 seconds.
• The LED will turn off.
• The parking lights will flash twice.
While Valet Mode is on, you can continue to lock and unlock the doors with the Remote Transmitters, as well as operate the optional Auxiliary Function.
Stop and Go
The Stop and Go Feature allows you to remove the ignition key and exit the vehicle while keeping the engine running during short stops.
To leave the vehicle running:
1. Press the Brake Pedal and hold.
2. While pressing the Brake Pedal, push Button 1 on the Remote Transmitter.
• The LED will flash rapidly.
• The parking lights will flash four times.
3. Release the Brake Pedal.
4. Remove the key from the ignition switch.
5. You may now exit the vehicle and lock the doors manually or using the Remote Transmitter
To re-enter the vehicle and resume driver control:
1. Unlock the doors manually or by pressing Button 1 on the Remote Transmitter*.
2. Turn on the ignition .
3. Press the Brake Pedal to disengaged the CS150.
• The LED will turn off.
*If optional keyless entry feature is installed.
Auto Cold Starting
The Auto Cold Starting Feature allows the vehicle to automatically start the vehicle every two hours and run for the preset Run Time.
To turn on Auto Cold Starting:
1. Press and hold Button 1 for 5 seconds.
• The parking lights will flash 5 times.
• The engine will start and run for 30 seconds.
• The LED will emit double flashes.
Page 4 - CS150 Owner’s Manual
CS150 Owner’s Manual - Page 4
To turn off Auto Cold Starting:
1. Press and hold Button 1 for 5 seconds.
• The parking lights will flash 10 times.
• The LED will stop flashing.
Note: Pressing the brake pedal will also turn off the Auto Cold Starting feature.
Optional Features
Remote Keyless Entry
To Lock and Unlock the doors:
1. Press Button 1 on the Remote Transmitter.
• The parking lights will flash once.
• The doors will lock.
• The LED will begin flashing slowly*.
2. Press Button 1 again on the Remote Transmitter.
• The parking lights will flash twice.
• The doors will unlock.
• The LED will stop flashing*.
*If the Auto Cold Starting feature is activated, the LED will emit double flashes.
Auxiliary Function Output
The system is equipped with an Auxiliary Function output that can be used to remotely control an optional feature such as, electric trunk release, remote car starter, power windows, power sunroof, garage door receiver, etc.
To operate the Auxiliary Function, press and hold Button 3 for two seconds.
This function will operate regardless of whether the system is locked or unlocked.
Reference Chart
You can use this chart to quickly identify and interpret the CS150’s parking light and LED indications.
Flashes Functions
Slow Doors are locked (optional) Rapid Remote Started/Running Double Valet mode Solid Auto Cold Starting engaged
Flashes Functions
1 Doors are locked (optional) 2 Doors are unlocked (optional) 4 Unable to Remote Start vehicle 5 Auto Cold Starting engaged 10 Auto Cold Starting disengaged
Status LED Indications
Parking Light Indications
CS150 Owner’s Manual - Page 5
Technical Data
Specifications
Main Unit
Voltage: 12v, negative ground Current Consumption: <15mA
Temperature Range: -40oF to +257oF
Auxiliary Output Capability: 500mA Internal Relays: (4) 30A, (1) 15A
Transmitter
Current Consumption: <.00mA, standby Battery Type: miniature 12v, type 23A
-40oC to +125oC
FCC ID:
J5523518 T1 J5523518 R1
T
HIS DEVICE COMPLIES WITH FCC RULES PART 15.
OPERATION IS SUBJECT TO THE FOLLOWING TWO
CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND INTERFERENCE THAT MAY BE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
(2) THIS DEVICE MUST ACCEPT ANY
Ungo Security Corporation
Gardena, CA
USA
Page 6 - CS150 Owner’s Manual
Warranty Information
Model No.: CS150
Serial No.:
Dealer Name:
Address:
Purchase Date:
Warranty Information
1. Ungo Security Corporation of Gardena, California ("Ungo
Security") warrants this Ungo system to be free from defects in materials and workmanship and to comply with Ungo Security’s applicable printed specifications.
2. Ungo Security systems carry a limited lifetime warranty
on the Main unit (system brain) and transmitters. The warranty is limited to Ungo Security systems that have been installed by an approved Ungo dealer and is extended to the Original Purchaser ("Owner") and to the original vehicle in which it was installed only, and is not transferable to any subsequent owner or owners of the product(s). All other products (including those products of other manufacturers which are supplied by Ungo Security as a part of, or an accessory to, an Ungo Security-manufactured product) are warranted by Ungo Security for a period of one year from the date of sale to the Owner. For specific identification of such products contact Ungo Security.
3. This warranty shall not cover: (I) any damage caused by
Owner’s negligence or misuse of any kind, or any damage due to causes unrelated to Ungo Security’s manufacturing, including, but not limited to improper servicing or repair by someone other than Ungo Security or an authorized service facility: (II) alterations or modifications to the Ungo system other than the addition of an authorized accessory: or (III) improper installation or removal from the vehicle contrary to Ungo Security’s instructions.
4. Obligations of Ungo Security. In the event the Owner’s
Ungo system does not comply with this warranty, it must be returned to Ungo Security as specified below. Ungo Security will repair or replace it with a new or reworked unit, within thirty (30) days of receipt and acceptance of such defective unit, and without cost to Owner.
5. To make a claim under the warranty. Owner must: (I)
provide Ungo Security with written notice that the Ungo System does not comply with the warranty within thirty (30) days from the date of the Owner’s discovery of the defect and (II) furnish proof of purchase and purchase date (this requirement is satisfied if Ungo Security has a completed warranty registration card on file).
6. Owner obligations. To obtain Warranty Service, Owner
must at Owner’s expense: (I) have the Ungo system removed from the vehicle by an authorized Ungo Security dealer, (II) package the unit in a reasonable manner to prevent damage to the unit during shipment; and (III) ship the unit, freight prepaid, to Ungo Security’s factory or other authorized repair facility.
7. Repair facility locations. To obtain the name, address
and phone number of the nearest Authorized Ungo Repair Facility, Owners may contact Ungo Security at 310-327-
9100.
8. The Owners of Ungo systems in California have the right
to have the product serviced or repaired during the warranty period. The warranty period will be extended for the number
of full days that the product has been out of the Owner’s hands for warranty repairs. If a defect exists within the warranty period, the warranty will not expire until the defect has been fixed. The warranty period will also be extended if the repair has not been performed due to delays caused by circumstances beyond the control of the Owner, or if the warranty repairs did not remedy the defect and the Owner notifies Ungo Security or the seller of the failure of the repairs within sixty (60) days after they were completed. If, after a reasonable number of attempts, the defect has not been fixed the Owner may return this product for replacement or a refund, subject in either case, to a deduction of a reasonable charge for usage. The time extension does not effect the protection or remedies the Owner has under other laws.
9. Exclusions from liability. (A) In no event shall Ungo Security be liable for any loss or
damages beyond the original purchase price of the Ungo system , and Ungo Security specifically excludes any and all incidental and consequential damages, whether resulting from breach of warranty or contract, negligence or other conduct in connection with any sale, use, servicing or repair of a unit. (Some states do not allow the exclusion of incidental or consequential damages, so the above exclusion may not apply to you.)
(B) There are no warranties, express, statutory or implied, which extend beyond that which is described herein, and in particular, all implied warranties of merchantability and fitness for a particular purpose, and all warranties of title and against encumbrances, are expressly disclaimed, limited and excluded as permitted by law; but in no event shall any implied warranty, whether of merchantability of fitness for a particular purpose or otherwise, have a duration exceeding that of the express warranty made herein. (Some states do not allow limitation on how long an implied warranty lasts, so the above limitation may not apply to you.)
(C) No agent, officer, employee or representative of Ungo Security, or any other person, has authority to make any representations, promises or warranties respecting Ungo systems and their authorized accessories.
(D) Owner has the right to bring any action at law or in equity to resolve disputes concerning, or to enforce, the provisions of this warranty. No action at law or in equity may be brought against Ungo Security for breach of warranty or contract or based on negligence of other conduct more than three (3) years from the date the cause of action has occurred.
(E) This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
(F) The remedies extended herein are the sole and exclusive remedies available to Owners of Ungo systems.
(G) Under no circumstances should this warranty, or the products covered by it, be construed as an insurance policy against loss.
CS150 Owner’s Manual - Page 7
Ungo Security Corporation
A Clarion Company
661 West Redondo Beach Blvd.
Gardena, CA 90247
800-Go-Clarion
© Ungo Security Corporation, Gardena, CA 97-CS150-10 Rev. 1 (7/99)
www.clarionmultimedia.com
Loading...