Page 1
Page 2
English
Contents
1. Before Use................................................... 3
2. Features ...................................................... 3
3. Names of the Buttons .................................. 4
4. Operations ................................................... 4
5. Connections................................................. 7
6. Installation ................................................... 8
7. Troubleshooting........................................... 9
8. Specifications .............................................. 9
This unit has been tested and found to
comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC
Rules.
These limits are designed to provide
reasonable protection against harmful
interference in a residential installation.
This unit generates, uses, and can
radiate radio frequency energy, and, if not
installed and used in accordance with the
instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
2
installation.
If this unit does cause harmful
interference to radio or television
reception, which can be determined by
turning the equipment off and on, the user
is encouraged to consult the dealer or an
experienced radio/TV technician for help.
INFORMATION FOR USERS:
CHANGES OR MODIFICATIONS TO THIS
PRODUCT NOT APPROVED BY THE
MANUFACTURER WILL VOID THE
WARRANTY AND WILL VIOLATE FCC
APPROVAL.
Page 3
1. Before Use
Warning
• Do Not Back Up Vehicle While Relying Only on the Monitor Image
• Use Slow Speeds When Backing Up
• The rear-view monitor image has the same right-left inversion as your vehicle’s
rearview mirrors. Depending on the vehicle, the field and angle of view may differ.
Precautions (when you use the monitor)
z Do not touch the LCD panel.
z Use the product at the temperature range of -10°C ~ 60°C.
z Screen may be a little dark when the product is operated in low temperature areas.
Screen will show normal luminosity after a few minutes.
z Do not disassemble and modify the product in any way.
This may cause fire and/or electric shock.
z When you install the product in a car and watch monitor, the car engine should be
running as there might occur excessive discharge of the car battery.
z Any liquid leaking into product may cause malfunction.
Precautions (when you use the product in a car)
z The driver should not use the product while he/she is driving.
z Be cautious of humidity and shock when you use the product in a car.
z Cover the product when exposed to direct rays of the sun for a long period of
time.
(You should keep the product at a temperature range of -20°C ~ 70°C.)
English
2. Features
z Application of 5.6" TFT LCD with high resolution and low reflection
z All functions are displayed on screen (OSD function)
z 7 Language Display Selection
(ENGLISH-DEUTSCH-ITALIANO-FRANÇAIS-ESPAñON- - )
z Free voltage (From DC12V to DC24V)
z Dimmer selection function
z Picture quality control (PWM control)
z Camera input (2 system)/Work together with back gear/turn signal
3
Page 4
English
3. Names of the Buttons
[POWER]
[MODE]
[MENU]
[UP]
[DOWN]
STAND BY LED
4. Operations
1
POWER
ON OFF
2
MODE (Camera Selection)
It is a function to change CAMERA (CAM1/CAM2).
CAM1
(1) Press [POWER] button to on the power.
(STAND BY state is OFF)
(2) Press [POWER] button again to off the
power.
(STAND BY state is ON)
(1) Press [MODE] button.
(2) CAM1 or CAM2 appears on the screen
and it disappears after 5 seconds.
CAM1 CAM2
Note: In the mirror mode, the character is
inverted.
4
Page 5
3
MENU
It is a function to select MAIN MENU (SETUP, PICTURE CAMERA)
(1) Press [MENU] button to select MAIN MENU, changed color in red when it is selected.
• Every time the button is pressed, the setting changes.
English
SETUP
PICTURE
CAMERA
(2) Press [MODE] button to select SUB MENU, changed color in red when it is selected.
• Every time the button is pressed, the setting changes.
z SETUP z PICTURE
DIMMER
LANGUAGE
DIRECTION
RESET
SUB MENU
ENGLISH
0
CONTRAST
BRIGHTNESS
COLOR
TINT
50
70
50
50
z CAMERA
CAM1
CAM2
NORMAL
NORMAL
SET UP (SUB MENU)
(3) Press [UP]/[DOWN] button to change Settings.
z DIMMER
–
z LANGUAGE
ENGLISH
– – – – –
DEUTSCH
ITALIANO
–
FRANÇAIS
ESPAñON
5
Page 6
English
z DIRECTION (Inverted upside down)
180
ENGLISH
DIMMER
LANGUAGE
DIRECTION
RESET
ENGLISH
0
z RESET X
A factory default reset will clear all of OSD information
PICTURE (SUB MENU)
(3) Press [UP]/[DOWN] button to change Settings.
z CONTRAST z BRIGHTNESS z COLOR
RESET
DIRECTION
LANGUAGE
DIMMER
CONTRAST
BRIGHTNESS
COLOR
TINT
70
40
40
40
CONTRAST
BRIGHTNESS
COLOR
TINT
40
70
40
40
z TINT
CONTRAST
BRIGHTNESS
COLOR
TINT
40
40
40
50
CAMERA (SUB MENU)
(3) Press [UP]/[DOWN] button to change Settings.
z In the mirror mode, the screen is inverted laterally.
CAM1
CAM2 NORMAL
NORMAL
CONTRAST
BRIGHTNESS
COLOR
TINT
40
40
70
40
6
Page 7
5. Connections
English
GREEN
(CAMERA2)
BLACK
(CAMERA1)
BLACK
GROUND
RED
POWER
DC12V
~24V
*3
CAMERA2
*2
*1
*2
*3
BLACK (CAMERA-1, priority) Standby + (for rear-view)
Connect this cable to “+” of back gear lamp.
GREEN (CAMERA-2) Standby + (for side-view)
Connect this cable to “+” of turn signal lamp.
*3
CAMERA1
*2
CAMERA1
(Sold Separately)
*1
CAMERA2
(Sold Separately)
*1
Use a Clarion camera.
A relay cable, sold separately, is required
for connecting the camera.
Use tape to keep the connection between
the monitor cable and the camera relay
cable secure.
7
Page 8
English
6. Installation
1. Choose a location where you install the Monitor. Clean the place for the Stand with cleanser
and remove the Protective Tape. And then attach it exactly where you want.
2. Fasten the Monitor with Tapping Screw.
3. Adjust angle of Stand and install Monitor.
4. Connect each connecting cable as in the product installation reference.
Cable Guidance
Fix Knob
(Bracket)
Tapping Screw
Stand Base
Control Knob
(Angle)
Safeguard tape
Monitor Cable Connection
* Installed on the ceiling * Normal Installation
8
Page 9
7. Troubleshooting
Problem Cause Measure
No image is displayed.
Power does not turn on.
Color is washed-out.
Is camera connected
properly?
Is power cable
connected properly?
Is a fuse blown out?
Operating
environment is
inappropriate.
Check the wiring to the camera and the
camera connection.
Check the wiring.
Replace with a fuse of the same amperage
(2A).
Temperature in the car is below 0°C or over
60°C. Check to see that the temperature in
the car is appropriate (around 25°C).
8. Specifications
English
ITEM
SCREEN SIZE 5.6 INCH (14.22cm)
NUMBER OF PIXELS 320(W) x 3(RGB) x 234(H)
DOT PITCH 0.118(W) x 0.362(H) mm
PAN EL
POWER SUPPLY
REAR INPUT POWER DC 12V - 24V
INPUT SYSTEM AUTO (NTSC/PAL)
FREQUENCY
OSD DISPLAY 7 LANGUAGE
USER CONTROLS POWER, MODE, MENU, UP, DOWN
OPERATING TEMPERATURE -10°C ~ + 60°C
STORAGE TEMPERATURE -20°C ~ + 70°C
DIMENSION (W x H x D) 163(W) x 112(H) x 30(D)
WEIGHT 0.3Kg
ACCESSORIES
BRIGHTNESS
DISPLAY AREA 113.28(W) x 84.7(H) mm
CONTRAST RATIO 300:1
VIEW ANGLE (H/U/D) 65deg / 45deg / 65deg
VOLTAGE DC 12V - 24V
CURRENT 550mA (DC 12V, MONITOR SET ONLY)
HORIZONTAL 15.734 KHz 15.625 KHz
VERTICAL 60Hz 50Hz
350 cd/m
MONITOR CABLE ASS’Y····································· 1
STAND ASS’Y·······················································1
SPECIFICATION
NTSC PAL
2
Caution: The design and specifications of this product in order to improve its quality may be changed without notice.
9
Page 10
2007/2
Clarion Co., Ltd.
All Rights Reserved. Copyright 2007: Clarion Co., Ltd.
Printed in Korea / Gedruckt in Korea / Stampato in Corea /
Imprimé en Corée / Impreso en Corea
CJ-5600E
Loading...