ArtSeries Amplifiers
Owner's Manual
A100.
2
/ A200.
A600.
A204.
2
2
/ A1200.
2
/ A404.
/ A300.
2
2
2
7402 W. Detroit Street Suite 180
Chandler, AZ 85226
1-800-62-POWER
Designed and Handcrafted in the USA
p
Mobile Audio Electronics
CONGRATULATIONS AND THANK YOU
PrecisionPower, Inc. high performance mobile audio amplifier.
PrecisionPower is proud to be a world leader specializing in the
design, engineering, and manufacture of "State of the Art" mobile
audio electronics. Our success is derived from the fact that we do not
incorporate gadgets or passing fads into our products. Sound
engineering practice, combined with deceptively simple yet highly
effective circuit designs, characterize every PPI product. Yet, our
demand for maximum value dictates that every ounce of fat be
trimmed if it does not contribute to sound quality or reliability. This is
why PPI products have consistently enjoyed an unparalleled
reputation for sound value. We are sure that your new Art Series
amplifier will provide you the "State of the Art" in mobile audio
lification.
am
foryourchoiceofa
Important Safeguards
p
A
A
A
20
The following list of 'Important Safeguards has been compiled to help you achieve optimum satisfaction and
the highest quality performance from your new mobile audio amplifier. Please take the time to review these
safeguards before operation and or installation of your new Art Series amplifier.
Read Instructions
Table of Contents
Glossary of Terms 4
We all have a tendency to read instructions only after something doesn't work as anticipated. This manual
rovides specific information concerning the operation and installation of your new amplifier. Please read
this manual thoroughly and retain it for future reference.
Keep Your Sales Receipt
Your PPI amplifier has a three-year limited warranty when it is installed by an Authorized PPI dealer. Non-
uthorized dealer installed (PPI) amplifiers carry a one-year parts / ninety days labor limited warranty. To
establish the starting date of warranty coverage, a copy of your sales receipt must accompany your amplifier
for all warranty service. Please file your sales receipt away for future reference. For your convenience, a
complete limited warranty statement is located at the back of this manual.
Follow Instructions
ll use and installation instructions should be followed to assure proper operation of your new Art Series
amplifier.
Heed All Wiring Requirements
high-performance amplifier requires minimum wire gauges be used for the Power, Ground, Remote TumOn, and Speaker cables. To assure proper operation of your Art Series amplifier, following all wiring
requirements.
Heed all Fusing Requirements
The fusing requirements of your Art Series amplifier have been established for its continued safe operation.
Replacement with a higher value fuse may result in damage and voiding of warranty.
Installation Accessories
The Art Series amplifiers will require non-supplied installation accessories. Please refer to the Installation
Section of this manual for a list of requirements or consult your Authorized PPI dealer before installation.
Water and Moisture
Features 5
Specifications 6
About Your Art Series Amplifier 7
Installation 11
System Tuning 15
Troubleshooting 17
System Designs 18
Limited Warranty
Never mount your Art Series amplifier in a location which would subject it to immersion or exposure to water.
Servicing
Do not attempt to service this amplifier yourself. Opening or removing covers will void your warranty. For
service information, consult your Authorized PPI dealer or call Precision
Our customer service representatives are available Monday through Friday from 8am to 5pm Mountain
Standard Time.
Caution!
The use of a high-powered audio system may cause hearing loss or damage. While PPI
systems are capable of "Concert level" volumes with incredible accuracy, they are
designed for you to enjoy the subtleties created by musicians while listening at
reasonable sound pressure levels. The use of a high powered audio system may impair
your ability to hear traffic sounds, and therefore, may constitute a traffic hazard. We
advise lower volume levels while driving.
Power
,Inc.at1-800-62-POWER.
PPI
Glossary
Remote Turn-
On:
Low current automatic switching circuit that turns the amplifier
on and off. Typically connected to the remote antenna or amp
turn
-
on lead of most car radios, cassette, or CD players.
Features
The following terms are used in this manual. Since they may be unfamiliar, the
following definitions are provided.
AM II
Bridging:
Gain:
L.E.D.:
Load Impedance:
Mixed Mono:
PWM
Adaptive MOSFET II is an advanced protection circuit
designed to prevent amplifier shut-off due to low load imped
ance. AM III optimizes output power to maintain uninterrupted
operation whenever the amplifier senses a load impedance of
less than two Ohms. An L. E. D. signals when AM II is working.
Combining two amplifier channels into one channel, typically
used to create a mono output.
The ratio of output voltage to input voltage. The gain control
allows adjustment to the amplifier's output level for varying
input levels.
Light Emitting Diode. Indicates power on / off and when AM
is working.
Measurement of speaker(s) resistance / reactance that the
amplifier must drive.
The amplifier's ability to play the Left and Right Stereo channels
while playing a third (bridged) mono channel.
Pulse-Width Modulated power supply. Our PWM maintains a
regulated output voltage and a high conversion efficiency over
the input supply range of 11 - 15 VDC. The result is less demand
on the battery, lower (amplifier) operating temperature, and
extremely accurate low frequency reproduction.
-
II
A100.2 / A200.2 / A300.2
A600.2 / A1200.2 / A404.2 / A204.2
Pulse-Width Modulated (PWM) Switching Power Supply for High-Efficiency
Regulated Power Supply Provides Full Rated Power from 11 - 15 VDC
Discrete Power Amp Circuitry
Internally Bridgeable
Mixed Stereo / Mono Operation
Output Short Circuit Protection
Differential Input Stage
Low Impedance Protection with Diagnostic L.E.D.
Adjustable Input Sensitivity
Gold RCA Input Connectors
PPI's Exclusive Wire Connection System
Liquid Cooling (Optional)
Amplifier Control Module Compatible (Optional ACM-420)
Three Year Limited Warranty
ACM
Amplifier Control Module. Our ACM-420 (optional) controls up
to ten PPI amplifiers for synchronized system start and "noise
gate" functions to inhibit background noise when no music
signal is present
Designed and Handcrafted in the USA
Technical Specifications
A100.
2
Continuous Power Output per Channel:
25 Watts
50 Watts
100 Watts
20 Amp
2x9.25x6”
6lbs.
A
A
A
A
p
p
Art Series Model:
4 Ohms, 11-15 VDC, Stereo:
2 Ohms, 11-15 VDC, Stereo:
4 Ohms, 11-15 VDC,
Power Fuse:
Dimensions (inches):
Shipping Weight:
4-Channel Model: A204.2 A404.2
Continuous Power Output per Channel,x4Stereo,x2Bridged
4 Ohms, 11-15 VDC, Stereo: 25 Watts 50 Watts
2 Ohms, 11-15 VDC, Stereo: 50 Watts 100 Watts
Bridged:
A200.
2
A300.
2
A600.
2
A1200.
50 Watts 75 Watts 150 Watts 300 Watts
100 Watts 150 Watts 300 Watts 600 Watts
200 Watts 300 Watts 600 Watts 1200 Watts
20 Amp 30 Amp 40 Amp 100 Amp
2x9.25x8.5” 2x9.25x10.6”
7lbs. 8lbs. 9lbs. 14lbs.
2x9.25x14”
2x9.25x24"
About your New Art Series Amplifier
s a world leader in the design and manufacture of high-performance mobile amplifiers,
2
PrecisionPower, Inc.'s commitment to being: “Absolutely Start of the Art” demands that
we create products that offer high reliability and superior sound quality. To do this, we
must recognize and find solutions to the unique problems, which affect the performance
of electronics in the mobile environment.
t PPI, we build upon experience. We currently design and manufacture over 20
different amplifiers. Each is designed to be application specific, either in rated power,
number of channels, or with i ntegrated accessories. This large reservoir of knowledge
has provided us with the innovative design solutions incorporated in the Art Series
mplifiers.
s you review this section, keep in mind that the new features found in the Art Series
amplifiers directly influence their performance and, therefore, must be understood before
operation and / or installation. Please take a few minutes to review the following
information. The user benefit and operational parameters of the 'key' design features are
detailed below.
Pulse- Width Modulated (PWM) Switching Power Supply
4 Ohms, 11-15 VDC, Bridged: 100 Watts 200 Watts
Power Fuse: 20 Amp 50 Amp
Dimensions (inches): 2x9.25x10" 2x9.25x13"
Shipping Weight: 7.5 lbs. 8.5 lbs.
Common Specifications:
Power Bandwidth: 10 Hz -50 kHz
Total Harmonic Distortion: .02%
Input Sensitivity: .2 - 2.5 V
Input Impedance: 10k Ohms
Load Impedance (Stereo): 2 - 8 Ohms
Load Impedance (Bridged): 4 - 8 Ohms
Supply Voltage: 11 - 15 Volts
The voltage supplied by an automobile's electrical system will vary depending upon the
number of accessories you are using. As you turn on / off various accessories (headlights, air conditioner, rear window defroster, power windows, etc) the voltage that your
car's electrical system is providing will change according to the demand. The Art Series
fully regulated power supply guarantees rated spec over a wide range of voltages (11
VDC to 15 VDC).
Our PWM supply offers high-efficiency. This efficiency translates into cooler operation.
The hostile environment of mobile audio presents a real problem for an amplifier to
operate properly. When an amplifier is running, it develops heat It is the job of the
heatsink to pull this heat away from the internal components. If the heatsink gets too hot,
the amplifier will modify its operation to protect itself from damage. The amplifier's ability
to maintain a proper operating temperature is oftentimes aggravated by the conditions
(ambient air temperature, mounting location, playing level, duration of operation, as well
as the load impedance) presented by the auto-sound environment. The Art Series PWM
ower supply's high-efficiency means lower operating temperatures and a higher
tolerance for thermal control. The temperature protection circuit will engage at 75
degrees Celsius.
Heatsink Design
To understand why PPI created this unique heatsink design, it's important to understand
what purpose a heatsink serves and how it works.
When an amplifier operates, the internal components develop heat. This heat must be
transferred away from the components for them to operate properly. By securing the
com
onents to the underside of the heatsink, theprocess of conduction transfers
the heat from the components to the heatsink. The heatsink, in turn, must dissipate this
p
heat or become too hot for the internal components to operate properly. The heat can be
transferred from the heatsink by three different processes: Conduction, Radiation, or
Convection.
Conduction is defined as the process by which heat is transferred through matter,
without transfer of the matter itself A practical example of this would be the cooling
system in your car which circulates a liquid (matter) in order to transfer the heat away
from your engine.
In the mobile environment, conduction is not the primary process of transferring heat
from the heatsink. The use of a circulating liquid or gas is impractical, unless specific
rovisions were made in the design of a heatsink to accomodate this type of transfer.
There is nothing in the vehicle which could easily be used to heatsink the heatsink. Air is
the only (practical) conductive (heat transfer) medium involved when you install an
amplifier in your car. As we will discuss later, heat radiated by the heatsink is conducted
out into the environment, triggering the process of convection.
Engineers have recognized the importance of radiant surface area, but the constraints of
the automotive environment have forced heatsink designs to remain compact. In order to
improve radiating efficiency, designers have simply added more fins. With limited space,
adding more fins means that they get closer together What PPI's engineers observed
was that fins in close proximity radiate heat from fin to fin rather than into the
environment. If convection is not available to draw the heat out from between the fins,
the heat becomes trapped, causing a reduction in radiant heat transfer efficiency.
The Art Series heatsink addresses this problem and improves radiant heat transfer
efficiency by providing more effective radiating surface area. Combined with our highly
efficient (less wasted energy in the form of heat) PWM power supply, the result is an
amplifier with improved thermal capabilities.
As with any amplifier, care must be taken when selecting a mounting location. There
must be two inches of air space around the heatsink for proper heat dissipation to take
place. If mounting in an enclosed area, a fan may be added to improve heat transfer.
RefertotheSectiononInstallationformoreinformation.
Radiation is defined as the process of giving out light, heat, or other radiant energy. An
example of this process would be the sun. It radiates heat, light, and other radiant
energy.
Radiation is the primary process of heat transfer for a heatsink. As the conducted heat
builds (from the internal components), it radiates from the surface out into the
surrounding environment. The amount of heat radiated by the heatsink is determined by
its surface area. The traditional way to add surface area is to use fins, expanding the
radiating surface without increasing the overall dimensions of the amplifier.
So why doesn't the Art Series heatsink employ the traditional use of fins since it must
adhere to the same rules of thermodynamics that all other heatsinks do? We must
discuss the third process - convection before the answer will become clear.
Convection is defined as the transfer of heat from one place to another by the movement
of heated particles of a gas or liquid. An example of this process would be warming your
hand by holding it in the hot air rising from an oven.
When an amplifier's heatsink becomes warm, it conducts heat out into the surrounding
environment, warming the air. The warm air begins to rise, creating air currents which
draw heat away from the heatsink. With a traditional finned heatsink, this process is
most effective when the amplifier is mounted on its vertical axis. As with chimney, the air
circulates upward, over the fins, improving the heat transfer process.
Your ability to take advantage of convection is limited by the installation constraints
imposed by the mobile environment. Mounting an amplifier on the vertical axis is not
always possible and generally, not preferred (by the consumer). The amplifier's heatsink
is left with only one primary process for heat transfer - radiation.
Central Muting and the ACM-420
One of the accessories that we at PPI offer the discerning audiophile is the amplifier
control module (ACM), commonly known as a "noise gate". The ACM eliminates
annoying and possibly damaging start-up noise (such as "clicks" and "pops") by
sensing signal voltage changes and blocking the signal when there is no music present, such as between CD tracks. We highly recommend the addition of an ACM 420 to any high performance audio system.
The addition of central muting to the ArtSeries amplifiers allows muting to be controlled throughout the system by the ACM. Upon system start, the muting feature is
activated. After a set time interval, the muting is turned off.
The power L.E.D. at the front of the amplifier also shows whether or not the system
is muted. When the amplifier is activated, the power lamp will be red to indicate muting. After the muting is turned off, the lamp will turn green to indicate normal operation.
If an external ACM is added to the system, the ACM remote output signal can be
connected to the amplifier remote to mute the system during periods of low or no
signal to inhibit background noise. The ACM-420 may be installed to control up to
ten PPI amplifiers, offering the additional benefit of synchronized system restart.
AM III Protection Circuitry
All ArtSeries amplifiers utilize a highly-efficient, Pluse-Width Modulated power supply. This means the amplifier will continue to oeprate within regulation until the battery voltage drops below 11 volts or the heatsink temperature reaches 70 degrees
Celsius (158 degrees Fahrenheit). This new power supply also incorporates the second generation of PPI's Adaptive MOSFET protection circuitry.
The advanced protection circuit
was developed to prevent shut-
Watts
100
off due to the fluctuating impedance loads presented by today's
complex speaker systems. The
adaptive circuit optimizes output
50
power to maintain uninterrupted
operation whenever the amplifier senses an impedance load of
25
less than 2 ohms. A low impedance indicator (Diagnostic
L.E.D. ) is provided to let you
know when the amplifier is operating in this mode. It is important
84210.5
Figure A: AM II Protection Circuitry
Output Power vs. Impedance
Ohms
to note that there is no increase in output power below the 2 Ohm threshold.
Maximum power is achieved at 2 Ohms. AM III provides you the satisfaction of knowing that your ArtSeries amplifier will continue to play when momentary impedance
dips occur. (Refer to figure A)
In the case of a short circuit, AM III will engage to protect the shorted channel but will
continue to play the unaffected channel. When this occurs, audible distortion will be
heard. Turn off the system and repair this short. Once the problem has been
repaired, the amplifier will return to normal operation.
Differential Inputs
The ArtSeries amplifiers are capable of operation into a two Ohm load in a stereo
configuration and a four Ohm load in a bridge mono configuration. However, for
optimum performance a four Ohm load in stereo and an eight Ohm load in mono are
recommended. Refer to the Section on System Design for more information.
PPI's Exclusive Wire Connection System
Over the years, advances in mobile audio electronics have changed the demands
placed on the type and size of wire needed to create a high-performance mobile audio
system. To meet this need,
PPI
has created an exclusive wire connection system. This
unique, removable connection system offers the versatility of terminal strips, the
convenience of quick connect / disconnect style connectors, and the reliability afforded
by direct connection to the circuit board. The power and ground connector will accept
cable up to 6 gauge in size. The speaker/ remote tum-on connector will accept cables up
to 10 gauge in size. Refer to the Section on Installation for more information.
Fusing
The Art Series amplifier is protected from current over-load situations by a blade fuse
(Maxi - Fuse ). This type of fuse has a number of advantages. First it's available in
higher values, and its single element design is more effective than using two fuses of
lower value. Second, we could board mount it. This eliminates the use of ‘jumperwires’
(from the end-panel to the circuit board) which improves reliability. Finally, they are
readily available from any auto-supply store and are easy to service. The A100 & A200
use a 20 Amp fuse, the A300 - a 30 Amp fuse, the A600 - a 50 Amp fuse and the A1200
-2-60Ampfuses.
One of the obstacles that must be overcome when designing a mobile audio system
is that of external interference caused by alternators, generators, and other electrical
subsystems. In other amplifiers, all input grounds are wired directly into the speaker
ground, as shown in Figure B. The ArtSeries amplifiers, on the other hand, have isolation resistors between the input grounds and the speaker ground. This helps to prevent alternator noise from interfering with the signal between this unit and any prior
"upstream" units.
Discrete Power Amp Circuitry
Exclusive use of discrete output transistors
results in increased sonic transparency,
outstanding dynamic range, and high
instantaneous current capability. We've
designed the power bandwidth to be from
10Hz to 50,000Hz +/- 1dB. This ability to
produce full power with linear frequency
response well beyond the threshold of
human hearing insures that the amplifier's
performance over the musical spectrum
will be flawless.
For safety reasons,
PPI
recommends that the power cable be fused at the positive
terminal of the battery. If this fuse (not-supplied) is not installed, and the power wire
shorts to ground (between the battery and the amplifier), a fire can result. The fuse at the
battery should be of the same value as the fuse supplied with the amplifier. Consult your
Authorized
PPI
Dealer for an appropriate in-line fuse that meets the needs of your
installation.
Installation
PRIOR TO INSTALLATION of your new ArtSeries Amplifier it is important to consider
the following: In your profession, your abilities and expertise insure a job well done.
This is also true of professional car audio installers. It is their chosen profession, and
why they do best. PPI believes so strongly in it's responsibility to you, that we invest
heavily in hands-on training of professional installers. Our comprehensive system
design and installation seminar provides our authorized dealers with the latest techniques to deal with the complexities of car audio today. There is more than meets the
eye to insure that a car stereo reaches it's fullest potential. The trained professional,
through experience, can approach, recognize, and address all the needs of the
mobile audio environment. PPI highly recommends that this amplifier and/or any
other mobile audio equipment be installed by a trained professional.
Tools / Parts Needed for Installation (not supplied):
Small flat blade screwdriver Phillips screwdriver
Wire cutters Wire strippers
Soldering iron Solder
Flux cleaner 5 washers, 4 #6 and 1 #8 sheet metal screws
2 - ring connectors In-line fuse holder and fuse
Speaker wire - 16 gauge or larger Power and Ground wire - 12 gauge or larger
Heatshrink Grommets
Silicone or similar material
Mounting
To prevent damage to the amplifier while driving, mount it in a secure place. Choosing
the appropriate location will depend upon your vehicle and the complexity of your system
design. It may be mounted in any compatible space that is convenient to your needs and
provides sufficient airflow. Adequate ventilation allows the amplifier to dissipate the heat
that develops during operation. Inadequate ventilation may result in overheating. The
thermal protection circuit will engage when the heatsink temperature reaches 75
degrees Celsius. The amplifier will automatically return to normal operation once the
heatsinkcools.
Typical mounting locations include: trunk and passenger compartment (floor or under
seat). Never mount the amplifier in a location, which would subject it to immersion or
exposure to water.
The Art Series' uniquely shaped heatsink is designed for high-efficiency cooling but
improper mounting may compromise its ability to cool. When mounting the amplifier in a
confined space (i.e. under), care must be taken to ensure that at least two inches of
clearance is provided around the amplifier. If the amplifier is located in an area which
has restricted air-flow or is totally enclosed, a fan may be used to improve air circulation.
Power and Ground
Before beginning, disconnect the negative (-) terminal of the battery before working on the
positive terminal to prevent a short to ground. Reconnect the negative terminal only after all
connections have been made.
For safety reasons, PPI recommends that the power cable ve fused at the positive
terminal of the battery. If this fuse is not installed, and the power wire shorts to
ground (between the battery and the amplifier), a fire can result. The fuse at the battery should be of the same value as the chassis fuse located on the right-hand end
panel of the amplifier. Consult your Authorized PPI dealer for an appropriate in-line
fuse holder that meets the needs of your installation. We suggest crimping and soldering all wire connections. Insulate the connection with heat shrink to prevent a
short to ground
The ground wire should be of teh same gauge as the power wire. In systems with
over 800 watts of total output power, the ground and power cables should run parallel to each other to avoid unwanted system noise. As a "rule of thumb", use as short a
length of wire as possible. Locate an area near the amplifier that is metal (the floor is
ideal) and clean an area about the size of a quarter to bare metal. Drill a pilot hole in
the middle of this area. Be Careful!! Inspect the area underneath to be sure you aren't
drilling into wires, brake or fuel lines, etc. Terminate the wire with a ring connector
and attach it to the bare metal using a #8 sheet metal screw and washer (not supplied). We suggest crimping and soldering this connection. Insulate the connection
with heat shrink. It is important that this connection be solid. After the conenction is
complete, coat the area with silicone or some similar material to prevent rust from
developing.
Once you have run both the power and ground wires, it's time to connect the cable to
the amplifier. Be sure that you have not reconnected the ground cable to the negative post of the battery. Cut off excess wire and, using wire strippers, strip the power
and ground cables 1/4 inch. Locate the power and ground connector (supplied). On
the under side of the connector are two slotted screws. With a small flat bladed
screw driver, loosen these screws before attempting to insert the cables. After you
have inserted the bared end of each cable into the connector, secure it by tightening
the associated screw. If inserting larger gauge wire presents a problem, tinning the
wire with solder may help. Be sure each connection is tight. Once the wires are
secure, the connetor may be plugged into the amplifier. Please Note: the power /
ground connector is keyed to a slot in the end panel and can only be inserted one
way - with the head of the fastening screws pointing down. (Refer to Figure C.)
The Art Series amplifiers are designed to operate from a car's (+) positive 12 volt,
negative ground electrical system. PPI recommends that the power and ground cables
be a minimum of 6 gauge for the A1200, 10 gauge for the A300 & A600 and 12 gauge
for the A100 & A200. Depending upon the complexity of your system, larger gauge wire
may be needed. PPI's Exclusive Wire Connection System will accept up to 6 gauge
cable.
The main power cable should run from the amplifier location, through the vehicle to
the battery, avoiding sharp corners, creases, and sharp body parts. When passing
through any metal wall (i.e. firewall, etc), a grommet must be used to prevent the
wire from chaffing and shorting to ground.
Remote Turn-On
Bridging
In order for the amplifier to turn on, a remote turn-on wire must be connected to a
switched 12 volt source. Typically, the source unit provides a power antenna
(remote) turn on lead which will turn on the amplifier when the source unit is activated. If this is unavailable, or if voltage drops below 7 volts, a switched 12 volt source
must be used (Refer to page 9, Central Muting and the ACM-420).
Run a wire from the amplifer location through the vehicle to the switched 12 volt
source. Observe the same precautions for routing this cable that you followed for
running the power cable. Cut off excess wire and, using wire strippers, strip the wire
1/4 inch.
Four channel ArtSeries amplifiers are shipped with two speaker connectors. One will
accommodate five wires, and one will accommodate four wires. Locate the five wire
connector which we will refer to as the speaker / remote turn-on connector. On the
underside of the connector are five slotted screws. Loosed the middle screw before
attempting to insert the remote turn-on lead into the end of the connetor. After the
wire is inserted, secure it by the tightening the associated screw. If inserting larger gauge
wire presents a problem, tinning the wire with solder may help. Be sure the connection is tight. You are now ready to connect the speakers (Refer to Figure D).
Speaker Connection
Fun the speaker wires from the amplifier locations, through the vehicle to the speakers. Observe the same precautions for routing these wires that you followed for running the power and remote turn-on cables. It is important to use 16 gauge or larger
wire, for proper signal transfer. Cut off excess and, using wire strippers, strip 1/4
inch. Once again, locate the speaer / remote turn-on connector. Loosen the four
remaining screws on the underside of the connector. Insert the speaker leads, one at
a time, into the end of the connector. Check to make sure you've maintained proper
polarity before securing each wire. If inserting larger gauge wire presents a problem,
tinning the wire with solder may help. Be sure the connection is tight. Repeat this
process for the remaining four wire connector on four channel amps. The connectors
may now be plugged into the amplifier (Refer to Figure D).
All ArtSeries amplifier are capable of being bridged into a mono output due to the
internal design of the amplifier. This feature permits the creation of a mono channel
for a subwoofer or center channel. Also bridging adds flexibility of operation. Any of
the ArtSeries two-channel amplifiers may be used in a one channel (mono), two
channels stereo, or 3 channels - 2 channels stereo and one channel derived mono
configuration. ArtSeries four-channel amplifiers may be used as 2 mono channels, 3
channels - 2 channels stereo and one bridged mono channel, 4 channels - 2 channel (stereo) front and rear, 5 channels - 4 channels stereo and one derived mono
channel, or 6 channels - 4 channels stereo and 2 derived mono channels.
Deriving the mono channel is accomplished by using the left channel positive
wire as the positive speaker wire and the right channel negative wire as the
negative speaker wire. It is important that a minimum of 4 Ohm impedance is
observed. If the impedance drops below 4 ohms while the amplifier is wired in the
mono configuration, the AM II protection circuit will engage the output power will be
reduced.
The ability to run stereo satellites wile simultaneously running a mono output from
the same output stage is accomplished simply by running the stereo speakers normally and tappng into the appropriate wires for teh "Mixed Mono" channel (left channel positive wire as the positive speaker wire and the right channel negative wire as
the negative speaker wire). Again, for optimum performance, speaker impedance
should be 2 Ohms on the stereo channels and 4 Ohms on the mono channel.
Inputs
On the left side panel of two-channel ArtSeries amplifier are one pair of RCA left
and right inputs. Four-channel models feature two pair of RCA inputs and a "2/4 way"
switch. If both "Input 1" and "Input 2" are to receive the same input signal, place the
"2/4 way" switch in the on (in) position. This will parallel the inputs together internally
in the amp. In this mode, either set of inputs may be used.
Gain Control
On the left end panel, next to the inputs, is the gain control. This control adjusts the
level of the input signal of your source unti. This control requires a small flat-bladed
screwdriver for adjustment. Upon installation of the amplifier, the gain control must
be adjusted. This can be done by first turning the gain all the way down (counterclockwise). Turn the volume on the source unit up to two-thirds. Then adjust the gain
control until the desired volume is obtained without audible distortion.
Low Impedance Indicator
Adjusting Crossover Input Gains:
AM II circuitry will lower output power to maintain uninterrupted operation whenever the
amplifier senses an impedance load of less than 2 Ohms. The Low Impedance Indicator
(left-side end panel) is provided to let you know when the amplifier is operating in this
mode. It is important to note that there is no increase in output power below the 2 Ohm
threshold. Maximum power is achieved at 2 Ohms.
In the case of a short circuit, AM II will engage to protect the shorted channel but will
continue to play the unaffected channel. When this occurs, audible distortion will be
heard. Turn-off the system and repair the short. Once the problem has been repaired,
the amplifier will return to normal operation.
System Tuning
In order to achieve maximum signal-to-noise performance from a high quality mobile
sound system, it is desirable to use high signal levels wherever possible in the
interconnection cables. High signal levels will reduce the effect of induced noise. The
peak level of an audio signal is usually determined by the clipping level of electronic
components. The following procedure should be used as a guide when the system
installation is complete.
Adjusting Equalizer Input Gains:
1. Turn the equalizer's volume control to minimum.
2. Turn the source unit volume 1/2 to 3/4 of maximum. If available on your unit, set
the output level to maximum. Some units may have a switch.
3. If available, set selector switch to either input 1 or input 2.
4. Adjust all equalizer input gains to minimum.
5. For the chosen input play the respective music source. A loud music passage
is desired.
6. For the chosen input, increase the left input gain control until the onset of audible
distortion. Then decrease the gain prior to the immediate point of audible
distortion. This setting will minimize system background noise and prevents
overloading of the equalizer. Adjust, for the same input, the right input gain
control for proper left / right balance.
7. Set selector switch to the alternative source unit, if used, and repeat steps 5 and
6.
8. Adjust crossover next.
1. Adjust all crossover gain controls to 0 dB, 1/2 of maximum sensitivity.
2. Adjust all amplifier gains to 1/2 of maximum sensitivity.
3. Turn the volume knob on the equalizer to a maximum of 3 o'clock.
4. Increase the gain of the crossover until the onset of audible distortion. Then
decrease the gain prior to the immediate point of audible distortion. This setting
will minimize system background noise and prevents overloading of the
crossover.
5. Repeat step 4 for any remaining crossovers in the system.
6. Adjust the input gains next.
NOTE: In manu multi-crossover / accessory systems, the gain of some
crossover and accessories may need to be further decreased to achieve
proper balance.
Adjusting the Amplifier's input Gain:
1.
Adjust the amplifier's input gain to 1/2 maximum sensitivity
2.
Turn the volume knob on the equalizer to a maximum of 3 o'clock
3.
Increase the gain (clockwise) until the onset of audible distortion. Then
decrease the gain counterclockwise prior to the immediate point of audible
distortion. This setting will minimize system background noise and prevents
overloading of the amplifier.
Repeat step 3 for any remaining amplifiers in the system.
4.
NOTE: Depending on the sensitivity of the system's preamp(s), the gain of
the amplifier(s) may not need adjustments. Also, in many multi-amplifier
systems, the gain of some amplifiers may need to be further decreased to
achieve proper balance.
TROUBLESHOOTING
p
If for some reason your system fails to operate properly, please refer to this guide. If you are
unable to resolve the problem, consult your Authorized
PPI
Dealer or call
1-800-62-POWER.
NO SOUND
Is the power LED illuminated?
Check fuses in power wire.
Be sure turn-on lead is connected.
NO SOUND IN ONE CHANNEL
Check speaker leads and inspect for a short to ground or
an open connection.
Check pre-amp leads. Reverse left and right leads to see
if the problem is before the amplifier.
Check Mono Bridge and Bi-Amp crossover switches on
other units prior to the amp.
If the problem is in the amp, have your Dealer inspect
the unit.
AMP TURNING OFF
Istheampabletocoolproperly?
Check speakers for shorts or damage.
Make sure power and ground are secure.
PPI
Have
Dealer ins
ect amp.
Loading...