Claas AXION 850 C.I.S., AXION 840 C.I.S., AXION 820 C.I.S., AXION 810 C.I.S., AXION 840 CMATIC Operator's Manual
...
AXION 850-840-830-820-810 C.I.S.
Operator's manual
ABOUT THIS OPERATOR'S MANUAL
6543
This is the original operator's manual. It will simply be referred to as the "operator's manual" throughout this
document
This operator's manual complies with the regulations currently in force in the first country the tractor has been
delivered to.
This operator's manual contains the instructions for using, adjusting, servicing, cleaning and transporting the
tractor. It is essential to be familiar with all of these instructions in order to:
- Improve the performance of the tractor
- Increase the tractor's availability
- Extend the service life of the tractor
- Ensure the correct working conditions in terms of both safety and comfort
If any maintenance operations are missed or if the tractor is used incorrectly, the following is possible:
- An increased safety risk
- Premature wear of the tractor
- A reduction in tractor performance
- Loss of output and time
Have the tractor serviced regularly by an approved CLAAS distributor.
This operator's manual can be considered contractual. CLAAS has a policy of continuous technical improvement to
all its products, and therefore reserves the right to change without notice and at any time the details contained in
this operator's manual.
The description of the models contained in this operator's manual was established from technical specifications
known at the time this operator's manual was written. The operator's manual contains all of the equipment
(standard or optional) that exists for these models. The presence of this equipment in the tractor depends on the
tractor version and options chosen by the purchaser and the country of sale for this tractor.
Servicing operations during the warranty period are mandatory; failure to carry them out will nullify the contractual
warranty.
Failure to observe the instructions for use and maintenance of the tractor as described in this operator's manual
definitively excludes any possibility of recourse to the CLAAS warranty system.
The instruction and warning plates affixed to the tractor give important information about possible risks of use.
Following these instructions will guarantee your safety!
Front/rear tools have a separate operator's manual.
The CLAAS distribution network is available to respond to any questions that you may have relating to the content
of this operator's manual.
Important information concerning this operator's manual
Important information concerning this operator's manual appears at the end of the manual:
AXION 850-810 C.I.S. - 02/2012 - en 3
1 - Address of CLAAS company headquarters
CLAAS KGaA mbH
Postfach 1163
33416 Harsewinkel
Tel. +49 (0)5247 12-0
www.claas.com
XX XXXX XXX X
OM XXXXX XXX
XX - XX/XXXX
Printed in France
6
8
7
5
4
3
1
2
2 - Phone number to call if necessary
3 - Address of CLAAS company website
4 - Reference of this operator's manual
5 - Designation of this operator's manual
6 - Language code for this operator's manual
7 - Publication date of this operator's manual
8 - Country where this operator's manual was printed
The reference, designation and publication date of this operator's manual also appear at the bottom of each page
of the operator's manual. The reference of the operator's manual should be quoted in any query concerning the
operator's manual and when ordering additional copies.
Classification into modules
The sections in this manual are categorised into modules, as far as the contents permit. The structure of these
modules is identical in each section.
The different product groups have different module structures. CLAAS always endeavours to retain these module
structures in each document.
Direction indications
Indications such as front, rear, right-hand and left-hand are always in the context of the direction of travel of the
tractor.
In the illustrations, the direction of travel may be indicated by a direction arrow.
Text and illustrations
Photos and graphics have been kept neutral wherever possible. If this is not the case, additional information is
added underneath the illustration.
Texts and illustrations have been kept neutral wherever possible. If this is not the case, the preceding subtitle takes
into account the differences.
Highlighting dangers and warnings
In the operator's manual, all points concerning personal safety and the safe use of the tractor are indicated by the
following symbols. Ensure that other users are also made aware of all safety advice.
000msn00gm
4
AXION 850-810 C.I.S. - 02/2012 - en
CAUTION
Instructions which must be strictly followed to prevent any risk of personal injury.
Important: Instructions which must be strictly followed to prevent damage to the tractor and its
environment.
Note: Instructions to be followed to ensure more efficient/suitable use of the tractor
Specific terminology
In this operator's manual, "tool" refers to any equipment hitched to the tractor, whether carried or towed.
Likewise, the term "risk zone" refers to all locations with an increased risk of accident.
- Around the tractor and the tools hitched to the tractor
- Between the tractor and the carried/towed tools
- In the deployment or movement area of the tools
Technical specifications
The technical specifications, dimensions and weights are provided on a non-binding basis. CLAAS reserves the
right to modify them as part of the technical development, subject to errors.
Optional and additional equipment
Optional equipment consists of tractor equipment variants. Different variants are available but only one can be
fitted at a time.
Additional equipment consists of tractor equipment variants which can be fitted as accessories but which are not
part of the tractor's standard equipment.
The two terms refer to the possible variants. Standard equipment and equipment variants may vary according to
the country.
AXION 850-810 C.I.S. - 02/2012 - en 5
VALIDITY OF THE INSTRUCTIONS
This operator's manual is valid for the following tractors:
Type of tractor
5543
Tractor serial number
From To
AXION A3000050
The operator's manual describes the possible equipment for your tractor. Your tractor's equipment is listed in your
order confirmation.
6 AXION 850-810 C.I.S. - 02/2012 - en
UNITS
The units used in this document are in line with international system of units:
5639
Physical Unit Name Symbol of unity
Multiples and sub-multi-
ples of the unit
Size Metre m mm - cm
Volume Cubic meter m³ cm³ - dm³
Liter l ml - cl
Angle Degree °
Time Second s
Minute min
Hour h
Linear speed Kilometer per hour km/h m/h
Rotation speed Revolution per minute 1/min
Weight Kilogram kg g
Forced Newton N
Torque Newton meter Nm
Pressure Pascal Pa
Power Watt W kW
Flow rate Liter per minute l/min
Temperature Degree Celsius °C
Power voltage Volt V mV
Electric intensity Ampere A mA
Resistor Ohm Ω kΩ
Sound level Bel B(A) dB(A)
The date format used in this document also complies with the international system:
Year-Month-Day
Example: 2010-07-15
AXION 850-810 C.I.S. - 02/2012 - en 7
CHAPTER SYMBOLS
kg
mm
l
REF CHAPTERS SYMBOLS
5887
A
B
C
D
E
F
G
IDENTIFICATION - CERTIFICATION - SAFETY
CAB
ELECTRICAL SERVICES
ENGINE
TRANSMISSION
FRONT AXLE
REAR EQUIPMENT
M
H
I
J
K
L
FRONT EQUIPMENT
CLAAS INFORMATION SYSTEM
WHEELS AND TYRES
CHARACTERISTICS
MAINTENANCE
OPERATIONS THAT ARE MANDATORY UNDER THE GUARANTEE
8 AXION 850-810 C.I.S. - 02/2012 - en
CONTENTS
A - IDENTIFICATION - CERTIFICATION - SAFETY
1 TRACTOR INFORMATION PLATE ....................................................................................... A. 2
2 TRACTOR POWER LABEL ................................................................................................... A. 4
3 MOTOR INFORMATION PLATE ........................................................................................... A. 5
4 CAB IDENTIFICATION PLATE ............................................................................................. A. 6
5 EUROPEAN REGULATION ................................................................................................... A. 7
6 SAFETY .................................................................................................................................. A. 8
6.1
6.2
SAFETY INSTRUCTIONS ........................................................................................................ A. 8
SAFETY STICKERS WITH WARNING PICTOGRAMS ......................................................... A. 23
B - CAB
1 OPERATING AND WORKING ENVIRONMENT ................................................................... B. 2
1.1
1.2
1.3
2 LIGHTING, INDICATORS AND SAFETY .............................................................................. B. 6
2.1
2.2
2.3
2.4
2.5
3 STARTING CONTACT ......................................................................................................... B. 11
4 MULTIFUNCTION ARMREST ............................................................................................. B. 12
5 SEATS .................................................................................................................................. B. 13
INSTRUMENTS AND CONTROLS (DRIVING POSITION) ...................................................... B. 2
INSTRUMENTS AND CONTROLS (PANEL) ........................................................................... B. 4
STOWAGE AND ACCESSORIES ............................................................................................ B. 5
DESCRIPTION ......................................................................................................................... B. 6
LOW/HIGH BEAMS AND HORN .............................................................................................. B. 7
WORKING LIGHTS AND ROTATING BEACON ...................................................................... B. 8
OVERHEAD LIGHT .................................................................................................................. B. 9
REAR VIEW MIRRORS ............................................................................................................ B. 9
5.1
5.2
DRIVER'S SEAT ..................................................................................................................... B. 13
PASSENGER SEAT ............................................................................................................... B. 15
6 STEERING WHEEL ............................................................................................................. B. 17
7 INSTRUMENT PANEL ......................................................................................................... B. 18
7.1
7.2
7.3
7.4
DESCRIPTION ....................................................................................................................... B. 18
OPERATION ........................................................................................................................... B. 20
OPERATION ........................................................................................................................... B. 23
CALIBRATION ........................................................................................................................ B. 24
8 DISPLAY .............................................................................................................................. B. 25
8.1
TRANSMISSION DISPLAY .................................................................................................... B. 25
AXION 850-810 C.I.S. - 02/2012 - en
9 HINGED PANELS AND WINDOWS .................................................................................... B. 26
10 SIGHT ................................................................................................................................... B. 30
11 HEATING - VENTILATION - MANUAL AIR CONDITIONING ............................................. B. 31
11.1
11.2
DESCRIPTION ....................................................................................................................... B. 31
OPERATION ........................................................................................................................... B. 31
12 HEATING/VENTILATION/AUTOMATIC CLIMATE CONTROL .......................................... B. 36
12.1
12.2
DESCRIPTION ....................................................................................................................... B. 36
OPERATION ........................................................................................................................... B. 36
13 CAB SUSPENSION ............................................................................................................. B. 40
C - ELECTRICAL SYSTEM
1 CHARACTERISTICS ............................................................................................................. C. 2
2 TRAILER/IMPLEMENT LIGHT SOCKET .............................................................................. C. 3
3 ELECTRIC CABINET SUPPLY SOCKET ............................................................................. C. 5
4 EVENT COUNTER SOCKET ................................................................................................. C. 6
5 ISO SOCKET .......................................................................................................................... C. 7
6 ISOBUS SOCKET .................................................................................................................. C. 8
7 PROVISION FOR THE INSTALLATION OF A CONTROL CASING IN THE CAB ............... C. 9
7.1
7.2
FITTING BOX MOUNTING ....................................................................................................... C. 9
CABLE ROUTING ..................................................................................................................... C. 9
8 BATTERY ............................................................................................................................. C. 10
8.1
8.2
BATTERY COMPARTMENT .................................................................................................. C. 10
BATTERY MASTER SWITCH ................................................................................................ C. 11
9 FUSES AND RELAYS ......................................................................................................... C. 12
9.1
9.2
9.3
9.4
RECOMMENDATIONS ........................................................................................................... C. 12
CAB-MOUNTED SERVICES FUSE BOX ............................................................................... C. 12
CAB TOP FUSE BOX ............................................................................................................. C. 15
PRIMARY SERVICES FUSE BOX ......................................................................................... C. 18
D - ENGINE
1 CHARACTERISTICS ............................................................................................................. D. 2
2 DISPLAYS .............................................................................................................................. D. 4
2.1
3 SAFETY .................................................................................................................................. D. 5
3.1
3.2
3.3
INSTRUMENT PANEL .............................................................................................................. D. 4
OPERATION ............................................................................................................................. D. 5
INSTRUMENT PANEL .............................................................................................................. D. 5
RECOMMENDATIONS ............................................................................................................. D. 5
4 ENGINE HOOD ...................................................................................................................... D. 7
4.1
4.2
ONE-PIECE HOOD .................................................................................................................. D. 7
SIDE PANELS .......................................................................................................................... D. 7
AXION 850-810 C.I.S. - 02/2012 - en
Loading...