Citroën Berlingo First Dag 2008 Owner's Manual
4 -
5
INSTRUMENTS AND CONTROLS
12. Windscreen demisting vents.
13. Speaker (tweeter).
14. Side window demisting vents.
15. Side adjustable heating/
ventilation vents.
16. Passenger air bag disarming
control.
17. Upper glove box or passenger
air bag.
18. Lower glove box.
19. Audio RD3.
20. Heating/air conditioning controls.
21. Storage.
22. Removable ashtray.
23. Gear lever.
24. Lighter.
25. Handbrake.
26. Heated seats control.
27. Steering lock and ignition.
28. Steering wheel adjustment
control.
29. Bonnet release.
30. Fuse box.
31. Headlamp height adjustment.
32. Passenger's electric mirror
control.
1. Speed limiter/cruise control stalk.
2. Lights and direction indicators
stalk.
3. Driver's air bag.
Horn.
4. Instrument panel.
5. Audio equipment steering wheel
control.
6. Windscreen wipers/
wash-wipe stalk.
7. Central adjustable heating/
ventilation vents.
8. Hazard lights button.
9. Multifunction display or clock.
10. Central lockingbutton.
11. Controls:
- Electric windows.
- Demisting of rear door
windows.
- Air conditioning.
-
6 -
THE KEYS
STARTING
The remote control
The keys allow you to switch on the
ignition and operate the passenger
air bag disarming switch, as well as
to independently operate the locks
on the doors and the fuel fi ller cap.
Central locking
From the front doors, the keys allow
you to lock and unlock all of the doors.
If one of the doors is open, it is impossible to operate the central locking.
The remote control performs the
same functions at a distance.
Locking
Press button A to lock the vehicle.
This is confi rmed by fi xed lighting of the
direction indicators for approximately
two seconds.
Unlocking
Press button B to unlock the vehicle.
This is confi rmed by rapid fl ashing of
the direction indicators.
Locating the vehicle
To locate your vehicle, previously
locked, in a car park:
press button A , the courtesy
lights come on and the direction
indicators fl ash for a few seconds.
STOP position (S):
The ignition is off.
To release the steering, turn the
steering wheel slightly while turning
the key, without forcing it.
Accessories position (A):
The ignition is off but the accessories
can be used.
On position (M):
The ignition is on.
Starting position (D):
Operates the starter.
Release the key when the engine
has started. Never operate the starter
while the engine is running.
52
7
WINDSCREEN WIPERS
STEERING WHEEL STALKS
LIGHTING
Vehicles fi tted with a rear
fog lamp (ring B)
Turn the ring forwards.
Vehicles fi tted with
front fog lamps and a
rear fog lamp (ring B)
-
Front and rear lights (ring A)
Lights off
Side lights
Dipped headlamps/
Main beam headlamps
Front fog lamps (1 st turn of the ring
forwards).
Front fog lamps and rear fog lamp
(2 nd turn of the ring forwards).
To switch off: turn the ring rearwards.
59 60
Front
2 Rapid wipe (heavy rain).
1 Normal wipe (moderate rain).
I Intermittent wipe.
0 Off.
Single wipe.
Windscreen wash-wipe: pull the stalk
towards you.
Rear
Off Wash-
Intermittent
wipe
wipe
8 -
FRONT SEATS
Never travel with the head
restraints removed.
2. Armrest.
3. Seat back angle adjustment.
4. Forwards-backwards adjustment.
5. Storage drawer (passenger).
40
1. Head restraint height adjustment.
9
AIR BAGS
Front air bags
These are folded in the centre of the
steering wheel for the driver and in
the fascia for the front passenger.
They are deployed simultaneously,
except in cases where the passenger
air bag is disarmed.
Precautions regarding the
passenger air bag
disarm the air bag if you install a
rear-facing child seat,
activate the air bag for an adult
passenger.
Disarming the passenger air bag
With the ignition off, insert the
ignition key into the passenger
air bag switch 1 and turn it to the
"OFF" position.
As soon as you remove the child
seat, turn the air bag switch to the
"ON" position to activate the air
bag again.
Disarming check
With the ignition switched
on (2 nd notch), illumination
of this warning light indicates that the passenger air
bag is disarmed (switch in
the "OFF" position).
The warning light remains on throughout the duration of disarming.
Side air bags
Side air bags are incorporated into
the front seat back frame, on the
door side.
They are deployed independently of
each other, on whichever side the
collision occurs.
-
77
78
10 -
STEERING WHEEL HEIGHT
ADJUSTMENT
ELECTRIC WINDOWS
EXTERIOR MIRRORS
1. Driver's electric window.
2. Passenger's electric window.
Manual mode:
Press the switch. The window stops
as soon as the switch is released.
Automatic mode (driver):
Press and hold the switch. One
touch completely opens or closes
the window.
Move the manual control 3 in all
four directions to adjust.
Electric control for the
passenger's side mirror
From the driver's seat, adjust in
all four directions by operating
the control 4 .
61 62 66
When stationary, push the control A
forwards to unlock the steering
wheel.
Adjust the height of the steering
wheel.
Lock it by pulling control A towards
you fully.
-
SPEED LIMITER
This limiter indicates the status of
selection of the function on the instrument panel and displays the
programmed speed. The minimum
speed which can be programmed is
at least 18 mph (30 km/h).
It prevents exceeding of the speed programmed by the driver, this function
remains active regardless of any action
on the brake or clutch pedals. On the
other hand, pressing the accelerator
pedal to the point of resistance does
not have any effect.
It is possible to exceed the programmed speed temporarily by press-
ing the accelerator fi rmly beyond this
point of resistance.
The operating actions must be carried
out with the engine running.
The cruise control has a display on
the instrument panel to indicate the
programmed reference speed.
It enables the vehicle to maintain the
reference speed programmed by the
driver.
In order for it to be programmed or
activated, the vehicle speed must be
greater than 25 mph (40 km/h) with
at least fourth gear engaged.
If the vehicle is fi tted with
a speed limiter and cruise
control, these functions cannot be activated at the same
time.
11
74 72
12 -
HEATING
N° Symbol Function
1
2
3
4
N° Symbol Function
1
2
3
4
Air fl ow adjustment.
Air fl ow adjustment
and air intake control.
Temperature
adjustment.
Air distribution
adjustment.
Air conditioning
control.
Air fl ow adjustment
and air intake
control.
Temperature
adjustment.
Air distribution
adjustment.
36
38
13
RECOMMENDED INTERIOR SETTINGS
I require...
Heating or Manual air conditioning
Air distribution Air fl ow
Air recirculation/
Intake of exterior air
Temperature Manual AC
-
HOT
COLD
DEMISTING
DE-ICING
14 -
FRONT FITTINGS
1.
Storage compartments in the doors.
A. Bottle holder.
B. Can holder.
C. Storage compartment.
2. Overhead storage.
3. Map reading light.
4. Courtesy light.
5. Sun visors.
6. Glove box.
7. Lighter.
8. Removable ashtray.
9. Storage drawer (passenger).
65
-
REAR LAYOUT
Stowing rings
For greater safety, always ensure that the loads transported
are secured fi rmly.
1. Load space cover.
2. High load retaining net.
3. Stowing rings.
4. Side door storage compartment.
5. Trays between the front and rear
seats.
6. Seat back storage pockets.
15
67
68
16 -
OPENING THE BONNET
FILLING WITH FUEL
This operation must be carried out
with the engine switched off .
Insert the key then turn it to the
left.
Remove the cap.
A label indicates which type of fuel to
use.
When you fi ll your tank, do not continue
after the third cut-off of the pump. This
could cause engine malfunctions.
The capacity of the tank is approxi-
mately 55 litres for petrol engines
and 60 litres for Diesel engines.
Low fuel level
warning light
From the time this light comes on,
you have enough fuel left to cover
approximately 30 miles (50 km) .
Note: the right-hand sliding side door
cannot be opened while the fuel tank
cap is removed.
Inside the vehicle: Pull the control
on the left-hand side, under the fascia
panel.
Outside the vehicle: Lift the control,
raise the bonnet and secure the strut
to keep the bonnet open.
58 58
18 -
INSTRUMENT PANEL: PETROL - DIESEL
1. Seat belt not fastened warning
light
2. Front and side air bags warning
light
3. Passenger air bag disarmed
warning light
4. Front fog lamps indicator light
5. Anti-lock braking system (ABS)
warning light
6. Rear fog lamp indicator light
7. Diesel pre-heat warning light
8. Left hand direction indicator
9. Total distance recorder, service
indicator and engine oil level
indicator
10. Right hand direction indicator
11. Emission control system warning
light
Main beam headlamps indicator light
12.
13. Handbrake, low brake fl uid
level and electronic brake force
distribution warning light
14. Dipped beam headlamps
indicator light
15. Battery charge warning light
16. Engine oil pressure and
temperature warning light
17. Water in diesel fi lter warning light
18. Low coolant level warning light
19. Coolant temperature indicator
20. Total distance recorder button
21. Central (STOP) warning light
22. Speedometer
23. Rev counter
24. Lighting rheostat button
25. Fuel level indicator
26. Low fuel level warning light
27. Speed limiter/cruise control
display
19
INSTRUMENTS AND
-
A permanently lit warning light or
one fl ashing, with the engine running, indicates an operating fault
of the unit concerned. The illumination of certain warning lights
may be accompanied by an audible signal and a message on the
display. Do not ignore this warning: consult a CITROËN dealer as
soon as possible.
If the central STOP warning light
comes on when you are driving,
stop your vehicle immediately,
where it is safe to do so.
Central (STOP)
warning light
Linked to the warning
lights:
- ''engine oil pressure and tempera-
ture'',
- ''low coolant level'',
- 'handbrake'',
- ''low brake fl uid level'',
- ''electronic brake force distribution
system fault''.
Linked with the "coolant temperature"
indicator.
You must stop if the light fl ashes
with the engine running.
Consult a CITROËN dealer.
Engine oil pressure
and temperature
warning light
Linked to the central (STOP) warning
light.
You must stop.
This warning light indicates one of
the following:
- insuffi cient oil pressure indicated
by the message "Oil pressure
insuffi cient" on the display.
- a lack of oil in the lubrication circuit.
Top up the level.
- an oil temperature which is too high.
To lower the oil temperature, reduce
your speed.
Lighting of the warning light is ac-
companied by an audible signal.
Consult a CITROËN dealer.
Low engine coolant
level warning light
Linked to the central (STOP) warn-
ing light.
This comes on for a few seconds
when the ignition is switched on.
Lighting of this warning light is ac-
companied by an audible signal and
the message "Top up engine fl uid
level" on the display.
You must stop.
Wait for the engine to cool before
topping up the level.
The cooling circuit is pressurised.
In the event of breakdown and to pre-
vent any risk of burns, unscrew the
cap by two turns to allow the pressure
to drop.
When the pressure has dropped, remove the cap and top up the level.
Consult a CITROËN dealer.
Handbrake, low
brake fluid level and
Electronic Brake Force
Distribution system
fault warning light
Linked to the central (STOP) warning
light.
This comes on each time the ignition
is switched on.
Lighting of this warning light is ac-
companied by an audible signal and
a message on the display indicating
the cause of the warning:
- "Handbrake on", if the handbrake
is applied or not fully released.
- "Brake fl uid level low" if there is
an excessive drop in brake fl uid
level (if the warning light remains
on even when the handbrake is
released).
- "Braking fault" is displayed
together with the ABS warning
light, indicating a malfunction
of the Electronic Brake Force
Distribution system. You must
stop.
Consult a CITROËN dealer.
20 -
Anti-lock braking
system (ABS) warning
light
This comes on for a few seconds each
time the ignition is switched on.
If the warning light remains on or
comes on above 8 mph (12 km/h),
this indicates an ABS malfunction.
However, the vehicle retains conven-
tional servo-assisted braking.
Lighting of this warning light, accom-
panied by an audible signal and the
message "ABS fault" on the display,
indicates an ABS fault.
Consult a CITROËN dealer.
Battery charge warning
light
This comes on for a few seconds when the ignition is
switched on. Lighting of this warning
light, when the engine is running, accompanied by an audible signal and
the message "Battery charge fault"
on the display, indicates one of the
following:
- faulty operation of the charging
circuit,
- slack battery or starter terminals,
- a cut or slack alternator belt,
- an alternator failure.
Consult a CITROËN dealer.
Emission control
system warning light
This comes on for a few seconds each time the ignition is
switched on.
If it comes on with the engine running,
accompanied by an audible signal
and the message on the display:
- "Antipollution fault", this
indicates a failure of the emission
control system
- "Catalytic converter fault", this
indicates a malfunction of the
injection or ignition system. There
is a risk of damage to the catalytic
converter (petrol engine only).
Consult a CITROËN dealer.
Diesel engine pre-heat
warning light
Wait until the warning light
goes out before starting the
engine.
If the temperature is high enough,
the warning light comes on for less
than one second. You can start the
engine without waiting.
Low fuel level
warning light
This comes on for a few
seconds when the igni-
tion is switched on.
When the ignition is on, it is accom-
panied by an audible signal and the
message "Fuel level low" on the
display.
If it fl ashes with the fuel gauge needle
in the lowest position, when the igni-
tion is on, this indicates a malfunction
of the fuel gauge.
When this warning light fi rst comes
on, you have enough fuel left to drive
approximately 30 miles (50 km) .
Capacity of the tank:
- approximately 55 litres for petrol
engines,
- approximately 60 litres for Diesel
engines.
Water in diesel filter
indicator *
There is a risk of damage to the
injection system.
Consult a CITROËN dealer as soon
as possible.
* According to country.
21
-
Seat belt not fastened
warning light *
When the ignition is switched
on, this indicator light comes
on if the driver has not fastened his
seat belt.
Above 12 mph (20 km/h), the warn-
ing light fl ashes for two minutes.
Once the two minutes have elapsed,
the warning light remains on until the
driver fastens his seat belt.
Passenger air bag
disarmed warning
light *
Lighting of this warning light is accompanied by the message "Passenger
air bag deactivated" on the display.
If the passenger air bag is disarmed,
the warning light comes on when the
ignition is switched on and it remains
on.
Always consult a CITROËN dealer if
the warning light fl ashes.
Front and side air bags
warning light
This comes on for a few seconds when the ignition is
switched on.
With the engine running, illumination
of this warning light accompanied by
an audible signal and the message
"Air bag fault" on the multifunction
display, indicates a fault in the air
bags.
Consult a CITROËN dealer.
Coolant temperature indicator
- needle in zone (A) , the tempera-
ture is correct,
- needle in zone (B) , the tempera-
ture is too high. The central STOP
warning light fl ashes, accompanied by an audible signal and the
message "Engine coolant temp.
too high" on the display.
You must stop.
Consult a CITROËN dealer.
* According to country.
21
-
Seat belt not fastened
warning light *
When the ignition is switched
on, this indicator light comes
on if the driver has not fastened his
seat belt.
Above 12 mph (20 km/h), the warn-
ing light fl ashes for two minutes.
Once the two minutes have elapsed,
the warning light remains on until the
driver fastens his seat belt.
Passenger air bag
disarmed warning
light *
Lighting of this warning light is accompanied by the message "Passenger
air bag deactivated" on the display.
If the passenger air bag is disarmed,
the warning light comes on when the
ignition is switched on and it remains
on.
Always consult a CITROËN dealer if
the warning light fl ashes.
Front and side air bags
warning light
This comes on for a few seconds when the ignition is
switched on.
With the engine running, illumination
of this warning light accompanied by
an audible signal and the message
"Air bag fault" on the multifunction
display, indicates a fault in the air
bags.
Consult a CITROËN dealer.
Coolant temperature indicator
- needle in zone (A) , the tempera-
ture is correct,
- needle in zone (B) , the tempera-
ture is too high. The central STOP
warning light fl ashes, accompanied by an audible signal and the
message "Engine coolant temp.
too high" on the display.
You must stop.
Consult a CITROËN dealer.
* According to country.
22 -
INSTRUMENT PANEL
After switching on the ignition, three
functions are shown in succession:
- service indicator,
- engine oil level indicator,
- total distance recorder/total and
trip distances.
Note : the total and trip distances are
displayed for 30 seconds when the
ignition is switched off, on opening
the driver's door, as well as on lock-
ing and unlocking the vehicle.
Service indicator
This is a visual reminder of when the
next service is due. This service is to
be carried out according to the manufacturer's servicing schedule.
Operation
As soon as the ignition is switched
on and for 5 seconds, the spanner
symbolising ''service operation'' is lit.
The trip recorder display shows the
distance remaining (in round fi gures)
before the next service.
Example: 4,800 miles/km remain be-
fore the next service is due. When the
ignition comes on and for 5 seconds
the display shows:
5 seconds after the ignition is
switched on, the total distance re-
corder resumes normal operation and
the display shows the total or trip dis-
tances.
The distance remaining before the next
service is less than 500 miles (1,000 km).
Example: 400 miles (900 km) remain
before the next service is due.
When switching on the ignition and
for 5 seconds, the display shows:
5 seconds after the ignition is
switched on, the total distance re-
corder resumes normal operation
and the symbol remains lit.
This indicates that a service should
be carried out shortly. The display
shows the total or trip distances.
The service is overdue.
Each time the ignition is switched on
and for 5 seconds, the symbol and
the excess distance fl ash.
Example: the service is overdue by
300 miles/km. The service should be
carried out very shortly.
When the ignition is switched on and
for 5 seconds, the display shows:
5 seconds after the ignition is
switched on, the total distance re-
corder resumes normal operation and
the symbol remains lit. The display
shows the total or trip distances.
Note: the spanner lights if the two-year
interval has been exceeded.
23
-
Resetting the service indicator
Your CITROËN dealer carries out
this operation after each service.
The reset procedure is as follows:
- Switch off the ignition.
- Press and hold button 1 .
- Switch on the ignition.
The display begins a 10 second count-
down.
-
Keep button 1 pressed for 10 seconds.
The display shows [=0] and the spanner
disappears.
Engine oil level indicator
When the ignition is switched on,
the engine oil level is indicated for
approximately 10 seconds, after the
service information.
Surplus of oil
Flashing of the six squares and displaying of "max" indicate a surplus of
oil which could damage the engine.
If the surplus of oil is confi rmed by
a check using the dipstick, contact a
CITROËN dealer without delay.
Lack of oil
Flashing of the six segments and displaying of "min" indicate a lack of oil
which could damage the engine.
If the lack of oil is confi rmed by a
check using the dipstick, it is essential
that the level is topped up.
Oil level indicator fault
Flashing of the six segments indi-
cates a malfunction of the oil level
indicator.
There is a risk of damage to the engine.
Consult a CITROËN dealer.
The level read on the dipstick or on
the indicator will only be correct if
the vehicle is on level ground and
the engine has been off for more
than 15 minutes.
24 -
LIGHTING RHEOSTAT
CLOCK
Total distance recorder
Briefl y pressing button 1 alternates
between the total and trip distance
displays.
To reset the trip recorder to zero,
when it is displayed press button 1
until zeros appear.
With the lights on, press the button
to vary the intensity of the lighting of
the instruments and controls. When
the lighting reaches the minimum (or
maximum) setting, release the button
then press it again to increase (or re-
duce) the brightness.
As soon as the lighting is of the re-
quired brightness, release the button.
Button 1 : hour adjustment
Button 2 : minute adjustment
Press and hold the button for rapid
advance.
25
-
DISPLAY A
This displays the following information:
- the time,
- the date,
- the audio system displays,
- a door check (e.g.: ''left front door
open''),
- warning messages (e.g. ''remote
control battery fl at'') or information
messages (e.g. ''economy mode
active''), displayed temporarily.
Adjusting the parameters display A
Press and hold button A for two sec-
onds to access the settings; the data
fl ashes, indicating it is ready to be
modifi ed.
Then, each press of button A scrolls
through the various data in the follow-
ing order:
- language of information displayed,
- hours (12 then 24 hour mode),
- minutes,
- year,
- month,
- day.
Pressing button B alters the value of
the parameter selected. Press and
hold for rapid advance (return to start
after the last possible value).
After 7 seconds with no action, the
standard display returns; the modifi ed
data is now recorded.
AUDIO EQUIPMENT
26 -
AUDIO RD3
Stalk movement Function
1 - Press (behind) Increase volume
2 - Press (behind) Decrease volume
1 + 2 - Simultaneous press Sound cut-off (mute); restoring of the sound by pressing any button
3 - Press Automatic search of higher frequencies (radio) -Selection of the next track (CD)
4 - Press Automatic search of lower frequencies (radio) - Selection of the previous track (CD)
5 - Press the end Change of source (radio/CD)
6 - Rotation (clockwise) Selection of next station stored in memory (radio)
7 - Rotation (anti-clockwise) Selection of previous station stored in memory (radio)
27
AUDIO EQUIPMENT
-
Button Function
A Radio on/off.
B - Decrease volume.
C + Increase volume.
D RDS
RDS function on/off.
Press for more than 2 seconds: regional following mode on/off.
E TA
Traffi c information priority on/off.
Press for more than 2 seconds: PTY function on/off.
H
Selection of bass, treble, loudness, sound distribution and automatic volume correction.
I
Increase the setting of the functions associated with button H.
J
Decrease the setting of the functions associated with button.
L
Manual and automatic search of higher frequency.
Selection of next CD track and PTY (radio).
M MAN Manual/automatic operation of buttons L and N.
N
Manual and automatic search of lower frequency.
Selection of previous CD track and PTY (radio).
Q CD
Selection of CD.
Press for more than 2 seconds: shuffl e.
R Radio
Selection of radio. Selection of FM1, FM2, FMast and AM wavebands.
Press for more than 2 seconds: automatic storing of stations in memory (autostore).
S
Ejection of CD.
1 to 6 12 34 56
Selection of station stored in memory.
Press for more than 2 seconds: storing of a station in memory.
AUDIO EQUIPMENT
28 -
Adjusting the loudness
This function automatically empha-
sises bass and treble tones. Press
or J to switch the function on
or off.
On/off
With the ignition key
to switch the
set on or off.
The set can operate for 30 minutes
without the vehicle ignition being
switched on.
Anti-theft system
The audio system is coded in such a
way that it can operate only on your
vehicle. It would not function if fi tted
to another vehicle.
The anti-theft system is automatic
Adjusting the bass
Adjusting the treble
When
is displayed, press
or
J
to vary the setting.
for a minimum treble
setting,
for a normal setting,
for a maximum treble
setting.
several
times in succession
to access the bass
, treble
,
,
fader
, balance
and automatic
volume correction.
Exit from audio mode is automatic
volume correction.
bass and treble settings are
specifi c to each source. It is possi-
, CD
and CD
When
is dis-
or
J
to vary the setting.
for a
setting,
for a
for a maximum bass
setting.
Press button
to in-
to decrease it.
Continuous pressure on
and
allows
the volume.
GENERAL FUNCTIONS
ADJUSTING THE VOLUME
AUDIO SETTINGS
29
AUDIO EQUIPMENT
RADIO
Adjusting the front/rear sound
When
is displayed, press but-
ton
or
J
.
Button
increases the volume in the
front.
Button
J
increases the volume in the
Adjusting the right/left sound
When
is displayed, press but-
ton
or
J
.
Button
increases the volume on the
Button
J
increases the volume on the
Automatic volume correction
This function enables the volume to
on the level of noise produced by the
speed of the vehicle.
Press buttons
or
J
to switch the
function on or off.
Selecting radio mode
Press button
.
Notes on radio reception
Your car radio is subject to pheno-
of interference. This is no refl ection on
the quality of the equipment, but is due
to the nature of the signals and the
way in which they are transmitted.
On MW/LW, interference may be
voltage power lines or bridges, or in
tunnels.
sult of increasing distance from the
transmitter, defl ection of the signals by
Selecting a waveband
Briefl y press button
to select the
-
29
AUDIO EQUIPMENT
RADIO
Adjusting the front/rear sound
When
is displayed, press but-
ton
or
J
.
Button
increases the volume in the
front.
Button
J
increases the volume in the
Adjusting the right/left sound
When
is displayed, press but-
ton
or
J
.
Button
increases the volume on the
Button
J
increases the volume on the
Automatic volume correction
This function enables the volume to
on the level of noise produced by the
speed of the vehicle.
Press buttons
or
J
to switch the
function on or off.
Selecting radio mode
Press button
.
Notes on radio reception
Your car radio is subject to pheno-
of interference. This is no refl ection on
the quality of the equipment, but is due
to the nature of the signals and the
way in which they are transmitted.
On MW/LW, interference may be
voltage power lines or bridges, or in
tunnels.
sult of increasing distance from the
transmitter, defl ection of the signals by
Selecting a waveband
Briefl y press button
to select the
-
AUDIO EQUIPMENT
30 -
Briefl y press button
or
to search
for the station immediately above or
will obtain continuous scrolling of the
frequency.
The scrolling stops at the fi rst sta-
tion found as soon as the button is
If the
traffi c information pro-
gramme is selected, only stations
Searching for a station occurs fi rst in
sensitivity (selection of the most
sensitivity (selection of the weakest
To make a direct search in
sen-
sitivity, press button
or
twice.
Manual station search
Press the
button.
Briefl y press button
or
to in-
By continuing to press the button in
the direction selected, you will obtain
The scrolling stops at the fi rst sta-
tion found as soon as the button is
Pressing the
button again
search.
Manual storing of stations in the
Select the station required.
Press one of the buttons
to
for more than two seconds.
The sound stops then becomes audible
Automatic station search
Automatic storing of FM stations
Press and hold but-
ton
for more than
two seconds.
Your radio automatically stores the
. These stations are stored in the
If it is not possible to fi nd 6 stations,
the remaining memories are empty.
Recalling stations stored in the
For each waveband, briefl y press
to
to recall the cor-
31
AUDIO EQUIPMENT
RDS
Traffi c information programme
Regional following mode (REG)
RDS station following
The display indicates the name of the
station selected. The radio is conti-
transmitting the same programme.
Press the
button
to switch the function
on or off.
The multi-function display will show:
if the function is selected,
if the function is selected
Any traffi c information fl ash will be
given priority, whatever source you
If you wish to interrupt a message,
button; this switches
the function off.
Briefl y press the
button to
switch the function on
or off.
The multi-function display will show:
if the function is selected.
if the function is selected
When they are part
of a network, certain
stations broadcast re-
gional programmes in
the various areas they serve. With re-
gional following mode you can keep
Press the
button for more
than two seconds to switch the
function on or off.
Using the RDS (Radio Data
Radio Data System allows you to
tion, whatever frequency it is using
for the region you are going through.
tion announcements is indepen-
the volume button. The setting will
the next messages are broadcast.
-
AUDIO EQUIPMENT
32 -
EON system
This connects stations which are part
of the same network. It enables the
station that is part of the same net-
work as the station to which you are
This service is available when you have
selected the
traffi c information pro-
gramme or the
function.
PTY function
This allows you to listen to stations broad-
To search for a
programme:
With
selected,
but-
ton for more than two
seconds to switch this
function on or off.
select the
function,
briefl y press button
or
to
scroll down the list of the various
types of programmes offered.
when the programme of your
or
pressed for more than two
seconds to carry out an automatic
search (after an automatic search
the
function is switched off).
mode the different types of
to
for more
than two seconds. Briefl y press the
type of programme stored in the
Loading...