Cisco SOHO User Manual

Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
This document provides international regulatory and safety compliance information for Cisco 800 series routers and Cisco SOHO routers. Use this document with the other publications for the Cisco 800 series or Cisco SOHO series router you have purchased.
Safety, page 1
Electromagnetic Compatibility, page 3
EMC Class A Notices and Warnings, page 6

Safety

Telecommunications, page 7
Radio, page 10
Declarations of Conformity, page 16
Conformité Européenne (CE) Marking Directive, page 16
European Union Statements, page 16
California Perchlorate Contamination Prevention Act (Title 22, California Code of Regulations,
Chapter 33), page 17
Translated Safety Warnings, page 17
Obtaining Documentation and Submitting a Service Request, page 58
This section describes safety conditions and operating conditions for the Cisco 800 series routers and Cisco SOHO routers. It contains the following:
Agency Approvals and Standards
Operating Conditions for Canada
Operating Conditions for the European Community
Operating Conditions for the United Kingdom
Americas Headquarters: Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Safety
Power Cable and AC Adapter

Agency Approvals and Standards

The following safety standards apply to the Cisco 800 series routers and to the Cisco SOHO series routers:
UL 60950-1
CSA 60950-1
EN 60950-1
IEC 60950-1
AS/NZS 60950
CCC
NOM-019

Operating Conditions for Canada

In addition to the warnings and safety guidelines listed in the “Translated Safety Warnings” section on
page 17, the following operating condition applies to routers used in Canada:
The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational, and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements documents. The Department does not guarantee the equipment will operate to the user’s satisfaction.
Before installing the equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations.
Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions may give the telecommunications company cause to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas.
Caution Users should not attempt to make such connections themselves, but should contact the appropriate
electric inspection authority, or electrician, as appropriate.

Operating Conditions for the European Community

The warnings and safety guidelines listed in the “Translated Safety Warnings” section on page 17 apply to routers used in the European Community.
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
2
OL-10260-02

Operating Conditions for the United Kingdom

In addition to the warnings and safety guidelines listed in the “Translated Safety Warnings” section on
page 17, the following warnings apply to routers used in the United Kingdom:
Interconnection directly, or by way of other apparatus, of ports marked:
“Safety Warning—See instructions for use”
with ports marked or not so marked may produce hazardous conditions on the network, and that advice should be obtained from a competent engineer before such a connection is made.
The ports marked “Ethernet” and “Console” have a safety warning applied to them as follows:
“These ports do not provide isolation sufficient to satisfy the requirement of EN 41003; apparatus connected to these ports should either have been approved to EN 41003 or have previously been evaluated against B5E301 British Telecommunications plc (Post Office) Technical Guides 2 or 26 and given permission to attach; any other usage will invalidate any approval given to this apparatus.”
Other usage will invalidate any approval given to this apparatus if as a result it ceases to comply with EN 41003:1993.
This apparatus must be connected to a main socket outlet with a protective earth contact.
Connection of power supply: The router is intended for use when supplied with power from a supply
providing 100 to 250 VAC, 50 to 60 Hz up to 0.5A.

Electromagnetic Compatibility

Power Cable and AC Adapter

Warning
When installing the product, please use the provided or designated connection cables/power cables/AC adaptors. Using any other cables/adaptors could cause a malfunction or a fire. Electrical Appliance and Material Safety Law prohibits the use of UL-certified cables (that have the “UL” shown on the code) for any other electrical devices than products designated by CISCO. The use of cables that are certified by Electrical Appliance and Material Safety Law (that have “PSE” shown on the code) is not limited to CISCO-designated products. Statement 371.
Electromagnetic Compatibility
This section describes electromagnetic compatibility (EMC) compliance conditions for the Cisco 800 series routers and Cisco SOHO routers. It contains the following:
Agency Approvals and Standards
FCC Class B Statement
OL-10260-02
CISPR 22 Class B Statement
Canada Compliance Statements
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
3
Electromagnetic Compatibility
Australia Compliance Statement
Statement 157—VCCI Compliance for Class B Equipment

Agency Approvals and Standards

This section lists the following agency approvals and standards for EMC:
CFR47 part 15 subpart B, 2000 class B
EN55022, 1998 class B, CISPR22, 1997 class B
EN55024, 1998 Immunity Std, CISPR24, 1997 Immunity Std
EN61000-3-2, Harmonics, EN61000-3-3, Flicker
EN61000-4-2, Electro Static Discharge
EN61000-4-3, Radiated Immunity
EN61000-4-4, Electrical Fast Transients
EN61000-4-5, Surge
EN61000-4-6, Conducted Immunity
EN61000-4-11, Dips and Sags
AS/NZS 3548
CCC

FCC Class B Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna
Increase the separation between the equipment and the receiver
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
Caution Modification of this equipment without Cisco’s authorization may result in this equipment no longer
complying with FCC requirements for Class B digital devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television communications at your own expense.
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
4
OL-10260-02

CISPR 22 Class B Statement

Emissions:
This equipment complies with the requirements of CISPR 22 (EN 55022) for Class B Information Technology Equipment (ITE).

Canada Compliance Statements

Canadian Class B Statement

This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the interference-causing equipment standard entitled “Digital Apparatus,” ICES-003 of the Department of Communications.
Cet appareil numérique respecte les limites de bruits radioelectriques applicables aux appareils numériques de Classe B prescrites dans la norme sur le materiel brouilleur: “Appareils Numériques,” NMB-003 edictée par le ministre des Communications.
Electromagnetic Compatibility

Industry Canada Notice

This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is confirmed by the registration number. The abbreviation, IC, before the registration number signifies that registration was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. It does not imply that Industry Canada approved the equipment.

Australia Compliance Statement

Network connected equipment is approved to the Australian and New Zealand Safety and EMC requirements by Cisco Systems Incorporated which is a Recognized Laboratory by ACA and New Zealand. Stand-alone power supply modules provided with this equipment are separately approved by an Australian State designated Electricity Authority.
OL-10260-02
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
5

EMC Class A Notices and Warnings

Statement 157—VCCI Compliance for Class B Equipment
Warning
This is a Class B product based on the standard of the Voluntary Control Council for Interference from Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the instruction manual.
EMC Class A Notices and Warnings
This section includes the following EMC Class A warnings for Cisco 888 and IAD881 models:
Class A Notice for FCC
CISPR 22 Class A Statement
Canadian Class A Statement
Statement 191—VCCI Class A Warning for Japan

Class A Notice for FCC

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
Warning
Modification of this equipment without Cisco's authorization may result in this equipment no longer complying with FCC requirements for Class A digital devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television communications at your own expense.
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
6
OL-10260-02

CISPR 22 Class A Statement

This equipment complies with the requirements of CISPR 22 (EN 55022) for Class A Information Technology Equipment (ITE).

Telecommunications

Warning
This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

Canadian Class A Statement

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus as set out in the interference-causing equipment standard entitled "Digital Apparatus," ICES-003 of the Department of Communications.
Cet appareil numerique respecte les limites de bruits radioelectriques applicables aux appareils numeriques de Classe A prescrites dans la norme sur le materiel brouilleur: "Appareils Numeriques," NMB-003 edictee par le ministre des Communications.
Statement 191—VCCI Class A Warning for Japan
Warning
This is a Class A product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance may arise. When such trouble occurs, the user may be required to take corrective actions.
Statement 340
Telecommunications
This section describes telecommunications compliance conditions for the Cisco 800 series routers and Cisco SOHO routers. It contains the following:
Agency Approvals and Standards
FCC Part 68 Notice
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
OL-10260-02
7
Telecommunications

Agency Approvals and Standards

This section lists the following agency approvals and standards for telecommunications:
FCC part 68 – TIA-968-A 2002, Addendum 3 2005
IC CS-03, issue 9 2004
R&TTE Directive 5/1999/EC, CTR3, TBR3
AS/ACIF S002, S003, S006, S031, S043, C559
IDA TS ISDN, TS ADSL
IS 6100
225-540-784, 225-540-788
ITU I.430, ITU G.991.2, ITU G.992.1
Table 1 lists the Cisco 800 series routers that are not Telecom regulated because they only have Ethernet
ports or are only for Europe.
Table 1 Cisco 800 Series Routers That Are Not Telecom Regulated
Models That Have Only Ethernet Ports Models That are for Europe Only
Cisco 806 Cisco 836
Cisco 831 Cisco 856
Cisco 851
Cisco 861
Cisco 871
Cisco 881
Cisco 881G
1. These routers comply with the European requirements of CTR3/TBR3.

FCC Part 68 Notice

This equipment complies with Part 68 of the FCC rules and the Technical Requirements for Connection to the Telephone Network published by ACTA. On the bottom of the this equipment is a label that contains, among other information, the product identifier US:5B1MFNA0013 or US:5B1DLO1B0144. If requested, this number must be provided to the telephone company.
If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. If advance notice is not practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.
The telephone company may make changes in its facilities, equipment, operation, or procedures that could affect the operation of this equipment. If this happens, the telephone company will provide advance notice in order for you to make the necessary modifications to maintain uninterrupted service.
1
If you have trouble with this equipment, please contact Cisco Systems for repair and warranty information. If the trouble is causing harm to the telephone network, the telephone company can request that you remove the equipment from the network until the problem is resolved.
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
8
OL-10260-02
Telecommunications
Normally, this equipment will be used in conjunction with FCC approved equipment that limits the Encoded Analog Content that provides the required Billing Protection.
The facility interface and service order codes for the Cisco 800 series and the SOHO series routers are shown in Table 2.
Table 2 Cisco 800 Series and Cisco SOHO Series Routers Facility Interface and
Service Order Codes
Port Type
Facility Interface Code
Service Order Code Jack Type
ISDN BRI S/T 02IS5 6.0N RJ-49C
ISDN BRI U 02IS5 6.0N RJ-49C
DSU 56K 04DU5-56 6.0N RJ-48S
ADSL Metallic RJ-11C
SHDSL Metallic RJ-14C
FXO 02LS2 None RJ-11C
FXO 02GS2 None RJ-21X
DID 02RV2.T AS.2 RJ-11C
Analog Modem 02LS2 None RJ-11C
Cisco 800 series and SOHO series routers bearing labeling identification number US:5B1MFNA0013 or US:5B1DLO1B0144, and Cisco 860 and 880 router models bearing labeling identification number US:5B1ISO1B0247 comply with the following requirement:
FCC Rules and Regulations 47 CFR Part 68
TIA/EIA/IS-968, Technical Criteria for Terminal Equipment to Prevent Harm to the Telephone
Network, July 2001, as adopted by the Administrative Council on Terminal Attachments (ACTA).
Cisco 801, 802, 803, 804, 805, 806, 811, 813, 815, 826, 827, 828, 831, 836, 837, 851, 856, 857, 858, 871, 877, and 878 routers, and Cisco SOHO 76, 77, 78, 91, 96, and 97 routers bearing labeling identification number US:5BMFMAM0013 or US:5B1DLO1B0144, and IAD881F, IAD881B, C881SRST, , 888, 888G, IAD888F, IAD888B, C888SRST, routers bearing labeling identification number US:5B1IS01B0247 comply with the following requirement:
FCC Rules and Regulations 47 CFR Part 68
TIA/EIA/IS-968, Technical Criteria for Terminal Equipment to Prevent Harm to the Telephone
Network, 2002, Addendum 3 2005, as adopted by the Administrative Council on Terminal Attachments (ACTA).
OL-10260-02
Cisco’s Supplier Declarations of Conformity are available online at:
http://wwwin-tools.cisco.com/cse/prdapp/jsp/ExternalSearch.jsp?selNavObjId=search|extSearch
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
9

Radio

Radio
This section describes radio compliance conditions for the Cisco 800 series routers and Cisco SOHO routers. It contains the following:
Agency Approval and Standards
Power Level Settings
Canadian Compliance Statement
Statement 287—Declaration of Conformity to R&TTE Directive 1999/5/EC for the European
Community, Switzerland, Norway, Iceland and Liechtenstein
RF Exposure
Guidelines for Operating Cisco Wireless Access Points in Japan
Administrative Rules for Cisco Wireless Devices in Taiwan

Agency Approval and Standards

The agency approvals and standards for 2.4 GHz radio are as follows:
CFR47 part 15.247
RSS-210 Rev 5
ETSI EN 300.328.1
ETSI EN301.489.1& .17
RFS-29
Japan Std 33a and Std 66
EN 300.328-1
EN 300.328-2
EN 301.489-1
EN 301.489-17
EN 60950-1
EN 50835
Caution The Part 15 radio device operates on a non-interference basis with other devices operating at this
frequency when using the integrated antennas. Any changes or modification to the product not expressly approved by Cisco could void the user’s authority to operate this device.
Note This equipment is intended to be used in all EU and EFTA countries. Outdoor use may be restricted to
certain frequencies and/or may require a license for operation. For more details, contact Cisco Corporate Compliance.
10
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
OL-10260-02

Power Level Settings

Table 3 lists the maximum power level settings permissible for the radio modules.
Table 3 Maximum Rated Power Output for the Radios
Maximum Power Setting (dBM)
Radio FCC ID
LDKXSNIACG13 19 17
MCL74487504 17 15 16
802.11b (2.4-GHz) 802.11g (2.4-GHz) 802.11n (2.4-GHz)

Canadian Compliance Statement

This Class B Digital apparatus meets all the requirements of the Canadian Interference-Causing Equipment Regulations.
Cet appareil numerique de la classe B respecte les exigences du Reglement sur le material broilleur du Canada.
Radio
This device complies with Class B Limits of Industry Canada. Operation is subject to the following two conditions:
This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause undesired
operation.
Cisco 2.4-GHz Access Points are certified to the requirements of RSS-210 for 2.4-GHz spread spectrum devices. The use of this device in a system operating either partially or completely outdoors may require the user to obtain a license for the system according to the Canadian regulations. For further information, contact your local Industry Canada office.
Statement 287—Declaration of Conformity to R&TTE Directive 1999/5/EC for the European Community, Switzerland, Norway, Iceland and Liechtenstein
This section contains compliance information relevant to the European Union and other countries that have implemented the EU Directive 1999/5/EC. The information is applicable starting November 1st, 2005, and will replace any previous compliance information released within the EU for these products.
The information contained in this section applies to the following wireless LAN products:
Single-Band (2.4-GHz) Models
Cisco 850 series and Cisco 870 series routers
OL-10260-02
English:
[Bulgarian]:
Cisco 860 series and Cisco 880 series routers
This equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
11
Radio
[Czech]:
Dansk
[Danish]:
Deutsch
[German]:
Eesti
[Estonian]:
Español
[Spanish]:
[Greek]:
Français
[French]:
Íslenska
[Icelandic]:
Italiano
[Italian]:
Latviski
[Latvian]:
Dette udstyr er i overensstemmelse med de væsentlige krav og andre relevante bestemmelser i Direktiv 1999/5/EF.
Dieses Gerät entspricht den grundlegenden Anforderungen und den weiteren entsprechenden Vorgaben der Richtlinie 1999/5/EU.
See seade vastab direktiivi 1999/5/EÜ olulistele nõuetele ja teistele asjakohastele sätetele.
Este equipo cumple con los requisitos esenciales asi como con otras disposiciones de la Directiva 1999/5/CE.
Cet appareil est conforme aux exigences essentielles et aux autres dispositions pertinentes de la Directive 1999/5/EC.
Þetta tæki er samkvæmt grunnkröfum og öðrum viðeigandi ákvæðum Tilskipunar 1999/5/EC.
Questo apparato é conforme ai requisiti essenziali ed agli altri principi sanciti dalla Direttiva 1999/5/CE.
[Lithuanian]:
Nederlands
[Hungarian]:
[Norwegian]:
Português
[Portuguese]:
12
Dit apparaat voldoet aan de essentiele eisen en andere van toepassing zijnde bepalingen van de
[Dutch]:
[Maltese]:
Magyar
Norsk
Richtlijn 1999/5/EC.
Malti
Dette utstyret er i samsvar med de grunnleggende krav og andre relevante bestemmelser i EU-direktiv 1999/5/EF.
Polski
[Polish]:
Este equipamento está em conformidade com os requisitos essenciais e outras provisões relevantes da Directiva 1999/5/EC.
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
OL-10260-02
Radio
[Romanian]:
Slovensko
[Slovenian]:
Slovensky
[Slovak]:
Suomi
[Finnish]:
Svenska
[Swedish]:

RF Exposure

Acest echipament este in conformitate cu cerintele esentiale si cu alte prevederi relevante ale Directivei 1999/5/EC.
Ta naprava je skladna z bistvenimi zahtevami in ostalimi relevantnimi pogoji Direktive 1999/5/EC.
Toto zariadenie je v zhode so základnými požiadavkami a inými príslušnými nariadeniami direktív: 1999/5/EC.
The radio has been found to be compliant to the requirements set forth in CFR 47 Sections 2.1091, and
15.247 (b) (4) addressing RF Exposure from radio frequency devices as defined in Evaluating Compliance with FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields. The equipment should be installed more than 20 cm (7.9 in.) from your body or nearby persons. The access point must be installed to maintain a minimum 20 cm (7.9 in.) co-located separation distance from other FCC approved indoor/outdoor antennas used with the access point. Any antennas or transmitters not approved by the FCC cannot be co-located with the access point. The access point’s co-located 2.4 GHz integrated antennas support a minimum separation distance of 8 cm (3.2 in.) and are compliant with the applicable FCC RF exposure limit when transmitting simultaneously.
Note Dual antennas used for diversity operation are not considered co-located.

Guidelines for Operating Cisco Wireless Access Points in Japan

This section provides guidelines for avoiding interference when operating Cisco wireless access points in Japan. These guidelines are provided in both English and Japanese.
English Translation
This equipment operates in the same frequency bandwidth as industrial, scientific, and medical devices such as microwave ovens and mobile object identification (RF-ID) systems (licensed premises radio stations and unlicensed specified low-power radio stations) used in factory production lines.
1. 1. Before using this equipment, make sure that no premises radio stations or specified low-power
radio stations of RF-ID are used in the vicinity.
2. If this equipment causes RF interference to a premises radio station of RF-ID, promptly change the
frequency or stop using the device; contact the number below and ask for recommendations on avoiding radio interference, such as setting partitions.
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
OL-10260-02
13
Radio
3. If this equipment causes RF interference to a specified low-power radio station of RF-ID, contact
the number below.
Contact Number: 03-5549-6500
Japanese Translation
03-6434-6500

Administrative Rules for Cisco Wireless Devices in Taiwan

This section provides administrative rules for operating Cisco wireless access products in Taiwan. The rules are provided in both Chinese and English.

Wireless Devices with IEEE 802.11b/g Radios

Chinese Translation
English Translation
This equipment is limited for indoor use.
43768
14
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
OL-10260-02

All Access Wireless Products

Chinese Translation
Radio
OL-10260-02
English Translation
Administrative Rules for Low-Power Radio-Frequency Devices
Article 12
For those low-power radio-frequency devices that have already received a type-approval, companies, business units, or users should not change its frequencies, increase its power, or change its original features and functions.
Article 14
The operation of the low-power radio-frequency devices is subject to the conditions that no harmful interference is caused to aviation safety and authorized radio stations; and if interference is caused, the user must stop operating the device immediately and can’t re-operate it until the harmful interference is clear.
The authorized radio station means a radio-communication service operating in accordance with the Communication Act.
The operation of the low-power radio-frequency devices is subject to the interference caused by the operation of an authorized radio station, by another intentional or unintentional radiator, by industrial, scientific and medical (ISM) equipment, or by an incidental radiator.
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
15

Declarations of Conformity

Declarations of Conformity
The Declaration of Conformity statements for this product can be found at the following URL:
http://www.ciscofax.com
Note If you still have questions regarding the compliance of these products or you cannot find the information
you are looking for, please send an e-mail request to complianceinfo@cisco.com.

Conformité Européenne (CE) Marking Directive

This product bears the CE mark in conformance with Annex VII of Directive 1999/5/CE.
The following CE mark and class-2 identifier is affixed to the equipment and packaging:

European Union Statements

The following statements apply to Cisco 801 routers and Cisco 803 routers used in the European Union (EU).
Network Termination Point Statement
ISDN S/T Ports Statement

Network Termination Point Statement

This product does not contain a “Network Termination Point” (NTP) as defined by ETSI 300 386-2. This product is classified by the manufacturer as “Terminal Equipment.” If you have any additional questions, please contact your local network operator.

ISDN S/T Ports Statement

These ports have not been classified as “directly connected ports” to outside cables as defined by CISPR 24, 1997 by the manufacturer. If you have any additional questions, please contact your local network operator.
16
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
OL-10260-02

California Perchlorate Contamination Prevention Act (Title 22, California Code of Regulations, Chapter 33)

California Perchlorate Contamination Prevention Act (Title 22, California Code of Regulations, Chapter 33)
The battery inside this product might contain perchlorate, a known hazardous substance, so special handling and disposal of this product might be necessary. For more information about perchlorate and best management practices for perchlorate-containing substances, see
http://www.dtsc.ca.gov/HazardousWaste/Perchlorate/index.cfm.

Translated Safety Warnings

This section contains the translations of the following warning statements. A warning means danger. You are in a situation that could cause bodily injury. Before working on equipment, be aware of the hazards involved with electrical circuitry and standard safety practices to prevent accidents.
Statement 1071—Warning Definition
Statement 12—Power Supply Disconnection Warning
Statement 19—TN Power Warning
Statement 23—ISDN Connection Warning
Statement 43—Jewelry Removal Warning
Statement 94—Wrist Strap Warning
Statement 119—Unit Short Circuit Protection
Statement 150—Power Off Before Working on System
Statement 151—ISDN Network Voltages Warning
Statement 162—EU Public Network Port Warning
Statement 199—Emergency Access Warning
Statement 242—Equipment Grounding Warning
Statement 245B—Explosive Device Proximity Wireless Network Device
Statement 332—Antenna Installation Warning
Statement 1001—Work During Lightning Activity
Statement 1004—Installation Instructions
Statement 1005—Circuit Breaker
Statement 1015—Battery Handling
Statement 1021—SELV Circuit
Statement 1023—No. 26 AWG
Statement 1024—Ground Conductor
Statement 1030—Equipment Installation
Statement 1035—Proximity to Water
OL-10260-02
Statement 1036—Telephone Jacks in Wet Locations
Statement 1037—Uninsulated Wires or Terminals
Statement 1038—Telephone Use During an Electrical Storm
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
17
Translated Safety Warnings
Statement 1040—Product Disposal
Statement 1042—Ring Signal Generator
Statement 1073—No User-Serviceable Parts
Statement 1074—Comply with Local and National Electrical Codes
Statement 1071—Warning Definition
Warning
Waarschuwing
Varoitus
IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device.
SAVE THESE INSTRUCTIONS
BELANGRIJKE VEILIGHEIDSINSTRUCTIES
Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt raadplegen.
BEWAAR DEZE INSTRUCTIES
TÄRKEITÄ TURVALLISUUSOHJEITA
Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien lausuntonumeroiden avulla.
18
SÄILYTÄ NÄMÄ OHJEET
Attention
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
IMPORTANTES INFORMATIONS DE SÉCURITÉ
Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil, référez-vous au numéro de l'instruction situé à la fin de chaque avertissement.
CONSERVEZ CES INFORMATIONS
OL-10260-02
Translated Safety Warnings
Warnung
Avvertenza
Advarsel
WICHTIGE SICHERHEITSHINWEISE
Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.
BEWAHREN SIE DIESE HINWEISE GUT AUF.
IMPORTANTI ISTRUZIONI SULLA SICUREZZA
Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti. Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le traduzioni delle avvertenze riportate in questo documento.
CONSERVARE QUESTE ISTRUZIONI
VIKTIGE SIKKERHETSINSTRUKSJONER
Dette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade på person. Før du begynner å arbeide med noe av utstyret, må du være oppmerksom på farene forbundet med elektriske kretser, og kjenne til standardprosedyrer for å forhindre ulykker. Bruk nummeret i slutten av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne enheten.
Aviso
¡Advertencia!
TA VARE PÅ DISSE INSTRUKSJONENE
INSTRUÇÕES IMPORTANTES DE SEGURANÇA
Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos perigos envolvidos no manuseio de circuitos elétricos e familiarize-se com as práticas habituais de prevenção de acidentes. Utilize o número da instrução fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham este dispositivo.
GUARDE ESTAS INSTRUÇÕES
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña a este dispositivo.
GUARDE ESTAS INSTRUCCIONES
OL-10260-02
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
19
Translated Safety Warnings
Varning!
VIKTIGA SÄKERHETSANVISNINGAR
Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada. Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och känna till vanliga förfaranden för att förebygga olyckor. Använd det nummer som finns i slutet av varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna anordning.
SPARA DESSA ANVISNINGAR
20
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
OL-10260-02
Translated Safety Warnings
Aviso
Advarsel
INSTRUÇÕES IMPORTANTES DE SEGURANÇA
Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham o dispositivo.
GUARDE ESTAS INSTRUÇÕES
VIGTIGE SIKKERHEDSANVISNINGER
Dette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for legemesbeskadigelse. Før du begynder arbejde på udstyr, skal du være opmærksom på de involverede risici, der er ved elektriske kredsløb, og du skal sætte dig ind i standardprocedurer til undgåelse af ulykker. Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de oversatte advarsler, der fulgte med denne enhed.
GEM DISSE ANVISNINGER
OL-10260-02
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
21
Translated Safety Warnings
22
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
OL-10260-02
Translated Safety Warnings
Statement 12—Power Supply Disconnection Warning
Warning
Waarschuwing
Varoitus
Attention
Warnung
Avvertenza
Before working on a chassis or working near power supplies, unplug the power cord on AC units; disconnect the power at the circuit breaker on DC units.
Voordat u aan een frame of in de nabijheid van voedingen werkt, dient u bij wisselstroom toestellen de stekker van het netsnoer uit het stopcontact te halen; voor gelijkstroom toestellen dient u de stroom uit te schakelen bij de stroomverbreker.
Kytke irti vaihtovirtalaitteiden virtajohto ja katkaise tasavirtalaitteiden virta suojakytkimellä, ennen kuin teet mitään asennuspohjalle tai työskentelet virtalähteiden läheisyydessä.
Avant de travailler sur un châssis ou à proximité d'une alimentation électrique, débrancher le cordon d'alimentation des unités en courant alternatif ; couper l'alimentation des unités en courant continu au niveau du disjoncteur.
Bevor Sie an einem Chassis oder in der Nähe von Netzgeräten arbeiten, ziehen Sie bei Wechselstromeinheiten das Netzkabel ab bzw. schalten Sie bei Gleichstromeinheiten den Strom am Unterbrecher ab.
Prima di lavorare su un telaio o intorno ad alimentatori, scollegare il cavo di alimentazione sulle unità CA; scollegare l'alimentazione all’interruttore automatico sulle unità CC.
OL-10260-02
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
23
Translated Safety Warnings
Advarsel
Aviso
¡Advertencia!
Varning!
Før det utføres arbeid på kabinettet eller det arbeides i nærheten av strømforsyningsenheter, skal strømledningen trekkes ut på vekselstrømsenheter og strømmen kobles fra ved strømbryteren på likestrømsenheter.
Antes de trabalhar num chassis, ou antes de trabalhar perto de unidades de fornecimento de energia, desligue o cabo de alimentação nas unidades de corrente alternada; desligue a corrente no disjuntor nas unidades de corrente contínua.
Antes de manipular el chasis de un equipo o trabajar cerca de una fuente de alimentación, desenchufar el cable de alimentación en los equipos de corriente alterna (CA); cortar la alimentación desde el interruptor automático en los equipos de corriente continua (CC).
I
nnan du arbetar med ett chassi eller nära strömförsörjningsenheter skall du för växelströmsenheter
dra ur nätsladden och för likströmsenheter bryta strömmen vid överspänningsskyddet.
Statement 19—TN Power Warning
Warning
Waarschuwing
Varoitus
Attention
Warnung
Avvertenza
Advarsel
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
24
The device is designed to work with TN power systems.
Het apparaat is ontworpen om te functioneren met TN energiesystemen.
Koje on suunniteltu toimimaan TN-sähkövoimajärjestelmien yhteydessä.
Ce dispositif a été conçu pour fonctionner avec des systèmes d'alimentation TN.
Das Gerät ist für die Verwendung mit TN-Stromsystemen ausgelegt.
Il dispositivo è stato progettato per l’uso con sistemi di alimentazione TN.
Utstyret er utfomet til bruk med TN-strømsystemer.
OL-10260-02
Translated Safety Warnings
Aviso
¡Advertencia!
Varning!
O dispositivo foi criado para operar com sistemas de corrente TN.
El equipo está diseñado para trabajar con sistemas de alimentación tipo TN.
Enheten är konstruerad för användning tillsammans med elkraftssystem av TN-typ.
Statement 23—ISDN Connection Warning
Warning
Waarschuwing
Varoitus
Attention
The ISDN connection is regarded as a source of voltage that should be inaccessible to user contact. Do not attempt to tamper with or open any public telephone operator (PTO)-provided equipment or connection hardware. Any hardwired connection (other than by a nonremovable, connect-one-time-only plug) must be made only by PTO staff or suitably trained engineers.
De verbinding met ISDN (Integrated Services Digital Network = Digitaal netwerk met geïntegreerde faciliteiten) wordt beschouwd als een spanningsbron die ontoegankelijk dient te zijn voor gebruikers. Gebruikers dienen geen poging te doen om door de openbare telefoondienst (PTT) verstrekte apparatuur of aansluitingshardware te openen of ermee te knoeien. Alle vastbedrade verbindingen (behalve die verbindingen die gemaakt zijn door een niet-verwijderbare, slechts eenmaal te verbinden stekker) dienen slechts door PTT-personeel of door daartoe opgeleide ingenieurs gemaakt te worden.
ISDN-liitäntää pidetään jännitelähteenä, jonka kanssa käyttäjän ei tulisi päästä kosketuksiin. Käyttäjien ei tulisi yrittää peukaloida tai avata laitteita tai liittimiä, jotka kuuluvat yleiselle puhelinlaitokselle (PTO). Ainoastaan yleisen puhelinlaitoksen henkilökunnan tai ammattitaitoisten teknikoiden tulee tehdä kaapeliliitännät (lukuun ottamatta kiinteitä pistokkeita, jotka yhdistetään ainoastaan yhden kerran).
La connexion du réseau numérique intégré (Integrated Services Digital Network ou ISDN) constitue une source de tension qui ne doit pas être accessible à l'utilisateur. Les utilisateurs ne doivent jamais tenter de modifier ni même d'ouvrir un matériel fourni par une compagnie de téléphone public, ou le matériel de connexion. Toute connexion câblée (autre que celles établies par une prise non démontable à connexion unique) ne doit être effectuée que par le personnel de la compagnie de téléphone ou par des techniciens proprement formés.
OL-10260-02
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
25
Translated Safety Warnings
Warnung
Avvertenza
Advarsel
Aviso
Die ISDN-Verbindung gilt als eine Spannungsquelle, die dem Anwender unzugänglich sein sollte. Anwender sollten nicht versuchen, sich an der von den Anbietern öffentlicher TK-Dienste gelieferten Ausstattung oder Verbindungs-Hardware zu schaffen zu machen oder sie zu öffnen. Alle festverdrahteten Verbindungen (mit Ausnahme der Verbindungen mit einem nicht abnehmbaren, nur einmal anzuschließenden Stecker) sind von Mitarbeitern des TK-Anbieters oder von entsprechend geschulten Technikern herzustellen.
Il collegamento ISDN (Integrated Services Digital Network - Rete digitale a servizi integrati) viene considerato come una fonte di tensione che dovrebbe essere inaccessibile al contatto dell’utente. Gli utenti non devono né manomettere né provare ad aprire le apparecchiature o i dispositivi di collegamento forniti dalla società telefonica. Qualsiasi collegamento cablato (ad eccezione di una spina non rimovibile, da installare una sola volta) deve essere eseguito esclusivamente da un dipendente della società telefonica o da tecnici specializzati.
ISDN-koblingen betraktes som en spenningskilde som bør være utilgjengelig for brukeren. Brukere bør ikke klusse med eller åpne utstyr eller tilkoblingsmateriale som er utstyrt av Telenor. Eventuelle faste installasjoner (bortsett fra koblinger som er foretatt med et støpsel for engangsbruk og som ikke kan fjernes) må kun utføres av Telenor-montører.
A conexão RDIS (Rede Digital com Integração de Serviços) é interpretada como uma fonte de tensão que deverá ser inacessível ao utilizador. Os utilizadores não deverão tentar violar qualquer equipamento ou conexão de serviço telefónico público. Qualquer conexão de rede de fios (para além daquela estabelecida por uma ficha não-removível de ligação única), deverá apenas ser efectuada por pessoal dos serviços telefónicos ou engenheiros devidamente treinados.
¡Advertencia!
Varning!
La conexión al circuito RDSI (Red Digital de Servicios Integrados) se considera como una fuente de voltaje con la cual el usuario no debe entrar en contacto. Los usuarios deberán evitar manipular indebidamente, o abrir, los equipos o hardware de conexión proporcionados por cualquier compañía operadora de la red pública de telefonía. Las conexiones de cable rígido que sean necesarias (excepto las de clavija no desmontable de un solo uso) deberán ser realizadas exclusivamente por personal de la entidad operadora de la red pública de telefonía, o por personal técnico adecuadamente capacitado.
ISDN-anslutningen betraktas som en spänningskälla och bör inte vara åtkomlig för användaren (ISDN: Integrated Services Digital Network = digitalt flertjänstnät). Användare får inte manipulera eller söka öppna utrustning eller anslutningsdon som tillhandahållits av telefonbolag (PTO-produkter). Anslutning av ledningar (med undantag av en icke löstagbar propp för engångsanslutning) får endast utföras av PTO-anställda eller lämpligt utbildade tekniker.
26
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
OL-10260-02
Statement 43—Jewelry Removal Warning
Translated Safety Warnings
Warning
Waarschuwing
Varoitus
Attention
Warnung
Avvertenza
Before working on equipment that is connected to power lines, remove jewelry (including rings, necklaces, and watches). Metal objects will heat up when connected to power and ground and can cause serious burns or weld the metal object to the terminals.
Alvorens aan apparatuur te werken die met elektrische leidingen is verbonden, sieraden (inclusief ringen, kettingen en horloges) verwijderen. Metalen voorwerpen worden warm wanneer ze met stroom en aarde zijn verbonden, en kunnen ernstige brandwonden veroorzaken of het metalen voorwerp aan de aansluitklemmen lassen.
Ennen kuin työskentelet voimavirtajohtoihin kytkettyjen laitteiden parissa, ota pois kaikki korut (sormukset, kaulakorut ja kellot mukaan lukien). Metalliesineet kuumenevat, kun ne ovat yhteydessä sähkövirran ja maan kanssa, ja ne voivat aiheuttaa vakavia palovammoja tai hitsata metalliesineet kiinni liitäntänapoihin.
Avant d’accéder à cet équipement connecté aux lignes électriques, ôter tout bijou (anneaux, colliers et montres compris). Lorsqu’ils sont branchés à l’alimentation et reliés à la terre, les objets métalliques chauffent, ce qui peut provoquer des blessures graves ou souder l’objet métallique aux bornes.
Vor der Arbeit an Geräten, die an das Netz angeschlossen sind, jeglichen Schmuck (einschließlich Ringe, Ketten und Uhren) abnehmen. Metallgegenstände erhitzen sich, wenn sie an das Netz und die Erde angeschlossen werden, und können schwere Verbrennungen verursachen oder an die Anschlußklemmen angeschweißt werden.
Prima di intervenire su apparecchiature collegate alle linee di alimentazione, togliersi qualsiasi monile (inclusi anelli, collane, braccialetti ed orologi). Gli oggetti metallici si riscaldano quando sono collegati tra punti di alimentazione e massa: possono causare ustioni gravi oppure il metallo può saldarsi ai terminali.
OL-10260-02
Advarsel
Fjern alle smykker (inkludert ringer, halskjeder og klokker) før du skal arbeide på utstyr som er koblet til kraftledninger. Metallgjenstander som er koblet til kraftledninger og jord blir svært varme og kan forårsake alvorlige brannskader eller smelte fast til polene.
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
27
Translated Safety Warnings
Aviso
¡Advertencia!
Varning!
Antes de trabalhar em equipamento que esteja ligado a linhas de corrente, retire todas as jóias que estiver a usar (incluindo anéis, fios e relógios). Os objectos metálicos aquecerão em contacto com a corrente e em contacto com a ligação à terra, podendo causar queimaduras graves ou ficarem soldados aos terminais.
Antes de operar sobre equipos conectados a líneas de alimentación, quitarse las joyas (incluidos anillos, collares y relojes). Los objetos de metal se calientan cuando se conectan a la alimentación y a tierra, lo que puede ocasionar quemaduras graves o que los objetos metálicos queden soldados a los bornes.
Tag av alla smycken (inklusive ringar, halsband och armbandsur) innan du arbetar på utrustning som är kopplad till kraftledningar. Metallobjekt hettas upp när de kopplas ihop med ström och jord och kan förorsaka allvarliga brännskador; metallobjekt kan också sammansvetsas med kontakterna.
Statement 94—Wrist Strap Warning
Warning
Waarschuwing
Varoitus
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
28
During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly touch the backplane with your hand or any metal tool, or you could shock yourself.
Draag tijdens deze procedure aardingspolsbanden om te vermijden dat de kaart beschadigd wordt door elektrostatische ontlading. Raak het achterbord niet rechtstreeks aan met uw hand of met een metalen werktuig, omdat u anders een elektrische schok zou kunnen oplopen.
Käytä tämän toimenpiteen aikana maadoitettuja rannesuojia estääksesi kortin vaurioitumisen sähköstaattisen purkauksen vuoksi. Älä kosketa taustalevyä suoraan kädelläsi tai metallisella työkalulla sähköiskuvaaran takia.
OL-10260-02
Translated Safety Warnings
Attention
Warnung
Avvertenza
Advarsel
Aviso
¡Advertencia!
Varning!
Lors de cette procédure, toujours porter des bracelets antistatiques pour éviter que des décharges électriques n’endommagent la carte. Pour éviter l’électrocution, ne pas toucher le fond de panier directement avec la main ni avec un outil métallique.
Zur Vermeidung einer Beschädigung der Karte durch elektrostatische Entladung während dieses Verfahrens ein Erdungsband am Handgelenk tragen. Bei Berührung der Rückwand mit der Hand oder einem metallenen Werkzeug besteht Elektroschockgefahr.
Durante questa procedura, indossare bracciali antistatici per evitare danni alla scheda causati da un’eventuale scarica elettrostatica. Non toccare direttamente il pannello delle connessioni, né con le mani né con un qualsiasi utensile metallico, perché esiste il pericolo di folgorazione.
Bruk jordingsarmbånd under prosedyren for å unngå ESD-skader på kortet. Unngå direkte berøring av bakplanet med hånden eller metallverktøy, slik at di ikke får elektrisk støt.
Durante este procedimento e para evitar danos ESD causados à placa, use fitas de ligação à terra para os pulsos. Para evitar o risco de choque eléctrico, não toque directamente na parte posterior com a mão ou com qualquer ferramenta metálica.
Usartiras conectadas a tierra en las muñecas durante este procedimiento para evitar daños en la tarjeta causados por descargas electrostáticas. No tocar el plano posterior con las manos ni con ninguna herramienta metálica, ya que podría producir un choque eléctrico.
Använd jordade armbandsremmar under denna procedur för att förhindra elektrostatisk skada på kortet. Rör inte vid baksidan med handen eller metallverktyg då detta kan orsaka elektrisk stöt.
OL-10260-02
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
29
Translated Safety Warnings
Statement 119—Unit Short Circuit Protection
Warning
Waarschuwing
Varoitus
Attention
Warnung
This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that a fuse or circuit breaker no larger than 120VAC, 20A U.S. (240VAC, 16 to 20A international) is used on the phase conductors (all current-carrying conductors). The fuse or circuit breaker must have adequate safety approvals recognized by the country of usage.
Dit product is afhankelijk van de installatie van het gebouw voor bescherming tegen kortsluiting (overstroom). Zorg ervoor dat de zekering of stroomonderbreker die gebruikt wordt niet groter is dan 120 V~, 20 ampère in de V.S. of 240 V~, 16-20 ampère internationaal op de fasegeleiders (alle stroomdragende geleiders). De zekering of stroomonderbreker dient de juiste veiligheidsgoedkeuringen te hebben in het land waarin het gebruikt wordt.
Tämä tuote on riippuvainen rakennuksen oikosulkusuojauksesta (ylivirtasuojauksesta). Varmista, että vaihejohtimissa (kaikissa jännitteellisissä johtimissa) käytetään alle 240 V vaihtovirran, 16–20 ampeerin (kansainvälinen) tai 120 V vaihtovirran, 20 ampeerin (Yhdysvallat) sulaketta tai virtakytkintä. Sulakkeessa tai virtakytkimessä on oltava käyttömaassa tunnistetut, riittävät turvahyväksynnät.
Pour la protection contre les courts-circuits (surtension), ce produit utilise les dispositifs intégrés au bâtiment. Assurez-vous qu'un fusible ou un disjoncteur est utilisé sur les conducteurs de phase (tous les conducteurs porteurs de courant). Le fusible ou le disjoncteur (maximum 240 V CA, 16 à 20 A [aux USA, maximum 120 V CA, 20 A]) doit être conforme aux normes de sécurité en vigueur dans votre pays.
Diese Produkt erfordert eine Gebäudeabsicherung gegen Kurzschluß (Überstrom). Achten Sie darauf, daß auf den Phasenleitern (allen stromführenden Leitern) eine Sicherung oder ein Schaltkreisunterbrecher verwendet wird, der nicht größer ist als 120VAC, 20A U.S. (240VAC, 16 bis 20A international). Die Sicherung oder der Schaltkreisunterbrecher muß angemessenen Sicherheitsvorschriften genügen, die den Bestimmungen des Anwendungslandes entsprechen.
30
Avvertenza
Advarsel
Aviso
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
La protezione di questo prodotto da cortocircuiti (sovracorrente) dipende dall'impianto elettrico dell’edificio. Assicuratevi che un fusibile o interruttore di circuito con meno di 120VAC, 20A U.S. (240VAC, da 16 a 20A internazionale) venga utilizzato sui conduttori di fase (tutti i conduttori di corrente elettrica). Il fusibile o interruttore di circuito deve rispondere alle specifiche di sicurezza invigore nel paese dove viene utilizzato.
Dette produktet er avhengig av bygningens installasjoner for overstrømsbeskyttelse (kortslutning). Kontroller at det ikke brukes en sikring eller overbelastningsbryter som er større enn 120 V, 20 ampere i USA, eller 240 V, 16 til 20 ampere internasjonalt, på faselederne (alle strømførende ledere). Sikringen eller overbelastningsbryteren må være sikkerhetsgodkjent i det aktuelle landet der den skal brukes.
Este dispositivo depende das instalações existentes para protecção contra curto-circuitos (sobrecarga). Assegure-se de que utiliza um fusível ou um disjuntor com uma capacidade não superior a 120VAC, 20A U.S. (240VAC, 16 a 20A internacional) nos condutores de fase (todos os condutores de corrente). O fusível ou disjuntor deverá possuir as necessárias aprovações de segurança por parte das autoridades locais.
OL-10260-02
Translated Safety Warnings
¡Advertencia!
Varning!
Este producto ha sido diseñado teniendo en cuenta que la instalación del edificio contará con protección contra cortocircuitos (sobrevoltajes). Asegúrese de que se usa un fusible o cortacircuitos no superior a 120VAC, 20A en los EE.UU. (240VAC, de 16 a 20A en el resto de países) en los conductores de fase (todos los conductores de transporte corriente). El fusible o cortacircuitos debe contar con las aprobaciones de seguridad adecuadas y reconocidas por el país en el que vayan a usarse.
Denna produkt förlitar sig på att byggnadens installation är försedd med skydd mot kortslutning (överström). Se till att en säkring eller ett överspänningsskydd för högst 120 V~, 20 A USA (240 V~, 16 – 20 A internationellt) används på fasledarna (alla strömförande ledare). Säkringen eller överspänningsskyddet måste ha fullgoda säkerhetstillstånd som erkänns av användningslandet.
Statement 150—Power Off Before Working on System
Warning
Waarschuwing
Before working on a system that has a standby/off switch, turn off the power by pressing the power switch to standby and unplug the power cord.
Alvorens aan een systeem met een standby/uit-schakelaar te werken dient u de voeding uit te schakelen door de voedingsschakelaar op standby te zetten en het voedingssnoer te verwijderen.
Varoitus
Attention
Warnung
Avvertenza
Advarsel
Aviso
¡Advertencia!
Varning!
Katkaise virta valmiustila/virtakytkimellä varustetusta laitteesta ennen sen käyttämistä painamalla virtakytkin valmiusasentoon ja irrottamalla sähköjohto.
Avant d'utiliser un système équipé d'un commutateur « Standby/Off » (pause/arrêt), coupez l'alimentation en plaçant le commutateur sur la position Standby et débranchez le cordon d'alimentation.
Bevor Sie an einem System mit einem Bereit-/Aus-Schalter arbeiten, stellen Sie den Strom ab, indem Sie den Stromschalter auf "Bereit" stellen und das Stromkabel herausziehen.
Prima di lavorare su un sistema con interruttore attesa/off, spegnetelo premendo il pulsante sulla posizione di attesa e staccate la spina elettrica.
Før det utføres arbeid på et system som har en standby/av-bryter, skal strømmen slås av ved å skyve av/på-bryteren til standby og trekke ut strømledningen.
Antes de começar a trabalhar num sistema com um interruptor standby (posição de espera)/off (desligado), desligue a corrente eléctrica colocando o interruptor na posição standby e retire o cabo de alimentação da tomada.
Antes de empezar a trabajar con un sistema cuyo interruptor incluya la posición standby, cierre la corriente posicionando el interruptor a standby y a continuación desconecte el cable eléctrico.
Innan du arbetar på ett system med en standby-/strömbrytaromkopplare, slå av strömmen genom att ställa omkopplaren på standby och koppla ur nätsladden.
OL-10260-02
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
31
Translated Safety Warnings
Statement 151—ISDN Network Voltages Warning
Warning
Waarschuwing
Varoitus
Attention
Warnung
Network hazardous voltages are present in the ISDN cable. If you detach the ISDN cable, detach the end away from the router first to avoid possible electric shock. Network hazardous voltages also are present on the system card in the area of the ISDN port (RJ-45 connector), regardless of when power is turned off (by pressing power switch to standby).
De ISDN-kabel bevat voltages die gevaar voor het netwerk opleveren. Als de ISDN-kabel verwijderd moet worden, verwijdert u om mogelijke elektrische schokken te vermijden eerst het uiteinde dat niet op de router is aangesloten. Verder bevat tevens de systeemkaart in de buurt van de ISDN-poort (RJ-45-aansluiting) voltages die gevaar voor het netwerk opleveren, onafhankelijk van wanneer de voeding wordt uitgeschakeld (door de voedingsschakelaar op standby te zetten).
ISDN-johdossa on verkolle vaarallisia jännitteitä. Jos ISDN-kaapeli irrotetaan, irrota ensin reitittimen puoleinen pää sähköiskun välttämiseksi. Verkolle vaarallisia jännitteitä on myös järjestelmäkortissa ISDN-portin alueella (RJ-45-liitin), vaikka virta olisikin katkaistu painamalla virtakytkin valmiusasentoon.
Des tensions électriques réseau dangereuses circulent sur le câble RNIS. Pour éviter tout risque de choc électrique lorsque vous débranchez ce câble, déconnectez d'abord l'extrémité non raccordée au routeur. Par ailleurs, des tensions dangereuses sont également présentes autour du port RNIS (connecteur RJ-45) de la carte système, que le système soit sous tension ou hors tension (commutateur d'alimentation sur « Standby »).
Auf dem ISDN-Kabel herrschen gefährliche Spannungen. Bei Entfernung des ISDN-Kabels muß zuerst das Kabel von der Routerseite her abgetrennt werden, um einen möglichen elektrischen Schlag zu vermeiden. Gefährliche Spannungen herrschen darüber hinaus auf der Systemkarte im Bereich des ISDN-Ports (RJ-45 Steckverbinder) und zwar unabhängig davon, ob der Strom (durch Umlegung des Stromschalters auf "Bereit") abgeschaltet ist.
32
Avvertenza
Advarsel
Aviso
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
Sono presenti dei voltaggi elettrici rete pericolosi nei cavi ISDN. Se staccate il cavo ISDN, dovete prima staccare l'estremità collegata al router per evitare scosse elettriche. Pericolose tensioni elettriche rete sono presente anche sulla scheda del sistema vicino alla porta ISDN (connettore RJ-45) a prescindere da quando sia stata spenta l'alimentazione elettrica (premendo il pulsante sulla posizione di attesa).
Livsfarlig spenning er til stede i nettverkets ISDN-kabel. Hvis du kobler fra ISDN-kabelen, skal enden som vender bort fra ruteren, kobles fra først for å unngå mulig elektrisk støt. Livsfarlig spenning er også til stede på nettverkets systemkort i området ved ISDN-utgangen (RJ-45-kobingen), uten hensyn til når strømmen er slått av (ved å skyve strømbryteren til standby).
Existem tensões de rede perigosas no cabo de Rede Digital com Integração de Serviços-RDIS (ISDN-Integrated Services Digital Network). Se for desligar o cabo RDIS, desligue primeiro a extremidade oposta à do comutador para evitar possíveis choques eléctricos. Existem tensões de rede perigosas também na placa do sistema, nomeadamente, na área da porta RDIS (conector RJ-45), independentemente do facto da corrente estar desligada (ao colocar o interruptor em standby) ou não.
OL-10260-02
Translated Safety Warnings
¡Advertencia!
Varning!
Las líneas RSDI contienen voltajes peligrosos de la red. Si desconecta el cable RSDI, separe primero el final del router para evitar posibles choques eléctricos. La tarjeta del sistema en el área del puerto RSDI (conector RJ-45) también contiene altos voltajes de la red, independientemente de si está apagada (posicionando el interruptor de la corriente a standby).
I ISDN-kabeln förekommer spänningar som är farliga för nätverk. Om du kopplar ur ISDN-kabeln, undvik eventuell elstöt genom att först koppla ur den ände som är längst bort ifrån routern. Spänningar som är farliga för nätverk förekommer också på systemkortet i området intill ISDN-porten (RJ-45-koppling), oberoende av när strömmen slås av (genom att ställa omkopplaren på standby).
Statement 162—EU Public Network Port Warning
Warning
Waarschuwing
If the symbol of suitability with an overlaid cross appears above a port, you must not connect the port to a public network that follows the European Union standards. Connecting the port to this type of public network can cause severe injury or damage your router.
Als er een geschiktheidsymbool met een overgetrokken kruis boven een poort aanwezig is, dan mag u deze poort niet op een openbaar netwerk aansluiten dat aan de normen van de Europese Unie voldoet. Als u de poort op een dergelijk openbaar netwerk aansluit, kan dit ernstig letsel of schade aan uw router-eenheid veroorzaken.
Varoitus
Attention
Warnung
Avvertenza
Advarsel
Aviso
Jos portin päälle ilmestyy soveltuvuussymboli, jonka päällä on rasti, porttia ei saa liittää Euroopan unionin standardien mukaiseen julkiseen verkkoon. Jos portti liitetään tällaiseen julkiseen verkkoon, seurauksena voi olla henkilö- tai reititinvaurio.
Pour éviter tout risque d'accident corporel et/ou de dommage matériel, si le symbole de capacité barré d'une croix apparaît au-dessus d'un port, il est vivement recommandé de ne pas connecter ce port à un réseau public aux normes de l'Union Européenne.
Wenn oberhalb des Ports das Verträglichkeitssymbol mit einem Kreuz darüber erscheint, dürfen Sie den Port nicht an ein öffentliches Netzwerk anschließen, daß den Standards der Europäischen Gemeinschaft folgt. Das Anschließen des Port an ein solches Netzwerk kann zu schweren Verletzungen führen oder Ihren Router beschädigen.
Se su una porta compare il simbolo di idoneità sbarrato, significa che la porta non può essere collegata a una rete pubblica a norma UE. Collegando la porta a un simile tipo di rete pubblica si possono correre seri rischi e provocare danni al proprio router.
Hvis symbolet for anvendelse med et kryss over vises over en utgang, skal utgangen ikke kobles til et offentlig nettverk som følger EU-standardene. Hvis utgangen kobles til denne typen offentlig nettverk, kan det medføre alvorlig personskade eller skade på ruteren.
Se o símbolo de adequação com uma cruz sobreposta aparecer acima de uma porta, não conectar a porta a uma rede pública que obedece aos padrões da União Europeia. A conexão da porta a este tipo de rede pública pode causar avarias ou danos severos ao seu distribuidor.
OL-10260-02
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
33
Translated Safety Warnings
¡Advertencia!
Varning!
Si aparece el símbolo de idoneidad con una cruz sobrepuesta encima de un puerto, no debe conectar el puerto a una red pública que siga los estándares de la Unión Europea. Si conecta el puerto a este tipo de red pública puede lesionarse o dañar su router.
Om lämplighetssymbolen med ett överlagt kors visas ovanför en port, får porten inte anslutas till ett offentligt nätverk av EU-standard. Om porten ansluts till denna typ av offentligt nätverk kan det förorsaka allvarlig personskada eller skada på routern.
Statement 199—Emergency Access Warning
Warning
Waarschuwing
Varoitus
This equipment is not designed for making emergency telephony calls when the power fails. Alternative arrangements should be made for access to emergency services. Access to emergency services can be affected by any call-barring function of this equipment.
Deze apparatuur is niet bedoeld voor noodtelefoongesprekken bij stroomstoringen. Voor telefoondiensten in noodsituaties moet u andere maatregelen treffen. Eventuele blokkeringsfuncties van deze apparatuur kunnen van invloed zijn op de bereikbaarheid van deze telefoondiensten.
Tätä laitetta ei voi käyttää hätäpuheluihin, jos sähkövirta on katkennut. Käytettävissä täytyy olla vaihtoehtoinen järjestelmä yhteyden saamiseksi hälytyskeskukseen. Hälytyskeskusyhteyden estymiseen voi vaikuttaa mikä tahansa tämän laitteiston soitonestotoiminto.
Attention
Warnung
Avvertenza
Advarsel
Aviso
Cet équipement n’est pas conçu pour les télécommunications d’urgence en cas de panne d’électricité et il importe de prévoir d'autres moyens d'accès aux services d'urgence. Cependant, toute fonction d'interdiction d'appel de cet équipement risque d'avoir une incidence sur l'accès aux services d'urgence.
Dieses Gerät ist nicht geeignet für Notruftelefonate, wenn die Stromzufuhr ausfällt. Für das Kontaktieren von Notfalldiensten sollten alternative Maßnahmen geplant werden. Das Kontaktieren von Notfalldiensten kann von jeder der anrufsperrenden Funktionen dieses Gerätes beeinträchtigt werden.
Questo apparecchio non è predisposto per effettuare chiamate d’emergenza nel caso dimancanza di alimentazione di corrente. È necessario pertanto predisporre misure alternative per consentire l’accesso ai servizi di emergenza. Tale accesso può essere inoltre influenzato dalle funzioni di blocco presenti sull’apparechio stesso.
Dette utstyret har ingen funksjon for nødtjenester når strømmen er brutt. En bør utarbeide alternative ordninger hvis man må ha tilgang til nødtjenester. Tilgangen til nødtjenester kan bli påvirket av alle samtalesperrende funksjoner i dette utstyret.
Este equipamento não foi concebido para estabelecer chamadas telefónicas de emergência quando faltar a energia. Devem tomar-se medidas alternativas para aceder a serviços de emergência. O acesso aos serviços de emergência pode ser afectado por qualquer função de barramento de chamadas aplicada a este equipamento.
34
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
OL-10260-02
Translated Safety Warnings
¡Advertencia!
Varning!
Este equipo no está diseñado para efectuar llamadas telefónicas de emergencia en caso de que falle la alimentación. Se deberán tomar medidas alternativas para acceder a servicios de emergencia. El acceso a servicios de emergencia puede verse afectado por cualquier función de bloqueo de llamadas que pueda tener este equipo.
Denna utrustning är inte utformad för telefonsamtal i nödläge när strömmen bryts. Andra arrangemang måste göras för att kunna nå nödtjänster. Åtkomst till nödtjänster kan påverkas av alla samtalsspärrningsfunktioner i denna utrustning.
Statement 242—Equipment Grounding Warning
Warning
Waarschuwing
Varoitus
This equipment needs to be grounded. Use a green and yellow 12 to 14 AWG ground wire to connect the host to earth ground during normal use.
Deze apparatuur hoort geaard te worden. Gebruik een groen/gele 12 - 14 AWG aarddraad om de host tijdens normaal gebruik met de aarde te verbinden.
Tämä laitteisto täytyy maadoittaa. Yhdistä isäntälaite maahan normaalikäytön aikana käyttämällä vihreä-keltaista 12 - 14 AWG -maadoitusjohtoa.
Statement 242
Attention
Warnung
Avvertenza
Advarsel
Aviso
¡Advertencia!
Varning!
Cet équipement doit être relié à la terre. Utilisez un fil vert et jaune de gabarit 12 à 14 (AWG) pour connecter l'hôte à la terre lors de son utilisation normale.
Dieses Gerät muß geerdet werden. Verwenden Sie ein grün/gelbes 12 bis 14-AWG-Erdungskabel, um damit das Host-Gerät während des normalen Betriebs zu erden.
Questa apparecchiatura deve essere collegata a massa. Durante l'uso normale, collegare l'host alla massa di terra usando un filo di massa verde e giallo di diametro compreso tra 12 e 14 AWG.
Dette utstyret krever jording. Bruk grønn og gul 12-14 AWG jordingsledning til å kople vertsterminalen til jording ved normal bruk.
É necessário que este equipamento esteja ligado à terra. Utilize um fio de ligação à terra de 12 a 14 AWG, verde e amarelo, para ligar o host à ligação à terra durante a sua utilização normal.
Este equipo debe conectarse a tierra. Utilizar un hilo de puesta a tierra entre 12 y 14 AWG verde y amarillo para conectar a tierra el equipo principal durante el uso normal.
Denna utrustning är avsedd att jordas. Använd en gulgrön jordledning av storlek 12 till 14 AWG till att jorda värdenheten vid normal användning.
Statement 245B—Explosive Device Proximity Wireless Network Device
OL-10260-02
This warning applies only to Cisco 850 series and Cisco 870 series routers.
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
35
Translated Safety Warnings
Warning
Waarschuwing
Varoitus
Attention
Warnung
Avvertenza
Advarsel
Aviso
Do not operate your wireless network device near unshielded blasting caps or in an explosive environment unless the device has been modified to be especially qualified for such use.
Gebruik dit draadloos netwerkapparaat alleen in de buurt van onbeschermde ontstekers of in een omgeving met explosieven indien het apparaat speciaal is aangepast om aan de eisen voor een dergelijk gebruik te voldoen.
Älä käytä johdotonta verkkolaitetta suojaamattomien räjäytysnallien läheisyydessä tai räjäytysalueella, jos laitetta ei ole erityisesti muunnettu sopivaksi sellaiseen käyttöön.
Ne jamais utiliser un équipement de réseau sans fil à proximité d'un détonateur non blindé ou dans un lieu présentant des risques d'explosion, sauf si l'équipement a été modifié à cet effet.
Benutzen Sie Ihr drahtloses Netzwerkgerät nicht in der Nähe ungeschützter Sprengkapseln oder anderer explosiver Stoffe, es sei denn, Ihr Gerät wurde eigens für diesen Gebrauch modifiziert und bestimmt.
Non utilizzare la periferica di rete senza fili in prossimità di un detonatore non protetto o di esplosivi a meno che la periferica non sia stata modificata a tale proposito.
Ikke bruk den trådløse nettverksenheten nært inntil uisolerte fenghetter eller i et eksplosivt miljø med mindre enheten er modifisert slik at den tåler slik bruk.
Não opere o dispositivo de rede sem fios perto de cápsulas explosivas não protegidas ou num ambiente explosivo, a não ser que o dispositivo tenha sido modificado para se qualificar especialmente para essa utilização.
¡Advertencia!
Varning!
No utilizar un aparato de la red sin cable cerca de un detonador que no esté protegido ni tampoco en un entorno explosivo a menos que el aparato haya sido modificado con ese fin.
Använd inte den trådlösa nätverksenheten i närheten av oskyddade tändhattar eller i en explosiv miljö om inte enheten modifierats för att kunna användas i sådana sammanhang.
Statement 332—Antenna Installation Warning
This warning applies only to Cisco 850 series and Cisco 870 series routers.
Warning
Waarschuwing
In order to comply with FCC radio frequency (RF) exposure limits, antennas should be located at a minimum of 7.9 inches (20 cm) or more from the body of all persons.
Om te voldoen aan de FCC radiofrequentie (RF) blootstellingslimieten dienen antennes zich minstens 20 cm of meer van de lichamen van alle personen bevinden.
36
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
OL-10260-02
Translated Safety Warnings
Varoitus
Attention
Warnung
Avvertenza
Advarsel
Aviso
¡Advertencia!
FCC:n antamien radiotaajuuksille altistumista koskevien rajoitusten mukaan antennien on sijaittava vähintään 20 cm:n päässä kaikista henkilöistä.
Pour se conformer aux limites d'exposition à la fréquence radio préconisées par la FCC (Federal Communications Commission), les antennes doivent se situer à un minimum de 20 cm de toute personne.
Um die in den FCC-Richtlinien festgelegten Expositionshöchstgrenzen für Radiofrequenzen (RF) nicht zu überschreiten, sollten Antennen mindestens 20 cm entfernt von Personen aufgestellt werden.
Per conformarsi ai limiti FCC di esposizione a radiofrequenza (RF), le antenne devono stare ad una distanza minima di 20 cm dal corpo di ogni persona.
I henhold til eksponeringsgrensene for radiofrekvenser (RF), skal antenner befinne seg på en avstand av minst 20 cm eller mer fra mennesker.
Para estar de acordo com as normas FCC de limites de exposição para freqüência de rádio (RF), as antenas devem estar distantes no mínimo 20 cm (7,9 pol) do corpo de qualquer pessoa.
Para cumplir con los límites de exposición de radio frecuencia (RF) de la Comisión Federal de Comunicaciones (FCC) es preciso ubicar las antenas a un mínimo de 20 cm (7,9 pulgadas) o más del cuerpo de las personas.
Varning!
För att följa FCC-exponeringsgränserna för radiofrekvens (RF), bör antenner placeras på minst 20 cm avstånd från alla människor.
Statement 1001—Work During Lightning Activity
Warning
Waarschuwing
Varoitus
Attention
Warnung
Avvertenza
Do not work on the system or connect or disconnect cables during periods of lightning activity.
Tijdens onweer dat gepaard gaat met bliksem, dient u niet aan het systeem te werken of kabels aan te sluiten of te ontkoppelen.
Älä työskentele järjestelmän parissa äläkä yhdistä tai irrota kaapeleita ukkosilmalla.
Ne pas travailler sur le système ni brancher ou débrancher les câbles pendant un orage.
Arbeiten Sie nicht am System und schließen Sie keine Kabel an bzw. trennen Sie keine ab, wenn es gewittert.
Non lavorare sul sistema o collegare oppure scollegare i cavi durante un temporale con fulmini.
OL-10260-02
Advarsel
Aviso
Utfør aldri arbeid på systemet, eller koble kabler til eller fra systemet når det tordner eller lyner.
Não trabalhe no sistema ou ligue e desligue cabos durante períodos de mau tempo (trovoada).
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
37
Translated Safety Warnings
¡Advertencia!
Varning!
No operar el sistema ni conectar o desconectar cables durante el transcurso de descargas eléctricas en la atmósfera.
Vid åska skall du aldrig utföra arbete på systemet eller ansluta eller koppla loss kablar.
Statement 1004—Installation Instructions
Warning
Waarschuwing
Varoitus
Attention
Warnung
Avvertenza
Advarsel
Aviso
¡Advertencia!
Varning!
Read the installation instructions before connecting the system to the power source.
Raadpleeg de installatie-instructies voordat u het systeem op de voedingsbron aansluit.
Lue asennusohjeet ennen järjestelmän yhdistämistä virtalähteeseen.
Avant de brancher le système sur la source d'alimentation, consulter les directives d'installation.
Vor dem Anschließen des Systems an die Stromquelle die Installationsanweisungen lesen.
Consultare le istruzioni di installazione prima di collegare il sistema all'alimentatore.
Les installasjonsinstruksjonene før systemet kobles til strømkilden.
Leia as instruções de instalação antes de ligar o sistema à fonte de energia.
Lea las instrucciones de instalación antes de conectar el sistema a la red de alimentación.
Läs installationsanvisningarna innan du kopplar systemet till strömförsörjningsenheten.
38
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
OL-10260-02
Statement 1005—Circuit Breaker
Translated Safety Warnings
Warning
Waarschuwing
Varoitus
Attention
Warnung
Avvertenza
This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: 120 VAC, 15A U.S. (240 VAC, 10A international)
Dit product is afhankelijk van de installatie van het gebouw voor beveiliging tegen kortsluiting (overstroom). Controleer of de beschermingsinrichting niet meer dan: 120 VAC, 15A U.S. (240 VAC, 10A international) is.
Tämä tuote on riippuvainen rakennukseen asennetusta oikosulkusuojauksesta (ylivirtasuojauksesta). Varmista, että suojalaitteen mitoitus ei ole yli: 120 VAC, 15A U.S. (240 VAC, 10A international)
Pour ce qui est de la protection contre les courts-circuits (surtension), ce produit dépend de l'installation électrique du local. Vérifiez que le courant nominal du dispositif de protection n'est pas supérieur à : 120 VAC, 15A U.S. (240 VAC, 10A international)
Dieses Produkt ist darauf angewiesen, dass im Gebäude ein Kurzschluss- bzw. Überstromschutz installiert ist. Stellen Sie sicher, dass der Nennwert der Schutzvorrichtung nicht mehr als: 120 VAC, 15A U.S. (240 VAC, 10A international) beträgt.
Questo prodotto dipende dall'impianto dell'edificio per quanto riguarda la protezione contro cortocircuiti (sovracorrente). Assicurarsi che il dispositivo di protezione non abbia un rating superiore a: 120 VAC, 15A U.S. (240 VAC, 10A international)
¡Advertencia!
OL-10260-02
Advarsel
Aviso
Dette produktet er avhengig av bygningens installasjoner av kortslutnings (overstrøm)-beskyttelse. Påse at verneenheten ikke er merket høyere enn: 120 VAC, 15A U.S. (240 VAC, 10A international)
Este produto depende das instalações existentes para proteção contra curto-circuito (sobrecarga). Assegure-se de que o fusível ou disjuntor não seja superior a: 120 VAC, 15A U.S. (240 VAC, 10A international)
Este equipo utiliza el sistema de protección contra cortocircuitos (o sobrecorrientes) del edificio. Asegúrese de que el dispositivo de protección no sea superior a: 120 VAC, 15A U.S. (240 VAC, 10A international)
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
39
Translated Safety Warnings
Varning!
Denna produkt är beroende av i byggnaden installerat kortslutningsskydd (överströmsskydd). Kontrollera att skyddsanordningen inte har högre märkvärde än: 120 VAC, 15A U.S. (240 VAC, 10A international)
120 VAC, 15A U.S. (240 VAC, 10A international)
120 VAC, 15A U.S. (240 VAC, 10A international)
120 VAC, 15A U.S. (240 VAC, 10A international)
120 VAC, 15A U.S. (240 VAC, 10A international)
Statement 1015—Battery Handling
Warning
Waarschuwing
Varoitus
Attention
Warnung
There is the danger of explosion if the battery is replaced incorrectly. Replace the battery only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions.
Er is ontploffingsgevaar als de batterij verkeerd vervangen wordt. Vervang de batterij slechts met hetzelfde of een equivalent type dat door de fabrikant aanbevolen is. Gebruikte batterijen dienen overeenkomstig fabrieksvoorschriften weggeworpen te worden.
Räjähdyksen vaara, jos akku on vaihdettu väärään akkuun. Käytä vaihtamiseen ainoastaan saman­tai vastaavantyyppistä akkua, joka on valmistajan suosittelema. Hävitä käytetyt akut valmistajan ohjeiden mukaan.
Danger d'explosion si la pile n'est pas remplacée correctement. Ne la remplacer que par une pile de type semblable ou équivalent, recommandée par le fabricant. Jeter les piles usagées conformément aux instructions du fabricant.
Bei Einsetzen einer falschen Batterie besteht Explosionsgefahr. Ersetzen Sie die Batterie nur durch den gleichen oder vom Hersteller empfohlenen Batterietyp. Entsorgen Sie die benutzten Batterien nach den Anweisungen des Herstellers.
Statement 1015
40
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
OL-10260-02
Translated Safety Warnings
Avvertenza
Advarsel
Aviso
¡Advertencia!
Varning!
Pericolo di esplosione se la batteria non è installata correttamente. Sostituire solo con una di tipo uguale o equivalente, consigliata dal produttore. Eliminare le batterie usate secondo le istruzioni del produttore.
Det kan være fare for eksplosjon hvis batteriet skiftes på feil måte. Skift kun med samme eller tilsvarende type som er anbefalt av produsenten. Kasser brukte batterier i henhold til produsentens instruksjoner.
Existe perigo de explosão se a bateria for substituída incorrectamente. Substitua a bateria por uma bateria igual ou de um tipo equivalente recomendado pelo fabricante. Destrua as baterias usadas conforme as instruções do fabricante.
Existe peligro de explosión si la batería se reemplaza de manera incorrecta. Reemplazar la batería exclusivamente con el mismo tipo o el equivalente recomendado por el fabricante. Desechar las baterías gastadas según las instrucciones del fabricante.
Explosionsfara vid felaktigt batteribyte. Ersätt endast batteriet med samma batterityp som rekommenderas av tillverkaren eller motsvarande. Följ tillverkarens anvisningar vid kassering av använda batterier.
OL-10260-02
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
41
Translated Safety Warnings
Statement 1021—SELV Circuit
Warning
Waarschuwing
Varoitus
Attention
Warnung
To avoid electric shock, do not connect safety extra-low voltage (SELV) circuits to telephone-network voltage (TNV) circuits. LAN ports contain SELV circuits, and WAN ports contain TNV circuits. Some LAN and WAN ports both use RJ-45 connectors. Use caution when connecting cables.
Om elektrische schokken te vermijden, mogen veiligheidscircuits met extra lage spanning (genaamd SELV = Safety Extra-Low Voltage) niet met telefoonnetwerkspanning (TNV) circuits verbonden worden. LAN (Lokaal netwerk) poorten bevatten SELV circuits en WAN (Regionaal netwerk) poorten bevatten TNV circuits. Sommige LAN en WAN poorten gebruiken allebei RJ-45 connectors. Ga voorzichtig te werk wanneer u kabels verbindt.
Jotta vältyt sähköiskulta, älä kytke pienjännitteisiä SELV-suojapiirejä puhelinverkkojännitettä (TNV) käyttäviin virtapiireihin. LAN-portit sisältävät SELV-piirejä ja WAN-portit puhelinverkkojännitettä käyttäviä piirejä. Osa sekä LAN- että WAN-porteista käyttää RJ-45-liittimiä. Ole varovainen kytkiessäsi kaapeleita.
Pour éviter une électrocution, ne raccordez pas les circuits de sécurité basse tension (Safety Extra-Low Voltage ou SELV) à des circuits de tension de réseau téléphonique (Telephone Network Voltage ou TNV). Les ports du réseau local (LAN) contiennent des circuits SELV et les ports du réseau longue distance (WAN) sont munis de circuits TNV. Certains ports LAN et WAN utilisent des connecteurs RJ-45. Raccordez les câbles en prenant toutes les précautions nécessaires.
Zur Vermeidung von Elektroschock die Sicherheits-Kleinspannungs-Stromkreise (SELV-Kreise) nicht an Fernsprechnetzspannungs-Stromkreise (TNV-Kreise) anschließen. LAN-Ports enthalten SELV-Kreise, und WAN-Ports enthalten TNV-Kreise. Einige LAN- und WAN-Ports verwenden auch RJ-45-Steckverbinder. Vorsicht beim Anschließen von Kabeln.
42
Avvertenza
Advarsel
Aviso
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
Per evitare scosse elettriche, non collegare circuiti di sicurezza a tensione molto bassa (SELV) ai circuiti a tensione di rete telefonica (TNV). Le porte LAN contengono circuiti SELV e le porte WAN contengono circuiti TNV. Alcune porte LAN e WAN fanno uso di connettori RJ-45. Fare attenzione quando si collegano cavi.
Unngå å koble lavspenningskretser (SELV) til kretser for telenettspenning (TNV), slik at du unngår elektrisk støt. LAN-utganger inneholder SELV-kretser og WAN-utganger inneholder TNV-kretser. Det finnes både LAN-utganger og WAN-utganger som bruker RJ-45-kontakter. Vær forsiktig når du kobler kabler.
Para evitar choques eléctricos, não conecte os circuitos de segurança de baixa tensão (SELV) aos circuitos de tensão de rede telefónica (TNV). As portas LAN contêm circuitos SELV e as portas WAN contêm circuitos TNV. Algumas portas LAN e WAN usam conectores RJ-45. Tenha o devido cuidado ao conectar os cabos.
OL-10260-02
Translated Safety Warnings
¡Advertencia!
Varning!
Para evitar la sacudida eléctrica, no conectar circuitos de seguridad de voltaje muy bajo (safety extra-low voltage = SELV) con circuitos de voltaje de red telefónica (telephone network voltage = TNV). Los puertos de redes de área local (local area network = LAN) contienen circuitos SELV, y los puertos de redes de área extendida (wide area network = WAN) contienen circuitos TNV. En algunos casos, tanto los puertos LAN como los WAN usan conectores RJ-45. Proceda con precaución al conectar los cables.
För att undvika elektriska stötar, koppla inte säkerhetskretsar med extra låg spänning (SELV-kretsar) till kretsar med telefonnätspänning (TNV-kretsar). LAN-portar innehåller SELV-kretsar och WAN-portar innehåller TNV-kretsar. Vissa LAN- och WAN-portar är försedda med RJ-45-kontakter. Iaktta försiktighet vid anslutning av kablar.
Statement 1023—No. 26 AWG
Warning
Waarschuwing
Varoitus
Attention
OL-10260-02
To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord.
Om brandgevaar te reduceren, dient slechts telecommunicatielijnsnoer nr. 26 AWG of groter gebruikt te worden.
Tulipalovaaran vähentämiseksi käytä ainoastaan nro 26 AWG- tai paksumpaa tietoliikennejohdinta.
Pour réduire le risque d’incendie, n’utiliser que des cordons de lignes de télécommunications de type AWG nº 26 ou plus larges.
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
43
Translated Safety Warnings
Warnung
Avvertenza
Advarsel
Aviso
Advertencia
Varning!
Zur Reduzierung der Feuergefahr eine Fernmeldeleitungsschnur der Größe 26 AWG oder größer verwenden.
Per ridurre il rischio di incendio, usare solo un cavo per linea di telecomunicazioni di sezione 0,12 mm
2
(26 AWG) o maggiore.
Bruk kun AWG nr. 26 eller telekommunikasjonsledninger med større dimensjon for å redusere faren for brann.
Para reduzir o risco de incêndio, utilize apenas terminais de fio de telecomunicações Nº. 26 AWG ou superiores.
Para reducir el riesgo de incendios, usar sólo líneas de telecomunicaciones de calibre No. 26 AWG o más gruesas.
För att minska brandrisken skall endast Nr. 26 AWG eller större telekommunikationsledning användas.
Statement 1024—Ground Conductor
Warning
Waarschuwing
Varoitus
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
44
This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available.
Deze apparatuur dient geaard te zijn. De aardingsleiding mag nooit buiten werking worden gesteld en de apparatuur mag nooit bediend worden zonder dat er een op de juiste wijze geïnstalleerde aardingsleiding aanwezig is. Neem contact op met de bevoegde instantie voor elektrische inspecties of met een elektricien als u er niet zeker van bent dat er voor passende aarding gezorgd is.
Laitteiden on oltava maadoitettuja. Älä koskaan ohita maajohdinta tai käytä laitteita ilman oikein asennettua maajohdinta. Ota yhteys sähkötarkastusviranomaiseen tai sähköasentajaan, jos olet epävarma maadoituksen sopivuudesta.
Statement 1024
OL-10260-02
Translated Safety Warnings
Attention
Warnung
Avvertenza
Advarsel
Aviso
¡Advertencia!
Cet équipement doit être mis à la masse. Ne jamais rendre inopérant le conducteur de masse ni utiliser l'équipement sans un conducteur de masse adéquatement installé. En cas de doute sur la mise à la masse appropriée disponible, s'adresser à l'organisme responsable de la sécurité électrique ou à un électricien.
Dieses Gerät muss geerdet sein. Auf keinen Fall den Erdungsleiter unwirksam machen oder das Gerät ohne einen sachgerecht installierten Erdungsleiter verwenden. Wenn Sie sich nicht sicher sind, ob eine sachgerechte Erdung vorhanden ist, wenden Sie sich an die zuständige Inspektionsbehörde oder einen Elektriker.
Questa apparecchiatura deve essere dotata di messa a terra. Non escludere mai il conduttore di protezione né usare l'apparecchiatura in assenza di un conduttore di protezione installato in modo corretto. Se non si è certi della disponibilità di un adeguato collegamento di messa a terra, richiedere un controllo elettrico presso le autorità competenti o rivolgersi a un elettricista.
Dette utstyret må jordes. Omgå aldri jordingslederen og bruk aldri utstyret uten riktig montert jordingsleder. Ta kontakt med fagfolk innen elektrisk inspeksjon eller med en elektriker hvis du er usikker på om det finnes velegnet jordning.
Este equipamento deve ser aterrado. Nunca anule o fio terra nem opere o equipamento sem um aterramento adequadamente instalado. Em caso de dúvida com relação ao sistema de aterramento disponível, entre em contato com os serviços locais de inspeção elétrica ou um eletricista qualificado.
Este equipo debe estar conectado a tierra. No inhabilite el conductor de tierra ni haga funcionar el equipo si no hay un conductor de tierra instalado correctamente. Póngase en contacto con la autoridad correspondiente de inspección eléctrica o con un electricista si no está seguro de que haya una conexión a tierra adecuada.
Varning!
Denna utrustning måste jordas. Koppla aldrig från jordledningen och använd aldrig utrustningen utan en på lämpligt sätt installerad jordledning. Om det föreligger osäkerhet huruvida lämplig jordning finns skall elektrisk besiktningsauktoritet eller elektriker kontaktas.
OL-10260-02
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
45
Translated Safety Warnings
46
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
OL-10260-02
Statement 1030—Equipment Installation
Translated Safety Warnings
Warning
Waarschuwing
Varoitus
Attention
Warnung
Avvertenza
Advarsel
Aviso
Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Deze apparatuur mag alleen worden geïnstalleerd, vervangen of hersteld door bevoegd geschoold personeel.
Tämän laitteen saa asentaa, vaihtaa tai huoltaa ainoastaan koulutettu ja laitteen tunteva henkilökunta.
Il est vivement recommandé de confier l'installation, le remplacement et la maintenance de ces équipements à des personnels qualifiés et expérimentés.
Das Installieren, Ersetzen oder Bedienen dieser Ausrüstung sollte nur geschultem, qualifiziertem Personal gestattet werden.
Questo apparato può essere installato, sostituito o mantenuto unicamente da un personale competente.
Bare opplært og kvalifisert personell skal foreta installasjoner, utskiftninger eller service på dette utstyret.
Apenas pessoal treinado e qualificado deve ser autorizado a instalar, substituir ou fazer a revisão deste equipamento.
¡Advertencia!
Varning!
Aviso
Solamente el personal calificado debe instalar, reemplazar o utilizar este equipo.
Endast utbildad och kvalificerad personal bör få tillåtelse att installera, byta ut eller reparera denna utrustning.
Somente uma equipe treinada e qualificada tem permissão para instalar, substituir ou dar manutenção a este equipamento.
OL-10260-02
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
47
Translated Safety Warnings
Advarsel
Kun uddannede personer må installere, udskifte komponenter i eller servicere dette udstyr.
Statement 1035—Proximity to Water
Warning
Waarschuwing
Varoitus
Attention
Warnung
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
48
Do not use this product near water; for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool.
Gebruik dit product niet in de buurt van water, zoals b.v. bij een badkuip, wasbak, keukenaanrecht of waskuip, in een vochtige kelder of in de buurt van een zwembad.
Älä käytä tätä tuotetta veden läheisyydessä, esimerkiksi lähellä kylpyammetta, käsienpesuallasta, keittiön pesuallasta tai pyykinpesuallasta, kosteassa kellarissa tai lähellä uima-allasta.
Ne jamais utiliser ce produit près d'un point d'eau (baignoire, évier, machine à laver,piscine) ou dans une pièce humide.
Dieses Gerät darf nicht in einer feuchten Umgebung, z.B. in der Nähe von Wasser, einer Badewanne, Waschschüssel, Küchenspüle, Swimming Pool, etc. eingesetzt werden.
Statement 1035
OL-10260-02
Translated Safety Warnings
Avvertenza
Advarsel
Aviso
¡Advertencia!
Varning!
Non utilizzate questo prodotto nella vicinanza di acqua, ad esempio vicino a una vasca da bagno, lavandino, locali d'acqua, cantine umide o piscine.
Produktet skal ikke brukes i nærheten av vann, f. eks. nær badekar, vaskeservant, oppvaskkum eller vaskebalje, i fuktig kjeller eller i nærheten av svømmebasseng.
Não utilizar este produto perto de água; por exemplo, perto de uma banheira, de um lavatório, de um lava-loiças ou de um tanque de lavagem de roupa, em cave húmida ou perto de uma piscina.
No utilice este producto cerca del agua; por ejemplo, cerca del baño, , del fregadero de la cocina, del lavadero, en un sótano mojado, o cerca de una piscina.
Produkten får ej nyttjas i våtutrymme, t.ex. i närheten av badkar, tvättfat, diskho eller tvättbalja, i fuktig källare eller i närheten av badbassäng.
Statement 1036—Telephone Jacks in Wet Locations
Warning
Waarschuwing
Varoitus
Attention
Warnung
OL-10260-02
Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.
Installeer telefoonaansluitingen nooit op vochtige locaties tenzij de aansluiting speciaal bestemd is voor vochtige locaties.
Älä asenna puhelimen pistokkeita kosteisiin tiloihin, ellei pistokkeita ole nimenomaisesti suunniteltu tällaisiin tiloihin.
Ne jamais installer de prises téléphoniques dans un local humide, sauf si celles-ci sont spécifiquement conçues pour cet usage.
Telefonanschlüsse niemals in feuchten Umgebungen installieren, es sei denn der Anschluß ist speziell für Feuchtumgebungen entwickelt!
Statement 1036
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
49
Translated Safety Warnings
Avvertenza
Advarsel
Aviso
¡Advertencia!
Varning!
Mai installare un jack telefonico in una zona bagnata almeno che il jack sia appositamente per zone bagnate.
Telefonkontakter skal aldri monteres i fuktige omgivelser, med mindre kontakten er spesielt laget for våtrom.
Nunca instalar tomadas telefónicas em locais húmidos, a menos que a tomada tenha sido especialmente concebida para esse efeito.
Nunca instale las rosetas del teléfono en zonas mojadas a menos que la roseta se diseñe específicamente para estas.
Endast specialkonstruerat telefonjack får installeras i våtutrymme.
Statement 1037—Uninsulated Wires or Terminals
Warning
Waarschuwing
Varoitus
Attention
Warnung
Avvertenza
Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.
Raak ongeïsoleerde telefoondraden of contacten nooit aan tenzij de telefoonlijn van de netwerkinterface werd ontkoppeld.
Älä kosketa eristämättömiä puhelinjohtoja tai liittimiä, ellei puhelinta ole irrotettu verkkoliittymästä.
Ne jamais toucher un câble téléphonique non isolé lorsque celui-ci est connecté au port réseau.
Niemals nicht-isolierte Telefonkabel berühren, außer wenn die Telefonleitung an der Netzwerkschnittstelle abgetrennt wurde!
Mai toccare cavi telefonici o terminali non isolati almeno che le linee telefoniche non siano state disconnesse dall'interfaccia rete.
Statement 1037
50
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
OL-10260-02
Translated Safety Warnings
Advarsel
Aviso
¡Advertencia!
Varning!
Telefonledninger eller -uttak som ikke er isolert, må aldri berøres, med mindre telefonlinjen er frakoplet telenettet.
Nunca tocar em fios ou terminais telefónicos não isolados, a menos que a linha telefónica tenha sido desligada ao nível da interface da rede.
Nunca toque los alambres o los terminales del teléfono a menos que la línea telefónica se haya desconectado en el interfaz de la red.
Telefonlinjer måste frånkopplas vid nätverksgränssnittet innan oisolerad telefonledning eller -uttag vidrörs.
Statement 1038—Telephone Use During an Electrical Storm
Warning
Waarschuwing
Varoitus
Attention
Warnung
Avvertenza
Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning.
Gebruik nooit een telefoon (tenzij het een draadloze telefoon is) tijdens onweer. Er bestaat een kleine kans op een elektrische schok door bliksem.
Vältä puhelimen (muun kuin langattoman puhelimen) käyttöä ukkosmyrskyn aikana. Salamoinnista voi aiheutua sähköiskuvaara.
Pour éviter tout risque de choc électrique lors d'un orage, il est recommandé de ne pas utiliser un téléphone autre qu'un appareil sans fil.
Vermeiden Sie die Benutzung eines Telefons während eines Gewitters (außer eines schnurlosen Geräts). Es besteht ein geringes Risiko eines elektrischem Schlags durch Blitze.
Non utilizzate il telefono (almeno che sia cellulare) durante un temporale elettrico. Ci sono rischi, anche se poco probabili, di scariche elettriche dovute a fulmini.
Statement 1038
OL-10260-02
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
51
Translated Safety Warnings
Advarsel
Aviso
¡Advertencia!
Varning!
Unngå å bruke telefonen (med mindre den er trådløs) i tordenvær. Det eksisterer en minimal risiko for elektrisk støt grunnet lynnedslag.
Evitar a utilização do telefone (que não seja do tipo sem fios) durante uma tempestade eléctrica. Pode haver o risco remoto de choque eléctrico provocado pelo relâmpago.
Evite usar el teléfono (a excepción de un teléfono inalámbrico) durante una tormenta. Puede correr peligro por la descarga eléctrica que emite el relámpago.
Undvik att telefonera (gäller ej trådlös telefon) under åskväder. Viss risk finns för elstöt vid blixtnedslag.
Statement 1040—Product Disposal
Warning
Waarschuwing
Varoitus
Attention
Warnung
Avvertenza
Ultimate disposal of this product should be handled according to all national laws and regulations.
Het uiteindelijke wegruimen van dit product dient te geschieden in overeenstemming met alle nationale wetten en reglementen.
Tämä tuote on hävitettävä kansallisten lakien ja määräysten mukaisesti.
La mise au rebut ou le recyclage de ce produit sont généralement soumis à des lois et/ou directives de respect de l'environnement. Renseignez-vous auprès de l'organisme compétent.
Die Entsorgung dieses Produkts sollte gemäß allen Bestimmungen und Gesetzen des Landes erfolgen.
Lo smaltimento di questo prodotto deve essere eseguito secondo le leggi e regolazioni locali.
52
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
OL-10260-02
Translated Safety Warnings
Advarsel
Aviso
¡Advertencia!
Varning!
Aviso
Endelig kassering av dette produktet skal være i henhold til alle relevante nasjonale lover og bestemmelser.
Deitar fora este produto em conformidade com todas as leis e regulamentos nacionais.
Al deshacerse por completo de este producto debe seguir todas las leyes y reglamentos nacionales.
Vid deponering hanteras produkten enligt gällande lagar och bestämmelser.
O descarte definitivo deste produto deve estar de acordo com todas as leis e regulamentações nacionais.
Advarsel
Endelig bortskaffelse af dette produkt skal ske i henhold til gældende love og regler.
OL-10260-02
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
53
Translated Safety Warnings
Statement 1042—Ring Signal Generator
This warning does not apply to Cisco 850 series and Cisco 870 series routers.
Warning
Waarschuwing
Varoitus
Attention
Warnung
This equipment contains a ring signal generator (ringer), which is a source of hazardous voltage. Do not touch the RJ-11 (phone) port wires (conductors), the conductors of a cable connected to the RJ-11 port, or the associated circuit-board when the ringer is active. The ringer is activated by an incoming call.
Deze apparatuur brengt een belsignaal voort wat op spanningsgevaar duidt. Wanneer de bel rinkelt, mogen de RJ-11-draden (telefoon), d.w.z. de geleiders van een aan de RJ-11-poort verbonden kabel, en de bijbehorende circuitplaat, niet aangeraakt worden. De bel wordt geactiveerd door een binnenkomend analoog gesprek.
Tämä laite on varustettu soittovirran generaattorilla (puhelinkello), jossa on vaarallinen jännite. Älä koske RJ-11 (puhelimen liittymän) liitäntäjohtoihin (johtimet), RJ-11-liittymään yhdistetyn kaapelin johtimiin tai piirilevyyn puhelinkellon ollessa päälle kytkettynä. Saapuva analogisoitto aktivoi puhelinkellon.
Cet appareil contient un générateur de sonneries, source de tensions dangereuses. Lorsque la sonnerie est active, ne touchez en aucun cas les fils de port (conducteurs) du connecteur RJ11 (téléphone), les âmes du câble connecté au port RJ11 ou les cartes imprimées correspondantes. La sonnerie est activée par un appel entrant.
Dieses Gerät enthält einen Rufsignalgeber (Rufumsetzer), der unter gefährlicher Spannung steht. Die RJ-11 (Telefon-) Anschlußdrähte (Leiter), die Leiter eines im RJ-11-Anschluß eingesteckten Kabels bzw. die dazugehörige Leiterplatte auf keinen Fall berühren, wenn der Rufumsetzer aktiviert ist. Der Rufumsetzer wird aktiviert, wenn ein Analoganruf eingeht.
54
Avvertenza
Advarsel
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
Questa apparecchiatura contiene un generatore di segnali di chiamata (suoneria) che origina un voltaggio pericoloso. Quando la suoneria è attivata, non toccare l’RJ-11 (telefono), i fili della porta (conduttori), i conduttori di un cavo collegato alla porta RJ-11 o l’associata scheda a circuiti stampati. La suoneria è attivata da un segnale di chiamata analogica in arrivo.
Dette utstyret inneholder en ringesignalgenerator (ringeklokke) med farlig spenning. Berør ikke RJ-11-utgangens (telefonutgangens) ledninger (lederne), lederne til den kabelen som er koplet til RJ-11-utgangen, eller tilhørende kretskort når ringeklokken er aktivert. Ringeklokken aktiveres av innkommende analoge anrop.
OL-10260-02
Translated Safety Warnings
Aviso
¡Advertencia!
Varning!
Este equipamento contém um gerador de sinal de campainha que constitui uma fonte de tensão perigosa. Não toque nos fios de porta (condutores) RJ-11 (telefone), nos condutores do cabo conectado à porta RJ-11 ou na placa de circuito associada quando a campainha estiver activa. A campainha é activada pela entrada de uma chamada analógica.
Este equipo contiene un generador de señal de llamada (timbre), el cual es una fuente de tensión peligrosa. No toque los alambres de la puerta (conductores) RJ-11 (teléfono), ni los conductores de un cable conectado a la puerta RJ-11, ni la placa del circuito relacionado cuando el timbre está activo. El timbre es activado por medio de una llamada de entrada analógica.
Denna utrustning innehåller en tongenerator (ringklocka) med farlig spänning. Vidrör inte RJ-11-portens (telefonportens) ledningar (ledarna), ledarna hos kabel som är ansluten till porten RJ-11 eller tillhörande kretskort när ringklockan är aktiverad. Ringklockan aktiveras av inkommande analoga anrop.
Statement 1073—No User-Serviceable Parts
This warning applies only to Cisco 850 series and Cisco 870 series routers.
Warning
Waarschuwing
Varoitus
Attention
OL-10260-02
No user-serviceable parts inside. Do not open.
Er zijn geen door de gebruiker te vervangen onderdelen. Niet openen.
Ei sisällä käyttäjän huollettavissa olevia osia. Älä avaa.
Aucune pièce se trouvant à l'intérieur ne peut être réparée ou remplacée par l'utilisateur. Ne pas ouvrir.
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
55
Translated Safety Warnings
Warnung
Avvertenza
Advarsel
Aviso
¡Advertencia!
Varning!
Enthält keine Teile, die vom Benutzer gewartet werden müssen. Bitte nicht öffnen.
Non contiene parti riparabili dall'utente. Non aprire.
Inneholder ingen deler som kan repareres av brukeren. Må ikke åpnes.
Sem peças sujeitas a manutenção pelo utilizador. Não abrir.
No contiene partes que puedan ser arregladas por el usuario. No abrir.
Det finns inga delar som användare kan utföra service på. Öppna inte.
Aviso
Advarsel
Manutenção somente por técnico especializado. Não abra.
Ingen dele indeni som brugere kan reparere. Åbn ej.
56
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
OL-10260-02
Translated Safety Warnings
Statement 1074—Comply with Local and National Electrical Codes
Warning
Waarschuwing
Varoitus
Attention
Warnung
Avvertenza
Advarsel
Aviso
¡Advertencia!
Varning!
Installation of the equipment must comply with local and national electrical codes.
Bij installatie van de apparatuur moet worden voldaan aan de lokale en nationale elektriciteitsvoorschriften.
Laitteisto tulee asentaa paikallisten ja kansallisten sähkömääräysten mukaisesti.
L'équipement doit être installé conformément aux normes électriques nationales et locales.
Die Installation der Geräte muss den Sicherheitsstandards entsprechen.
L'installazione dell'impianto deve essere conforme ai codici elettrici locali e nazionali.
Installasjon av utstyret må samsvare med lokale og nasjonale elektrisitetsforskrifter.
A instalação do equipamento tem de estar em conformidade com os códigos eléctricos locais e nacionais.
La instalación del equipo debe cumplir con las normativas de electricidad locales y nacionales.
Installation av utrustningen måste ske i enlighet med gällande elinstallationsföreskrifter.
OL-10260-02
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
57

Obtaining Documentation and Submitting a Service Request

Obtaining Documentation and Submitting a Service Request
For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What’s New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at:
http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html
Subscribe to the What’s New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS version 2.0.
This document is to be used in conjunction with the hardware installation guide and the cabling and setup quick start guide for your router.
CCVP, the Cisco logo, and Welcome to the Human Network are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn is a service mark of Cisco Systems, Inc.; and Access Registrar, Aironet, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, Enterprise/Solver, EtherChannel, EtherFast, EtherSwitch, Fast Step, Follow Me Browsing, FormShare, GigaDrive, HomeLink, Internet Quotient, IOS, iPhone, IP/TV, iQ Expertise, the iQ logo, iQ Net Readiness Scorecard, iQuick Study, LightStream, Linksys, MeetingPlace, MGX, Networkers, Networking Academy, Network Registrar, PIX, ProConnect, ScriptShare, SMARTnet, StackWise, The Fastest Way to Increase Your Internet Quotient, and TransPath are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries.
All other trademarks mentioned in this document or Website are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0711R)
Copyright © 2008 Cisco Systems, Inc. All rights reserved.
58
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
OL-10260-02
Loading...