Cisco NTP-E157, ONS 15600 Change Card Settings

Change Card Settings

This chapter explains how to change transmission settings on cards in a Cisco ONS 15600.

Before You Begin

As necessary, complete the “NTP-E57 Document Existing Provisioning” procedure on page 7-2.

Before performing the following procedures, investigate all alarms and clear any trouble conditions.
Refer to the Cisco ONS 15600 Troubleshooting Guide as necessary.

This section lists the chapter procedures (NTPs). Turn to a procedure for applicable tasks (DLPs).

1. NTP-E157 Provision a Multirate PPM, page 11-2—Complete this procedure to provision a multirate

pluggable port module (PPM), for the ASAP card. If a multirate PPM was preprovisioned, this
procedure is unnecessary.

2. NTP-E151 Provision an Optical Line Rate, page 11-3—Complete this procedure to provision the

optical line rate on a multirate PPM for the ASAP card. Single-rate PPMs do not need to be
provisioned.

CHA PTER

11

February 2008

3. NTP-E150 Change the Optical Line Rate, page 11-4—As needed, complete this procedure to edit

optical line rates for multirate PPMs on the ASAP card.

4. NTP-E149 Delete Pluggable Port Modules, page 11-5—As needed, complete this procedure to

delete PPMs for the ASAP card.

5. NTP-E66 Modify Line and Status Thresholds for Optical Ports, page 11-6—As needed, complete

this procedure to change line (drop) and threshold settings for all OC-N cards.

6. NTP-E105 Change an Optical Port to SDH, page 11-12—As needed, complete this procedure to

change an optical port from SONET to SDH.

7. NTP-E125 Change Card Service State, page 11-13—As needed, complete this procedure to change

card service state.

Cisco ONS 15600 Procedure Guide, R5.0

11-1

NTP-E157 Provision a Multirate PPM

NTP-E157 Provision a Multirate PPM

Purpose This procedure provisions a multirate pluggable port modules (PPMs) in

CTC.

Tools/Equipment None

Prerequisite Procedures NTP-E147 Install the ASAP Card, page 2-5

DLP-E211 Install the ASAP 4PIO Modules, page 18-12, as needed

DLP-E215 Install an SFP, page 18-14, as needed

Required/As Needed Required

Onsite/Remote Onsite or remote

Security Level Provisioning or higher

Step 1 Complete the “DLP-E26 Log into CTC” task on page 16-39 to log into an ONS 15600 on the network.

Step 2 Click the Alarms tab:

a. Verify that the alarm filter is not turned on. See the “DLP-E157 Disable Alarm Filtering” task on

page 17-50 as necessary.

b. Verify that no unexplained conditions appear on the network. If unexplained conditions appear,

resolve them before continuing. Refer to the Cisco ONS 15600 SONET Troubleshooting Guide.

c. Complete the “DLP-E76 Export CTC Data” task on page 16-98 to export alarm and condition

information.

Chapter 11 Change Card Settings

Step 3 In node view, double-click the ASAP card where you want to provision PPM settings.

Step 4 Click the Provisioning > Pluggable Port Modules tabs.

Step 5 In the Pluggable Port Modules pane, click Create. The Create PPM dialog box appears.

Step 6 In the Create PPM dialog box, complete the following:

• PPM—Click the slot number where the SFP is installed from the drop-down list.

• PPM Type—Click the number of ports supported by your SFP from the drop-down list. If only one

port is supported, PPM (1 port) is the only menu option.

Step 7 Click OK. The newly created port appears on the Pluggable Port Modules pane. The row on the

Pluggable Port Modules pane turns light blue and the Actual Equipment Type column lists the equipment
name.

Step 8 Verify that the PPM appears in the list on the Pluggable Port Modules pane. If it does not, repeat Steps

5 through 8.

Step 9 Repeat the task to provision a second PPM.

Step 10 Click OK.

Step 11 Continue with the “NTP-E151 Provision an Optical Line Rate” procedure on page 11-3 to provision the

line rate.

Stop. You have completed this procedure.

Cisco ONS 15600 Procedure Guide, R5.0

11-2

February 2008

Chapter 11 Change Card Settings

NTP-E151 Provision an Optical Line Rate

Purpose This procedure provisions the line rate on a multirate pluggable port

module (PPM). Single-rate small-form factor pluggables (SFPs) or 4-port
I/O modules (4PIOs) do not need line rate provisioning.

Tools/Equipment None

Prerequisite Procedures NTP-E148 Preprovision an SFP Slot, page 2-8 or

NTP-E157 Provision a Multirate PPM, page 11-2

Required/As Needed Required

Onsite/Remote Onsite or remote

Security Level Provisioning or higher

Step 1 Complete the “DLP-E26 Log into CTC” task on page 16-39 to log into an ONS 15600 on the network.

Step 2 Click the Alarms tab:

a. Verify that the alarm filter is not turned on. See the “DLP-E157 Disable Alarm Filtering” task on

page 17-50 as necessary.

NTP-E151 Provision an Optical Line Rate

b. Verify that no unexplained conditions appear on the network. If unexplained conditions appear,

resolve them before continuing. Refer to the Cisco ONS 15600 SONET Troubleshooting Guide.

c. Complete the “DLP-E76 Export CTC Data” task on page 16-98 to export alarm and condition

information.

Step 3 In node view, double-click the ASAP card where you want to provision the line rate.

Step 4 Click the Provisioning > Pluggable Port Modules tabs.

Step 5 In the Pluggable Ports pane, click Create. The Create Port dialog box appears.

Step 6 In the Create Port dialog box, complete the following:

• Port—Click the PPM number and port number from the drop-down list. The first number indicates

the PPM and the second number indicates the port number on the PPM. For example, the first PPM
with one port displays as 1-1 and the second PPM with one port displays as 2-1. When a 4PIO is
present on an ASAP card, the port is identified as 4PIO#-PPM#-Port# (for example 4-4-1). The 4PIO
number can be 1 to 4, the PPM number can be 1 to 4, but the port number is always 1.

• Port Type—Click the type of port from the drop-down list. The port type menu displays the

supported port rates on your PPM. See Table 11-1 for definitions of the supported rates on the ASAP
card.

Step 7 Click OK.

Step 8 Repeat Steps 5 through 7 to configure the port rates as needed.

Table 11-1 PPM Port Types

Card Port Type

ASAP

February 2008

• OC-3—155 Mbps

• OC-12—622 Mbps

• OC-48—2.48 Gbps

• ETHER—10 Gbps Ethernet

Cisco ONS 15600 Procedure Guide, R5.0

11-3

NTP-E150 Change the Optical Line Rate

Step 9 Click OK. The row on the Pluggable Ports pane turns light blue until the actual SFP is installed and then

the row turns white.

Stop. You have completed this procedure.

NTP-E150 Change the Optical Line Rate

Purpose This procedure changes PPM port rates for the ASAP card. Perform this

procedure if you want to change the port rate on a multi-rate SFP that is
already provisioned.

Tools/Equipment None

Prerequisite Procedures NTP-E157 Provision a Multirate PPM, page 11-2

Required/As Needed As needed

Onsite/Remote Onsite or remote

Security Level Provisioning or higher

Chapter 11 Change Card Settings

Step 1 Complete the “DLP-E26 Log into CTC” task on page 16-39 to log into an ONS 15600 on the network.

Step 2 Click the Alarms tab:

a. Verify that the alarm filter is not turned on. See the “DLP-E157 Disable Alarm Filtering” task on

page 17-50 as necessary.

b. Verify that no unexplained conditions appear on the network. If unexplained conditions appear,

resolve them before continuing. Refer to the Cisco ONS 15600 SONET Troubleshooting Guide.

c. Complete the “DLP-E76 Export CTC Data” task on page 16-98 to export alarm and condition

information.

Step 3 In node view, double-click the ASAP card where you want to edit the PPM port rate.

Step 4 Click the Provisioning > Pluggable Port Modules tabs.

Step 5 Click the port with the port rate you want to change in the Pluggable Ports pane. The highlight changes

to dark blue.

Step 6 Click Edit. The Edit Port Rate dialog box appears.

Step 7 In the Change To field, use the drop-down menu to select the new port rate and click OK.

Step 8 Click Yes on the Confirm Port Rate Change dialog box.

Stop. You have completed this procedure.

Cisco ONS 15600 Procedure Guide, R5.0

11-4

February 2008

Chapter 11 Change Card Settings

NTP-E149 Delete Pluggable Port Modules

Purpose This procedure deletes PPM provisioning for SFPs on the ASAP card.

Tools/Equipment None

Prerequisite Procedures NTP-E157 Provision a Multirate PPM, page 11-2

Required/As Needed As needed

Onsite/Remote Onsite or remote

Security Level Provisioning or higher

Step 1 Complete the “DLP-E26 Log into CTC” task on page 16-39 to log into an ONS 15600 on the network.

Step 2 Click the Alarms tab:

a. Verify that the alarm filter is not turned on. See the “DLP-E157 Disable Alarm Filtering” task on

page 17-50 as necessary.

b. Verify that no unexplained conditions appear on the network. If unexplained conditions appear,

resolve them before continuing. Refer to the Cisco ONS 15600 SONET Troubleshooting Guide.

NTP-E149 Delete Pluggable Port Modules

c. Complete the “DLP-E76 Export CTC Data” task on page 16-98 to export alarm and condition

information.

Step 3 You cannot delete a port on a PPM: if it is in service, part of a protection group, has a communications

channel termination in use, is used as a timing source, has circuits, or has overhead circuits. As needed,
complete the following procedures and task:

• NTP-E61 Modify or Delete Optical 1+1 Port Protection Settings, page 10-4

• NTP-E62 Change Node Timing, page 10-4

• NTP-E128 Modify or Delete Communications Channel Terminations and Provisionable Patchcords,

page 10-7

• NTP-E52 Modify and Delete Circuits, page 9-2

• NTP-E134 Modify and Delete Overhead Circuits, page 9-3

• DLP-E115 Change the Service State for a Port, page 17-14

Step 4 In node view, double-click the ASAP card where you want to delete PPM settings.

Step 5 Click the Provisioning > Pluggable Port Modules tabs.

Step 6 To delete a PPM and the associated ports:

a. Click the PPM line that appears in the Pluggable Port Modules pane. The highlight changes to dark

blue.

b. Click Delete. The Delete PPM dialog box appears.

c. Click Ye s. The PPM provisioning is removed from the Pluggable Port Modules pane and the

Pluggable Ports pane.

Step 7 Verify that the PPM provisioning is deleted:

• If the PPM was pre-provisioned, CTC shows an empty slot in CTC after it is deleted.

• If the SFP or 4PIO is physically present when you delete the PPM provisioning, CTC transitions to

the deleted state, the ports (if any) are deleted, and the PPM is represented as a gray graphic in CTC.
The SFP or 4PIO can be provisioned again in CTC, or the equipment can be removed, in which case
the removal causes the graphic to disappear.

February 2008

Cisco ONS 15600 Procedure Guide, R5.0

11-5

Chapter 11 Change Card Settings

NTP-E66 Modify Line and Status Thresholds for Optical Ports

Note If you need to remove the SFP, see the “DLP-E216 Remove an SFP” procedure on page 18-15.

If you need to remove the 4PIO, see the “DLP-E217 Remove a 4PIO Module” procedure on

page 18-16.”

Stop. You have completed this procedure.

NTP-E66 Modify Line and Status Thresholds for Optical Ports

Purpose This procedure changes line settings (line type, coding, and length), line

status (in service or out of service), and performance monitoring thresholds
for OC-48, OC-192 cards, and OC-N ports on ASAP cards.

Tools/Equipment None

Prerequisite Procedures NTP-E157 Provision a Multirate PPM, page 11-2

Required/As Needed As needed

Onsite/Remote Onsite or remote

Security Provisioning or higher

Step 1 Complete the “DLP-E26 Log into CTC” task on page 16-39 at the node where you want to change the

settings. If you are already logged in, continue with Step 2.

Step 2 Complete the “NTP-E69 Back Up the Database” procedure on page 14-4.

Step 3 On the shelf graphic, double-click the OC-N card that you want to provision. The card view appears.

Step 4 Click the Provisioning > Line tabs. (Click Provisioning > Optical > Line tabs for the ASAP card).

Step 5 As needed, provision the options in Table 11-2 for each OC-N port.

Table 11-2 OC-N Card Line Settings

Heading Description Options

Port # Identifies the port number

• For an OC-48 card: 1 – 16

• For an OC-192 card: 1 – 4

• For an ASAP card: up to 16 ports,

denoted by 4PIO module followed by
port number. (Example: 1-3-1
denotes the third port on 4PIO
Module 1.)

Port Name Provides the ability to assign the

specified port a name

User-defined; name can be up to 32
alphanumeric/special characters (blank
by default)

SF BER Sets the signal fail bit error rate

• 1E-3

Cisco ONS 15600 Procedure Guide, R5.0

11-6

• 1E-4 (default)

• 1E-5

February 2008

Chapter 11 Change Card Settings

Table 11-2 OC-N Card Line Settings (continued)

Heading Description Options

SD BER Sets the signal degrade bit error rate • 1E-5

Provides Sync Indicates that the port has been

Send Do Not
Use

BLSR Ext.
Byte

NTP-E66 Modify Line and Status Thresholds for Optical Ports

provisioned as a network element timing
reference on another node (ONS 15600,
ONS 15454, or ONS 15327)

When checked, sends a DUS (do not use)
message on the S1 byte

Chosen extended byte carries information
that governs BLSR protection switches.

• 1E-6

• 1E-7 (default)

• 1E-8

• 1E-9

Read-only

• Yes (checked)

• No (unchecked)

• Yes (checked)

• No (unchecked; default)

• K3

• Z2

• E2

• F1

Admin State Sets the port service state unless network

conditions prevent the change.

• IS—Puts the port in-service. The

port service state changes to IS-NR.

• IS,AINS (default)—Puts the port in

automatic in-service. The port
service state changes to
OOS-AU,AINS.

• OOS,DSBLD—Removes the port

from service and disables it. The port
service state changes to
OOS-MA,DSBLD.

• OOS,MT—Removes the port from

service for maintenance. The port
service state changes to
OOS-MA,MT.

AINS Soak Sets the automatic in-service soak period. Duration of valid input signal, in hh.mm

format, after which the card becomes in
service (IS) automatically (0 to 48 hours,
in 15-minute increments).

Type Defines the port as SONET or SDH.

Enable Sync Msg and Send Do Not Use
must be disabled before the port can be

• SONET (default)

• SDH

set to SDH.

February 2008

Cisco ONS 15600 Procedure Guide, R5.0

11-7

NTP-E66 Modify Line and Status Thresholds for Optical Ports

Table 11-2 OC-N Card Line Settings (continued)

Heading Description Options

Service State Identifies the autonomously generated

state that gives the overall condition of
the port. Service states appear in the
format: Primary State-Primary State
Qualifier, Secondary State.

SyncStatusMsg Allows you to view the incoming

synchronization status message by
clicking Show.

Chapter 11 Change Card Settings

• IS-NR—(In-Service and Normal)

The port is fully operational and
performing as provisioned.

• OOS-AU,AINS—(Out-Of-Service

and Autonomous, Automatic
In-Service) The port is
out-of-service, but traffic is carried.
Alarm reporting is suppressed. The
ONS node monitors the ports for an
error-free signal. After an error-free
signal is detected, the port stays in
OOS-AU,AINS state for the duration
of the soak period. After the soak
period ends, the port service state
changes to IS-NR.

• OOS-MA,DSBLD—(Out-of-Service

and Management, Disabled) The port
is out-of-service and unable to carry
traffic.

• OOS-MA,MT—(Out-of-Service and

Management, Maintenance) The port
is out-of-service for maintenance.
Alarm reporting is suppressed, but
traffic is carried and loopbacks are
allowed.

• PRS (Primary reference source –

Stratum 1)

• STU (Sync traceability unknown)

• ST2 (Stratum 2)

Enable Sync
Messages

Enables synchronization status messages
(S1 byte), which allow the node to choose
the best timing source

Step 6 Click Apply.

Cisco ONS 15600 Procedure Guide, R5.0

11-8

• ST3 (Stratum 3)

• ST3E (Stratum 3E)

• SMC (SONET minimum clock)

• ST4 (Stratum 4)

• TNC (Transit node clock)

• DUS (Do not use for timing

synchronization)

• RES (Reserved; quality level set by

user)

• Yes (checked, default)

• No (unchecked)

February 2008

Chapter 11 Change Card Settings

Step 7 Click the Thresholds subtab. The default selection is Near End, 15 Min, and Line (Figure 11-1).

Figure 11-1 Provisioning Thresholds for the OC-48 Card

NTP-E66 Modify Line and Status Thresholds for Optical Ports

Step 8

As needed, complete the following:

a. Click Line, Section, Path, or Physical to provision the line, section, path, and physical options in

Table 11-3 for each OC-N port.

b. Change the selection to Near End/Far End, 15 Min/1Day as necessary.

c. Click Refresh to view or modify the thresholds for each selection.

February 2008

Cisco ONS 15600 Procedure Guide, R5.0

11-9

NTP-E66 Modify Line and Status Thresholds for Optical Ports

Table 11-3 OC-N Threshold Options (Line, Section, and Path)

Heading Description Options

Port

CV

Port number 1 – 16 for an OC-48 card, 1 – 4 for an

Coding violations Numeric. Defaults (15 min/1 day):

Chapter 11 Change Card Settings

OC-192 card

Line

• 21260/212600 (OC-48 Near and Far

End)

• 85040/850400 (OC-192 Near and Far

End)

Section

• 10000/100000 (Near End); 0/0 (Far

End)

• 10000/500 (OC-192 Near and Far

End)

Path

ES

SES

SEFS

• 15/125 (OC-48/OC-192 Near and Far

End)

Errored seconds Numeric. Default (15 min/1 day):

Line

• 87/864 (Near and Far End)

Section

• 500/5000 (Near End); 0/0 (Far End)

Path

• 12/100 (OC-48/OC-192 Near and Far

End)

Severely errored seconds Numeric. Defaults (15 min/1 day):

Line

• 1/4 (Near and Far End)

Section

• 500/5000 (Near End); 0/0 (Far End)

Path

• 3/7 (OC-48/OC-192 Near and Far

End)

Severely errored framing seconds Numeric. Defaults (15 min/1 day):

Section

Cisco ONS 15600 Procedure Guide, R5.0

11-10

• 500/5000 (Near End); 0/0 (Far End)

February 2008

Chapter 11 Change Card Settings

Table 11-3 OC-N Threshold Options (Line, Section, and Path) (continued)

Heading Description Options

FC

UAS

PSC

NTP-E66 Modify Line and Status Thresholds for Optical Ports

Failure count Numeric. Defaults (15 min/1 day):

Line

• 10/40 (OC-48/OC-192 Near and Far

End)

Path

• 10/10 (OC-48/OC-192 Near and Far

End)

Unavailable seconds Numeric. Defaults (15 min/1 day):

Line

• 3/10 (OC-48/OC-192 Near and Far

End)

Path

• 10/10 (Near and Far End)

Protection Switching Count (Line) Numeric. Defaults (15 min/1 day):

Line

PSD

PSC-W

Protection Switch Duration (Line) Numeric. Defaults (15 min/1 day):

Protection Switching Count (Working
Line)

PSD-W

Protection Switch Duration (Working
Line)

Step 9 As needed, complete the following:

a. Click Physical to provision the physical options in Table 11-4 for each OC-N port.

b. Change the selection to 15 Min or 1 Day as necessary.

c. Click Refresh to view or modify the thresholds for each selection.

• 1/5 (Near End)

• 0/0 (Far End)

Line

• 300/600 (Near End)

• 0/0 (OC-48/OC-192 Far End)

Numeric. Defaults (15 min/1 day):

Line

• 1/5 (Near End)

Numeric. Defaults (15 min/1 day):

Line

• 300/600 (Near End)

February 2008

Cisco ONS 15600 Procedure Guide, R5.0

11-11

NTP-E105 Change an Optical Port to SDH

Table 11-4 OC-N Threshold Options (Physical)

Heading Description Options

Port

LBC-HIGH

LBC-LOW

OPT-HIGH

OPT-LOW

OPR-HIGH

OPR-LOW

Set OPR

Chapter 11 Change Card Settings

Port number 1 – 16 for an OC-48 card, 1 – 4 for an

OC-192 card

Laser bias current–maximum Default (15 min/1 day): 150 percent

Laser bias current–minimum Default (15 min/1 day): 50 percent

Optical power transmitted–maximum Default (15 min/1 day): 120 percent

Optical power transmitted–minimum Default (15 min/1 day): 80 percent

Optical power received–maximum Default (15 min/1 day): 200 percent

Optical power received–minimum Default (15 min/1 day): 50 percent

Setting the optical power received (OPR) establishes the received power level as 100%.
If the receiver power decreases, then the OPR percentage decreases to reflect the loss
in receiver power. For example, if the receiver power decreases 3 dBm, the OPR
decreases 50%.

Step 10 Click Apply.

Note See Chapter 7, “Manage Alarms,” for information about the Alarm Behavior tab, including

alarm profiles and alarm suppression.

Stop. You have completed this procedure.

NTP-E105 Change an Optical Port to SDH

Purpose This procedure provisions a port on an OC-N card for SDH.

Tools/Equipment None

Prerequisite Procedures None

Required/As Needed As needed

Onsite/Remote Onsite or remote

Security Level Provisioning or higher

Step 1 Complete the “DLP-E26 Log into CTC” task on page 16-39 at the node where you want to change the

settings. If you are already logged in, continue with Step 2.

Step 2 Double-click the OC-N card where you want to provision a port for SDH.

Step 3 Click the Provisioning > Line tabs.

Step 4 In the Type field, specify the port and choose SDH.

Step 5 Click Apply.

Cisco ONS 15600 Procedure Guide, R5.0

11-12

February 2008

Chapter 11 Change Card Settings

Step 6 You can repeat Steps 4 and 5 for any other ports on that card.

Stop. You have completed this procedure.

NTP-E125 Change Card Service State

Purpose This procedure changes card service state.

Tools/Equipment None

Prerequisite Procedures Chapter 2, “Install Cards and Fiber-Optic Cable”

Required/As Needed As needed

Onsite/Remote Onsite or remote

Security Level Provisioning or higher

Step 1 Complete the “DLP-E26 Log into CTC” task on page 16-39 at the node where you want to change the

card service state.

Step 2 Click the Inventory tab.

Step 3 Click Admin State for the card you want to change, and choose an Admin state from the drop-down list:

IS (In-Service) or OOS,MT (Out-of-Service,Maintenance).

NTP-E125 Change Card Service State

Step 4 Click Apply.

Step 5 If an error message opens indicating that the card state cannot be changed from its current state, click

OK.

Table 11-5 lists possible card service state transitions based on the Admin State chosen. For more

information about the enhanced state model and card state transitions, refer to the “Administrative and
Service States” appendix of the Cisco ONS 15600 Reference Manual.

Table 11-5 Cisco ONS 15600 Card State Transitions

Admin State Original Service State Next Service State

IS OOS-AUMA,MT & UEQ

(Out-of-Service and Autonomous
Management,Maintenance and

OOS-AU,UEQ
(Out-of-Service &
Autonomous,Unequipped)

Unequipped)

IS OOS-AUMA,MEA & MT

(Out-of-Service and Autonomous
Management,Mismatched Equipment and

OOS-AU,MEA
(Out-of-Service and
Autonomous,Mismatched Equipment)

Maintenance)

IS OOS-MA,MT

(Out-of-Service and

IS-NR
(In-Service and Normal)

Management,Maintenance)

OOS,MT OOS-AU,MEA

(Out-of-Service and
Autonomous,Mismatched Equipment)

OOS-AUMA,MT & UEQ
(Out-of-Service and Autonomous
Management,Maintenance and
Unequipped)

February 2008

Cisco ONS 15600 Procedure Guide, R5.0

11-13

NTP-E125 Change Card Service State

Table 11-5 Cisco ONS 15600 Card State Transitions (continued)

Admin State Original Service State Next Service State

OOS,MT OOS-AU,AINS & UEQ

OOS,MT OOS-AU,AINS & MEA

OOS,MT OOS-AU,UEQ

OOS,MT IS-NR

(Out-of-Service and Autonomous,Auto
In-Service and Unequipped)

(Out-of-Service and Autonomous,Auto
In-Service and Mismatched Equipment)

(Out-of-Service and
Autonomous,Unequipped)

(In-Service and Normal)

Chapter 11 Change Card Settings

OOS-AUMA,MT & UEQ
(Out-of-Service and Autonomous
Management,Maintenance and
Unequipped)

OOS-AUMA,MEA & MT
(Out-of-Service and Autonomous
Management,Mismatched Equipment
and Maintenance)

OOS-AUMA,MT & UEQ
(Out-of-Service and Autonomous
Management,Maintenance and
Unequipped)

OOS-MA,MT
(Out-of-Service and
Management,Maintenance)

Stop. You have completed this procedure.

Cisco ONS 15600 Procedure Guide, R5.0

11-14

February 2008