Cisco Nexus 9200 Service Manual

Cisco Nexus 92160YC-X NX-OS Mode Switch Hardware Installation Guide

First Published: 2016-02-08
Last Modified: 2018-06-29
Americas Headquarters
Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 527-0883
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.
The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to correct the interference at their own expense.
The following information is for FCC compliance of Class B devices: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If the equipment causes interference to radio or television reception, which can be determined by turning the equipment off and on, users are encouraged to try to correct the interference by using one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Modifications to this product not authorized by Cisco could void the FCC approval and negate your authority to operate the product
The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public domain version of the UNIX operating system. All rights reserved. Copyright©1981, Regents of the University of California.
NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED "AS IS" WITH ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.
IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com
go trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any
other company. (1721R)
©
2016–2017 Cisco Systems, Inc. All rights reserved.

CONTENTS

Trademarks ?
PREFACE
CHAPTER 1
CHAPTER 2
Preface vii
Audience vii
Documentation Conventions vii
Related Documentation for Cisco Nexus 9000 Series NX-OS Software viii
Documentation Feedback x
Obtaining Documentation and Submitting a Service Request x
Overview 1
Overview 1
Preparing the Site 5
Temperature Requirements 5
Humidity Requirements 5
Altitude Requirements 5
Dust and Particulate Requirements 6
Minimizing Electromagnetic and Radio Frequency Interference 6
CHAPTER 3
Shock and Vibration Requirements 7
Grounding Requirements 7
Planning for Power Requirements 7
Airflow Requirements 9
Rack and Cabinet Requirements 9
Clearance Requirements 10
Installing the Switch Chassis 13
Cisco Nexus 92160YC-X NX-OS Mode Switch Hardware Installation Guide
iii
Contents
Safety 13
Installation Options with Racks and Cabinets 14
Airflow Considerations 14
Installation Guidelines 14
Unpacking and Inspecting the Switch 15
Installing the Switch 16
Grounding the Chassis 21
Starting the Switch 22
CHAPTER 4
CHAPTER 5
Connecting the Switch to the Network 25
Setting Up the Management Interface 25
Uplink Connections 25
Downlink Connections 26
Guidelines for Connecting Ports 26
Maintaining Transceivers and Optical Cables 28
Replacing Modules 29
Replacing a Fan Module 29
Removing a Fan Module 29
Installing a Fan Module 30
Replacing a Power Supply Module 30
Removing an AC Power Supply 31
Removing an HVAC/HVDC Power Supply 31
Removing a DC Power Supply 32
Installing an AC Power Supply 32
APPENDIX A
iv
Installing an HVAC/HVDC Power Supply 34
Installing a DC Power Supply 35
Wiring a 48 V DC Electrical Connector Block 35
Rack Specifications 39
Overview of Racks 39
General Requirements for Cabinets and Racks 39
Requirements Specific to Standard Open Racks 40
Requirements Specific to Perforated Cabinets 40
Cisco Nexus 92160YC-X NX-OS Mode Switch Hardware Installation Guide
Cable Management Guidelines 40
Contents
APPENDIX B
System Specifications 41
Environmental Specifications 41
Switch Dimensions 41
Switch and Module Weights and Quantities 42
Transceiver and Cable Specifications 42
Switch Power Input Requirements 42
Power Specifications 43
650-W AC Power Supply Specifications 43
1200-W HVAC/HVDC Power Supply Specifications 43
930-W DC Power Supply (Port-Side Intake) Specifications 44
930-W DC Power Supply (Port-Side Exhaust) Specifications 45
Power Cable Specifications 45
AC Power Cables Supported by NX-OS Mode Switches 45
HVAC/HVDC Power Cables Supported by ACI-Mode and NX-OS Mode Switches 46
DC Power Cable Specifications 47
Regulatory Standards Compliance Specifications 47
APPENDIX C
APPENDIX D
APPENDIX E
LEDs 49
Switch Chassis LEDs 49
Fan Module LEDs 50
Power Supply LEDs 50
Additional Kits 51
Rack Mount Kit N3K-C3064-ACC-KIT 51
Site Preparation and Maintenance Records 53
Site Preparation Checklist 53
Contact and Site Information 54
Chassis and Module Information 55
Cisco Nexus 92160YC-X NX-OS Mode Switch Hardware Installation Guide
v
Contents
Cisco Nexus 92160YC-X NX-OS Mode Switch Hardware Installation Guide
vi

Preface

Audience, on page vii
Documentation Conventions, on page vii
Related Documentation for Cisco Nexus 9000 Series NX-OS Software, on page viii
Documentation Feedback, on page x
Obtaining Documentation and Submitting a Service Request, on page x

Audience

This publication is for hardware installers and network administrators who install, configure, and maintain Cisco Nexus switches.

Documentation Conventions

Command descriptions use the following conventions:
bold
DescriptionConvention
Bold text indicates the commands and keywords that you enter literally as shown.
Italic
[x | y]
{x | y}
[x {y | z}]
variable
Italic text indicates arguments for which the user supplies the values.
Square brackets enclose an optional element (keyword or argument).[x]
Square brackets enclosing keywords or arguments separated by a vertical bar indicate an optional choice.
Braces enclosing keywords or arguments separated by a vertical bar indicate a required choice.
Nested set of square brackets or braces indicate optional or required choices within optional or required elements. Braces and a vertical bar within square brackets indicate a required choice within an optional element.
Indicates a variable for which you supply values, in context where italics cannot be used.
Cisco Nexus 92160YC-X NX-OS Mode Switch Hardware Installation Guide
vii

Related Documentation for Cisco Nexus 9000 Series NX-OS Software

Preface
DescriptionConvention
string
Examples use the following conventions:
italic screen font
!, #
A nonquoted set of characters. Do not use quotation marks around the string or the string will include the quotation marks.
DescriptionConvention
Terminal sessions and information the switch displays are in screen font.screen font
Information you must enter is in boldface screen font.boldface screen font
Arguments for which you supply values are in italic screen font.
Nonprinting characters, such as passwords, are in angle brackets.< >
Default responses to system prompts are in square brackets.[ ]
An exclamation point (!) or a pound sign (#) at the beginning of a line of code indicates a comment line.
Related Documentation for Cisco Nexus 9000 Series NX-OS Software
The entire Cisco NX-OS 9000 Series documentation set is available at the following URL:
https://www.cisco.com/en/US/products/ps13386/tsd_products_support_series_home.html
Release Notes
The release notes are available at the following URL:
https://www.cisco.com/en/US/products/ps13386/prod_release_notes_list.html
Configuration Guides
These guides are available at the following URL:
https://www.cisco.com/en/US/products/ps13386/products_installation_and_configuration_guides_list.html
The documents in this category include:
Cisco Nexus 2000 Series NX-OS Fabric Extender Software Configuration Guide for Cisco Nexus 9000
Series Switches
Cisco Nexus 9000 Series NX-OS Fundamentals Configuration Guide
Cisco Nexus 9000 Series NX-OS High Availability and Redundancy Guide
Cisco Nexus 9000 Series NX-OS Interfaces Configuration Guide
Cisco Nexus 9000 Series NX-OS Layer 2 Switching Configuration Guide
Cisco Nexus 9000 Series NX-OS Multicast Routing Configuration Guide
viii
Cisco Nexus 92160YC-X NX-OS Mode Switch Hardware Installation Guide
Preface
Preface
Cisco Nexus 9000 Series NX-OS Quality of Service Configuration Guide
Cisco Nexus 9000 Series NX-OS Security Configuration Guide
Cisco Nexus 9000 Series NX-OS System Management Configuration Guide
Cisco Nexus 9000 Series NX-OS Unicast Routing Configuration Guide
Cisco Nexus 9000 Series NX-OS Verified Scalability Guide
Cisco Nexus 9000 Series NX-OS VXLAN Configuration Guide
Other Software Documents
Cisco Nexus 7000 Series and 9000 Series NX-OS MIB Quick Reference
Cisco Nexus 9000 Series NX-OS Programmability Guide
Cisco Nexus 9000 Series NX-OS Software Upgrade and Downgrade Guide
Cisco Nexus 9000 Series NX-OS System Messages Reference
Cisco Nexus 9000 Series NX-OS Troubleshooting Guide
Cisco NX-OS Licensing Guide
Cisco NX-OS XML Interface User Guide
Hardware Documents
Cisco Nexus 3000 Series Hardware Installation Guide
Cisco Nexus 92160YC-X NX-OS Mode Switch Hardware Installation Guide
Cisco Nexus 92300YC NX-OS Mode Switch Hardware Installation Guide
Cisco Nexus 92304QC NX-OS Mode Switch Hardware Installation Guide
Cisco Nexus 9236C NX-OS Mode Switch Hardware Installation Guide
Cisco Nexus 9272Q NX-OS Mode Switch Hardware Installation Guide
Cisco Nexus 93108TC-EX NX-OS Mode Switch Hardware Installation Guide
Cisco Nexus 93120TX NX-OS Mode Switch Hardware Installation Guide
Cisco Nexus 93128TX NX-OS Mode Switch Hardware Installation Guide
Cisco Nexus 93180LC-EX NX-OS Mode Switch Hardware Installation Guide
Cisco Nexus 93180YC-EX NX-OS Mode Switch Hardware Installation Guide
Cisco Nexus 9332PQ NX-OS-Mode Switch Hardware Installation Guide
Cisco Nexus 9372PX and 9372PX-E NX-OS Mode Switches Hardware Installation Guide
Cisco Nexus 9372TX and 9372TX-E NX-OS Mode Switches Hardware Installation Guide
Cisco Nexus 9396PX NX-OS Mode Switch Hardware Installation Guide
Cisco Nexus 9396TX NX-OS Mode Switch Hardware Installation Guide
Cisco Nexus 92160YC-X NX-OS Mode Switch Hardware Installation Guide
ix
Preface

Documentation Feedback

Cisco Nexus 9504 NX-OS Mode Switch Hardware Installation Guide
Cisco Nexus 9508 NX-OS Mode Switch Hardware Installation Guide
Cisco Nexus 9516 NX-OS Mode Switch Hardware Installation Guide
Regulatory, Compliance, and Safety Information for the Cisco Nexus 3000 and 9000 Series
Documentation Feedback
To provide technical feedback on this document, or to report an error or omission, please send your comments to nexus9k-docfeedback@cisco.com. We appreciate your feedback.

Obtaining Documentation and Submitting a Service Request

For information on obtaining documentation, using the Cisco Bug Search Tool (BST), submitting a service request, and gathering additional information, see What's New in Cisco Product Documentation, at:
https://www.cisco.com/warp/public/687/Directory/DirTAC.shtml.
Subscribe to What's New in Cisco Product Documentation, which lists all new and revised Cisco technical documentation as an RSS feed and delivers content directly to your desktop using a reader application. The RSS feeds are a free service.
Cisco Nexus 92160YC-X NX-OS Mode Switch Hardware Installation Guide
x

Overview

CHAPTER 1

Overview

Overview, on page 1
The Cisco Nexus 92160YCX switch (N9K-C92160YC-X) is a 1 rack unit (RU) switch that has the following ports:
• 48 10/25-Gigabit SFP+ downlink ports supporting 1-, 10-, or 25-Gigabit speeds (you can set these speeds on a port-by-port basis)
• 6 100-Gigabit QSFP28 uplink ports supporting 40- or 100-Gigabit speeds as follows: (40-Gigabits for all six ports or up to 100-Gigabits for ports 49 to 52)
• 4 x 100 Gigabit Ethernet (ports 49 to 52)
Note
Ports 50 and 52 also provide 4x10- or 4x25-Gigabit Ethernet breakout support.
• 2 x 100 Gigabit Ethernet (ports 50 and 52) and 4 x 40 Gigabit Ethernet (ports 49, 51, 53, and 54)
• 6 x 40 Gigabit Ethernet (ports 49 to 54)
Note
Ports 50 and 52 also provide 4x10- or 4x25-Gigabit Ethernet breakout support.
• 2 network management ports (RJ-45 and SFP)
• 1 RS-232 console port for setting the initial switch configuration
• 1 USB port for saving or loading switch configurations
The chassis for this switch includes the following user-replaceable components:
• Fan modules (four) with the following airflow choices:
• Port-side intake fan module with burgundy coloring (NXA-FAN-30CFM-B)
• Port-side exhaust fan module with blue coloring (NXA-FAN-30CFM-F)
Cisco Nexus 92160YC-X NX-OS Mode Switch Hardware Installation Guide
1
Overview
Overview
• Power supply modules (two—one for operations and one for redundancy [1+1]) with the following choices:
• 650-W port-side intake AC power supply with burgundy coloring (NXA-PAC-650W-PI)
• 650-W port-side exhaust AC power supply with blue coloring (NXA-PAC-650W-PE)
• 1200-W HVAC/HVDC dual-direction airflow power supply with white coloring (N9K-PUV-1200W)
• 930-W port-side intake DC power supply with green coloring (UCSC-PSU-930WDC)
• 930-W port-side exhaust DC power supply with gray coloring (UCS-PSU-6332-DC)
Note
Both power supplies should be the same type. Do not mix AC, DC, or HVAC/HVDC power supplies.
Note
All fan modules and power supplies must use the same airflow direction during operations. If you are using the 1200-W HVAC/HVDC power supplies, those power supplies automatically use the same airflow direction as used by the other modules in the switch.
The following figure shows the switch features on the port side of the chassis.
1
4Beacon (BCN), Status (STS), and Environment (ENV) LEDs
2
downlink ports (48) supporting 1-, 10-, and 25-Gigabit Ethernet
Screw holes for mounting brackets
Grounding pad510-Gigabit SFP+
3
100-Gigabit QSFP28 uplink ports (6) supporting 40- and 100-Gigabit Ethernet
To determine which transceivers, adapters, and cables are supported by this switch, see the Cisco Transceiver
Modules Compatibility Information document.
Cisco Nexus 92160YC-X NX-OS Mode Switch Hardware Installation Guide
2
Overview
Overview
The following figure shows the switch features on the power supply side of the chassis.
1
Grounding pad5Power supply modules (1 or 2) (AC power supplies shown) with slots numbered 1 (left) and 2 (right)
2
Console port (1)6Fan modules (4) with slots numbered from 1 (left) to 4 (right)
3
7Beacon (BCN) and Status
(STS) LEDs
Management ports
(2—RJ-45 and SFP)
USB port (1)4
Depending on whether you plan to position the ports in a hot or cold aisle, you can order the fan and power supply modules with port-side intake or port-side exhaust airflow. For port-side intake airflow, the fan and AC power supply modules have burgundy coloring (DC power supply modules have green coloring). For port-side exhaust airflow, the fan and AC power supplies have blue coloring (DC power supply modules have gray coloring). You can also order the 1200-W HVAC/HVDC power supply which has dual-direction airflow with white coloring. Dual-direction airflow modules automatically use the airflow direction of the other modules installed in the switch.
The fan and power supply modules are field replaceable and you can replace one fan module or one power supply module during operations so long as the other modules are installed and operating. If you have only one power supply installed, you can install the replacement power supply in the open slot before removing the original power supply.
Note
Caution
All of the fan and power supply modules must have the same direction of airflow. Otherwise, the switch can overheat and shut down. If you are installing a dual-direction power supply, that module will automatically use the same airflow direction as the other modules in the switch.
If the switch has port-side intake airflow (burgundy coloring for fan modules), you must locate the ports in the cold aisle. If the switch has port-side exhaust airflow (blue coloring for fan modules), you must locate the ports in the hot aisle. If you locate the air intake in a hot aisle, the switch can overheat and shut down.
Cisco Nexus 92160YC-X NX-OS Mode Switch Hardware Installation Guide
3
Overview
Overview
Cisco Nexus 92160YC-X NX-OS Mode Switch Hardware Installation Guide
4

Preparing the Site

Temperature Requirements, on page 5
Humidity Requirements, on page 5
Altitude Requirements, on page 5
Dust and Particulate Requirements, on page 6
Minimizing Electromagnetic and Radio Frequency Interference, on page 6
Shock and Vibration Requirements, on page 7
Grounding Requirements, on page 7
Planning for Power Requirements, on page 7
Airflow Requirements, on page 9
Rack and Cabinet Requirements, on page 9
Clearance Requirements, on page 10

Temperature Requirements

The switch requires an operating temperature of 32 to 104 degrees Fahrenheit (0 to 40 degrees Celsius). If the switch is not operating, the temperature must be between –40 to 158 degrees Fahrenheit (–40 to 70 degrees Celsius).
CHAPTER 2

Humidity Requirements

High humidity can cause moisture to enter the switch. Moisture can cause corrosion of internal components and degradation of properties such as electrical resistance, thermal conductivity, physical strength, and size. The switch is rated to withstand from 5- to 95-percent (non-condensing) relative humidity.
Buildings in which the climate is controlled by air-conditioning in the warmer months and by heat during the colder months usually maintain an acceptable level of humidity for the switch equipment. However, if the switch is located in an unusually humid location, you should use a dehumidifier to maintain the humidity within an acceptable range.

Altitude Requirements

The following table lists the maximum altitude that this switch is tested to operate. This switch is rated to operate at altitudes from 0 to 13,123 feet (0 to 4,000 meters). If you operate this switch at a higher altitude
Cisco Nexus 92160YC-X NX-OS Mode Switch Hardware Installation Guide
5

Dust and Particulate Requirements

(low pressure), the efficiency of forced and convection cooling is reduced and can result in electrical problems that are related to arcing and corona effects. This condition can also cause sealed components with internal pressure, such as electrolytic capacitors, to fail or to perform at a reduced efficiency.
Dust and Particulate Requirements
Exhaust fans cool power supplies and system fans cool switches by drawing in air and exhausting air out through various openings in the chassis. However, fans also ingest dust and other particles, causing contaminant buildup in the switch and increased internal chassis temperature. A clean operating environment can greatly reduce the negative effects of dust and other particles, which act as insulators and interfere with the mechanical components in the switch.
In addition to regular cleaning, follow these precautions to avoid contamination of your switch:
• Do not permit smoking near the switch.
• Do not permit food or drink near the switch.
Preparing the Site

Minimizing Electromagnetic and Radio Frequency Interference

Electromagnetic interference (EMI) and radio frequency interference (RFI) from the switch can adversely affect other devices, such as radio and television (TV) receivers, operating near the switch. Radio frequencies that emanate from the switch can also interfere with cordless and low-power telephones. Conversely, RFI from high-power telephones can cause spurious characters to appear on the switch monitor.
RFI is defined as any EMI with a frequency above 10 kHz. This type of interference can travel from the switch to other devices through the power cable and power source or through the air as transmitted radio waves. The Federal Communications Commission (FCC) publishes specific regulations to limit the amount of EMI and RFI that can be emitted by computing equipment. Each switch meets these FCC regulations.
To reduce the possibility of EMI and RFI, follow these guidelines:
• Cover all open expansion slots with a blank filler plate.
• Always use shielded cables with metal connector shells for attaching peripherals to the switch.
When wires are run for any significant distance in an electromagnetic field, interference can occur between the field and the signals on the wires with the following implications:
• Bad wiring can result in radio interference emanating from the plant wiring.
• Strong EMI, especially when it is caused by lightning or radio transmitters, can destroy the signal drivers and receivers in the chassis and even create an electrical hazard by conducting power surges through lines into equipment.
Note
To predict and prevent strong EMI, you might need to consult experts in radio frequency interference (RFI).
The wiring is unlikely to emit radio interference if you use twisted-pair cable with a good distribution of grounding conductors. If you exceed the recommended distances, use a high-quality twisted-pair cable with one ground conductor for each data signal when applicable.
Cisco Nexus 92160YC-X NX-OS Mode Switch Hardware Installation Guide
6
Preparing the Site

Shock and Vibration Requirements

Caution
If the wires exceed the recommended distances, or if wires pass between buildings, give special consideration to the effect of a lightning strike in your vicinity. The electromagnetic pulse caused by lightning or other high-energy phenomena can easily couple enough energy into unshielded conductors to destroy electronic switches. You might want to consult experts in electrical surge suppression and shielding if you had similar problems in the past.
Shock and Vibration Requirements
The switch has been shock- and vibration-tested for operating ranges, handling, and earthquake standards.

Grounding Requirements

The switch is sensitive to variations in voltage supplied by the power sources. Overvoltage, undervoltage, and transients (or spikes) can erase data from memory or cause components to fail. To protect against these types of problems, ensure that there is an earth-ground connection for the switch. You can connect the grounding pad on the switch either directly to the earth-ground connection or to a fully bonded and grounded rack.
When you properly install the chassis in a grounded rack, the switch is grounded because it has a metal-to-metal connection to the rack. Alternatively, you can ground the chassis by using a customer-supplied grounding cable that meets your local and national installation requirements (we recommend 6-AWG wire for U.S. installations) connected to the chassis with a grounding lug (provided in the switch accessory kit) and to the facility ground.
Note
You automatically ground AC power supplies when you connect them to AC power sources. For DC power supplies, you must connect a grounding wire when wiring the power supply to the DC power source.

Planning for Power Requirements

The switch includes two power supplies (1-to-1 redundancy with current sharing) in one of the following combinations:
• Two 650-W AC power supplies (NEBS compliant)
• Two 1200-W HVAC/HVDC power supplies
• Two 930-W DC power supplies
Note
Both power supplies must be the same type. Do not mix AC, DC, and HVAC/HVDC power supplies in the same chassis.
Cisco Nexus 92160YC-X NX-OS Mode Switch Hardware Installation Guide
7
Planning for Power Requirements
Note
For n+1 redundancy, you can use one or two power sources for the two power supplies. For n+n redundancy, you must use two power sources and connect each power supply to a separate power source.
The power supplies are rated to output up to 650 W (AC power supplies), up to 1200 W (HVAC/HVDC power supplies), or up to 930 W (DC power supplies), but the switch requires less than those amounts of power from the power supply. To operate the switch you must provision enough power from the power source to cover the requirements of both the switch and a power supply. Typically, this switch and a power supply require either 150 W (for 10-Gigabit downlink interfaces) or 170 W (for 25-Gigabit downlink interfaces) of power input from the power source, but you must provision as much as 475 W of power input from the power source to cover peak demand.
Note
Some of the power supply modules have Underwriter Labs (UL) rating capabilities that exceed the switch requirements. When calculating power requirements, use the switch requirements to determine the amount of power required for the power supplies.
Preparing the Site
Note
Warning
Note
Warning
To minimize the possibility of circuit failure, make sure that each power-source circuit used by the switch is dedicated to the switch.
For AC input application, please refer to the statement below:
Statement 1005—Circuit Breaker
This product relies on the building's installation for short-circuit (overcurrent) protection. Ensure that the protective devices are rated not greater than 20A (North America), 16A (Europe), and 13A (UK).
For DC input application, please refer to the statement below:
Statement 1005—Circuit Breaker
This product relies on the building's installation for short-circuit (overcurrent) protection.
• Ensure that the protective devices are rated not greater than 40A when the switch is powered with regular DC power supplies (rated 48-60VDC).
• Ensure that the protective devices are rated not greater than 10A when the switch is powered with HVDC power supplies (rated 240-350VDC).
Cisco Nexus 92160YC-X NX-OS Mode Switch Hardware Installation Guide
8
Preparing the Site
Note
For the power cables to use with the power supplies, see Power Cable Specifications, on page 45.

Airflow Requirements

The switch is designed to be positioned with its ports in either the front or the rear of the rack depending on your cabling and maintenance requirements. Depending on which side of the switch faces the cold aisle, you must have fan and power supply modules that move the coolant air from the cold aisle to the hot aisle in one of the following ways:
• Port-side exhaust airflow—Coolant air enters the chassis through the fan and power supply modules in the cold aisle and exhausts through the port end of the chassis in the hot aisle.
• Port-side intake airflow—Coolant air enters the chassis through the port end in the cold aisle and exhausts through the fan and power supply modules in the hot aisle.
• Dual-direction airflow—Airflow direction is determined by the airflow direction of the installed fan modules.
Airflow Requirements
You can identify the airflow direction of each fan and power supply module by its coloring as follows:
• Blue coloring indicates port-side exhaust airflow.
• Burgundy coloring indicates port-side intake airflow.
• White coloring on HVAC/HVDC power supplies indicates dual-direction airflow.
• Gray coloring on DC power supplies indicates port-side exhaust airflow.
• Green coloring on DC power supplies indicates port-side intake airflow.
Note
To prevent the switch from overheating and shutting down, you must position the air intake for the switch in a cold aisle, and all of the fan and power supply modules must have the same direction of airflow (even if their coloring is different). If you must change the airflow direction for the switch, you must shutdown the switch before changing the modules.

Rack and Cabinet Requirements

You can install the following types of racks or cabinets for your switch:
• Standard perforated cabinets
• Solid-walled cabinets with a roof fan tray (bottom-to-top cooling)
• Standard open four-post Telco racks
Work with your cabinet vendors to determine which of their cabinets meet the following requirements or see the Cisco Technical Assistance Center (TAC) for recommendations:
Cisco Nexus 92160YC-X NX-OS Mode Switch Hardware Installation Guide
9

Clearance Requirements

Preparing the Site
• Use a standard 19-inch (48.3-cm), four-post Electronic Industries Alliance (EIA) cabinet or rack with mounting rails that conform to English universal hole spacing per section 1 of the ANSI/EIA-310-D-1992 standard.
• The depth of a four-post rack must be 24 to 32 inches (61.0 to 81.3 cm) between the front and rear mounting rails (for proper mounting of the bottom-support brackets or other mounting hardware).
• Required clearances between the chassis and the edges of its rack or the interior of its cabinet are as follows:
• 4.5 inches (11.4 cm) between the front of the chassis and the interior of the cabinet (required for cabling).
• 3.0 inches (7.6 cm) between the rear of the chassis and the interior of the cabinet (required for airflow in the cabinet if used).
• No clearance is required between the chassis and the sides of the rack or cabinet (no side airflow).
Additionally, you must have power receptacles located within reach of the power cords used with the switch.
Warning
Statement 1048—Rack Stabilization
Stability hazard. The rack stabilizing mechanism must be in place, or the rack must be bolted to the floor before you slide the unit out for servicing. Failure to stabilize the rack can cause the rack to tip over.
Clearance Requirements
You must provide the chassis with adequate clearance between the chassis and any other rack, device, or structure so that you can properly install the chassis, route cables, provide airflow, and maintain the switch. For the clearances required for an installation of this chassis in a four-post rack, see the following figure.
Depth of the chassis5Chassis1
Cisco Nexus 92160YC-X NX-OS Mode Switch Hardware Installation Guide
10
Loading...
+ 46 hidden pages