Cisco LINKSYS WUSB54AG User Manual

A Division of Cisco Systems, Inc.

®

Model No.

USB Network Adapter

Wireless A/G

WUSB54AG (EU/LA/UK)

User Guide

WIRELESS

802.11g

GHz

5

Dual-Band

4

2

,

GHz

802.11a

Wireless A/G USB Network Adapter

Copyright and Trademarks

Specifications are subject to change without notice. Linksys is a registered trademark or trademark of Cisco
Systems, Inc. and/or its affiliates in the U.S. and certain other countries. Copyright © 2005 Cisco Systems, Inc. All
rights reserved. Other brands and product names are trademarks or registered trademarks of their respective
holders.

This User Guide

The User Guide to the Wireless A/G USB Network Adapter has been designed to make understanding networking
easier than ever. Look for the following items when reading this guide:

In addition to these symbols, there are definitions for technical terms that are presented like this:

Also, each figure (diagram, screenshot, or other image) is provided with a figure number and description, like
this:

Figure numbers and descriptions can also be found in the “List of Figures” section in the “Table of Contents”.

This exclamation point means there is a caution or
warning and is something that could damage your
property or the Adapter.

word: definition.

This checkmark means there is a note of interest and
is something you should pay special attention to while
using the Adapter.

This question mark provides you with a reminder about
something you might need to do while using the Adapter.

Figure 0-1: Sample Figure Description

WUSB54AG-EU-LA-UK-UG-50107NC JL

Wireless A/G USB Network Adapter

Table of Contents

Chapter 1: Introduction 1

Welcome 1
What’s in this Guide? 2

Chapter 2: Planning Your Wireless Network 4

Network Topology 4
Roaming 4
Network Layout 4

Chapter 3: Getting to Know the Wireless A/G USB Network Adapter 6

The USB Port 6
The LED Indicators 6

Chapter 4: Setting up the Wireless A/G USB Network Adapter 7

Using the Setup Wizard 7

Chapter 5: Connecting the Wireless A/G USB Network Adapter 12

Connecting the Adapter 12
Using the Adapter’s Wall Mount 13

Chapter 6: Using the Wireless Network Monitor 14

Using the Wireless Network Monitor Icon 14
Accessing the Wireless Network Monitor 15
Link Information 15
Site Survey 18
Profiles 19
Creating a New Profile 20

Appendix A: Troubleshooting 29

Common Problems and Solutions 29
Frequently Asked Questions 30

Appendix B: Wireless Security 33

Security Precautions 33
Security Threats Facing Wireless Networks 33

Appendix C: Windows Help 36
Appendix D: Glossary 37
Appendix E: Specifications 41

Wireless A/G USB Network Adapter

Appendix F: Warranty Information 43
Appendix G: Regulatory Information 44
Appendix H: Contact Information 46

Wireless A/G USB Network Adapter

List of Figures

Figure 3-1: USB Port 6
Figure 3-2: Front Panel 6
Figure 4-1: Setup Wizard’s Welcome Screen 7
Figure 4-2: Setup Wizard’s License Agreement 7
Figure 4-3: Setup Wizard’s Wireless Mode Screen 8
Figure 4-4: Setup Wizard’s Wireless Mode Screen 8
Figure 4-5: Setup Wizard’s Ad-Hoc Mode Settings Screen 9
Figure 4-6: Setup Wizard’s Wireless Security Screen 9
Figure 4-7: Setup Wizard’s Wireless Security - WEP Screen 10
Figure 4-8: Setup Wizard’s Wireless Security - PSK Using TKIP Screen 10
Figure 4-9: Setup Wizard’s Check Settings Screen 11
Figure 4-10: Setup Wizard’s Congratulations Screen 11
Figure 5-1: How the Adapter Connects to Your PC 12
Figure 5-2: Adapter’s USB Port 12
Figure 5-3: PC’s USB Ports 12
Figure 5-4: Using the Wall Mount - Step A 13
Figure 5-5: Using the Wall Mount - Step B 13
Figure 5-6: Using the Wall Mount - Step C 13
Figure 6-1: Wireless Network Monitor Icon 14
Figure 6-2: Windows XP - Use Windows XP Wireless Configuration 14
Figure 6-3: Windows XP - Use Linksys Wireless Network Monitor 14
Figure 6-4: Link Information 15
Figure 6-5: More Information - Wireless Network Status 16
Figure 6-6: More Information-Network Statistics 17
Figure 6-7: Site Survey 18
Figure 6-8: WEP Key Needed for Connection 18
Figure 6-9: PSK (Pre-Shared Key) Needed for Connection 18
Figure 6-10: Profiles 19
Figure 6-11: Import a Profile 19
Figure 6-12: Export a Profile 19

Wireless A/G USB Network Adapter

Figure 6-13: Create a New Profile 20
Figure 6-14: Enter Profile Name 20
Figure 6-15: Network Settings for New Profile 20
Figure 6-16: Wireless Mode for New Profile 21
Figure 6-17: Ad-Hoc Mode Settings for New Profile 21
Figure 6-18: Wireless Security for New Profile 22
Figure 6-19: Wireless Security - WEP for New Profile 22
Figure 6-20: Wireless Security - WPA - Personal for New Profile 23
Figure 6-21: Wireless Security - WPA - Enterprise Encryption Methods for New Profile 24
Figure 6-22: Wireless Security - WPA - Enterprise using EAP - TLS for New Profile 24
Figure 6-23: Wireless Security - WPA - Enterprise using EAP-PEAP for New Profile 25
Figure 6-24: Wireless Security - WPA - Enterprise using EAP-TTLS for New Profile 25
Figure 6-25: Wireless Security - RADIUS using EAP-TLS for New Profile 26
Figure 6-26: Wireless Security - RADIUS using EAP-PEAP for New Profile 26
Figure 6-27: Wireless Security - RADIUS using EAP-TTLS for New Profile 27
Figure 6-28: Confirm New Settings for New Profile 28
Figure 6-29: Congratulations for New Profile 28

1

Chapter 1: Introduction
Welcome

Wireless A/G USB Network Adapter

Chapter 1: Introduction

Welcome

Thank you for choosing the Wireless A/G USB Network Adapter. With this Adapter, your wireless networking
experience will be faster and easier than ever.

Connect your USB-equipped desktop or notebook computer to a wireless network at incredible speeds with the
Linksys Wireless A/G USB Network Adapter. By combining wireless networking with USB 2.0, the Adapter delivers
data rates up to 54Mbps (5 times as fast as 802.11b), without the trouble of opening up the case of your desktop
computer.

To install, simply plug the Adapter into any available USB port. (It's compatible with both USB 1.1 and 2.0 ports,
but 2.0 will yield the fastest speeds.) It gets its power through the USB connection, so no power cord is
necessary. The included Setup Wizard walks you through configuring the Adapter to your wireless network
settings, step by step. The Wireless A/G USB Network Adapter is also compatible with the Wireless-B (802.11b)
network standard as well as the Wireless-A (802.11a) standard. And your wireless communications can be
protected by 128-bit encryption, so your data stays safe.

The Wireless A/G USB Network Adapter's high-performance antenna lets you put your computer almost anywhere
in the building, without the cost and hassle of running cables. Once you're connected, you can keep in touch with
your e-mail, access the Internet, use instant messaging to chat with friends, and share files and other resources
such as printers and hard disk storage space with other computers on the network.

Use the instructions in this Guide to help you install and use the Wireless A/G USB Network Adapter. These
instructions should be all you need to get the most out of the Adapter.

802.11b: a wireless networking standard that
specifies a maximum data transfer rate of 11Mbps
and an operating frequency of 2.4GHz.

adapter: a device that adds network functionality
to your PC.

network: a series of computers or devices
connected for the purpose of data sharing,
storage, and/or transmission between users.

802.11g: a wireless networking standard that
specifies a maximum data transfer rate of 54Mbps
and an operating frequency of 2.4GHz.

2

Chapter 1: Introduction
What’s in this Guide?

Wireless A/G USB Network Adapter

What’s in this Guide?

This user guide covers the steps for setting up and using the Wireless A/G USB Network Adapter.

• Chapter 1: Introduction
This chapter describes the Adapter’s applications and this User Guide.

• Chapter 2: Planning Your Wireless Network
This chapter discusses a few of the basics about wireless networking.

• Chapter 3: Getting to Know the Wireless A/G USB Network Adapter
This chapter describes the physical features of the Adapter.

• Chapter 4: Setting up the Wireless A/G USB Network Adapter
This chapter instructs you on how to run the Adapter’s Setup Wizard and configure the Adapter.

• Chapter 5: Connecting the Wireless A/G USB Network Adapter
This chapter shows you how to connect the Adapter to your PC.

• Chapter 6: Using the Wireless Network Monitor
This chapter explains how to use the Adapter’s Wireless Network Monitor.

• Appendix A: Troubleshooting
This appendix describes some potential problems and solutions, as well as frequently asked questions,
regarding installation and use of the Adapter.

• Appendix B: Wireless Security
This appendix discusses security issues regarding wireless networking and measures you can take to help
protect your wireless network.

• Appendix C: Windows Help
This appendix describes how you can use Windows Help for instructions about networking, such as installing
the TCP/IP protocol.

• Appendix D: Glossary
This appendix gives a brief glossary of terms frequently used in networking.

• Appendix E: Specifications
This appendix provides the Adapter’s technical specifications.

• Appendix F: Warranty Information
This appendix supplies the Adapter’s warranty information.

3

Chapter 1: Introduction
What’s in this Guide?

Wireless A/G USB Network Adapter

• Appendix G: Regulatory Information
This appendix supplies the Adapter’s regulatory information.

• Appendix H: Contact Information
This appendix provides contact information for a variety of Linksys resources, including Technical Support.

4

Chapter 2: Planning Your Wireless Network
Network Topology

Wireless A/G USB Network Adapter

Chapter 2: Planning Your Wireless Network

Network Topology

A wireless network is a group of computers, each equipped with one wireless adapter. Computers in a wireless
network must be configured to share the same radio channel. Several PCs equipped with wireless cards or
adapters can communicate with one another to form an ad-hoc network.

Linksys wireless adapters also provide users access to a wired network when using an access point or wireless
router. An integrated wireless and wired network is called an infrastructure network. Each wireless PC in an
infrastructure network can talk to any computer in a wired network infrastructure via the access point or wireless
router.

An infrastructure configuration extends the accessibility of a wireless PC to a wired network, and can double the
effective wireless transmission range for two wireless adapter PCs. Since an access point is able to forward data
within a network, the effective transmission range in an infrastructure network can be doubled.

Roaming

Infrastructure mode also supports roaming capabilities for mobile users. Roaming means that you can move your
wireless PC within your network and the access points will pick up the wireless PC's signal, provided that they
both share the same channel and SSID.

Choose a feasible radio channel and optimum access point position. Proper access point positioning combined
with a clear radio signal will greatly enhance performance.

Network Layout

Linksys wireless access points and wireless routers have been designed for use with 802.11a, 802.11b, and

802.11g products. With 802.11g products communicating with the 802.11b standard and some products

incorporating both “a” and “g”, products using these standards can communicate with each other.
Access points and wireless routers are compatible with 802.11a, 802.11b and 802.11g adapters, such as the PC

Adapters for your laptop computers, PCI Adapters for your desktop PCs, and USB Adapters for when you want to
enjoy USB connectivity. Wireless products will also communicate with the Wireless PrintServer.

infrastructure: a wireless network that is
bridged to a wired network via an access point.

ad-hoc: a group of wireless devices
communicating directly with each other (peer­to-peer) without the use of an access point.

roaming: the ability to take a wireless device
from one access point's range to another without
losing the connection.

ssid: your wireless network's name.

topology: the physical layout of a network.

5

Chapter 2: Planning Your Wireless Network
Network Layout

Wireless A/G USB Network Adapter

When you wish to connect your wired network with your wireless network, network ports on access points and
wireless routers can be connected to any of Linksys's switches or routers.

With these, and many other, Linksys products, your networking options are limitless. Go to the Linksys website at
www.linksys.com/international for more information about wireless products.

6

Chapter 3: Getting to Know the Wireless A/G USB Network Adapter
The USB Port

Wireless A/G USB Network Adapter

Chapter 3: Getting to Know the Wireless A/G USB Network
Adapter

The USB Port

The Adapter’s USB port is located on the side of the Adapter. Connect the included USB cable to this port and your
PC’s USB port. All power is provided through the USB connection, so a power adapter is not needed.

The LED Indicators

The Adapter's LEDs indicate the status of the Adapter’s power and wireless connection.

Power Green. The Power LED lights up when the Adapter is adequately powered by the USB connection.
Link Green. The Link LED lights up when the Adapter has an active wireless connection. It will flash when

data is transmitted.

Figure 3-1: USB Port

Figure 3-2: Front Panel

7

Chapter 4: Setting up the Wireless A/G USB Network Adapter
Using the Setup Wizard

Wireless A/G USB Network Adapter

Chapter 4: Setting up the Wireless A/G USB Network Adapter

The Wireless A/G USB Network Adapter Setup Wizard will guide you through the installation procedure. The Setup
Wizard will install the driver and Wireless Network Monitor, as well as configure the Adapter.

Using the Setup Wizard

Insert the Setup Wizard CD-ROM into your CD-ROM drive. The Setup Wizard should run automatically, and the

Welcome screen should appear. If it does not, click the Start button and choose Run. In the field that appears,
enter D:\setup.exe (if “D” is the letter of your CD-ROM drive).

On the Welcome screen, you have the following choices:

Install - Click the Install button to begin the software installation process.
User Guide - Click the User Guide button to open the PDF file of this User Guide.
Exit - Click the Exit button to exit the Setup Wizard.

1. To install the Adapter, click the Install button on the Welcome screen.

2. After reading the License Agreement, click the Next button if you agree, or click the Cancel button to end the
installation.

Figure 4-1: Setup Wizard’s W elcome Screen

NOTE: You must run the Setup Wizard before connecting the Adapter

to your computer.

Figure 4-2: Setup Wizard’s License Agreement

8

Chapter 4: Setting up the Wireless A/G USB Network Adapter
Using the Setup Wizard

Wireless A/G USB Network Adapter

3. On the Wireless Mode screen, you will need to select which mode of wireless networking you’ll be using. The
first selection will automatically select between a Wireless-A and a Wireless-G networking mode. The second
selection will chose a Wireless-A network mode only, which only connects to 802.11a networks. The third
selection will chose a Wireless-G networking mode only, which only connects to 802.11g and/or 802.11b
networks.

4. From the Wireless Settings (Advanced) screen, you will need to choose a type of network. Click the
Infrastructure Mode radio button if you want your wireless computers to network with computers on your
wired network using a wireless access point. Click the Ad-Hoc Mode radio button if you want multiple
wireless computers to network directly with each other.

In the SSID field, enter the SSID of your wireless network. The SSID must be identical for all devices in the
network. The default setting is linksys (all lowercase). Click the Next button.

Figure 4-4: Setup Wizard’s Wireless Mode Screen

NOTE: Network SSIDs should be unique to your network and identical for all

devices within the network.

Figure 4-3: Setup Wizard’s Wireless Mode Screen

9

Chapter 4: Setting up the Wireless A/G USB Network Adapter
Using the Setup Wizard

Wireless A/G USB Network Adapter

5. If you chose Infrastructure Mode, go to Step 6 now. If you chose Ad-Hoc Mode , select the correct operating
channel for your network. Then, select the Network Mode from the drop-down menu. Click the Next button,
and go to Step 6. Click the Back button to change any settings.

Channel - The channel you choose should match the channel set on the other devices in your wireless
network. If you are unsure about which channel to use, select the default channel.

Network Mode - Select Mixed Mode if you want to allow Wireless-G and Wireless-B computers on the
network, even though network speeds will be reduced. For maximum speed, select G-Only Mode; however,
no Wireless-B users will be allowed on the network.

6. Select the Encryption method you want to use: WEP or WPA - Personal. WEP stands for Wired Equivalent
Privacy.

If you don’t want to use encryption, select Disabled and then click the Next button to continue. Proceed to
Step 8.

Click the Next button to continue or the Back button to return to the previous screen.

Figure 4-6: Setup Wizard’s Wireless Security Scr een

NOTE: More encryption options are available when using the Wireless Network

Monitor. See “Chapter 6: Using the Wireless Network Monitor” for these options.

Figure 4-5: Setup Wizard’s Ad-Hoc Mode Settings Screen

10

Chapter 4: Setting up the Wireless A/G USB Network Adapter
Using the Setup Wizard

Wireless A/G USB Network Adapter

7. Proceed to the appropriate section for your security method: WEP or WPA - Personal.

WEP

WEP - Select 64-bit or 128-bit encryption from the drop-down menu, and enter a passphrase or WEP key.
Passphrase - Enter a passphrase in the Passphrase field, so a WEP key is automatically generated. It is case-

sensitive and should not be longer than 16 alphanumeric characters. This passphrase must match the
passphrase of your other wireless network devices and is compatible with Linksys wireless products only. (If
you have any non-Linksys wireless products, enter the WEP key manually on those products.)

WEP Key - The WEP key you enter must match the WEP key of your wireless network. For 64-bit encryption,
enter exactly 10 hexadecimal characters. For 128-bit encryption, enter exactly 26 hexadecimal characters.
Valid hexadecimal characters are “0” to “9” and “A” to “F”.

Advanced Users
TX Key - The default transmit key number is 1. If your network’s access point or wireless router uses transmit

key number 2, 3, or 4, select the appropriate number from the TX Key drop-down box.
Authentication -The default is set to Auto, so it will auto-detect for Shared Key or Open System

authentication. For Shared Key authentication, both the sender and the recipient share a WEP key for
authentication. For Open System authentication, the sender and the recipient do not share a WEP key for
authentication. If you are not sure which authentication method to select, keep the default, Auto.

Click the Next button to continue. Click the Back button to return to the previous screen.

WPA - Personal

WPA - Personal offers two encryption methods, TKIP and AES, with dynamic encryption keys. Select the type
of algorithm, TKIP or AES, for the Encryption Type. Then enter a Passphrase that is 8-63 characters in length.

Encryption - Select the type of algorithm you want to use, TKIP or AES, for the Encryption Type.
Passphrase - Enter a Passphrase, also called a Pre-Shared Key, of 8-63 characters in the Passphrase field.

The longer and more complex your Passphrase is, the more secure your network will be.
Click the Next button to continue. Click the Back button to return to the previous screen.

Figure 4-8: Setup Wizard’ s Wireless Security -

PSK Using TKIP Screen

Figure 4-7: Setup Wizard’s Wireless Security -

WEP Screen

11

Chapter 4: Setting up the Wireless A/G USB Network Adapter
Using the Setup Wizard

Wireless A/G USB Network Adapter

8. The Setup Wizard will ask you to review your settings before it starts to install files. Click Next if you are
satisfied with your settings, or click Back to change any settings.

9. After the software has been successfully installed, the Congratulations screen will appear. Click the Exit
button.

Proceed to “Chapter 5: Connecting the Wireless A/G USB Network Adapter.”

Figure 4-9: Setup Wizard’s Check Settings Screen

Figure 4-10: Setup Wizard’s Congratulations Screen

12

Chapter 5: Connecting the Wireless A/G USB Network Adapter
Connecting the Adapter

Wireless A/G USB Network Adapter

Chapter 5: Connecting the Wireless A/G USB Network Adapter

Connecting the Adapter

1. Connect one end of the included USB cable to the Adapter’s USB port.

2. Connect the other end of the cable to one of the USB ports on your computer.

3. The Power LED should light up when the Adapter is plugged in.

4. Raise the antenna. Make sure the antenna points straight up into the air , at a 90º angle from the Adapter. This
will ensure optimum wireless operating range and performance.

Congratulations! The installation of the Wireless A/G Network Adapter is complete.

If you want to check the link information, search for available wireless networks, or make additional

configuration changes, go to “Chapter 6: Using the Wireless Network Monitor.”

Figure 5-1: How the Adapter Connects to Your PC

NOTE: You must run the Setup Wizard before connecting the Adapter.

Figure 5-2: Adapter’s USB Port

Figure 5-3: PC’s USB Ports

NOTE: If you want to attach the Adapter to your wall, go to the next section,

“Using the Adapter’s Wall Mount,” before proceeding to “Chapter 6: Using the
Wireless Network Monitor.”

13

Chapter 5: Connecting the Wireless A/G USB Network Adapter
Using the Adapter’s Wall Mount

Wireless A/G USB Network Adapter

Using the Adapter’s Wall Mount

The Adapter’s Wall Mount allows you to easily attach the Adapter to your wall for better reception and more
convenient placement.

1. Attach the separate adhesive strip of velcro to the wall where you will be mounting the Adapter.

2. To attach the W all Mount to the Adapter , slide the W all Mount into the grooves on the back panel of Adapter , as
shown in Steps A, B, and C.

3. Using the velcro strip on the Adapter’s Wall Mount, attach the Adapter to the velcro strip on your wall.

Congratulations! The installation of the Wireless A/G Network Adapter is complete.

If you want to check the link information, search for available wireless networks, or make additional

configuration changes, go to “Chapter 6: Using the Wireless Network Monitor.”

Figure 5-4: Using the Wall Mount - Step A

Figure 5-5: Using the Wall Mount - Step B

Figure 5-6: Using the Wall Mount - Step C

14

Chapter 6: Using the Wireless Network Monitor
Using the Wireless Network Monitor Icon

Wireless A/G USB Network Adapter

Chapter 6: Using the Wireless Network Monitor

Use the Wireless Network Monitor to check the link information, search for available wireless networks, or create
profiles that hold different configuration settings.

Using the Wireless Network Monitor Icon

After installing the Adapter, the Wireless A/G USB Network Adapter Wireless Monitor icon will appear in your
system tray. If the Wireless Network Monitor is enabled, then the icon will be green. If the Wireless Network
Monitor is disabled or the Adapter is not connected, then the icon will be gray.

If you right-click the icon, you will see these choices:

• About - Click About to view the version information for the driver and Wireless Network Monitor.

• Use Windows XP Wireless Configuration (Windows XP only) - If your computer is running Windows XP, then
this choice will be available. If you want to use Windows XP Wireless Zero Configuration to control the
Adapter—instead of using the Wireless Network Monitor—then select Use Windows XP Wireless
Configuration.

If you want to switch back to the Wireless Network Monitor, right-click the Wireless Network Monitor icon,
and select Use Linksys Wireless Network Monitor.

• Turn Monitor on - Select Turn Monitor on to enable the Wireless Network Monitor.

• Turn Monitor off - Select Turn Monitor off to disable the Wireless Network Monitor.

Figure 6-1: Wireless Network Monitor Icon

NOTE: For more information about Wireless Zero Configuration, refer

to Windows Help.

Figure 6-2: Windows XP - Use Windows XP

Wireless Configuration

Figure 6-3: Windows XP - Use Linksys

Wireless Network Monitor

15

Chapter 6: Using the Wireless Network Monitor
Accessing the Wireless Network Monitor

Wireless A/G USB Network Adapter

Accessing the Wireless Network Monitor

Besides selecting Turn on when you right-click the icon, you can also double-click the Wireless Network
Monitor icon to activate the Wireless Network Monitor. Then the Link Information screen will appear. From this

screen, you can find out how strong the current wireless signal is and how good the connection’s quality is. You
can also click the More Information button to view additional status information about the current wireless
connection. To search for available wireless networks, click the Site Survey tab. To perform configuration
changes, click the Profiles tab.

Link Information

The Link Information screen displays network mode, signal strength, and link quality information about the
current connection. It also provides a button to click for additional status information.

Ad-Hoc Mode or Infrastructure Mode - The screen indicates whether the Adapter is currently working in ad­hoc or infrastructure mode.

Signal Strength - The Signal Strength bar indicates signal strength.
Link Quality - The Link Quality bar indicates the quality of the wireless network connection.

Click the More Information button to view additional information about the wireless network connection.
Clicking the More Information button displays the Wireless Network Status screen, which displays more infor-

mation about the Adapter’s connection.

Figure 6-4: Link Information

16

Chapter 6: Using the Wireless Network Monitor
Link Information

Wireless A/G USB Network Adapter

Wireless Network Status

The Wireless Network Status screen provides information on your current network settings.

Status - The status of the wireless network connection.
SSID - This is the unique name of the wireless network.
Wireless Mode - The mode of the wireless network currently in use is displayed here.
Transfer Rate - The data transfer rate of the current connection is shown here.
Channel - This is the channel to which the wireless network devices are set.
WEP - The status of the wireless security feature is displayed here.
Authentication - This is your wireless network’s authentication method.
IP Address - The IP Address of the Adapter is displayed here.
Subnet Mask - The Subnet Mask of the Adapter is shown here.
Default Gateway - The Default Gateway address of the Adapter is displayed here.
DNS - This is the DNS address of the Adapter.
DHCP Client - This displays the Adapter’s status as a DHCP client.
MAC - The MAC address of the wireless network’s access point is shown here.

Signal Strength - The Signal Strength bar indicates the signal strength.
Link Quality - The Link Quality bar indicates the quality of the wireless network connection.

Click the Statistics button to go to the Wireless Network Statistics screen. Click the Back button to return to the
initial Link Information screen. Click the Save to Profile button to save the currently active connection settings to
a profile.

Figure 6-5: More Information - Wireless Network Status

17

Chapter 6: Using the Wireless Network Monitor
Link Information

Wireless A/G USB Network Adapter

Wireless Network Statistics

The Wireless Networks Statistics screen provides statistics on your current network settings.
Transmit Rate - This is the data transfer rate of the current connection. (In Auto mode, the Adapter dynamically

shifts to the fastest data transfer rate possible at any given time.)

Receive Rate - This is the rate at which data is received.
Packets Received - This shows the packets received by the Adapter, in real time, since connecting to the

Wireless Network or since the Refresh Statistics button was last pressed.
Packets Transmitted - This shows the packets transmitted from the Adapter, in real time, since connecting to

the Wireless Network or since the Refresh Statistics button was last pressed.
Bytes Received - This shows the bytes received by the Adapter, in real time, since connecting to the Wireless

Network or since the Refresh Statistics button was last pressed.
Bytes Transmitted - This shows the bytes transmitted from the Adapter, in real time, since connecting to the

Wireless Network or since the Refresh Statistics button was last pressed.
Noise Level - This shows the level of background noise affecting the wireless signal. A lower reading translates

into a higher quality signal.

Signal Strength - This is the intensity of the wireless signal received by the Adapter.
Up Time - This indicates the length of the most recent connection to a wireless network.
Total Up Time - This indicates the cumulative total of the Adapter’s connection time.
Driver Version - This shows the version of the Adapter’s driver.
Signal Strength - The Signal Strength bar indicates the signal strength.
Link Quality - The Link Quality bar indicates the quality of the wireless network connection.

Click the Back button to return to the initial Link Information screen. Click the Status button to go to the Wireless
Network Status screen. Click the Save to Profile button to save the currently active connection settings to a

profile. Click the Refresh Statistics button to update or reset the statistics. The Wireless Network Monitor will
update the Transmit Rate , Receive Rate, Noise Level, and Signal Strength statistics. At the same time, the Packets
Received and Transmitted counts, Bytes Received and Transmitted counts, and Up Time statistic will be reset to
zero. (The Total Up Time statistic will not be reset.)

Figure 6-6: More Information-Network Statistics

18

Chapter 6: Using the Wireless Network Monitor
Site Survey

Wireless A/G USB Network Adapter

Site Survey

The Site Survey screen displays a list of infrastructure and ad-hoc networks available for connection in the table
on the left. This table shows the network’s SSID, Channel, and the quality of the wireless signal the Adapter is
receiving. You may click SSID, CH (Channel), or Signal, to sort by that field.

SSID - The SSID or unique name of the wireless network is displayed here.
CH - This is the channel setting that the network uses.
Signal - This is the percentage of signal strength, from 0 to 100%.
Type - This is the type of network: A, B, or G.

Site Information

For each network selected, the following settings are listed:

SSID - This the SSID or unique name of the wireless network.
Wireless Mode - This is the mode of the wireless network currently in use.
Channel - This is the channel to which the wireless network devices are set.
Encryption - The status of the wireless security feature is displayed here.
MAC - The MAC address of the wireless network’s access point is displayed here.
Refresh - Click the Refresh button to perform a new search for wireless devices.
Connect - To connect to one of the networks on the list, select the wireless network, and click the Connect

button. If the network has encryption enabled, then you will see a new screen appear.
From the Security drop-down menu, select the network’s encryption method, WEP or PSK.
If you selected WEP, then you will see the WEP Key Needed for Connection screen. Select the appropriate level of

WEP encryption, 64-bit or 128-bit. Then enter the network’s Passphrase or WEP Key. Click the Connect button.
To cancel the connection, click the Cancel button.

If you selected PSK, then you will see the PSK (Pre-Shared Key) Needed for Connection screen. Select the
appropriate encryption type, TKIP or AES. Then enter the network’s Passphrase or Pre-Shared Key in the

Passphrase field. Then click the Connect button. To cancel the connection, click the Cancel button.

Figure 6-8: WEP Key Needed for Connection

Figure 6-9: PSK (Pre-Shared Key) Needed for Connection

Figure 6-7: Site Survey

19

Chapter 6: Using the Wireless Network Monitor
Profiles

Wireless A/G USB Network Adapter

Profiles

The Profiles screen lets you save different configuration profiles for different network setups. The table on the left
displays a list of infrastructure and ad-hoc networks available for connection. This table shows the network’s
profile name, the network’s SSID, and the type of network, as set in the connection profile.

Profile Information

For each profile selected, the following are listed:

Wireless Mode - This is the mode of the wireless network currently in use.
Transfer Rate - The Adapter is set to Auto mode, so it will dynamically shift to the fastest data transfer rate

possible at any given time.

Channel - This is the channel to which the wireless network devices are set.
Encryption - The status of the wireless security feature is displayed here.
Authentication - The authentication setting for the network is shown here.
Connect - To connect to a wireless network using a specific profile, select the profile, and click the Connect

button.

New - Click the New button to create a new profile. See the next section, “Creating a New Profile,” for detailed
instructions.

Edit - Select a profile, and click the Edit button to change an existing profile.
Import - Click the Import button to import a profile that has been saved in another location. Select the

appropriate file, and click the Open button.
Export - Select the profile you want to save in a different location, and click the Export button. Direct Windows to

the appropriate folder, and click the OK button.
Delete - Click the Delete button to delete a profile.

Figure 6-10: Profiles

Figure 6-11: Import a Profile

Figure 6-12: Export a Prof ile

NOTE: If you want to export more than one profile, you have to export them one at a time.

20

Chapter 6: Using the Wireless Network Monitor
Creating a New Profile

Wireless A/G USB Network Adapter

Creating a New Profile

1. On the Profiles screen, click the New button to create a new profile.

2. Enter a name for the new profile, and click the OK button. Click the Cancel button to return to the Profiles
screen without entering a name.

3. The Network Settings screen will appear. If your network has a router or other DHCP server, click the radio
button next to Obtain network settings automatically (DHCP). Click the Next button to continue, or click
the Cancel button to return to the Profiles screen.

If your network does not have a DHCP server, click the radio button next to Specify the network settings.
Enter an IP Address, Subnet Mask, Default Gateway , and DNS address appropriate for your network. You must
specify the IP Address and Subnet Mask on this screen. If you are unsure about the Default Gateway and DNS
address, leave these fields empty. Click the Next button to continue, or click the Cancel button to return to
the Profiles screen.

IP Address - This IP Address must be unique to your network.
Subnet Mask - The Adapter’s Subnet Mask must be the same as your wired network’s Subnet Mask.
Default Gateway - Enter the IP address of your network’s Gateway here.
DNS 1 and DNS 2 - Enter the DNS address of your wired Ethernet network here.

Figure 6-13: Create a New Profile

Figure 6-14: Enter Profile Name

Figure 6-15: Network Settings for New Profile

21

Chapter 6: Using the Wireless Network Monitor
Creating a New Profile

Wireless A/G USB Network Adapter

4. The Wireless Mode screen shows a choice of two wireless modes. Click the Infrastructure Mode radio
button if you want your wireless computers to communicate with computers on your wired network via a
wireless access point. Click the Ad-Hoc Mode radio button if you want multiple wireless computers to
communicate directly with each other. Enter the SSID for your network.

Click the Next button to continue or the Back button to return to the previous screen.
Infrastructure Mode - This mode allows wireless and wired networks to communicate through an access

point.
Ad-Hoc Mode - This mode allows wireless-equipped computers to communicate directly with each other. No

access point is used.
SSID - This is the network name. It must be used for all the devices in your wireless network. It is case-

sensitive. It should be a unique name to help prevent others from entering your network.

5. The Ad-Hoc Mode Settings screen will appear. If you chose Infrastructure Mode, go to Step 6 now. If you
chose Ad-Hoc Mode, select the correct operating channel for your network from the Channel drop-down
menu. Then, select the Network Mode from the drop-down menu. Click the Next button, and go to Step 6.
Click the Back button to change any settings.

Channel - The channel you choose should match the channel set on the other devices in your wireless
network. If you are unsure about which channel to use, select the default channel.

Network Mode - Select Mixed Mode, and both Wireless-G and Wireless-B computers will be allowed on the
network, but the speed may be reduced. Select G-Only Mode for maximum speed, but no Wireless-B users
will be allowed on the network.

Figure 6-16: Wireless Mode for New Profile

Figure 6-17: Ad-Hoc Mode Settings for New Profile

22

Chapter 6: Using the Wireless Network Monitor
Creating a New Profile

Wireless A/G USB Network Adapter

6. Select the method of security you want to use: WEP, WPA - Personal, WPA - Enterprise, or RADIUS. WEP
stands for Wired Equivalent Privacy, and PSK stands for Pre-Shared Key. RADIUS stands for Remote
Authentication Dial-In User Service.

If you don’t want to use encryption, select Disabled and then click the Next button to continue. Proceed to
Step 8.

Click the Next button to continue or the Back button to return to the previous screen.

7. Proceed to the appropriate section for your security method: WEP, PSK, PSK-RADIUS, or RADIUS.

WEP

WEP - Select 64-bit or 128-bit encryption from the drop-down menu, and enter a passphrase or WEP key.
Passphrase - Enter a passphrase in the Passphrase field, so a WEP key is automatically generated. It is

case-sensitive and should not be longer than 16 alphanumeric characters. This passphrase must match the
passphrase of your other wireless network devices and is compatible with Linksys wireless products only. (If
you have any non-Linksys wireless products, enter the WEP key manually on those products.)

WEP Key - The WEP key you enter must match the WEP key of your wireless network. For 64-bit encryption,
enter exactly 10 hexadecimal characters. For 128-bit encryption, enter exactly 26 hexadecimal characters.
Valid hexadecimal characters are “0” to “9” and “A” to “F”.

Advanced Users
TX Key - The default transmit key number is 1. If your network’s access point or wireless router uses transmit

key number 2, 3, or 4, select the appropriate number from the TX Key drop-down box.
Authentication -The default is set to Auto, so it will auto-detect for Shared Key or Open System

authentication. For Shared Key authentication, both the sender and the recipient share a WEP key for
authentication. For Open System authentication, the sender and the recipient do not share a WEP key for
authentication. If you are not sure which authentication method to select, keep the default, Auto.

Click the Next button to continue. Click the Back button to return to the previous screen.

Figure 6-18: Wireless Security for New Profile

Figure 6-19: Wireless Security - WEP for New Profile

NOTE: If your network is using WPA-Personal or WPA-PSK security, then

select PSK. If your network is using WPA-Enterprise or WPA-RADIUS security,
then select PSK + RADIUS.

23

Chapter 6: Using the Wireless Network Monitor
Creating a New Profile

Wireless A/G USB Network Adapter

WPA - Personal

WPA - Personal offers two encryption methods, TKIP and AES, with dynamic encryption keys. Select the type
of algorithm, TKIP or AES, for the Encryption Type. Then enter a Passphrase that is 8-63 characters in length.

Encryption - Select the type of algorithm you want to use, TKIP or AES, for the Encryption Type.
Passphrase - Enter a Passphrase, also called a Pre-Shared Key, of 8-63 characters in the Passphrase field.

The longer and more complex your Passphrase is, the more secure your network will be.
Click the Next button to continue. Click the Back button to return to the previous screen.

Figure 6-20: Wireless Security - WPA - Personal

for New Profile

24

Chapter 6: Using the Wireless Network Monitor
Creating a New Profile

Wireless A/G USB Network Adapter

WPA - Enterprise

WPA - Enterprise features a Pre-Shared Key used in coordination with a RADIUS server. (This should only be
used when a RADIUS server is connected to the Router.) WPA - Enterprise offers two encryption methods,
TKIP and AES, with dynamic encryption keys, as well as three authentication methods, EAP-TLS, EAP-PEAP
and EAP-TTLS.

After selecting WPA - Enterprise, choose an encryption method: TKIP or AES.
The next screen that appears will require you to select the authentication method your network is using:

EAP-TLS, EAP-PEAP, or EAP-TTLS.

EAP-TLS

If you select EAP-TLS, enter the login name of your wireless network in the Login Name field. Enter the name
of the authentication server in the Server Name field. From the Certificate drop-down menu, select the
certificate you have installed to authenticate you on your wireless network. Select Validate server
certificate to make sure that the certificate for the server is valid.

Click the Next button to continue. Click the Back button to return to the previous screen.

Figure 6-21: Wireless Security - WPA - Enterprise

Encryption Methods for New Profile

Figure 6-22: Wireless Security - WPA - Enterprise

using EAP - TLS for New Profile

25

Chapter 6: Using the Wireless Network Monitor
Creating a New Profile

Wireless A/G USB Network Adapter

EAP-PEAP

If you select EAP-PEAP, enter the login name of your wireless network in the Login Name field. Enter the
password of your wireless network in the Password field. Enter the name of the authentication server in the
Server Name field. From the Certificate drop-down menu, select the certificate installed to authenticate you
on your wireless network. Select the type of encryption, TKIP or AES, for the Encryption field.

Click the Next button to continue. Click the Back button to return to the previous screen.

EAP-TTLS

Enter the Login name of your wireless network in the Login Name field. Enter the password of your wireless
network in the Password field. Select Validate server certificate to make sure that the certificate for the
server is valid. Select the TTLS Protocol from the drop-down menu.

Click the Next button to continue. Click the Back button to return to the previous screen.

Figure 6-23: Wireless Security - WPA - Enterprise

using EAP-PEAP for New Profile

Figure 6-24: Wireless Security - WPA - Enterprise

using EAP-TTLS for New Profile

26

Chapter 6: Using the Wireless Network Monitor
Creating a New Profile

Wireless A/G USB Network Adapter

RADIUS

RADIUS features use of a RADIUS server . (This should only be used when a RADIUS s erver is connected to the
Router.) RADIUS offers two authentication types: EAP-TLS and EAP-PEAP.

Authentication - Select the authentication method your network is using, EAP-TLS or EAP-PEAP.

EAP-TLS

If you select EAP-TLS, enter the login name of your wireless network in the Login Name field. Enter the name
of the authentication server in the Server Name field. From the Certificate drop-down menu, select the
certificate installed to authenticate you on your wireless network.

Click the Next button to continue. Click the Back button to return to the previous screen.

EAP-PEAP

If you select EAP-PEAP, enter the login name of your wireless network in the Login Name field. Enter the
password of your wireless network in the Password field. Enter the name of the authentication server in the
Server Name field. From the Certificate drop-down menu, select the certificate installed to authenticate you
on your wireless network.

Click the Next button to continue. Click the Back button to return to the previous screen.

Figure 6-25: Wireless Security - RADIUS using

EAP-TLS for New Profile

Figure 6-26: Wireless Security - RADIUS using

EAP-PEAP for New Profile

27

Chapter 6: Using the Wireless Network Monitor
Creating a New Profile

Wireless A/G USB Network Adapter

EAP-TTLS

Enter the Login name of your wireless network in the Login Name field. Enter the password of your wireless
network in the Password field. Select Validate server certificate to make sure that the certificate for the
server is valid. Select the TTLS Protocol from the drop-down menu.

Click the Next button to continue. Click the Back button to return to the previous screen.

Figure 6-27: Wireless Security - RADIUS using

EAP-TTLS for New Profile

28

Chapter 6: Using the Wireless Network Monitor
Creating a New Profile

Wireless A/G USB Network Adapter

8. The Confirm New Settings screen will appear next and show the new settings. T o save the new settings, click
the Save button. To edit the new settings, click the Back button. To exit the Wireless Network Monitor, click
Exit.

9. The Congratulations screen will appear next. Click Connect to Network to implement the new settings
immediately and return to the Link Information screen. Click Return to Profiles Screen to keep the current
settings active and return to the Profiles screen.

You have successfully created a connection profile.

Figure 6-28: Confirm New Settings for New Profile

Figure 6-29: Congratulations for New Profile

29

Appendix A: Troubleshooting
Common Problems and Solutions

Wireless A/G USB Network Adapter

Appendix A: Troubleshooting

This appendix consists of two parts: “Common Problems and Solutions” and “Frequently Asked Questions.” This
appendix provides solutions to problems that may occur during the installation and operation of the Wireless A/G
USB Network Adapter . Read the description below to solve your problems. If you can't find an answer here, check
the Linksys website at www.linksys.com/international.

Common Problems and Solutions

1. My computer does not recognize the Wireless A/G USB Network Adapter.

Follow the steps below until the problem is solved:

• Make sure the Adapter is properly connected to the PC’s USB port.

• Make sure that the USB Controller is enabled in the BIOS. Refer to the documentation for your PC’s

motherboard.

2. The Wireless A/G USB Network Adapter does not work properly.

Follow the steps below until the problem is solved:

• Reinsert the Wireless A/G USB Network Adapter into the notebook or desktop’s USB port.

• Click Start and select Settings. Click Control Panel. Double-click System. Click the Hardware tab . Click

the Device Manager button. You will find the Wireless A/G USB Network Adapter if it is installed
successfully. If not, disconnect the Adapter and uninstall the driver software from your PC. Then restart
your PC and repeat the software and hardware installation specified in this User Guide.

3. I cannot communicate with the other computers linked via Ethernet in the Infrastructure
configuration.

Follow the steps below until the problem is solved:

• Make sure that the notebook or desktop PC is powered on.

• Make sure that the Wireless A/G USB Network Adapter is configured with the same SSID and security

settings as the other computers in the Infrastructure configuration.

30

Appendix A: Troubleshooting
Frequently Asked Questions

Wireless A/G USB Network Adapter

Frequently Asked Questions

Can I run an application from a remote computer over the wireless network?

This will depend on whether or not the application is designed to be used over a network. Consult the
application’s user guide to determine if it supports operation over a network.

Can I play computer games with other members of the wireless network?

Yes, as long as the game supports multiple players over a LAN (local area network). Refer to the game’s user
guide for more information.

What is the IEEE 802.11b standard?

It is one of the IEEE standards for wireless networks. The 802.11b standard allows wireless networking hardware
from different manufacturers to communicate, provided that the hardware complies with the 802.11b standard.
The 802.11b standard states a maximum data transfer rate of 11Mbps and an operating frequency of 2.4GHz.

What is the IEEE 802.11g standard?

It is one of the IEEE standards for wireless networks. The 802.11g standard allows wireless networking hardware
from different manufacturers to communicate, provided that the hardware complies with the 802.11g standard.
The 802.11g standard states a maximum data transfer rate of 54Mbps and an operating frequency of 2.4GHz.

What IEEE 802.11b features are supported?

The product supports the following IEEE 802.11b functions:

• CSMA/CA plus Acknowledge protocol

• Multi-Channel Roaming

• Automatic Rate Selection

• RTS/CTS feature

• Fragmentation

• Power Management

What IEEE 802.11g features are supported?

The product supports the following IEEE 802.11g functions:

• CSMA/CA plus Acknowledge protocol

• OFDM protocol

• Multi-Channel Roaming

• Automatic Rate Selection

• RTS/CTS feature

• Fragmentation

• Power Management

fragmentation: breaking a packet into smaller units
when transmitting over a network medium that cannot
support the original size of the packet.

mbps: one million bits per second; a unit of
measurement for data transmission.

31

Appendix A: Troubleshooting
Frequently Asked Questions

Wireless A/G USB Network Adapter

What is ad-hoc mode?

When a wireless network is set to ad-hoc mode, the wireless-equipped computers are configured to
communicate directly with each other. The ad-hoc wireless network will not communicate with any wired
network.

What is infrastructure mode?

When a wireless network is set to infrastructure mode, the wireless network is configured to communicate with a
wired network through a wireless access point.

What is roaming?

Roaming is the ability of a portable computer user to communicate continuously while moving freely throughout
an area greater than that covered by a single access point. Before using the roaming function, the workstation
must make sure that it is the same channel number with the access point of dedicated coverage area.

To achieve true seamless connectivity, the wireless LAN must incorporate a number of different functions. Each
node and access point, for example, must always acknowledge receipt of each message. Each node must
maintain contact with the wireless network even when not actually transmitting data. Achieving these functions
simultaneously requires a dynamic RF networking technology that links access points and nodes. In such a
system, the user’s end node undertakes a search for the best possible access to the system. First, it evaluates
such factors as signal strength and quality, as well as the message load currently being carried by each access
point and the distance of each access point to the wired backbone. Based on that information, the node next
selects the right access point and registers its address. Communications between end node and host computer
can then be transmitted up and down the backbone.

As the user moves on, the end node’s RF transmitter regularly checks the system to determine whether it is in
touch with the original access point or whether it should seek a new one. When a node no longer receives
acknowledgment from its original access point, it undertakes a new search. Upon finding a new access point, it
then re-registers, and the communication process continues.

What is ISM band?

The FCC and their counterparts outside of the U.S. have set aside bandwidth for unlicensed use in the ISM
(Industrial, Scientific and Medical) band. Spectrum in the vicinity of 2.4 GHz, in particular, is being made available
worldwide. This presents a truly revolutionary opportunity to place convenient high-speed wireless capabilities in
the hands of users around the globe.

What is Spread Spectrum?

Spread Spectrum technology is a wideband radio frequency technique developed by the military for use in
reliable, secure, mission-critical communications systems. It is designed to trade off bandwidth efficiency for
reliability, integrity, and security. In other words, more bandwidth is consumed than in the case of narrowband
transmission, but the trade-off produces a signal that is, in effect, louder and thus easier to detect, provided that

ism band: radio bandwidth utilized in wireless transmissions.

spread spectrum: wideband radio frequency technique

used for more reliable and secure data transmission.

32

Appendix A: Troubleshooting
Frequently Asked Questions

Wireless A/G USB Network Adapter

the receiver knows the parameters of the spread-spectrum signal being broadcast. If a receiver is not tuned to
the right frequency, a spread-spectrum signal looks like background noise. There are two main alternatives,
Direct Sequence Spread Spectrum (DSSS) and Frequency Hopping Spread Spectrum (FHSS).

What is DSSS? What is FHSS? And what are their differences?

Frequency-Hopping Spread-Spectrum (FHSS) uses a narrowband carrier that changes frequency in a pattern that
is known to both transmitter and receiver. Properly synchronized, the net effect is to maintain a single logical
channel. To an unintended receiver, FHSS appears to be short-duration impulse noise. Direct-Sequence Spread­Spectrum (DSSS) generates a redundant bit pattern for each bit to be transmitted. This bit pattern is called a chip
(or chipping code). The longer the chip, the greater the probability that the original data can be recovered. Even if
one or more bits in the chip are damaged during transmission, statistical techniques embedded in the radio can
recover the original data without the need for retransmission. To an unintended receiver, DSSS appears as low
power wideband noise and is rejected (ignored) by most narrowband receivers.

Would the information be intercepted while transmitting on air?

WLAN features two-fold protection in security. On the hardware side, as with Direct Sequence Spread Spectrum
technology, it has the inherent security feature of scrambling. On the software side, WLAN offers the encryption
function (WEP) to enhance security and access control.

What is WEP?

WEP is Wired Equivalent Privacy, a data privacy mechanism based on a shared key algorithm, as described in the
IEEE 802.11 standard. For more information, refer to “Appendix B: Wireless Security.”

What is WPA?

WPA is Wi-Fi Protected Access, a wireless security protocol that can be used in conjunction with a RADIUS server.
For more information, refer to “Appendix B: Wireless Security.”

What is RADIUS?

RADIUS is Remote Authentication Dial-In User Service, which uses an authentication server to control network
access. For more information, refer to “Appendix B: Wireless Security.”

dsss: Frequency transmission with a redundant bit
pattern resulting in a lower probability of information
being lost in transit.

33

Wireless Security

Security Precautions

Wireless A/G USB Network Adapter

Appendix B: Wireless Security

Linksys wants to make wireless networking as safe and easy for you as possible. The current generation of
Linksys products provide several network security features, but they require specific action on your part for
implementation. So, keep the following in mind whenever you are setting up or using your wireless network.

Security Precautions

The following is a complete list of security precautions to take (as shown in this User Guide) (at least steps 1
through 5 should be followed):

1. Change the default SSID.

2. Disable SSID Broadcast.

3. Change the default password for the Administrator account.

4. Enable MAC Address Filtering.

5. Change the SSID periodically.

6. Use the highest encryption algorithm possible. Use WPA if it is available. Please note that this may reduce
your network performance.

7. Change the WEP encryption keys periodically.

To ensure network security, steps one through five should be followed, at least.

Security Threats Facing Wireless Networks

Wireless networks are easy to find. Hackers know that in order to join a wireless network, wireless networking
products first listen for “beacon messages”. These messages can be easily decrypted and contain much of the
network’s information, such as the network’s SSID (Service Set Identifier). Here are the steps you can take:

Change the administrator’s password regularly. With every wireless networking device you use, keep in mind
that network settings (SSID, WEP keys, etc.) are stored in its firmware. Your network administrator is the only
person who can change network settings. If a hacker gets a hold of the administrator’s password, he, too, can
change those settings. So, make it harder for a hacker to get that information. Change the administrator’s
password regularly.

NOTE: Some of these security features are
available only through the network router or
access point. Refer to the router or access
point’s documentation for more information.

34

Wireless Security

Security Threats Facing Wireless Networks

Wireless A/G USB Network Adapter

SSID. There are several things to keep in mind about the SSID:

1. Disable Broadcast

2. Make it unique

3. Change it often

Most wireless networking devices will give you the option of broadcasting the SSID. While this option may be
more convenient, it allows anyone to log into your wireless network. This includes hackers. So, don’t broadcast
the SSID.

Wireless networking products come with a default SSID set by the factory. (The Linksys default SSID is “linksys”.)
Hackers know these defaults and can check these against your network. Change your SSID to something unique
and not something related to your company or the networking products you use.

Change your SSID regularly so that any hackers who have gained access to your wireless network will have to
start from the beginning in trying to break in.

MAC Addresses. Enable MAC Address filtering. MAC Address filtering will allow you to provide access to only
those wireless nodes with certain MAC Addresses. This makes it harder for a hacker to access your network with
a random MAC Address.

WEP Encryption. Wired Equivalent Privacy (WEP) is often looked upon as a cure-all for wireless security
concerns. This is overstating WEP’s ability. Again, this can only provide enough security to make a hacker’s job
more difficult.

There are several ways that WEP can be maximized:

1. Use the highest level of encryption possible

2. Use “Shared Key” authentication

3. Change your WEP key regularly

WPA. Wi-Fi Protected Access (WPA) is the newest and best available standard in Wi-Fi security. Two modes are
available: Pre-Shared Key and RADIUS. Pre-Shared Key gives you a choice of two encryption methods: TKIP
(Temporal Key Integrity Protocol), which utilizes a stronger encryption method and incorporates Message
Integrity Code (MIC) to provide protection against hackers, and AES (Advanced Encryption System), which utilizes
a symmetric 128-Bit block data encryption. RADIUS (Remote Authentication Dial-In User Service) utilizes a
RADIUS server for authentication and the use of dynamic TKIP, AES, or WEP.

IMPORTANT: Always remember that each
device in your wireless network MUST use
the same encryption method and encryption
key or your wireless network will not function
properly.

35

Wireless Security

Security Threats Facing Wireless Networks

Wireless A/G USB Network Adapter

WPA Pre-Shared Key. If you do not have a RADIUS server, select the type of algorithm, TKIP or AES, enter a

password in the Pre-Shared key field of 8-64 characters, and enter a Group Key Renewal period time between
0 and 99,999 seconds, which instructs the Router or other device how often it should change the encryption
keys.

WPA RADIUS. WPA used in coordination with a RADIUS server. (This should only be used when a RADIUS
server is connected to the Router or other device.) First, select the type of WPA algorithm, TKIP or AES. Enter
the RADIUS server’s IP Address and port number , along with a key shar ed between the device and the server.
Last, enter a Group Key Renewal period, which instructs the device how often it should change the encryption
keys.

RADIUS. WEP used in coordination with a RADIUS server. (This should only be used when a RADIUS server is
connected to the Router or other device.) First, enter the RADIUS server’s IP Address and port number, along
with a key shared between the device and the server. Then, select a WEP key and a level of WEP encryption,
and either generate a WEP key through the Passphrase or enter the WEP key manually.

Implementing encryption may have a negative impact on your network’s performance, but if you are transmitting
sensitive data over your network, encryption should be used.

These security recommendations should help keep your mind at ease while you are enjoying the most flexible
and convenient technology Linksys has to offer.

36

Appendix C: Windows Help

Wireless A/G USB Network Adapter

Appendix C: Windows Help

Almost all wireless products require Microsoft Windows. Windows is the most used operating system in the world
and comes with many features that help make networking easier. These features can be accessed through
Windows Help and are described in this appendix.

TCP/IP

Before a computer can communicate with an access point or wireless router, TCP/IP must be enabled. TCP/IP is a
set of instructions, or protocol, all PCs follow to communicate over a network. This is true for wireless networks
as well. Your PCs will not be able to utilize wireless networking without having TCP/IP enabled. Windows Help
provides complete instructions on enabling TCP/IP.

Shared Resources

If you wish to share printers, folder, or files over your network, Windows Help provides complete instructions on
utilizing shared resources.

Network Neighborhood/My Network Places

Other PCs on your network will appear under Network Neighborhood or My Network Places (depending upon the
version of Windows you're running). Windows Help provides complete instructions on adding PCs to your
network.

37

Appendix D: Glossary

Wireless A/G USB Network Adapter

Appendix D: Glossary

802.11a - A wireless networking standard that specifies a maximum data transfer rate of 54Mbps and an

operating frequency of 5GHz.

802.11b - A wireless networking standard that specifies a maximum data transfer rate of 11Mbps and an

operating frequency of 2.4GHz.

802.11g - A wireless networking standard that specifies a maximum data transfer rate of 54Mbps, an operating

frequency of 2.4GHz, and backward compatibility with 802.11b devices.
Access Point - A device that allows wireless-equipped computers and other devices to communicate with a

wired network. Also used to expand the range of a wireless network.

Adapter - A device that adds network functionality to your PC.
Ad-hoc - A group of wireless devices communicating directly with each other (peer-to-peer) without the use of

an access point.

AES (Advanced Encryption Standard) - A method that uses up to 256-bit key encryption to secure data.
Backbone - The part of a network that connects most of the systems and networks together, and handles the

most data.

Bandwidth - The transmission capacity of a given device or network.
Bit - A binary digit.
Byte - A unit of data that is usually eight bits long
CSMA/CA (Carrier Sense Multiple Access/Collision Avoidance) - A method of data transfer that is used to prevent

data collisions.

CTS (Clear To Send) - A signal sent by a wireless device, signifying that it is ready to receive data.
Default Gateway - A device that forwards Internet traffic from your local area network.

38

Appendix D: Glossary

Wireless A/G USB Network Adapter

DHCP (Dynamic Host Configuration Protocol) - A networking protocol that allows administrators to assign

temporary IP addresses to network computers by “leasing” an IP address to a user for a limited amount of time,
instead of assigning permanent IP addresses.

DNS (Domain Name Server) - The IP address of your ISP's server, which translates the names of websites into IP
addresses.

Domain - A specific name for a network of computers.
DSSS (Direct-Sequence Spread-Spectrum) - Frequency transmission with a redundant bit pattern resulting in a

lower probability of information being lost in transit.
EAP (Extensible Authentication Protocol) - A general authentication protocol used to control network access.

Many specific authentication methods work within this framework.
EAP-PEAP (Extensible Authentication Protocol-Protected Extensible Authentication Protocol) - A mutual

authentication method that uses a combination of digital certificates and another system, such as passwords.
EAP-TLS (Extensible Authentication Protocol-Transport Layer Security) - A mutual authentication method that

uses digital certificates.

Encryption - Encoding data transmitted in a network.
Ethernet - IEEE standard network protocol that specifies how data is placed on and retrieved from a common

transmission medium.

Firmware - The programming code that runs a networking device.
Fragmentation -Breaking a packet into smaller units when transmitting over a network medium that cannot

support the original size of the packet.

Gateway - A device that interconnects networks with different, incompatible communications protocols.
Hardware - The physical aspect of computers, telecommunications, and other information technology devices.
Infrastructure - A wireless network that is bridged to a wired network via an access point.
IP (Internet Protocol) - A protocol used to send data over a network.
IP Address - The address used to identify a computer or device on a network.
ISM band - Radio bandwidth utilized in wireless transmissions.

39

Appendix D: Glossary

Wireless A/G USB Network Adapter

ISP (Internet Service Provider) - A company that provides access to the Internet.
LAN - The computers and networking products that make up your local network.
MAC (Media Access Control) Address - The unique address that a manufacturer assigns to each networking

device.

Mbps (MegaBits Per Second) - One million bits per second; a unit of measurement for data transmission.
Network - A series of computers or devices connected for the purpose of data sharing, storage, and/or

transmission between users.

Node - A network junction or connection point, typically a computer or work station.
OFDM (Orthogonal Frequency Division Multiplexing) - Frequency transmission that separates the data stream

into a number of lower-speed data streams, which are then transmitted in parallel to prevent information from
being lost in transit.

Packet - A unit of data sent over a network.
Passphrase - Used much like a password, a passphrase simplifies the WEP encryption process by automatically

generating the WEP encryption keys for Linksys products.

Port - The connection point on a computer or networking device used for plugging in cables or adapters.
RADIUS (Remote Authentication Dial-In User Service) - A protocol that uses an authentication server to control

network access.
Roaming - The ability to take a wireless device from one access point's range to another without losing the

connection.

Router - A networking device that connects multiple networks together.
RTS (Request To Send) - A networking method of coordinating large packets through the RTS Threshold setting.
Server - Any computer whose function in a network is to provide user access to files, printing, communications,

and other services.
Software - Instructions for the computer. A series of instructions that performs a particular task is called a

“program”.
Spread Spectrum - Wideband radio frequency technique used for more reliable and secure data transmission.

40

Appendix D: Glossary

Wireless A/G USB Network Adapter

SSID (Service Set IDentifier) - Your wireless network's name.
Subnet Mask - An address code that determines the size of the network.
Switch - 1. A data switch that connects computing devices to host computers, allowing a large number of

devices to share a limited number of ports. 2. A device for making, breaking, or changing the connections in an
electrical circuit.

TCP (Transmission Control Protocol) - A network protocol for transmitting data that requires acknowledgement
from the recipient of data sent.

TCP/IP (Transmission Control Protocol/Internet Protocol) - A set of instructions PCs use to communicate over a
network.

TKIP (Temporal Key Integrity Protocol) - a wireless encryption protocol that provides dynamic encryption keys for
each packet transmitted.

Topology - The physical layout of a network.
WEP (Wired Equivalent Privacy) - A method of encrypting network data transmitted on a wireless network for

greater security.
WLAN (Wireless Local Area Network) - A group of computers and associated devices that communicate with

each other wirelessly.
WPA (Wi-Fi Protected Access) - a wireless security protocol using TKIP (Temporal Key Integrity Protocol)

encryption, which can be used in conjunction with a RADIUS server.

41

Appendix E: Specifications

Wireless A/G USB Network Adapter

Appendix E: Specifications

Model WUSB54AG
Standards IEEE 802.11a, 802.11b, 802.11g, USB 1.1, USB 2.0
Port USB Port
Cabling Type USB 1.0/1.1/2.0
Channels 802.11b/802.11g

11 Channels (USA, Canada)
13 Channels (Europe)
14 Channels (Japan)

802.11a

8 Channels (USA, Canada)
LEDs Power, Link
Transmit Power 16 dBm
Receive Sensitivity -65 dBm @ 54Mbps, -80 dBm @ 11Mbps
Antenna 2 dBi
Security Features WEP, WPA
WEP Key Bits 64, 128-bit
Dimensions 91 mm x 23 mm x 71 mm (3,58" x 0,91" x 2,80")
Unit Weight 0,08 kg (2,82 oz.)
Certifications FCC, IC-03, Wi-Fi (A and G), CE

42

Appendix E: Specifications

Wireless A/G USB Network Adapter

Operating Temp. 0ºC to 40ºC (32ºF to 104ºF)
Storage Temp. 0ºC to 70ºC (-40ºF to 158ºF)
Operating Humidity 10% to 85%, Non-Condensing
Storage Humidity 5% to 90%, Non-Condensing

43

Appendix F: Warranty Information

Wireless A/G USB Network Adapter

Appendix F: Warranty Information

Linksys warrants to You that, for a period of three years (the “Warranty Period”), your Linksys Product will be substantially
free of defects in materials and workmanship under normal use. Your exclusive remedy and Linksys' entire liability under
this warranty will be for Linksys at its option to repa ir or replace t he Produc t or r efund Your purchase price less any rebates.
This limited warranty extends only to the original purchaser.

If the Product proves defective during the Warranty Period call Linksys Technical Support in order to obtain a Return
Authorization Number, if applicable. BE SURE TO HAVE Y OUR PROOF OF PURCHASE ON HAND WHEN CALLING. If You are
requested to return the Product, mark the Retu rn Authorization Number clearly on the outside of the package and include a
copy of your original proof of purchase. RETURN REQUESTS CANNOT BE PROCESSED WITHOUT PROOF OF PURCHASE. You
are responsible for shipping defective Products to Linksys. Linksys pays for UPS Ground shipping from Linksys back to You
only. Customers located outside of the United States of America and Canada are responsible for all shipping and handling
charges.

ALL IMPLIED WARRANTIES AND CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED
TO THE DURATION OF THE WARRANTY PERIOD. ALL OTHER EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS AND
WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF NON-INFRINGEMENT, ARE DISCLAIMED. Some jurisdictions do not
allow limitations on how long an implied warranty lasts, so the above limitation may not apply to You. This warranty gives
You specific legal rights, and You may also have other rights which vary by jurisdiction.

This warranty does not apply if the Product (a) has been altered, except by Linksys, (b) has not been installed, operated,
repaired, or maintained in accordance with instructions supplied by Linksys, or (c) has been subjected to abnormal physical
or electrical stress, misuse, negligence, or accident. In addition, due to the continual development of new techniques for
intruding upon and attacking networks, Linksys does not warrant that the Product will be free of vulnerability to intrusion or
attack.

TO THE EXTENT NOT PROHIBITED BY LAW, IN NO EVENT WILL LINKSYS BE LIABLE FOR ANY LOST DATA, REVENUE OR PROFIT,
OR FOR SPECIAL, INDIRECT, CONSEQUENTIAL, INCIDENTAL OR PUNITIVE DAMAGES, REGARDLESS OF THE THEORY OF
LIABILITY (INCLUDING NEGLIGENCE), ARISING OUT OF OR RELATED TO THE USE OF OR INABILITY TO USE THE PRODUCT
(INCLUDING ANY SOFTWARE), EVEN IF LINKSYS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT
WILL LINKSYS’ LIABILITY EXCEED THE AMOUNT PAID BY YOU FOR THE PRODUCT. The foregoing limitations will apply even if
any warranty or remedy provided under this Agreement fails of its essential purpose. Some jurisdictions do not allow the
exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to You.

This Warranty is valid and may be processed only in the country of purchase.

Please direct all inquiries to: Linksys, P.O. Box 18558, Irvine, CA 92623.

44

Appendix G: Regulatory Information

Wireless A/G USB Network Adapter

Appendix G: Regulatory Information

FCC STATEMENT
This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15

of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used according to the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which is found by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna
Increase the separation between the equipment or devices
Connect the equipment to an outlet other than the receiver's
Consult a dealer or an experienced radio/TV technician for assistance
FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

INDUSTRY CANADA (CANADA)
This Class B digital apparatus complies with Canadian ICES-003, RSS210.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
The use of this device in a system operating either partially or completely outdoors may require the user to obtain
a license for the system according to the Canadian regulations.

EC DECLARATION OF CONFORMITY (EUROPE)
Refer to the insert for compliance information about Linksys Wireless A+G Products.
Disclaimer: This product is not intended for sale and use in all European countries.

45

Appendix G: Regulatory Information

Wireless A/G USB Network Adapter

SAFETY NOTICES
Caution: To reduce the risk of fire, use only No.26 AWG or larger telecommunication line cord.
Do not use this product near water, for example, in a wet basement or near a swimming pool.
Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning.

46

Appendix H: Contact Information

Wireless A/G USB Network Adapter

Appendix H: Contact Information

Need to contact Linksys?
Visit us online for information on the latest products and updates to your existing products at:
http://www.linksys.com/international

If you experience problems with any Linksys product, you can e-mail us at:

In Europe E-mail Address

Austria [e-mail]
Belgium [e-mail]
Denmark [e-mail]
France [e-mail]
Germany [e-mail]
Italy [e-mail]
Netherlands [e-mail]
Norway [e-mail]
Portugal [e-mail]
Spain [e-mail]
Sweden [e-mail]
Switzerland [e-mail]
United Kingdom & Ireland [e-mail]

Outside of Europe E-mail Address

Latin America [e-mail]
U.S. and Canada [e-mail]