Cisco Explorer 8550HDC, Explorer 854HDC Quick Reference Manual

Check Product Safety

Upon completion of any service or repairs to this product, the service technician must perform safety checks to
determine that this product is in proper operating condition.

Protect the Product when Moving It

Always disconnect the power source when moving the apparatus or connecting or disconnecting cables.

WARNING:

Avoid personal injury and damage to this product! Use only with the cart, stand, tripod,
bracket, or table speciÞ ed by the manufacturer or sold with the apparatus. When a cart is
used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.

20070320 Set-Top Cable US & Canada

IMPORTANT SAFETY INSTRUCTIONS

Read These Instructions
Keep These Instructions
Heed All Warnings
Follow All Instructions

Power Source Warning

A label on this product indicates the correct power source for this product. Operate this product only from an electrical
outlet with the voltage and frequency indicated on the product label. If you are uncertain of the type of power supply to
your home or business, consult your service provider or your local power company.

The AC inlet on the unit must remain accessible and operable at all times.

Ground the Product

WARNING:
Avoid electric shock and Þ re hazard! Do not defeat the safety purpose of the polarized or grounding-type
plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades
and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug
does not Þ t into your outlet, consult an electrician for replacement of the obsolete outlet.

If this product connects to coaxial cable wiring, be sure the cable system is grounded (earthed). Grounding provides
some protection against voltage surges and built-up static charges.

Outdoor Grounding System

If this product connects to an outdoor antenna or cable system, be sure the antenna or cable system is grounded
(earthed). This provides some protection against voltage surges and built-up static charges.

Article 810 of the National Electric Code (NEC) ANSI/NFPA No. 70-1990, provides the following information:

• Grounding of the mast and supporting structure

• Grounding the lead-in wire to an antenna discharge unit

• Size of the grounding conductors

• Location of the antenna-discharge unit

• Connection to grounding electrodes

• Requirements for the grounding electrodes (see the following antenna grounding diagram as recommended by
NEC ANSI/NFPA 70)

WARNING:
Avoid electric shock and Þ re hazard! Do not locate an outside antenna system in the vicinity of overhead
power lines or power circuits. Touching power lines or circuits might be fatal.

Protect the Product from Lightning

For added protection, unplug this apparatus during lightning storms or when unused for long periods of time. In
addition to disconnecting the AC power from the wall outlet, disconnect the signal inputs.

Explorer 8540HDC DVR and 8550HDC DVR
with Multi-Stream CableCARD Interface

Verify the Power Source from the On/Off Power Light

When the on/off power light is not illuminated, the apparatus may still be connected to the power source. The light
goes out when the apparatus is turned off, regardless of whether it is still plugged into an AC power source.

Eliminate AC Mains Overloads

WARNING:
Avoid electric shock and Þ re hazard! Do not overload AC mains, outlets, extension cords, or integral
convenience receptacles. For products that require battery power or other power sources to operate them,
refer to the operating instructions for those products.

Prevent Power Cord Damage

Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point
where the cord exits from the apparatus.

Provide Ventilation and Select a Location

• Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

• Do not place this apparatus on a bed, sofa, rug, or similar surface.

• Do not place this apparatus on an unstable surface.

• Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
ampliÞ ers) that produce heat.

• Do not install this apparatus in an enclosure, such as a bookcase or rack, unless the installation provides proper ventilation.

• Do not place entertainment devices (such as VCRs or DVDs), lamps, books, vases with liquids, or other objects on
top of this product.

Protect from Exposure to Moisture and Foreign Objects

Do not use this apparatus near water.

WARNING:

Avoid electric shock and Þ re hazard! Do not expose this product to liquids, rain, or moisture.

WARNING:
Avoid electric shock and Þ re hazard! Unplug this product before cleaning. Clean only with a dry cloth. Do
not use a liquid cleaner or an aerosol cleaner. Do not use a magnetic/static cleaning device (dust remover)
to clean this product.

WARNING:
Avoid electric shock and Þ re hazard! Never push objects through the openings in this product. Foreign
objects can cause electrical shorts that can result in electric shock or Þ re.

Accessories Warning

WARNING:
Avoid electric shock and Þ re hazard! Only use attachments/accessories speciÞ ed by your service provider
or the manufacturer.

Service Warnings

WARNING:
Avoid electric shock! Do not open the cover of this product. Opening or removing the cover may expose
you to dangerous voltages. If you open the cover, your warranty will be void. This product contains no
user-serviceable parts. Refer all servicing to qualiÞ ed service personnel.

Servicing is required when the apparatus has been damaged in any way, such as a power-supply cord or plug is damaged,
liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.

Notice to Installers

The servicing instructions in this notice are for use by qualiÞ ed service personnel only. To reduce risk of electric shock, do not perform any servicing other than that contained in
the operating instructions, unless you are qualiÞ ed to do so.

20070131 SysInstaller 820 US/Canada/Intl

ScientiÞ c Atlanta, A Cisco Company 770.236.5000
5030 Sugarloaf Parkway, Box 465447,
Lawrenceville, GA 30042 www.scientiÞ catlanta.com

FCC Compliance

United States FCC Compliance

This device has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against such interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in
accordance with the instructions, it may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment OFF and ON, the user is encouraged
to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna, if applicable.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the cable company or an experienced radio/television technician for help.

Any changes or modiÞ cations not expressly approved by ScientiÞ c-Atlanta, Inc., could void the user’s authority to
operate the equipment.

The information shown in the FCC Declaration of Conformity paragraph below is a requirement of the FCC and is intended
to supply you with information regarding the FCC approval of this device. The phone numbers listed are for FCC-related
questions only and not intended for questions regarding the connection or operation for this device. Please contact your
cable service provider for any questions you may have regarding the operation or installation of this device.

Declaration of Conformity

This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: 1) the device
may not cause harmful interference, and 2) the device must accept any interference received, including interference
that may cause undesired operation.

Explorer 8540HDC and 8550HDC Digital Video Recorder

Model: 8540HDC and 8550HDC

Manufactured by: ScientiÞ c-Atlanta, Inc.

5030 Sugarloaf Parkway

Lawrenceville, Georgia 30044 USA

Telephone: [phone]

Canada EMI Regulation

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la class B est conforme à la norme NMB-003 du Canada.

20060628 FCC Standard

Disclaimer

ScientiÞ c-Atlanta, Inc. assumes no responsibility for errors or omissions that may appear in this guide. ScientiÞ c Atlanta
reserves the right to change this guide at any time without notice.

AVC VIDEO LICENSE

With respect to each AVC/MPEG-4/H.264 product, ScientiÞ c Atlanta is obligated to provide the following notice:

THIS PRODUCT IS LICENSED UNDER THE AVC PATENT PORTFOLIO LICENSE FOR THE PERSONAL AND
NON-COMMERCIAL USE OF A CONSUMER TO (i) ENCODE VIDEO IN COMPLIANCE WITH THE AVC STANDARD
(“AVC VIDEO”) AND/OR (ii) DECODE AVC VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A
PERSONAL AND NON-COMMERCIAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED
TO PROVIDE AVC VIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE.

ADDITIONAL INFORMATION MAY BE OBTAINED FROM MPEG LA, L.L.C. SEE HTTP://WWW.MPEGLA.COM.

Accordingly, please be advised that service providers, content providers, and broadcasters are required to obtain a
separate use license from MPEG LA prior to any use of AVC/MPEG-4/H.264 encoders and/or decoders.

ScientiÞ c Atlanta, the ScientiÞ c Atlanta logo, and Explorer are registered trademarks of ScientiÞ c-Atlanta, Inc.

8540HDC and 8550HDC are trademarks of ScientiÞ c-Atlanta, Inc.

Cisco, the Cisco logo, and Cisco Systems are trademarks or registered trademarks of Cisco Systems, Inc. and/or its afÞ liates in the
U.S. and certain other countries.

CableCARD and M-Card are trademarks of Cable Television Laboratories, Inc.
Dolby is a registered trademark of Dolby Laboratories.
Manufactured under license from Dolby Laboratories.
“Dolby” and the double-D symbol are registered trademarks of Dolby Laboratories.
HDMI, the HDMI logo, and High-DeÞ nition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
Macrovision is a registered trademark of Macrovision Corp.

All other trademarks shown are trademarks of their respective owners.

Product and service availability is subject to change without notice.
© 2007 ScientiÞ c-Atlanta, Inc. All rights reserved.

September 2007 Printed in United States of America Part Number 4012390 Rev A

Quick Reference Guide

Note to System Installer

For this apparatus, the coaxial cable shield/screen shall be grounded as close as
practical to the point of entry of the cable into the building.For products sold in the
US and Canada, this reminder is provided to call the system installer's attention to
Article 820-93 and Article 820-100 of the NEC (or Canadian Electrical Code Part 1),
which provides guidelines for proper grounding of the coaxial cable shield.

CAUTION: To reduce the risk of electric shock, do not remov e cover (or b ack).
No user-serviceable parts inside. Refer servicing to qualified service personnel.

WAR NING

This symbol is intended to alert you that uninsulated voltage within this product
may have sufficient magnitude to cause electric shock.Therefore, it is dangerous
to make any kind of contact with any inside part of this product.

Ce symbole a pour but d’alerter toute personne qu’un contact avec une pièce
interne de ce produit, sous tension et non isolée, pourrait être suffisant pour
provoquer un choc électrique. Il est donc dangereux d’être en contact avec toute
pièce interne de ce produit.

TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO
RAIN OR MOISTURE.

This symbol is intended to alert you of the presence of important operating and
maintenance (servicing) instructions in the literature accompanying this product.

Ce symbole a pour but de vous avertir qu’une documentation importante sur le
fonctionnement et l’entretien accompagne ce produit.

CH+

POWER

VOL+VOL-

CH-

SELECT

LISTEXITINFOGUIDE

L AUDIO IN R VIDEO IN

EXPLORER® 8550HDC

™

Connecting to an HDTV with Component Input (YPbPr)

1. Insert the M-Card module if not already installed.

2. Connect the DVR to the coaxial cable coming from the wall.

3. Connect the Y (green) connector on the HDTV to the Y (green) connector on the DVR; connect the Pb (blue) connector on the HDTV to the Pb
(blue) connector on the DVR; and connect the Pr (red) connector on the HDTV to the Pr (red) connector on the DVR.

4. Connect the left audio (white) connector on the HDTV to the left audio (white) connector on the DVR, and connect the right audio (red)
connector on the HDTV to the right audio (red) connector on the DVR.

5. Plug the DVR and the HDTV into an AC power source. Do not press the Power key on the DVR yet.

Important: To potentially protect the DVR from power surge damage, ground (earth) your cable product to provide some protection against

voltage surges and built-up static charges. You may be able to reduce the risk of damage from voltage surges, which can be caused by
lightning storms and power outages, by plugging the DVR into a surge protector.

6. Wait several minutes for the DVR to receive the latest software, programming, and service information. One of the following will appear on
the front panel of the DVR:

• Current time: The update is complete. • Four dashes (----): Call your service provider to get the DVR authorized.

7. To begin watching TV, turn on the HDTV and press Power on the front panel of the DVR, or press Power on the remote control.

U.S. Patents

A patent notice is afÞ xed to this product. In addition, the product may also be covered by one or more of the following patents:

4,498,169, 4,692,919, 4,748,667; 4,829,569; 4,866,770; 4,885,775; 4,888,799; 4,890,319; 4,922,456; 4,922,532; 4,924,498; 4,965,534; 4,991,011; 5,003,384; 5,012,510; 5,029,207;
5,045,816; 5,053,883; 5,054,071; 5,058,160; 5,142,575; 5,142,690; 5,146,526; 5,155,590; 5,214,390; 5,225,902; 5,225,925; 5,235,619; 5,237,610; 5,239,540; 5,241,610; 5,247,364;
5,255,086; 5,257,403; 5,267,071; 5,270,809; 5,271,041; 5,272,752; 5,282,028; 5,285,497; 5,287,351; 5,301,028; 5,309,514; 5,317,391; 5,319,709; 5,341,425; 5,347,388; 5,347,389;
5,357,276; 5,359,601; 5,361,156; 5,367,571; 5,379,141; 5,379,145; 5,381,481; 5,390,337; 5,400,401; 5,406,558; 5,418,782; 5,420,866; 5,420,923; 5,425,101; 5,428,404; 5,430,568;
5,434,610; 5,436,749; 5,438,370; 5,440,632; 5,442,472; 5,455,570; 5,457,701; 5,471,492; 5,477,199; 5,477,262; 5,477,282 5,477,370; 5,481,389; 5,481,542; 5,485,221; 5,493,339;
5,497,187; 5,500,758; 5,502,499; 5,506,904; 5,519,780; 5,539,822; 5,550,825; 5,579,055; 5,579,057; 5,583,562; 5,592,551; 5,596,606; 5,600,378; 5,602,933; 5,640,388; 5,657,414;
5,675,575; 5,684,876; 5,715,515; 5,724,525; 5,734,822; 5,740,300; 5,742,677; 5,754,940; 5,757,416; 5,771,064; 5,774,859; 5,825,829; 5,826,167; 5,850,305; 5,854,703; 5,870,474;
5,892,607; 5,920,626; 5,923,755; 5,930,024; 5,930,515; 5,937,067; 5,963,352; 5,966,163; 5,982,424; 5,991,139; 5,999,207; 6,005,631; 6,005,938; 6,016,163; 6,028,941; 6,029,046;
6,052,384; 6,055,244; 6,072,532; 6,105,134; 6,148,039; 6,157,719; 6,188,729; 6,195,389; 6,212,278; 6,215,530; 6,219,358; 6,240,103; 6,243,145; 6,246,767; 6,252,964; 6,272,226;
6,292,081; 6,292,568; 6,320,131; 6,374,275; 6,405,239; 6,411,602; 6,417,949; 6,424,714; 6,424,717; 6,433,906; 6,438,139; 6,463,586; 6,467,091; 6,476,878; 6,493,876; 6,510,519;
6,516,002; 6,516,412; 6,526,508; 6,538,595; 6,546,013; 6,560,340; 6,567,118; 6,570,888; 6,622,308; 6,629,227; 6,664,984; 6,667,994; 6,671,879; 6,674,967; 6,678,891; 6,714,598;
6,721,352; 6,721,956; 6,725,459; 6,738,982; 6,744,892; 6,744,967; 6,751,271; 6,760,918; 6,795,972; 6,802,077; 6,804,708; 6,811,447; 6,817,028; 6,822,972; 6,823,385; 6,832,386;
6,845,106; 6,868,473; 6,874,075; 6,889,191; 6,909,471; 6,917,622; 6,917,628; 6,922,412; 6,927,806; 6,928,656; 6,931,058; 6,937,729; 6,969,279; 6,971,008; 6,971,121; 6,978,310;
6,986,156; 6,988,900; 6,996,838; 7,010,801; 7,053,960; 7,065,213; 7,069,578; 7,069572; D348065; D354959; D359737; D363932; D390217; D434753; D507240; D507535;
D513407; D516518; RE36368; RE36988

20070417 Patents

1 Power Turns the DVR on and off

2 USB Connects to external USB devices (Reserved for future use)

3 VOL +, VOL - Increases and decreases the volume

4 CH+, CH - Scrolls through the channels

5 Select Accesses your on-screen selection

6 IR Sensor Receives the infrared signal from the remote control

7 LED Display Displays the selected channel number and time of day. The LED also displays the following:

• Message (

)

• HDTV

• Power (

)

• Output Resolution (1080i, 720p, 480p, or 480i)

• AUTO - Automatically outputs native scan rates that your TV can accept

8 Guide Accesses the on-screen guide, video-on-demand, or pay-per-view features

9 Info Displays a description of the selected program. This button is available

from the on-screen guide and while viewing a program

10 Exit Exits menus, the on-screen guide, and program information

11 List Displays the Recorded List

12 Video and Not available on all models. Connects to video and left/right (L/R) audio
Audio Input outputs from a TV or other device. (Not available on 8540HDC)

Welcome

The Explorer® 8540HDC™ and 8550HDC™ DVR Set-Top with a
Multi-Stream CableCARD™ (M-Card™) delivers high-deÞ nition
programming in exceptional picture and audio quality. The M-Card
provides system security and authorization of digital services.
Through these DVR set-tops, you can access interactive services,
such as video-on-demand and pay-per-view programs. Contact your
service provider for information about these and other available
services. Use the instructions in this guide to install the 8540HDC or
8550HDC and to access your program services.

Important! If the M-Card is removed, the set-top will not operate
correctly.

For more information about this product, visit our website:

www.scientiÞ catlanta.com/products/consumers/new_cableboxes.htm

Safety First

Before using this DVR read the IMPORTANT SAFETY
INSTRUCTIONS section of this guide.

Watch TV

Press the following remote control keys to access services and
programs:

• Guide–Display the on-screen program guide

• Arrows–Highlight a program in the schedule

• Info–Display program description

• Select–Watch a speciÞ c program in the guide

Avoid Screen Burn-In!

Images such as letterbox bars or side bars, bright closed-captioning
backgrounds, station logos, or any other stationary images may
cause the HDTV screen to age unevenly and cause damage to your
HDTV. Refer to the user’s guide that came with your HDTV for more
information about screen burn-in.

Automatic Software Updates

A message appears on the TV screen when the DVR and the
M-Card module are receiving software updates. In addition,
download information appears on the front panel of the DVR during
these updates. Wait for the current time to appear on the front panel
before continuing. When the time appears, the update is complete.

Note: If you need further assistance, contact your service provider.

Performance Tips

If the DVR does not perform as expected, the following tips may help.

No picture

• Verify that the M-Card module is installed.

• Verify that the power to your TV is turned on.

• If the DVR is plugged into a wall switch, verify the switch is in the
ON position. (Avoid plugging into an outlet that is controlled by a
wall switch.)

• Verify that all cables are properly connected.

• The current channel may not be available in your service
package.
Try selecting another channel to see if a picture appears.

No color

• Verify that the HDTV is in HD mode. If necessary, re-run the
HDTV Setup Wizard to select HD mode.

• Verify the current TV program is broadcast in color.

• Adjust the TV color controls.

No sound

• If your setup includes a VCR or stereo, verify that you have
properly connected them to the DVR.

• Verify the volume is turned up.

• Verify the mute function is not on.

Explorer 8550HDC Front Panel

Explorer 8550HDC Back Panel

1 Cable In Connects to a coaxial cable that delivers the signal from your service provider
2 Set-Top Bar Code Label Contains set-top serial number and MAC addresses
3 Archive Video Connects to a video input of an archive device
4 L-R Audio Archive Connects to an audio input of an archive device
5 Video 1 (Composite) Connects to a video input of another device, such as a TV or VCR
6 Audio Out (Left/Right) Connects to RCA cables that send analog audio signals (left/right) to a stereo receiver or TV with stereo inputs
7 YPbPr Connects to the component video input (YPbPr) on an HDTV. Do not use these cables if you are using the

HDMI connection
8 Out 2 (Secondary Connects to either a VCR or to another set of inputs (composite) on your TV

Audio Out)

9 Digital Audio Out Connects to an RCA cable that sends a digital audio signal to a surround-sound receiver or other digital audio device
10 S-Video Out Connects to S-Video input of a standard TV or VCR
11 IR Connector reserved for future use
12 Optical Audio Out Connects to an optical cable that sends a digital audio signal to a surround-sound receiver or other digital audio device
13 Cable Out Connects to a coaxial cable that sends analog audio and video signals to a TV or VCR. These signals are

SDTV video and stereo audio

14 HDMI Connects an HDMI™ cable to the HDMI input of an HDTV. HDMI supports both digital audio and video. May be used
to connect to a DVI interface using an HDMI-to-DVI adapter for video and separate audio connections. Any of the
following audio connections may be used: Digital Audio Out (9); Audio Out: Left, Right (6); or Optical Audio Out (12)

15 M-CARD Installed by your service provider
16 USB 2.0 Connects to external USB devices (Reserved for future use)
17 eSATA Connects to an external Serial ATA (eSATA) hard disk drive for expanded drive space. A connected eSATA drive is

not an archival device. Ask your service provider for a list of approved hard drive models for use with the DVR

18 M-CARD Code Label Contains M-CARD serial number and MAC address
19 1394 Connects to display devices equipped with a 1394 input
20 Ethernet Connects to an Ethernet-equipped device (Reserved for future use)
21 AC Outlet Connects to the AC power cord from another device, such as a TV
22 AC Power Input Connects to the power cord to deliver power to the set-top

Safety and Performance Tips

• Keep the top of the DVR free of all objects
and electronic devices, including your TV.

• Always set the DVR on its feet, never on
its side.

WARNING:
Electric shock hazard!
Unplug all electronic
devices before connecting
or disconnecting any device
cables to the DVR.

Connection Example

T13158

POWER

SELECT

VOL+VOL-

CH+

CH-

LISTEXITINFOGUIDE

L AUDIO IN R VIDEO IN

EXPLORER® 8550HDC

™

1 2 8 9 10116543 7 12

THIS DEVICE IS INTENDED TO BE ATTACHED TO A
RECEIVER THAT IS NOT USED TO RECEIVE OVER-THE-AIR
BROADCAST SIGNALS. CONNECTION OF THIS DEVICE
IN ANY OTHER FASHION MAY CAUSE HARMFUL
INTERFERENCE TO RADIO COMMUNICATIONS
AND IS IN VIOLATION OF THE FCC RULES, PART 15.

CABLE OUT

S-VIDEO

OUT

USB 2.0

120VAC

60Hz 80W

120 VAC
60Hz 4.2A

500W

OPTICAL

AUDIO

OUT

MULTI-STREAM CABLE CARD

VIDEO

ARCHIVE OUT 1

L

R

VIDEO

LRPb

Y

Pr

DIGITAL

AUDIO

L

R

IR

1394

AVIS:

RISQUE DE CHOC

ELECTRIQUE NE PAS OUVRIR

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

1394

eSATA

CABLE

IN

SCIENTIFIC-ATLANTA, INC.

CATV CONVERTER
MADE IN MEXICO

LISTED 14H1
VIDEO PRODUCT

eCM MAC: 001AC3F4F7

57

STB

RF

MAC: 001

AC3F$F7

56

STB

SN:

SABPQBQGD

M-CARD SN: PKCPKPDBT

M-CARD MAC: 001AC326910A

T1320 0

19

119

7 864 16

13

1 2 14

15 1810

17 20 22

12

3 215

Note: This illustration
may vary from the
actual product.

Note: This illustration
may vary from the
actual product.

DIGITAL

AUDIO

L

R

OPTICAL

AUDIO

OUT

IR

S-VIDEO

OUT

CABLE OUT

MULTI-STREAM CABLE CARD

M-CARD SN: PKCPKPDBT

M-CARD MAC: 001AC326910A

USB 2.0

AUDIO

CENTER

CHANNEL IN

eSATA

1394

1394

DVI/HDCP

IN

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

AVIS :

RISQUE DE CHOC

ELECTRIQUE NE PAS OUVRIR

LISTED 14H1
VIDEO PRODUCT

Back of
HDTV

120 VAC

60Hz 4.2A

500W

120VAC

60Hz 80W

THIS DEVICE IS INTENDED TO BE ATTACHED TO A
RECEIVER THAT IS NOT USED TO RECEIVE OVER-THE-AIR
BROADCAST SIGNALS. CONNECTION OF THIS DEVICE
IN ANY OTHER FASHION MAY CAUSE HARMFUL
INTERFERENCE TO RADIO COMMUNICATIONS
AND IS IN VIOLATION OF THE FCC RULES, PART 15.

SCIENTIFIC-ATLANTA, INC.

CABLE

IN

Cable

STB SN: SABPQBQGD

eCM MAC: 001AC3F4F757

STB RF MAC: 001AC3F$F756

CATV CONVERTER

MADE IN MEXICO

ARCHIVE OUT 1

VIDEO

L

R

VIDEO

LRPb

Y

Pr

Input

ON OFF

AUDIO IN

S-VIDEO

DVI/HDCP

LR

VIDEO

L/
MONO

R

Y

PB

AUDIOAUDIO

PR

HD 1

IN

IN

VIDEO

L/

L

MONO

R

R

HD 2

Y

PB

AUDIO

PR

INOUT

L

R

ANT (75 )

ANT-1

OUT

ANT-2

T13201