Page 1
CP-8865
Do Not Ship Enclosure with Phone Installed
[PHONE MUST BE INSTALLED ON-SITE]
Page 2
CP-8865 Mounting the Enclosure
Take into consideration before you install:
- Due to the size and mass of this product, it is
important that the Backbox is safely installed
according to these installation instructions.
- Make sure that the type of wall is capable of supporting
the system and use screws that are suitable for that type of wall.
accordance with state and local building regulations.
Page 3
3/16”
Hex L-Key
Jumper Shunt
#6-32 x 3/16”
Button Head Torx
Machine Screw
(Spare)
#8 Hex Nut
(Ground Lug)
Accessory Kits
Drilled Spanner
Driver Bit
Keypad
Coverplate
#6-32 x 5/8” Flat Head
Pin Torx Machine Screw
Machine Screw
(Spare - 2 Pieces)
Torx Security Bit &
Spare Screw Kit
T-15 Pin Torx
Security Driver Bit
Mounting
Screw
Keypad Cover Accessory Kit
#00 Screw Driver Kit
Hookswitch Coverplate
M3x0.5Pitch Machine Screw
+ 1 Spare
T-15 Driver Bit Kit (on the Outside by the Hookswitch)
Phone Mounting Screw Kit
Page 4
Mount the Backbox Assembly
to the Wall
Figure Shown Typical Installation:
Tools Required:
1) Electric Powered Hand Drill
2) Drill Bit (Use Correct Drill Bit for Wood / Concrete)
3) Leveler
4) Torque Wrench, Wrench and Socket
Steps
A) Prepare Hole on Drywall (with Stud Behind) / Concrete
B) Insert Stud Anchors in to Holes
C) Align then Place Backbox Assembly Mounting Holes to Studs Anchors
D) Tighten Washers and Nuts that included with Stud Anchors
E) Torque to Stud Anchors Manufacturer's Recommended ft./lbs.
Page 5
(3)
Remove Both
Remove Handset &
Disconnect Cord from Phone.
Then Connect Power Plug (1) &
Network Cable (2), etc. Through
Mounting Bracket
USB & KEM
Covers
(2)
(1)
Page 6
Right Angle USB-A to
the USB Port on the Side
Phone
Mount
Lower Phone Mount Until Tabs Stops
Then Tightening Screws
This Will Allow Camera to Line Up with
Camera Hole on the Faceplate
Mounting
Holes
AUX
USB-B to
the USB to Analog Audio Module (UAAM)
from Serial
Controller
Network Cable
Tab
Mounting
Cable
Exit
Tab
Cables Run Through Cable Exit then
Connect to Phone
Screw
Screw
Mounting
Update Note: 1) Serial Controller RJ11 to AUX
Date: 02/07/2019
Page 7
Armored Cord Handset to
USB to Analog Audio Module
Tool Provided for Terminal Block Screw:
1) #00 size Phillips Screw Driver
Red Wire to J4 (Position 1)
Yellow Wire to J4 (Position 2)
Green Wire to J4 (Position 3)
Black Wire to J4 (Position 4)
J4
1
2
3
4
5
6
7
8
9
10
Hookswitch Connections
*
Serial Controller Connections (6,7 & 8)
Handset
Connections
RED Wire
YELLOW Wire
GREEN Wire
BLACK Wire
RED Wire
GREEN Wire
RED Wire
*
BLACK Wire
BLACK Wire
USB-B to
5
6
7
8
9
921285C
Armored Cord Handset Wires End
J1
USB-A
To Phone
Install Shunt on JP2
to Enable [Auto Answer Mode]
Page 8
Ground Wire &
Network Cable are
Not Provided
Ground the Backbox from ESD
Hex Nut
Ground Lug
Network Cable
UAAM
*
Serial
Controller
*
Backbox
Assembly
*Handset Wires to
UAAM Not Shown
Page 9
Use Provided Driver Bit
to Install Security Screws
Tool Required:
Powered Screw Driver or Powered Hand Drill
*First Install the Upper Faceplate Assembly
then the Lower Faceplate Assembly
Open Camera Shutter
Before Installing the Faceplate Assembly
<< Factory Disconnected >>
Reconnect Before Installing the Faceplates Assemblies
Also Double Check all Cables and Wires are Plugged in and Secure
UAAM
Connection Label
with Diagram
Page 10
Lip Go Under
Upper Faceplate Assembly
Ground Faceplate from ESD
Diagram Shown Typical Installation
Ground Wires
Twist
Nut
Page 11
2.559 [65.00]
1.628 [41.35]
Dimensions and Features
1.969 [50.00]
3.346 [85.00]
Lanyard Coverplate
Hookswitch Cradle Coverplate
Included for Handsfree Operation
Vandal Resistance Handset with
Stainless Steel Armored Cord
P/N: 611562*
Replace Lanyard Coverplate
with Blank Coverplate
(P/N: 611563* Sold Separate)
for Handsfree Operation
(Optional) SPAR II - RTFM Access Hole
T15 Security Torx Screw Installed from the Inside
(P/N: 031433*)
to Remove Security Drilled Spanner Screw
Use Provided No.6 Drilled Spanner Driver Bit
Replaceable Scratch Resistance
Acrylic Bezel P/N: 621028*
(Included Hex L-Key for Mounting Screws)
Speaker
Hole Cluster
Reserved for Biometric Reader /
RFID Reader Module Upgrade
(Included Two Spare & T15 Torx Driver Bit)
Security Torx Screw
Replaceable Scratch Resistance
Acrylic Bezel for Camera P/N: 621029*
Replaceable Faceplate Assemblies:
Upper Facplate (611584*)
Lower Faceplate (611586*)
Included Keypad Coverplate,
Security Screw & Driver Bit
(for Handsfree Operation)
Microphone
Hole Cluster
4.016 [102.00]
Backbox Assembly
P/N: 611583*
7.559 [192.00]
1.969 [50.00]
3.346 [85.00]
11.417 [290.00]
3.346 [85.00]
1.772 [45.00]
4.724 [120.00]
Ø1.300 [33.00]
Conduit Hole (One on Each Side)
Fits 1" EMT Connector & Conduit
Dimensions are in Inches [Millimeter]
9.449 [240.00]
8.268 [210.00]
Ø0.413 [10.50]
(4 Places)
Ø0.630 [16.00]
(2 Places)
Keyholes & Holes Fits Up to
1/4"- 20 Thread Size
Stud Anchor/Screw/Bolt
4.409 [112.00] 8.976 [228.00]
1.772 [45.00]
Tool Required to Remove Hole Plug:
1) 11/32" or 9mm Socket / Socket Wrench
2.559 [65.00]
1.628 [41.35]
Page 12
*Peel O Protective Film
Before Install on to Backbox
Mounting
Screw
Hex L-Key
Acrylic Bezel
P/N: 621028*
Secure Acrylic Bezel with Tape
* Do Not Block View
Narrow Side
Acrylic Bezel
P/N: 621029*
Mounting
Bracket
Replace the Acrylic Bezels
Loading...