Page 1
CP-8851 / CP-8861
Do Not Ship Enclosure with Phone Installed
[PHONE MUST BE INSTALLED ON-SITE]
Page 2
CP-8851 / 9961 Mounting the Enclosure
Take into consideration before you install:
- Due to the size and mass of this product, it is
important that the Backbox is safely installed
according to these installation instructions.
- Make sure that the type of wall is capable of supporting
the system and use screws that are suitable for that type of wall.
- The system must be installed by qualied personnel, in
accordance with state and local building regulations.
- See sheet ve and ten for Conduit and Wall Mounting instructions.
Page 3
Smaller
Hex L-Key
for Acrylic Bezel
Replacement
#6-32 x 3/16”
Button Head Torx
Machine Screw
(Spare)
Accessory Kits
Drilled Spanner Dirver Bit
Jumper Shunt
#6-32x5/8"Flat Head
Pin Torx Machine Screw
(Spare - 2 Pieces)
#8 Hex Nut
(GND Lug)
Torx Sec. Bit & Spare Screw Kit
#00 Screw Driver Kit
Coverplate
Mounting
Screw
Keypad Cover Accessory Kit
Phone Mounting Screw Kit
T-15 Pin Torx
Security Driver Bit
Page 4
Remove Handset, USB & KEM Covers,
Install all Cables then the Mounting Bracket
Remove Handset &
Disconnect Cord from Phone.
Then Connect Power Plug (1) &
Network Cable (2), etc. before
Install Mounting Bracket
Remove Both
USB & KEM
Covers
Cisco CP-8851 /
Cisco CP-8861
(2)
Mounting
Screw (2 Pieces)
(1)
Mounting
Bracket
Page 5
Plug in the USB Cable
AUX
USB Port
USB-B Plug in to
USB to Analog Audio Module
(See Sheet 6 of 10)
Right Angle
USB-A Plug
AUX
Cable
Page 6
Mount the Backbox Assembly
to the Wall
Figure Shown Typical Installation:
Tools Required:
1) Electric Powered Hand Drill
2) Drill Bit (Use Correct Drill Bit for Wood / Concrete)
3) Leveler
4) Torque Wrench, Wrench and Socket
Step 3
A) Prepare Hole on Drywall (with Stud Behind) / Concrete
B) Insert Stud Anchors in to Holes
C) Align Backbox Assembly Mounting Holes to Studs
D) Tighten Washers and Nuts that included with Stud Anchors
E) Torque to Stud Anchors Manufacturer's Recommended ft./lbs.
Page 7
Hookswitch Cradle
Hookswitch Cradle to Handset Connections
Use Provided #00 Screw Driver
to Install Wires to Terminal Block
USB to Analog
Audio Module
Black Wire to Terminal 4
Armored Cord
Handset Lanyard
Black Wire
Black Wire
Factory Disconnected,
Connect Before Closing the Faceplate
Terminal
Block
Red Wire
to Terminal 5
Black Wire
to Terminal 9
1
10
Green Wire to Terminal 3
Yellow Wire to Terminal 2
Red Wire to Termianl 1
USB-B
Armored Cord
Handset Retainer
Page 8
Install Shunt on JP2
to Enable Auto Answer Mode
Shunt
JP2
Page 9
Phone with
Phone Mount
Intall Phone with Phone Mount
to Backbox
Backbox
Assembly
Page 10
Use Provided Security Torx
Driver Bit to Fasten Screws
to Backbox
Tool Required:
Electric Hand Drill or
Powered Screwdriver
Torx Screw (11x)
Faceplate
Assembly
Backbox
Assembly
Page 11
Security Torx Screw
(Included Two Spare & Torx Driver Bit)
Hookswitch Coverplate
Available for Handsfree
Operation, P/N: 611535A
Dimensions and Features
2.874 [73.0]
Customer Replaceable
Armored Cord Handset with
Steel Lanyard
P/N: 031433D
SPAR II (for Use with
Biometric / RFID)
RTFM Access Hole Covered
by Security Torx Screw
Customer Replaceable
Scratch Resistance Acrylic
P/N: 621028A
Reserved for Biometric Reader /
RFID Reader Module Upgrade
Customer Replaceable
304 Stainless Steel Faceplate
P/N: 611578A
Included Keypad Coverplate,
Screw and Hex L-Key
(for Handsfree Operation)
Coverplate Pre-Installed
To Remove Nut Behind:
Use 1/4” / 6mm Socket
4.724 [120.0]
15.197 [386.0]
4.724 [120.0]
2.087 [53.0]
Ø0.512
[Ø13.0]
(2 Places)
Ø0.315
[Ø8.0]
(6 Places)
Hole Diameter ts 1/4” -20 Thread Size
Stud Anchors/Screw/Bolt
Ø0.827
[Ø21.0]
Fits 1/2" EMT
Connector & Conduit
3.130 [79.5]
12.992 [330.0]
DIMENSIONS ARE IN INCHES [MILLIMETER]
Tool Required to Remove Hole Plug:
1) 11/32" or 9mm Socket & Socket Wrench
1.996 [50.7]
1.526 [38.8]
APPROX. 6.040 [153.4]
4.331 [110.0]
8.661 [220.0]
Loading...