Cisco CP-7914 - 7914 - Key Expansion Module, CP-7914 Quick Start Manual

Quick Start Guide

Cisco IP Phone 7914
Expansion

1 Introduction to the Cisco IP Phone 7914 Expansion

Module

2 Installing the 7914 Expansion Module

3 Features

4 How to Use the 7914 Expansion Module

5 Troubleshooting

6 Technical Specifications

7 For More Information

8 Obtaining Technical Assistance

Module

1 Introduction to the

Cisco

IP Phone 7914 Expansion

Module

The Cisco IP Phone 7914 Expansion Module attaches to your
Cisco
dial numbers to your phone. You can attach one or two
Expansion Modules to your IP
Expansion Modules, you have 28 additional line appearances
and/or speed dial numbers, or a total of 34 line appearances
and/or speed dial numbers.

IP Phone 7960, adding 14 line appearances and/or speed

Phone. When you use two

2 Installing the

7914

You can attach one or two 7914 Expansion Modules to your
IP
your 7914

• Before You Begin

• Installing the 7914 Expansion Module

2

Expansion Module

Phone. Read all of the topics in this section to safely install

Expansion Module.

Before You Begin

Before you begin installing your 7914 Expansion Module, read
all of the following topics in this section:

• Package List

• Footstand Kits

• Additional Equipment

• Safety Notices

Package List

Make sure that you have received all of the following parts in
your package:

• One Cisco IP Phone 7914 Expansion Module

• One RS 232 cable

• One Quick Start Guide

• One Warranty Card

Footstand Kits

In addition to the package list items, you will also need a
Footstand Kit (separate orderable item). If you are attaching
one 7914
Footstand Kit. If you are attaching two
7914
Footstand Kit. The Footstand Kit contains:

• One support bar (single with one thumb screw, or double

• One footstand

Expansion Module, you need to have the single

Expansion Modules, you need to have the double

with two thumb screws)

3

Additional Equipment

You will also need to have the following equipment.

• Small flat head screwdriver—for use during the installation

• Power supply unit—depending on how many

Expansion
Cisco
supply unit(s) as follows:

Modules you are installing and how your

IP Phone 7960 is powered, you will require power

Power over the Ethernet to
your Cisco

Local power to your
Cisco

Note Use of a non-Cisco certified power supply unit may

IP Phone 7960

IP Phone 7960

not work and will void the 7914
product warranty.

With one or two Expansion
Modules, you need a power
supply unit (separate
orderable item).

With one Expansion Module,
no power supply unit needed.

With two Expansion
Modules, you need a power
supply unit (separate
orderable item).

Expansion Module

Safety Notices

These are the safety considerations for using the
7914 Expansion Module. Read these notices before you install
or use the 7914
see the Cisco
Cisco CallManager.

Expansion Module. For translated warnings,

IP Phone Administration Guide for

Warning

4

This warning symbol means danger. You are in a
situation that could cause bodily injury. Before you
work on any equipment, be aware of the hazards
involved with electrical circuitry and be familiar
with standard practices for preventing accidents.

Warning

Warning

Warning

Warning

Read the installation instructions before you
connect the system to its power source.

Ultimate disposal of this product should be
handled according to all national laws and
regulations.

Do not work on the system or connect or
disconnect cables during periods of lightning
activity.

To avoid electric shock, do not connect safety
extra low voltage (SELV) circuits to telephone
network voltage (TNV) circuits. LAN ports contain
SELV circuits, and WAN ports contain TNV
circuits. Some LAN and WAN ports use RJ-45
connectors. Use caution when connecting cables.

The following warnings apply when you use the external power
supply with the 7914

Warning

This product relies on the building's installation

Expansion Module:

for short-circuit (over current) protection. Ensure
that a fuse or circuit breaker no larger than 120
VAC, 15A U.S. (240 VAC, 10A international) is used
on the phase conductors (all current-carrying
conductors).

Warning

The device is designed to work with TN power
systems.

5

Installing the 7914 Expansion Module

Note To ensure a successful installation of the

Expansion Module, make sure you have read the

7914
entire “Before You Begin” section on page 3.

To install the 7914 Expansion Module, you need to perform the
following steps.

1. Remove the Footstand from the Cisco IP Phone 7960

2. Connect the Support Bar to the Cisco IP Phone 7960

3. Connect the 7914 Expansion Module to the Support Bar

4. Connect the RS 232 Cable

5. Connect the Power Supply

6. Connect the Footstand

Refer to the detailed instructions and corresponding
illustrations that follow for each of these high-level steps.

Caution To ensure a successful installation, verify with your

system administrator that your phone is ready for
the 7914
CallManager is installed and configured for the
7914

Administration Guide for Cisco

more information. Make sure that you have all of
the parts that you need (see the
section on page 3).

Expansion Module and that Cisco

Expansion Module. See the Cisco IP Phone

CallManager for

“Before You Begin”

1. Remove the Footstand from the
Cisco

IP Phone 7960

To remove the footstand from the IP Phone 7960 to which you
are attaching the 7914

Step 1 Unplug the Cisco IP Phone 7960 network and power

connections.

6

Expansion Module, follow these steps.

Step 2 Unplug the handset, and headset if one is attached to

the phone.

Step 3 Turn the Cisco IP Phone 7960 over and lay it on a

protected flat surface to prevent it from being
scratched.

Step 4 On the footstand, locate the two foot pins.

Step 5 Using a flat head screwdriver, carefully push away from

your body on one of the foot pins to release it. Then
carefully push away from your body on the other foot
pin to release it.

Note You may have to lift and hold the IP Phone to

support it when pushing the foot pins.

Step 6 Lift off the footstand and store it separately.

63147

7

2. Connect the Support Bar to the
Cisco IP Phone 7960

To connect the support bar to the Cisco IP Phone 7960, follow
these steps.

Step 1 Position the support bar on the back of the IP Phone so

that it fits flush with the phone.

Step 2 Locate the two connector pins.

Step 3 Using a flat head screwdriver, carefully push each of the

connector pins so that the support bar is firmly fastened
to the IP

Phone.

3. Connect the 7914 Expansion Module to the
Support Bar

To connect the Expansion Module to the support bar, follow
these steps.

Step 1 Position the phone so that the front of the phone is

facing up.

Step 2 Line up the two open slots on the bottom of the

Expansion Module with the two hooks on the

7914
support bar. Insert the hooks into the slots and then
rotate the top of the 7914
support bar so that it rests flush with the bar.

Step 3 Tighten the thumb screw on the back of the

Expansion Module.

7914

8

Expansion Module into the

Note If you are installing two Expansion Modules,

repeat Steps 2 and 3 for the second Expansion
Module.

9