Page 1
Models
CHAP T E R
1
Introduction
The 5010/5011 cameras are fixed network dome cameras with a built-in Web-based viewer for live
streaming to a standard Web browser (Microsoft Internet Explorer 8).
The cameras support standard H.264 and MJPEG compression formats and dual video streams that can
be configured for a variety of resolutions, frame rates, and bit rates.
Each camera also includes a 2.8 - 8mm Varifocal Megapixel lens, a ready-to-install indoor enclosure,
and a mechanical IR cut filter for increased low-light sensitivity. Additional lenses are available, and the
cameras accept a wide range of megapixel varifocal CS-mount lenses.
The cameras also include built-in Power over Ethernet (PoE), which supplies power to the camera
through the network. If PoE is not available, the camera is prewired for 24 VAC.
CIVS-IPC-5010 Indoor fixed dome network camera, 2.1 megapixel, day/night, and a
CIVS-IPC-5011 Indoor fixed dome network camera, 2.1 megapixel, day/night, and a
Getting Started
Before installing your network camera, thoroughly familiarize yourself with the information in this
section of the manual.
Note • Do not use a network hub when configuring the network settings for the camera.
• To ensure secure access to the network camera, place the camera behind a firewall when it is
connected to a network.
2.8 ~ 8 mm varifocal megapixel lens. This camera has a clear dome.
2.8 ~ 8 mm varifocal megapixel lens. This camera has a smoked dome.
OL-22669-02
Cisco Video Surveillance 5010/5011 Indoor Fixed HD IP Dome Camera User Guide
1-1
Page 2
Product Overview
Parts List
Remove all of the contents from the shipping box.
Qty Description
1 Back box with camera module
1 Surface mount
1 Lower dome (includes trim ring and bubble)
1 Dome liner
1 4-pin connector
1 2-pin connector
1 Quick Start Guide
Product Overview
Chapter 1 Introduction
Figure 1-1 Camera Connections and Features (Side View)
1 2 3 4
1 Relay and Alarm Connections: One relay that can be used to control an external circuit, and
one alarm for physical input into the system.
2 Accessory Port: For use with compatible accessories.
3 RJ-45 Network Port: Connects the camera to the IP network. Also supplies power to the
camera through the network using PoE. If PoE is not available, the camera is prewired for 24
VA C .
4 24 VAC Power Connections: Supports 24 VAC as the power source if PoE is not used.
278770
1-2
Cisco Video Surveillance 5010/5011 Indoor Fixed HD IP Dome Camera User Guide
OL-22669-02
Page 3
Chapter 1 Introduction
Product Overview
Figure 1-2 Camera Connections and Features (Top View)
1
3 8 9
4 5 6
2 7
278771
1 Reset Button: Reboots the camera or restores the camera’s factory default settings. This
button is recessed. Using a small tool, such as a paper clip, press and release the reset button
once to reboot the camera. Press and hold the reset button for 10 seconds to restore the camera
to the factory default settings.
2 Micro SD Card Slot: Saves a snapshot image to a micro SD card based on alarm activity.
3 Power LED: Glows solid green to indicate that the camera has power and flashes green during
the boot cycle. The LED can be disabled through the user interface. If this LED glows red
(solid or flashing), contact Cisco support for assistance.
4 Lens Mount: Fits a standard CS-mount lens. Use a megapixel lens with the 5010/5011
cameras. A standard definition lens installed on a megapixel camera will limit the resolution
of the camera and create poor image quality.
5 Auto Iris Lens Connector: Controls the auto iris lens. Insert the 4-pin connector from the DC
drive auto iris lens into this connector.
6 NTSC/PAL Button: Toggles the service connector between NTSC and PAL formats. The
default setting is NTSC.
7 Service Port: Outputs analog video. Use this port at the installation site to set up the field of
view and to focus the camera. When a service cable is connected to the camera, video to the
IP stream is disabled.
8 Auto Back Focus Button: Sets the auto back focus mechanism. Press the button once to
center the auto back focus mechanism and to fully open the iris. Press and hold the button for
three seconds to start the auto back focus mechanism and focus the camera.
9 Ethernet Activity/Link LED: Flashes green to indicate that data is being transmitted or
received by the camera. Glows solid amber to indicate that a live network connection is
established and then turns off after one minute of operation.
OL-22669-02
Cisco Video Surveillance 5010/5011 Indoor Fixed HD IP Dome Camera User Guide
1-3
Page 4
Product Overview
Product Label
Chapter 1 Introduction
The product label lists the model number, date code, serial number, and Media Access Control (MAC)
address. This information might be required for setup. The product label is located on the side of the
back box.
1-4
Cisco Video Surveillance 5010/5011 Indoor Fixed HD IP Dome Camera User Guide
OL-22669-02
Loading...