Cisco Catalyst 9400 Series, Catalyst 9407R, Catalyst 9404R, Catalyst 9410R Installation Note
Cisco Catalyst 9400 Series Switching Module Installation Note
Cisco Catalyst 9400 Series Module Installation Note 2
Statement 1071—Warning Definition 2
Cisco Catalyst 9400 Series Module Features 4
Cisco Catalyst 9400 Series Switching Module LEDs 22
Removing and Replacing Switching Modules 22
Related Documentation 28
Notices 30
Revised: July 25, 2019
Cisco Catalyst 9400 Series Module Installation Note
Table 1: Product Numbers:
C9400-LC-48U, C9400-LC-48U= (Spare)C9400-LC-48T, C9400-LC-48T= (Spare)
C9400-LC-24XS, C9400-LC-24XS= (Spare)C9400-LC-48UX, C9400-LC-48UX= (Spare)
C9400-LC-24S, C9400-LC-24S= (Spare)C9400-LC-48S, C9400-LC-48S= (Spare)
C9400-LC-48H, C9400-LC-48H= (Spare)C9400-LC-48P, C9400-LC-48P= (Spare)
This document provides instructions for installing switching modules in Cisco Catalyst 9400 Series Switches.
Statement 1071—Warning Definition
IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you
work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar
with standard practices for preventing accidents. Use the statement number provided at the end of
each warning to locate its translation in the translated safety warnings that accompanied this device.
Statement 1071
Waarschuwing
Varoitus
SAVE THESE INSTRUCTIONS
BELANGRIJKE VEILIGHEIDSINSTRUCTIES
Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan
veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij
elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard praktijken
om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de waarschuwing als
u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt raadplegen.
BEWAAR DEZE INSTRUCTIES
TÄRKEITÄ TURVALLISUUSOHJEITA
Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin
käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu onnettomuuksien
yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen mukana toimitettujen
käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien lausuntonumeroiden
avulla.
SÄILYTÄ NÄMÄ OHJEET
2
Attention
IMPORTANTES INFORMATIONS DE SÉCURITÉ
Ce symbole d'avertissement indique un danger. Vousvous trouvez dans une situation pouvant entraîner
des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez conscient des
dangers liés aux circuits électriques et familiarisez-vous avec les procédures couramment utilisées pour
éviter les accidents. Pour prendre connaissance des traductions des avertissements figurant dans les
consignes de sécurité traduites qui accompagnent cet appareil, référez-vous au numéro de l'instruction
situé à la fin de chaque avertissement.
CONSERVEZ CES INFORMATIONS
Warnung
Avvertenza
Advarsel
WICHTIGE SICHERHEITSHINWEISE
Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen
kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und
den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder
Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten
Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.
BEWAHREN SIE DIESE HINWEISE GUT AUF.
IMPORTANTI ISTRUZIONI SULLA SICUREZZA
Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle persone.
Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli relativi ai
circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti. Utilizzare il numero
di istruzione presente alla fine di ciascuna avvertenza per individuare le traduzioni delle avvertenze
riportate in questo documento.
CONSERVARE QUESTE ISTRUZIONI
VIKTIGE SIKKERHETSINSTRUKSJONER
Dette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade på person. Før du
begynner å arbeide med noe av utstyret, må du være oppmerksom på farene forbundet med elektriske
kretser, og kjenne til standardprosedyrer for å forhindre ulykker. Bruk nummeret i slutten av hver
advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne enheten.
TA VARE PÅ DISSE INSTRUKSJONENE
Aviso
¡Advertencia!
INSTRUÇÕES IMPORTANTES DE SEGURANÇA .
Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de lesões
corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos perigos
envolvidos no manuseio de circuitos elétricos e familiarize-se com as práticas habituais de prevenção
de acidentes. Utilize o número da instrução fornecido ao final de cada aviso para localizar sua tradução
nos avisos de segurança traduzidos que acompanham este dispositivo
GUARDE ESTAS INSTRUÇÕES
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular
cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los procedimientos
estándar de prevención de accidentes. Al final de cada advertencia encontrará el número que le ayudará
a encontrar el texto traducido en el apartado de traducciones que acompaña a este dispositivo.
GUARDE ESTAS INSTRUCCIONES
3
Varning!
VIKTIGA SÄKERHETSANVISNINGAR
Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada.
Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och
känna till vanliga förfaranden för att förebygga olyckor. Använd det nummer som finns i slutet av
varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna
anordning.
SPARA DESSA ANVISNINGAR
Cisco Catalyst 9400 Series Module Features
These tables provide a brief description of each module, the per slot bandwidth, maximum rated power of the modules (where
applicable), minimum and maximum port densities, chassis support information, and restrictions (if any).
4
Gigabit and Multigigabit Ethernet Switching Modules
Cisco Catalyst 9400 Series 48-Port 10/100/1000 Module (C9400-LC-48T)
Description
Minimum / Maximum Port
Density
1
1
The number of ports available on a single switch
48-port, 10/100/1000 BASE-T Gigabit Ethernet switching module.
• Hardware ready for IEEE 1588/802.1as— A Precision Time Protocol (PTP) used for time
synchronization across the network for video and audio applications.
• Supports Energy Efficient Ethernet (EEE)
• Has a built-in, front-facing, passive RFID tag that uses Ultra High Frequency (UHF) RFID
technology and requires an RFID reader with compatible software. It provides
auto-identification capabilities for asset management and tracking. The RFID tags are
compatible with the Generation 2 GS1 EPC Global Standard and are ISO 18000-6C compliant.
They operate in the 860- to 960-MHz UHF band. For more information, see Radio Frequency
Identification (RFID) on Cisco Catalyst 9000 Family Switches.
48 Gbps, full duplex non-blocking trafficPer Slot Bandwidth
• Catalyst 9404R Switch—48 / 96
• Catalyst 9407R Switch—48 / 240
• Catalyst 9410R Switch—48 / 384
Can be installed in any non-supervisor module slot. There are no other restrictions.Support and Restrictions
5
Figure 1: Front View of the C9400-LC-48T Switching Module
Switching module Radio Frequency Identifier (RFID)5STATUS LED1
Captive installation screws6LOCATE (blue beacon) LED2
Ejector levers7PORT LINK LED for the port in the top row3
Model or product number8PORT LINK LED for the port in the bottom row4
6
Cisco Catalyst 9400 Series 48-Port UPOE 10/100/1000 Module (C9400-LC-48U)
Description
48-port, 10/100/1000 BASE-T Gigabit Ethernet module supporting up to 60W Cisco UPOE on
each of its 48 RJ45 ports.
• Hardware ready for IEEE 1588/802.1as— A Precision Time Protocol (PTP) used for time
synchronization across the network for video and audio applications.
• Supports Cisco Phone Discovery and IEEE802.3af and IEEE802.3at.
• Supports Energy Efficient Ethernet (EEE)
• Supports PoE Cable Loss Management
• Saves power with direct power delivery from backplane
• Has a built-in, front-facing, passive RFID tag that uses Ultra High Frequency (UHF) RFID
technology and requires an RFID reader with compatible software. It provides
auto-identification capabilities for asset management and tracking. The RFID tags are
compatible with the Generation 2 GS1 EPC Global Standard and are ISO 18000-6C compliant.
They operate in the 860- to 960-MHz UHF band. For more information, see Radio Frequency
Identification (RFID) on Cisco Catalyst 9000 Family Switches.
• The following switching module features are configured in software. See the software
configuration guide for more information:
• Provides per port power consumption measurement
• Enables you to specify maximum power consumption on every port
• Supports PoE Power Configuration
48 Gbps, full duplex non-blocking trafficPer Slot Bandwidth
Minimum / Maximum Port
Density
2
• Catalyst 9404R Switch—48 / 96
• Catalyst 9407R Switch—48 / 240
• Catalyst 9410R Switch—48 / 384
Support and Restrictions
• Can be installed in any non-supervisor module slot.
• Ensure that the chassis power supply configuration supports the PoE budget adequately. Use
the Cisco Power Calculator for power budgeting estimates and to determine power supply
requirements for a specific PoE configuration.
2
The number of ports available on a single switch
7
Figure 2: Front View of the C9400-LC-48U Switching Module
Switching module Radio Frequency Identifier (RFID)5STATUS LED1
Captive installation screws6LOCATE (blue beacon) LED2
Ejector levers7PORT LINK LED for the port in the top row3
Model or product number8PORT LINK LED for the port in the bottom row4
8
Cisco Catalyst 9400 Series 48-Port UPOE Multigigabit Module (C9400-LC-48UX)
Description
48-port, UPOE Multigigabit Ethernet Module with:
• 24 ports (Ports 1 to 24) 1G POE/POE+/UPOE
• 24 ports (Ports 25 to 48) Multigigabit (mGig) POE/POE+/UPOE
• Hardware ready for IEEE 1588/802.1as— A Precision Time Protocol (PTP) used for time
synchronization across the network for video and audio applications.
• Supports Cisco Phone Discovery and IEEE802.3af and IEEE802.3at.
• Supports Energy Efficient Ethernet (EEE)
• Supports PoE Cable Loss Management
• Saves power with direct power delivery from backplane
• Has a built-in, front-facing, passive RFID tag that uses Ultra High Frequency (UHF) RFID
technology and requires an RFID reader with compatible software. It provides
auto-identification capabilities for asset management and tracking. The RFID tags are
compatible with the Generation 2 GS1 EPC Global Standard and are ISO 18000-6C compliant.
They operate in the 860- to 960-MHz UHF band. For more information, see Radio Frequency
Identification (RFID on Cisco Catalyst 9000 Family Switches).
• The following switching module features are configured in software. See the software
configuration guide for more information:
• Provides per port power consumption measurement
Per Slot Bandwidth
Per slot bandwidth depends on the supervisor module:
80 Gbps with C9400-SUP-1XL ten-slot chassis or C9400-SUP-1.
120 Gbps with C9400-SUP-1XL seven-slot chassis.
Minimum / Maximum Port
Density
3
• Catalyst 9407R Switch—48 / 96
• Catalyst 9407R Switch—48 / 240
• Catalyst 9410R Switch—48 / 384
Support and Restrictions
• Can be installed in any non-supervisor module slot.
• Ensure that the chassis power supply configuration supports the PoE budget adequately. Use
the Cisco Power Calculator for power budgeting estimates and to determine power supply
requirements for a specific PoE configuration.
3
The number of ports available on a single switch
• Enables you to specify maximum power consumption on every port
• Supports PoE Power Configuration with up to 60W power per port on each of its 48
ports.
9
Figure 3: Front View of the C9400-LC-48UX Switching Module
Switching module Radio Frequency Identifier (RFID)5STATUS LED1
Captive installation screws6LOCATE (blue beacon) LED2
Ejector levers7PORT LINK LED for the port in the top row3
Model or product number8PORT LINK LED for the port in the bottom row4
10
Loading...