Cisco Systems 880, HIG880, C892FSPK9, 861WGNPK9RF, 861W User Manual

...

Download

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

Americas Headquarters

Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Tel: 408 526-4000

800 553-NETS (6387)

Fax: 408 527-0883

Text Part Number:

CCSP, the Cisco Square Bridge logo, Follow Me Browsing, and StackWise are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn, and iQuick Study are service marks of Cisco Systems, Inc.; and Access Registrar, Aironet, ASIST, BPX, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, Empowering the Internet Generation, Enterprise/Solver, EtherChannel, EtherFast, EtherSwitch, Fast Step, FormShare, GigaDrive, GigaStack, HomeLink, Internet Quotient, IOS, IP/TV, iQ Expertise, the iQ logo, iQ Net Readiness Scorecard, LightStream, Linksys, MeetingPlace, MGX, the Networkers logo, Networking Academy, Network Registrar, Pac ke t, PIX, Post-Routing, Pre-Routing, ProConnect, RateMUX, ScriptShare, SlideCast, SMARTnet, StrataView Plus, SwitchProbe, TeleRouter, The Fastest Way to Increase Your Internet Quotient, TransPath, and VCO are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries.

All other trademarks mentioned in this document or Website are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0501R)

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.

THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.

The following inform ation is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to correct the interference at their own expense.

The following information is for FCC compliance of Class B devices: The equipment described in this manual generates and may radiate radio-frequency energy. If it is not installed in accordance with Cisco’s installation instructions, it may cause interference with radio and television reception. This equipment has been tested and found to comply with the limits for a Class B digital device in accordance with the specifications in part 15 of the FCC rules. These specifications are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation.

Modifying the equipment without Cisco’s written authorization may result in the equipment no longer complying with FCC requirements for Class A or Class B digital devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television communications at your own expense.

You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures:

• Turn the television or radio antenna until the interference stops.

• Move the equipment to one side or the other of the television or radio.

• Move the equipment farther away from the television or radio.

• Plug the equipment into an outlet that is on a different circuit from the television or radio. (That is, make certain the equipment and the television or radio are on circuits controlled by different circuit breakers or fuses.)

Modifications to this product not authorized by Cisco Systems, Inc. could void the FCC approval and negate your authority to operate the product.

The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California.

NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.

IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

IMPLIED, INCLUDING, WITHOUT

Any Internet Protocol (IP) addresses used in this document are not intended to be actual addresses. Any examples, command display output, and figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses in illustrative content is unintentional and coincidental.

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

Preface

This preface describes the objectives, audience, organization, and conventions of this guide, and describes related documents that have additional information. It contains the following sections:

• Objective, page iii

• Audience, page iii

• Organization, page iv

• Conventions, page iv

• Related Documentation, page xi

Objective

Audience

• Obtaining Documentation and Submitting a Service Request, page xi

This guide provides an overview and explains how to install, connect, and perform initial configuration for the wireless and nonwireless Cisco (ISRs). Some information may not apply to your particular router model.

For warranty, service, and support information, see the “Cisco One-Year Limited Hardware Warranty

Terms” section in the document Readme First for the Cisco 800 Series Integrated Services Routers that was shipped with your router.

This guide is intended for Cisco equipment providers who are technically knowledgeable and familiar with Cisco routers and Cisco

IOS software and features.

860 series and Cisco 880 series integrated services routers

OL-16193-01

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

iii

Organization

This guide is organized into the following chapters and appendix.

Product Overview Describes briefly the router models and the hardware

Installing the Router Lists items shipped with the router, equipment and

Connecting the Router Describes typical connections for the router,

Initial Configuration Provides the procedures for initially configuring the

Appendix A, “Technical Specifications” Provides router, port, and cabling specifications.

Preface

features available.

tools necessary for installing the router, safety warnings and guidelines, and the procedures for installing the router.

procedures for connecting the router to various devices, and how to verify the connections.

router settings.

Conventions

This section describes the conventions used in this guide.

Note Means reader take note. Notes contain helpful suggestions or references to additional information and

material.

Caution This symbol means reader be careful. In this situation, you might do something that could result in

equipment damage or loss of data.

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

OL-16193-01

Preface

Warning

Waarschuwing

Varoitus

IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device.

Statement 1071

SAVE THESE INSTRUCTIONS

BELANGRIJKE VEILIGHEIDSINSTRUCTIES

Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt raadplegen.

BEWAAR DEZE INSTRUCTIES

TÄRKEITÄ TURVALLISUUSOHJEITA

Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien lausuntonumeroiden avulla.

Attention

Warnung

SÄILYTÄ NÄMÄ OHJEET

IMPORTANTES INFORMATIONS DE SÉCURITÉ

Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil, référez-vous au numéro de l'instruction situé à la fin de chaque avertissement.

CONSERVEZ CES INFORMATIONS

WICHTIGE SICHERHEITSHINWEISE

Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.

BEWAHREN SIE DIESE HINWEISE GUT AUF.

OL-16193-01

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

Preface

Avvertenza

Advarsel

Aviso

IMPORTANTI ISTRUZIONI SULLA SICUREZZA

Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti. Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le traduzioni delle avvertenze riportate in questo documento.

CONSERVARE QUESTE ISTRUZIONI

VIKTIGE SIKKERHETSINSTRUKSJONER

Dette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade på person. Før du begynner å arbeide med noe av utstyret, må du være oppmerksom på farene forbundet med elektriske kretser, og kjenne til standardprosedyrer for å forhindre ulykker. Bruk nummeret i slutten av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne enheten.

TA VARE PÅ DISSE INSTRUKSJONENE

INSTRUÇÕES IMPORTANTES DE SEGURANÇA

Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos perigos envolvidos no manuseio de circuitos elétricos e familiarize-se com as práticas habituais de prevenção de acidentes. Utilize o número da instrução fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham este dispositivo.

¡Advertencia!

Varning!

GUARDE ESTAS INSTRUÇÕES

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña a este dispositivo.

GUARDE ESTAS INSTRUCCIONES

VIKTIGA SÄKERHETSANVISNINGAR

Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada. Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och känna till vanliga förfaranden för att förebygga olyckor. Använd det nummer som finns i slutet av varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna anordning.

SPARA DESSA ANVISNINGAR

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

OL-16193-01

Preface

OL-16193-01

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

vii

Preface

Aviso

Advarsel

INSTRUÇÕES IMPORTANTES DE SEGURANÇA

Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham o dispositivo.

GUARDE ESTAS INSTRUÇÕES

VIGTIGE SIKKERHEDSANVISNINGER

Dette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for legemesbeskadigelse. Før du begynder arbejde på udstyr, skal du være opmærksom på de involverede risici, der er ved elektriske kredsløb, og du skal sætte dig ind i standardprocedurer til undgåelse af ulykker. Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de oversatte advarsler, der fulgte med denne enhed.

GEM DISSE ANVISNINGER

viii

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

OL-16193-01

Preface

OL-16193-01

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

Preface

Warning

When installing the product, please use the provided or designated connection cables/power cables/AC adaptors. Using any other cables/adaptors could cause a malfunction or a fire. Electrical Appliance and Material Safety Law prohibits the use of UL-certified cables (that have the “UL” shown on the code) for any other electrical devices than products designated by CISCO. The use of cables that are certified by Electrical Appliance and Material Safety Law (that have “PSE” shown on the code) is not limited to CISCO-designated products. Statement 371.

There is the danger of explosion if the battery is replaced incorrectly. Replace the battery only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions.

Statement 1015

Do not use this product near water; for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool.

Statement 1035

Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.

Statement 1036

Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.

Statement 1037

Warning

Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning.

Statement 1038

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

OL-16193-01

Preface

Product Overview

This chapter provides an overview of the features available for the Cisco 860 series and Cisco 880 series integrated services routers (ISRs), and contains the following sections:

• General Description, page 1-1

• Cisco 860 Series ISRs, page 1-2

• Cisco 880 Series ISRs, page 1-3

• Hardware Features, page 1-8

Note For compliance and safety information, see the Regulatory Compliance and Safety Information

Roadmap that ships with the router and the

Series and SOHO Series Routers.

Regulatory Compliance and Safety Information for Cisco 800

Note The illustrations in this document show a wireless router. Both wireless and nonwireless models are

available in the Cisco both wireless and nonwireless routers.

General Description

The Cisco 860 series and Cisco 880 series ISRs provide data, voice, wireless, integrated Virtual Private Network (VPN), and backup capability to corporate teleworkers and to remote and small offices with fewer than twenty users. These routers are capable of bridging and multiprotocol routing between LAN and WAN ports, and provide advanced features such as (global industry standard) symmetrical high-speed DSL (G.SHDSL), 802.11n, quality of service (QoS), firewall, antivirus protection, and Secure Socket Layer (SSL).

The Cisco 860 series and Cisco 880 series ISRs have a desktop form factor with built-in wall-mount features. These ISRs are powered by an external power supply adapter. The various models differ in the WAN interface and features that they support.

860 series and Cisco 880 series ISRs. Port and feature locations are similar for

OL-16193-01

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

1-1

Cisco 860 Series ISRs

231969

Cisco 860 Series ISRs

The Cisco 860 series ISRs are fixed-configuration data routers that support the following features:

• An integrated 4-port 10/100 Ethernet switch for connecting to the LAN

• A10/100 Fast Ethernet (FE) port for connecting to the WAN

• Optional, embedded-wireless access point

Figure 1-1 shows the front panel details of the Cisco 860 wireless router.

Figure 1-1 Front Panel of the Cisco 860 Series Wireless ISR

Chapter 1 Product Overview

1 LEDs

1-2

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

OL-16193-01

Chapter 1 Product Overview

232181

31 4 6 7 852

WAN

FE 4

Cisco 861W

Figure 1-2 shows the back panel details of the Cisco 861 wireless (861W) ISR. Nonwireless routers do

not have antennas or connectors on the back panel. However, the feature locations are similar for all Cisco

Figure 1-2 Back Panel of the Cisco 861-W ISR

Cisco 880 Series ISRs

860 series routers.

1 Primary WAN port—10/100 FE 5 Reset button 2 Antenna—captive omnidirectional dipole

WLAN antenna (wireless models only)

3 4-port 10/100 Ethernet switch 7 Earth ground connector 4 Serial port—console or auxiliary 8 Kensington security slot

Cisco 880 Series ISRs

The Cisco 880 series ISRs have data and voice capabilities. They have the following features:

• Integrated 4-port 10/100 Ethernet switch for connecting to the LAN

• 10/100 FE, or a G.SHDSL port for connecting to the WAN

• Optional, 802.11n embedded-wireless access point

• Optional, Power over Ethernet (PoE)

• DIMM expansion socket that can accept up to 512 MB of additional memory, for a total of 768 MB

The following features are located on the front panel:

• USB 1.1 port

• Express card slot for third-generation (3G) cellular data WAN connectivity, available only on the

Cisco 88xG models

6 Power connector

OL-16193-01

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

1-3

Cisco 880 Series ISRs

231950

1 2 3

Cisco 880 Series Data Routers

The Cisco 880 series data routers provide integrated VPN, wireless, 3G, and backup capabilities.

Figure 1-3 and Figure 1-4 show the features available on Cisco 880 series data routers. Some of the

features shown may not be available on your router.

Figure 1-3 shows the front panel details of the Cisco 880 wireless data router. The USB port and the 3G

card slot are located on the front panel.

Figure 1-3 Front Panel of the Cisco 880 Series Wireless Data Router

Chapter 1 Product Overview

1 LED 3 USB port 2 3G express card slot—Supports third-party1

3G card (Cisco 88xG models only)

1. See the Cisco 880 series ISRs data sheet for supported vendors.

1-4

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

OL-16193-01

Chapter 1 Product Overview

231951

1 4 5 6 8 9 1072 3

Figure 1-4 shows the back panel details of the Cisco 888W data router. Nonwireless routers do not have

antennas or connectors on the back panel. However, the feature locations are similar across all Cisco 880 series data routers.

Figure 1-4 Back Panel of the Cisco 888-W Data Router

Cisco 880 Series ISRs

1 ISDN port—not available on 3G models 6 PoE power connector 2 Primary WAN port—G.SHDSL or 10/100 FE 3 Antenna—captive omnidirectional dipole

WLAN antenna (wireless models only)

4 4-port 10/100 Ethernet switch 9 Earth ground connector 5 Serial port—console or auxiliary 10 Kensington security slot

1. The 10/100 FE WAN port is located at the bottom left corner. See Figure 1-2.

Cisco 880 Series Voice Routers

The Cisco 880 series voice routers provide managed voice services that interface with Foreign Exchange Station (FXS), Foreign Exchange Office (FXO), or Basic Rate Interface (BRI) connections.

Figure 1-6, and Figure 1-7, show the features available on the Cisco 880 series voice routers. The

features available vary depending on the router model. Some features may not be available on your router.

7 Reset button 8 Power connector

Figure 1-5,

OL-16193-01

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

1-5

Cisco 880 Series ISRs

270495

1 2

Chapter 1 Product Overview

Figure 1-5 shows the front panel details of the Cisco 880 wireless voice router.

Figure 1-5 Front Panel of the Cisco 880 Series Wireless Voice Router

1 LEDs 2 USB port

1-6

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

OL-16193-01

Chapter 1 Product Overview

241904

31 4 7 98 1022 56

Figure 1-6 shows the back panel details of the Cisco 880SRST-W voice router.

Figure 1-6 Back Panel of the Cisco C881SRST-W Voice Router

Cisco 880 Series ISRs

1 Primary WAN port—10/100 FE 6 Antenna—captive wireless omnidirectional

dipole WLAN antenna (wireless models only)

2 Voice ports—four FXS1/DID2 ports, one

7 Reset button

FXO3 port with TBP4 power failover

3 4-port 10/100 Ethernet switch 8 Power connector 4 Serial port—console or auxiliary 9 Earth ground connector 5 PoE power connector 10 Kensington security slot

1. FXS = Foreign Exchange Station.

2. DID = Direct Inward Dialing.

3. FXO = Foreign Exchange Office.

4. TBP = trunk bypass.

OL-16193-01

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

1-7

Hardware Features

241905

32 2 4 7 9 1086 51

Chapter 1 Product Overview

Figure 1-7 shows the back panel details of the Cisco 888SRST-W voice router.

Figure 1-7 Back Panel of the Cisco C888SRST-W Voice Router

1 Primary WAN port—G.SHDSL 6 Antenna—captive wireless omnidirectional

2 Voice ports—four FXS1/DID2 ports, and one

voice BRI3 port

3 4-port 10/100 Ethernet switch 8 Power connector 4 Serial port—console or auxiliary 9 Earth ground connector 5 PoE power connector 10 Kensington security slot

1. FXS = Foreign Exchange Station.

2. DID = Direct Inward Dialing.

3. BRI = Basic Rate Interface.

Hardware Features

This section provides an overview of the following hardware features for the Cisco 860 series and Cisco

880 series ISRs. A feature summary is available at the end of this section.

• Kensington Lock

• Reset Button

• LEDs

• Memory

dipole WLAN antenna (wireless models only)

7 Reset button

1-8

• USB Port

• Fan

• Power over Ethernet Module

• 3G Cellular Data WAN Connectivity

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

OL-16193-01

Chapter 1 Product Overview

• Wireless LAN Connectivity

• Feature Summary

Kensington Lock

A Kensington security slot is located on the router back panel. To secure the router to a desktop or other surface, use the Kensington lockdown equipment.

Reset Button

The Reset button resets the router configuration to the default configuration set by the factory. To reset the hardware and its embedded wireless access point, simultaneously press the reset button while applying power to the router.

Note When you reset the hardware when the embedded wireless access point is running Cisco Unified IOS

software, the router will shutdown but the access point will continue running. Clients with Cisco by the controller.

Hardware Features

Unified IOS software are controlled by a Wireless LAN Controller (WLC) and can only be reset

LEDs

The LEDs are located on the front panel of the router. Tabl e 1-1 describes the LEDs for the Cisco 860 series and the Cisco 880 series ISRs.

Table 1-1 LED Descriptions for the Cisco 860 Series and Cisco 880 Series ISRs

LED Color Description 860 Series 880 Series

Power OK Green On—DC power is being supplied to the router and the

Cisco

IOS software is running.

Blinking—Bootup is in process, or the router is in ROMMON monitor mode.

Off—Power is not supplied to the router.

Link Status FE10 Green On—Ethernet port is connected.

Link Status FE1

Link Status FE2

Link Status FE3

FE WAN Port Link Status

Green On—Port is connected.

Blinking—Data is either being received or being transmitted.

Off—Ethernet port is not connected.

Blinking—Data is either being received or being transmitted.

Off—Port is not connected.

All models All models

861 models 881 models

OL-16193-01

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

1-9

Chapter 1 Product Overview

Hardware Features

Table 1-1 LED Descriptions for the Cisco 860 Series and Cisco 880 Series ISRs (continued)

LED Color Description 860 Series 880 Series

WLAN (2.4 GHz) Green On—Radio is connected, SSID2 is configured, signal is being

transmitted, and client is associated, but no data is being received or being transmitted.

Slow blinking—Radio is connected, SSID is configured, and beacons are being transmitted.

Fast blinking—Data is either being received or being transmitted.

Off—Radio is shut down, and no SSID is configured.

WLAN LINK (Autonomous Mode)

Green On—Wireless link is up.

Blinking—Ethernet link is up and data is either being received or being transmitted.

Off—Wireless link is down.

WLAN LINK (Unified Mode)

Green On—Ethernet link is up, wireless access point is

communicating with LWAPP controller.

Wireless models

— Wireless

models

Blinking—Ethernet link is up, wireless access point is not communicating with LWAPP controller.

Off—Ethernet link is down.

PoE

Green On—PoE is connected and powered.

Off—PoE is not installed.

— Models with

PoE

Amber On—Fault with the PoE.

VPN

PPP

xDSL6 CD Green On—The xDSL interface is connected to the DSLAM7.

Green On—VPN is connected. — All models

Green On—At least one PPP session is established. — All models

— 888 models

Blink—Training to the line.

Off—Indicates that a connection has not been established or the port is shut down.

xDSL Data Green Blink—The xDSL interface is either receiving or transmitting

— 888 models

data.

Off—No data is being transmitted or being received.

Data BRI8 LINK Green On—ISDN D channel is connected. — 888 models

Data BRI B1 Green Blinking—B1 channel is either receiving or sending data, or

— 888 models

data is passing through ISDN channel 1.

Data BRI B2 Green Blinking—B2 channel is receiving or sending data, or data is

— 888 models

passing through ISDN channel 2.

3G9 WWAN

Green On—Service is established.

— 3G models

1-10

Slow Blinking—Searching for service.

Fast Blinking—Data is either being received or being transmitted.

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

OL-16193-01

Chapter 1 Product Overview

Hardware Features

Table 1-1 LED Descriptions for the Cisco 860 Series and Cisco 880 Series ISRs (continued)

LED Color Description 860 Series 880 Series

3G RSSI

3G GSM

3G CDMA

FXO14 Vo i c e Green On—FXO port is connected.

BRI Voice LNK Green On—BRI interface is connected. — SRST

BRI Voice B1 Green On—BRI B1 channel is connected.

BRI Voice B2 Green On—BRI B2 channel is connected.

FXS16/DID17 Vo i c e Green On—FXS/DID port is connected.

1. FE = Fast Ethernet.

2. SSID = Service Set Identifier.

3. PoE = Power over Ethernet.

4. VPN = Virtual Private Network.

5. PPP = Point-to-Point Protocol.

6. xDSL = General term referring to various forms of DSL, including ADSL (asymmetric digital subscriber line) and G.SHDSL.

7. DSLAM = digital subscriber line access multiplexer.

8. BRI = Basic Rate Interface.

9. 3G = Third-Generation.

10. WWAN = wireless WAN.

11. RSSI = Received Signal Strength Indicator.

12. GSM = Global System for Mobile Communication.

13. CDMA = code division multiple access.

14. FXO = Foreign Exchange Office.

15. SRST = Survivable Remote Site Telephony.

16. FXS = Foreign Exchange Station.

17. DID = Direct Inward Dialing.

Green Off—Low signal strength (lower than -100 dBm).

— 3G models

On—High RSSI (-69 dBm or higher).

Slow Blinking—Low or medium RSSI (-99 to -90 dBm).

Fast Blinking—Medium RSSI (-89 to -70 dBm).

Amber On—No service. — 3G models

Green On—Service is established.

— 3G models

Off—No service.

Green On—Service is established.

— 3G models

Off—No service.

— 881-SRST

Blinking—FXO port is either receiving or transmitting data.

models

— SRST

Blinking—BRI B1 channel is either receiving or transmitting

models

data.

— SRST

Blinking—BRI B2 channel is receiving or transmitting data.

models

— SRST

Blinking—FXS/DID port is either receiving or transmitting

models

data.

OL-16193-01

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

1-11

Hardware Features

Memory

Chapter 1 Product Overview

The Cisco 860 series and Cisco 880 series routers contain flash memory and main memory.

Flash Memory

The Cisco 860 series and Cisco 880 series ISRs use non-upgradable flash memory storage. Onboard flash memory contains the Cisco quack contains the cookie configuration.

The default flash memory for the Cisco 860 series and Cisco 880 series ISRs is 128 MB. The default flash memory for the Cisco

Note Flash memory is not upgradable. An external USB flash may be used if additional flash memory is

needed.

Main Memory

The Cisco 860 series and Cisco 880 series routers contain 256 MB of onboard CPU memory. The Cisco

880 series routers contain a SODIMM expansion slot that accommodates a single PC2-4200,

256

MB or 512 MB double data rate 2 (DDR2) small-outline DIMM (SODIMM), for a maximum of 768

MB.

IOS software image, boot flash contains the ROMMON boot code, and

880 series voice routers is 256 MB.

USB Port

A Universal Serial Bus (USB 1.1-compliant) port is located on the front panel. The USB port provides connection for USB devices such as security tokens and flash memory.

Fan

Some router models do not have a fan, while others have either one or two fans.

The fans spin at full speed, as a diagnostic aid, immediately after the router is powered up. After the router has booted, the fans will spin continuously at a speed determined by a variable-speed controller. The fans spin only as fast as necessary to minimize fan noise while maintaining a safe internal operating temperature.

Power over Ethernet Module

The 2-port Power over Ethernet (PoE) module provides power to 802.3af compliant devices connected to FE port 0 and FE port 1.

The 2-port PoE module is an option available only for the Cisco 880 series ISRs, and requires a 48 V external power adapter.

1-12

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

OL-16193-01

Chapter 1 Product Overview

3G Cellular Data WAN Connectivity

The 3G (Evolution Data Only [EVDO], Universal Mobile Telecommunications Systems [UMTS]) cellular interface is intended for use as a backup data link, but it can also be used as a primary WAN data link. The 3G technology is third-generation wide-area cellular technology that is used in voice telephony and broadband wireless data in a mobile environment.

The Cisco 88xG models come with a 34-mm express card slot ready for use with a commercial 3G card radio. The 3G express card slot is located on the front panel. For a list of supported 3G cards see the Cisco 880 series ISRs

data sheet.

Wireless LAN Connectivity

The embedded wireless access point is preinstalled in the router as an optional feature. The wireless access point provides 802.11n wireless connectivity. The Cisco 860 series routers support autonomous features and network configurations. The Cisco 880 series routers support both autonomous and unified features and network configurations.

The wireless access point does not have an external console port for connections. To configure the wireless device, you must use a console cable to connect a PC to the host router’s console port as described in CLI to access the interface.

Table 1-2 describes the radios and antenna for the Cisco 860 series and Cisco 880 series routers.

Chapter 3, “Connecting a Terminal or PC to the Console Port,” and then use the Cisco IOS

Hardware Features

Table 1-2 Wireless Device Radios and Antennas

Radio Module Platform Radio Band

Single-band 802.11n draft 2.0 radio module

1. Actual data rate is highly dependent on your wireless environment.

Cisco 860 & 880 series routers

2.4 GHz Up to 100 Mbps Cisco 860 series:

Maximum Data Throughput

Mode Antenna

Three captive 2-dBi

autonomous only

Cisco 880 series: autonomous and unified

omnidirectional dipole antennas

Feature Summary

Table 1-3 summarizes the hardware features available in the Cisco 860 series and Cisco 880 series ISRs.

Table 1-3 Hardware Features Available in Cisco 860 Series and Cisco 880 Series ISRs

Feature Description 860 Series 880 Series

Reset button Resets the router configuration to the factory default. All models All models

FE1 built-in switch ports

Provides connection to 10/100BASE-T (10/100-Mbps) Fast

Ethernet networks. The autosensing function in these routers eliminates the need for a crossover cable and allows the router to detect MDI2 or MDIX3 in any other PC or hub with a straight-through cable or a crossover cable.

All models All models

OL-16193-01

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

1-13

Chapter 1 Product Overview

Hardware Features

Table 1-3 Hardware Features Available in Cisco 860 Series and Cisco 880 Series ISRs (continued)

Feature Description 860 Series 880 Series

Console or AUX port

Security features Provides support for VPNs4, Cisco IOS Firewall, and IPsec5.

Embedded wireless access point

FE WAN port Provides connection to 10/100BASE-T. Can be connected to

Battery backed-up Real-time clock (RTC)

USB port Supports high-speed USB 1.1. Provides connection for USB

PoE

G.SHDSL8 port Provides 2-wire or 4-wire connection to a G.SHDSL

3G9 card slot Provides backup data link. — 3G models

Dying gasp Detects when the router is about to lose power, and sends a

Data BRI port Provides backup and remote management functions by

FXO12 port An FXO interface connects local calls to a central office or

Provides a connection to the terminal or PC for software configuration or troubleshooting. The console port may be configured as a virtual auxiliary port for dial backup and remote management.

Additionally, the Cisco 880 series routers also provide URL filtering.

Provides 802.11n connectivity. The radio is backward compatible with 802.11b/g.

other network devices, such as a cable modem, an xDSL6 modem, or router. The router is capable of bridging and multiprotocol routing between the LAN and WAN ports.

Provides nonvolatile date and time when the router is powered on. The RTC is used for verifying the validity of the Certification Authority stored on the router.

devices such as security tokens and flash memory.

(Optional) Provides power for devices (such as phones) that are connected to the router.

network.

power-fail signal to warn the DSLAM10 about the impending line drop.

connecting to the ISDN service provider if the main G.SHDSL link fails.

PBX. This is the interface a standard telephone provides.

All models All models

Wireless models Wireless models

861 models 881 models

— All models

— Models with PoE

— 888 models

— xDSL models

— xDSL models,

except for the 3G and SRST11 models

— 881 SRST models

1-14

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

OL-16193-01

Chapter 1 Product Overview

Hardware Features

Table 1-3 Hardware Features Available in Cisco 860 Series and Cisco 880 Series ISRs (continued)

Feature Description 860 Series 880 Series

FXS13/DID14 port

BRI voice port The ISDN BRI S/T voice interface provides a client-side

1. FE = Fast Ethernet.

2. MDI = media-dependent interface in normal mode.

3. MDIX = media-dependent interface in crossover mode.

4. VPN = Virtual Private Network.

5. IPsec = IP security.

6. xDSL = General term referring to various forms of DSL, including ADSL (asymmetric digital subscriber line) and G.SHDSL.

7. PoE = Power over Ethernet.

8. G.SHDSL = (global industry standard) symmetrical high-speed DSL.

9. 3G = Third-Generation.

10. DSLAM = digital subscriber line access multiplexer.

11. SRST = Survivable Remote Site Telephony.

12. FXO = Foreign Exchange Office.

13. FXS = Foreign Exchange Station.

14. DID = Direct Inward Dialing.

An FXS interface connects directly to a standard telephone, a fax machine, or similar device. This interface supplies ringing voltage and dial tone to the station.

(TE) ISDN S/T physical interface for connection to an NT1 device that terminates an ISDN telephone network.

— SRST models

OL-16193-01

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

1-15

Hardware Features

Chapter 1 Product Overview

1-16

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

OL-16193-01

Installing the Router

This chapter describes the equipment and the procedures for successfully installing the Cisco 860 series and Cisco

• Equipment, Tools, and Connections, page 2-1

• Installing the Router, page 2-3

Note For compliance and safety information, see the Regulatory Compliance and Safety Information

Roadmap that ships with the router and the

Series and SOHO Series Routers.

Equipment, Tools, and Connections

This section describes the equipment, tools, and connections necessary for installing your Cisco 860 series and Cisco

880 series integrated services routers (ISRs), and contains the following sections:

Regulatory Compliance and Safety Information for Cisco 800

880 series ISRs.

CHA PTER

Items Shipped with your Router

Unpack the box and verify that all items listed on the invoice have been shipped with the router.

Table 2-1 lists the items and their quantities that are shipped with each router model.

Ta b l e 2-1 Items and Their Quantities That Are Shipped with the Cisco 860 Series And Cisco 880

Series ISRs

Item

RJ-45–to–RJ-45 Ethernet cable

DSL2 cable

RJ-45–to–DB-9 console cable 1 1

External 60-W power supply adapter 1 1

OL-16193-01

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

Cisco 860 Series Routers

1 1

Cisco 880 Series Routers

2-1

Equipment, Tools, and Connections

Table 2-1 Items and Their Quantities That Are Shipped with the Cisco 860 Series And Cisco 880

Chapter 2 Installing the Router

Series ISRs (continued)

Item

Power supply cable 1 1

Cisco Configuration Professional (CCP) CD41 1

1. Cisco 861 and Cisco 881 ISRs only.

2. DSL = digital subscriber line.

3. Cisco 888 ISRs only.

4. Some SKUs do not include CCP.

Additional Items

The following items are not shipped with the router, but are required for installation:

• ESD-preventive cord and wrist strap.

• Screws for mounting the router on a wall:

• Wire crimper for chassis grounding.

• Wire for connecting the chassis to an earth ground:

Cisco 860 Series Routers

–

Two number-10 wood screws (round- or pan-head) with number-10 washers, or two number-10

Cisco 880 Series Routers

washer-head screws, for mounting on a wall stud. The screws must be long enough to penetrate at least 3/4 in. (20 mm) into the supporting wood or metal wall stud.

–

Two number-10 wall anchors with washers, for mounting the router on a hollow-wall.

• A ring terminal with an inner diameter of 1/4 in. (5 to 7 mm), for NEC-compliant chassis grounding.

• Ethernet cables for connecting to the Fast Ethernet (FE) WAN and LAN ports.

Connections

Obtain a broadband or Ethernet connection from your service provider.

Ethernet Devices

Identify the Ethernet devices that you will connect to the router: hub, servers, and workstations or PCs. Ensure that each device has a network interface card (NIC) for connecting to Ethernet ports.

• If you plan to configure the software using Cisco IOS commands through the console port, provide

• If you plan to connect a modem, provide the modem and modem cable.

• If you plan to use the Data BRI port, provide an NT1 device and an ISDN S/T cable.

• If you plan to use the cable-lock feature, provide a Kensington or equivalent locking cable.

–

AWG 14 (2 mm2) or larger wire for NEC-compliant chassis grounding.

–

AWG 18 (1 mm2) or larger wire for EN/IEC 60950–compliant chassis grounding.

an ASCII terminal or a PC that is running terminal emulation software to connect to the console port.

2-2

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

OL-16193-01

Chapter 2 Installing the Router

Installing the Router

This section describes how to install the Cisco 860 series and Cisco 880 series ISRs. These routers can either be installed on a table top or other flat horizontal surface or be mounted on a wall.

Installing the Router

Warning

Caution Do not cover or obstruct the router vents located on both sides of the router; otherwise, overheating could

Caution Do not place anything on top of the router that weighs more than 10 pounds (4.5 kilograms), and do not

This equipment needs to be grounded. Use a green and yellow 12 to 14 AWG ground wire to connect the host to earth ground during normal use.

This unit is intended to be mounted on a wall. Please read the wall mounting instructions carefully before beginning installation. Failure to use the correct hardware or to follow the correct procedures could result in a hazardous situation to people and damage to the system.

This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available.

occur and cause damage to the router.

stack routers on a desktop. Excessive weight on top of the router could damage the chassis.

Statement 242

Statement 248

Statement 1024

Caution Do not install the router or power supplies next to a heat source of any kind, including heating vents.

Installing on a Table

To install the router on a table or other flat horizontal surface, firmly place the router on a table, or other horizontal surface. Keep at least 1 in. (2.5 cm) of clear space beside the cooling inlet and exhaust vents.

Connect the chassis to a reliable earth ground. For the chassis ground connection procedures, see the

“Installing the Router Ground Connection” section on page 2-6.

Mounting on a Wall

The Cisco 860 series and Cisco 880 series ISRs have mounting holes on the bottom of the chassis for mounting the unit on a wall or other vertical surface.

Note The mounting holes are bidirectional. You can hang the router with the LEDs either facing you or facing

away from you.

OL-16193-01

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

2-3

Installing the Router

3.673 in.8.200 in.

5.961 in.

Tip When choosing a location for wall-mounting the router, consider cable limitations and wall structure.

Step 1 Anchor the screws into the wall, leaving 1/8 in. (0.32 cm) between the screw head and the wall.

Chapter 2 Installing the Router

To mount the router on the wall, follow these steps:

Figure 2-1 shows the wall-mount holes located on the underside of the router.

Figure 2-1 Wall-mount Holes on the Underside of the Router

1 Wall-mount holes

Step 2 Hang the router on the screws, and place the power adapter on a nearby horizontal surface. See

Figure 2-2.

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

2-4

OL-16193-01

Chapter 2 Installing the Router

231982

Figure 2-2 Router Mounted on the Wall

Installing the Router

1 Two number-10 wood screws mounted on the

wall

3 Horizontal surface on which to place the

power adapter

2 Wall-mount holes 4 Distance between the screw head and the wall,

1/8 in. (0.32 cm)

Step 3 Connect the chassis to a reliable earth ground. For the chassis ground connection procedures, see the

“Installing the Router Ground Connection” section on page 2-6.

OL-16193-01

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

2-5

Installing the Router

Installing the Router Ground Connection

The router must be connected to a reliable earth ground. Install the ground wire in accordance with local electrical safety standards.

• For NEC-compliant grounding, use size 14 AWG (2 mm

with an inner diameter of 1/4 in. (5 to 7 mm).

• For EN/IEC 60950–compliant grounding, use size 18 AWG (1 mm

To install the ground connection, follow these steps:

Step 1 Strip one end of the ground wire to the length required for the ground lug or terminal. Step 2 Crimp the ground wire to the ground lug or ring terminal, using the wire crimper. Step 3 Attach the ground lug or ring terminal to the chassis as shown in Figure 2-3. For a ground lug, use the

provided two screws with captive locking washers. For a ring terminal, use one of the screws provided. Tighten the screws to a torque of 8 to 10 in-lb (0.9 to 1.1 N-m).

Figure 2-3 Chassis Ground Connection Using Ring Terminal

Chapter 2 Installing the Router

) or larger copper wire and a ring terminal

) or larger copper wire.

2-6

231981

1 Ring Terminal

Step 4 Connect the other end of the ground wire to a known reliable earth ground point at your site.

After you install and properly ground the router, you can connect the power wiring, the WAN and LAN cables, and the cables for administrative access as required for your installation.

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

OL-16193-01

CHA PTER

Connecting the Router

This chapter describes how to connect Cisco 860 series and Cisco 880 series integrated services routers (ISRs) to Ethernet devices, Power over Ethernet (PoE), and the network. The chapter contains the following sections:

• Preparing to Connect the Router, page 3-2

• Connecting a PC, Server, or Workstation, page 3-3

• Connecting a Phone, page 3-4

• Connecting an External Ethernet Switch, page 3-5

• Connecting a Terminal or PC to the Console Port, page 3-6

• Connecting a Data BRI Port, page 3-7

• Connecting an FE Line—FE4 WAN Port, page 3-9

• Connecting a G.SHDSL Line—G.SHDSL Port, page 3-10

• Connecting Power over Ethernet, page 3-11

• Connecting the AC Adapter, page 3-11

• Connecting an FXS line, page 3-14

• Connecting a FXO Line, page 3-16

• Connecting a Voice ISDN BRI Line, page 3-17

• Verifying Connections, page 3-19

Note For compliance and safety information, see the Regulatory Compliance and Safety Information

Roadmap that ships with the router and the

Series and SOHO Series Routers.

Note The illustrations in this chapter show a wireless router with antennas attached. Nonwireless routers do

not have antennas or antenna connectors on the back panel. However, the procedures for connecting devices to the router are the same for both wireless and nonwireless routers.

Note Depending on the features available for your router, some content in this chapter may not apply to your

router.

Regulatory Compliance and Safety Information for Cisco 800

OL-16193-01

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

3-1

Preparing to Connect the Router

Before you connect the router to the devices, install the router according to the instructions in Chapter 2,

“Installing the Router.”

Preventing Damage to the Router

To prevent damage to your router, follow these guidelines when connecting devices to your router:

• Turn off power to the devices and to the router until all connections are completed.

Caution Do not turn on the devices until after you have completed all connections to the router.

• Connect the color-coded cables supplied by Cisco Systems to the color-coded ports on the back

panel.

• If you must supply your own cable, see Appendix A, “Technical Specifications,” for cabling

specifications. If this appendix does not provide specifications for a particular cable, we strongly recommend ordering the cable from Cisco

Chapter 3 Connecting the Router

Systems.

3-2

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

OL-16193-01

Chapter 3 Connecting the Router

231989

Connecting a PC, Server, or Workstation

To connect a PC (or other Ethernet devices) to an Ethernet switch port, follow these steps:

Step 1 Connect one end of the yellow Ethernet cable to a Ethernet switch port on the router. Figure 3-1 shows

a Cisco 888W router connected to a PC.

Figure 3-1 Connecting a Server, PC, or Workstation

Connecting a PC, Server, or Workstation

OL-16193-01

1 Yellow Ethernet cable 3 RJ-45 port on the network interface card

(NIC)

2 Ethernet switch port on the router

Step 2 Connect the other end of the cable to the RJ-45 port on the network interface card (NIC) installed in the

PC, server, or workstation.

Step 3 (Optional) Connect additional servers, PCs, or workstations to the other Ethernet switch ports.

Note Use the Cisco Configuration Express to configure the Internet connection settings. See the

Cisco Configuration Professional Quick Start Guide for more information.

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

3-3

Connecting a Phone

270551

ABC3DEF

JKLGHI6MNO

TUVPQRS9WXYZ

OPER

Connecting a Phone

To connect a phone to an Ethernet switch port, follow these steps:

Step 1 Connect one end of the yellow Ethernet cable to Ethernet switch port 0 or port 1 on the router. Figure 3-2

shows a Cisco 888W router connected to a phone.

Figure 3-2 Connecting a Phone

Chapter 3 Connecting the Router

3-4

1 Yellow Ethernet cable 3 RJ-45 port on a phone 2 Ethernet switch port 1 on the router

Step 2 Connect the other end of the cable to the RJ-45 port on the phone.

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

OL-16193-01

Chapter 3 Connecting the Router

MODE

Catalyst 3500

SERIES

INLINE POWER

SYSTEM

15X

16X

RPS

STA

TUS UTIL

DUPLX

SPEED

15X

16X

1 2

231986

Connecting an External Ethernet Switch

If more than four PCs in an office must be connected to each other, you can add Ethernet connections to the router by connecting an external Ethernet switch to the router’s Ethernet switch.

To connect an external Ethernet switch to an Ethernet switch port on the router, perform the following steps:

Step 1 Connect one end of the yellow Ethernet cable to an Ethernet switch port on the router.

Figure 3-3 shows a Cisco 888W router connected to an Ethernet switch.

Figure 3-3 Connecting to an Ethernet Switch

Connecting an External Ethernet Switch

1 Ethernet switch port on the router 2 Available port on the external Ethernet switch 3 Yellow Ethernet cable, RJ-45–to–CAT-5,

connecting to an external Ethernet switch port.

Step 2 Connect the other end of the cable to the available port on the Ethernet switch to add additional Ethernet

connections.

Step 3 Turn on the Ethernet switch.

OL-16193-01

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

3-5

Connecting a Terminal or PC to the Console Port

231990

FE0

FE1

FE2

FE3

Connecting a Terminal or PC to the Console Port

Connect a terminal or PC to the Console Aux port either to configure the software by using the command-line interface (CLI) or to troubleshoot problems with the router.

To connect a terminal or PC to the console port on the router and access the CLI, follow these steps:

Step 1 Connect the RJ-45 end of a DB-9–to–RJ-45 serial cable to the RJ-45 Console Aux port on the router.

Figure 3-4 shows the RJ-45 end of the serial cable connected to the Console Aux port on the router.

Figure 3-4 Connecting a Terminal or PC to the Console Port

Chapter 3 Connecting the Router

1 RJ-45 connector to the Console Aux port on

the router

Step 2 Connect the DB-9 end of the DB-9–to–RJ-45 serial cable to the to the COM port on your laptop or PC.

Note Some laptops and personal computers do not come with DB-9 serial port connectors and may

use a USB-to-serial port adapter.

Step 3 To communicate with the router, start a terminal emulator application.

Terminal Emulator Settings

Use the following settings for the terminal emulator connection:

• 9600 baud

• 8 data bits, no parity

• 1 stop bit

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

3-6

2 DB-9 connector

OL-16193-01

Chapter 3 Connecting the Router

• no flow control

When the terminal emulator establishes communications, the router prompt is displayed.

For more information on terminal emulation settings, see Applying Correct Terminal Emulator Settings

for Console Connections.

Connecting a Data BRI Port

You can connect the Data BRI port to the ISDN service provider as a backup link to the WAN port in case the primary xDSL (general term referring to various forms of DSL, including [global industry standard] symmetrical high-speed DSL [G.SHDSL]) WAN service fails. The Data BRI connection is not available on the third-generation (3G) models.

The cabling requirements for the ISDN S/T connection are as follows:

• You must provide two unshielded Category 5 cables. The first cable connects the NT1 box to the

splitter, and the second cable connects the splitter to the wall jack.

• There are RJ-45 connectors at both ends of the default orange ISDN S/T cable. However, an

RJ-45–to–RJ-11 ISDN S/T cable is available upon request if the wall jack at the site requires an RJ-11 connector. Contact your router reseller for the appropriate cable.

Connecting a Data BRI Port

Caution Both LAN and WAN ports use RJ-45 connectors. Use caution when connecting cables to these

connectors. To avoid damage to the router, do not connect telephone-network voltage (TNV) circuits (such as ISDN or DSL circuits) to safety extra-low voltage (SELV) circuits (such as LAN circuits).

OL-16193-01

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

3-7

Connecting a Data BRI Port

Although the following procedure shows a Cisco 888W data router, this procedure applies to all Cisco

To connect the Data BRI port to the ISDN service provider, follow these steps:

Step 1 Connect one end of the orange ISDN S/T cable to the Data BRI port on the router. Figure 3-5 shows a

Data BRI connection.

Figure 3-5 Connecting the Data BRI Port to the ISDN Line

Chapter 3 Connecting the Router

880 series router with a Data BRI port.

231991

1 End of the ISDN S/T cable, which connects to

the Data BRI port on the router

5 xDSL splitter (provided by the xDSL service

provider)

2 Network termination 1 (NT1) box 6 Other end of the first unshielded Category 5

cable, which connects to the telephone line port on the splitter

3 Other end of the ISDN S/T cable, which

connects to the S/T port on the NT1 box

7 One end of the second unshielded Category 5

cable, which connects to the telecommunication service port on the splitter

4 One end of the first unshielded Category 5

cable, which connects to the U port on the

NT1 box

8 Other end of the second unshielded

Connecting Power over Ethernet

Figure 3-8 shows how to connect the 48-VDC Power over Ethernet (PoE) power adapter in your

Cisco 880 series ISR to an AC power outlet. The PoE provides power to port 0 and port 1 of the 4-port 10/100 FastEthernet switch.

Note The router should also be connected to an AC power outlet through a 12-V adapter. To connect the router

to an AC outlet, see “Connecting the AC Adapter” section on page 3-11.

Figure 3-8 Connecting PoE

Connecting Power over Ethernet

1 PoE input jack 4 AC plug 2 Power cord 5 DC plug 3 Power adapter—48 VDC 6 Power adapter—60 W, 12 VDC

Connecting the AC Adapter

Warning

OL-16193-01

The device is designed to work with TN power systems.

This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that a fuse or circuit breaker no larger than 120VAC, 20A U.S. (240VAC, 16 to 20A international) is used on the phase conductors (all current-carrying conductors). The fuse or circuit breaker must have adequate safety approvals recognized by the country of usage.

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

Statement 19

Statement 119

3-11

Connecting the AC Adapter

231996

To connect your Cisco 860 series or Cisco 880 series ISR to an AC power outlet, follow these steps:

Step 1 Connect the router to an AC power outlet as shown in Figure 3-9.

Figure 3-9 Connecting the AC Adapter

Chapter 3 Connecting the Router

1 DC plug 3 Power adapter—60 W, 12 VDC 2 Power cord 4 AC plug

3-12

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

OL-16193-01

Chapter 3 Connecting the Router

Step 2 To secure the power cord to the router, attach the power lock clip to the power cord, slide the clip to the

end of the DC plug. See

Figure 3-10 Securing the Power Cord

Connecting the AC Adapter

Figure 3-10.

270659

1 Power lock clip 2 Power cord 3 DC plug 4 Holes on either side of the power connector

OL-16193-01

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

3-13

Connecting an FXS line

270800

Step 3 Snap the latches into the holes on either side of the power connector. See Figure 3-11.

Chapter 3 Connecting the Router

Figure 3-11 Power Lock Clip Latched Into the Holes on Either Side of the Power Connector

1 Power lock clip 2 Power cord 3 Power adapter 4 AC plug

Connecting an FXS line

Use a standard straight-through RJ-11 modular telephone cable to connect an Foreign Exchange Service (FXS) port to a telephone or fax machine.

Warning

This equipment contains a ring signal generator (ringer), which is a source of hazardous voltage. Do not touch the RJ-11 (phone) port wires (conductors), the conductors of a cable connected to the RJ-11 port, or the associated circuit-board when the ringer is active. The ringer is activated by an incoming call.

For connections outside the building where the equipment is installed, the following ports must be connected through an approved network termination unit with integral circuit protection: FXS.

3-14

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

OL-16193-01

Chapter 3 Connecting the Router

To connect the FXS line, follow these steps:

Step 1 Connect one end of the straight-through RJ-11 cable to the FXS port. Figure 3-12 shows an FXS line

connection.

Figure 3-12 Connecting an FXS Line

Connecting an FXS line

Fax machine or telephone

1 FXS port 3 RJ-11 port 2 RJ-11 cable

Step 2 Connect the other end of the cable to the RJ-11 port on the telephone or fax machine.

241907

OL-16193-01

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

3-15

Connecting a FXO Line

Use a straight-through RJ-11 cable to connect the Foreign Exchange Office (FXO) voice port to the PSTN or PBX through a telephone wall outlet.

To connect the FXO line, follow these steps:

Step 1 Connect one end of the straight-through RJ-11 cable to the FXO port. See Figure 3-13.

Figure 3-13 Connecting an FXO line

Chapter 3 Connecting the Router

1 FXO port 3 Telephone outlet 2 RJ-11 cable

Step 2 Connect the other end of the cable to an RJ-11 telephone wall outlet.

270542

3-16

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

OL-16193-01

Chapter 3 Connecting the Router

Connecting a Voice ISDN BRI Line

Use a straight-through RJ-45 cable to connect the Voice Basic Rate Interface (BRI) port to the ISDN network through a telephone wall outlet or other device.

Caution To prevent damage to the router, be sure to connect the BRI cable to the BRI connector only, and not to

any other RJ-45 connector.

To connect the Voice BRI line, follow these steps:

Step 1 Connect one end of a straight-through RJ-45–to–RJ-45 cable to the Voice BRI port.

Note When the interface is configured as NT and is connecting to a TE device, use a crossover cable.

See Tabl e A-7.

Connecting a Voice ISDN BRI Line

OL-16193-01

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

3-17

Connecting a Voice ISDN BRI Line

241906

Figure 3-14 shows a Voice BRI line connection.

Figure 3-14 Connecting a Voice BRI Line

Chapter 3 Connecting the Router

3-18

1 Voice BRI port 3 Wall jack 2 RJ-45 cable

Step 2 Connect the other end of the cable to the RJ-45 wall outlet or other device.

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

OL-16193-01

Chapter 3 Connecting the Router

Verifying Connections

To verify that all devices are properly connected to the router, first turn on all the connected devices. Then check the LEDs. To verify router operation, refer to

For full LED description see Ta bl e 1-1 LED Descriptions for the Cisco 860 Series and Cisco 880 Series

ISRs.

Ta b l e 3-1 Verifying the Router Operation

Power and Link LEDs to Check Normal Patterns

Power OK On when power is supplied to router.

To servers, PCs, workstations, or an

LAN 0, LAN 1, LAN 2, or LAN 3 On when the FE LAN port is physically connected to a

server, PC, workstation, or external Ethernet switch. external Ethernet switch connected to the LAN ports (FE10, FE1, FE2, or FE3)

To FE WAN line WAN FE4 On when the WAN Ethernet carrier has detected status.

Blinks when receiving or transmitting data.

To xDSL2 line xDSL CD Green when the line is connected to the xDSL DSLAM3.

xDSL Data Green when receiving or sending data.

To ISDN l i ne Data BRI LNK Green when the ISDN line is connected.

Data BRI B1 and B2 Green when the channel is connected.

WWAN

Green when service is established.

Table 3-1 .

Slow blinking when searching for service.

RSSI

Amber when service is not established.

Green when signal strength is high.

Off or slow blinking when signal strength is low.

Fast blinking when signal strength is medium.

CDMA

GSM

Green when service is established.

To PPP9 clients PPP Green when either a PPPoE10 or PPPoA11 client is running.

To VPN12 tunnel VPN Green when a crypto session is running.

To wireless LAN WLAN LINK Wireless LAN link status:

• Green if at least one client is associated.

• Off if no client is associated.

WLAN 2.4 GHz Wireless LAN 2.4-GHz status:

• Green when radio is connected, SSID

is configured,

signal is being transmitted, and client is associated.

• Slow blinking when radio is connected, SSID is

configured, and signal is being transmitted.

OL-16193-01

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

3-19

Chapter 3 Connecting the Router

Verifying Connections

Table 3-1 Verifying the Router Operation (continued)

Power and Link LEDs to Check Normal Patterns

PoE

1. FE = Fast Ethernet.

2. xDSL = General term referring to various forms of DSL, including ADSL (asymmetric digital subscriber line) and G.SHDSL.

3. DSLAM = digital subscriber line access multiplexer.

4. 3G = Third-Generation.

5. WWAN = wireless WAN.

6. RSSI = Received Signal Strength Indicator.

7. CDMA = code division multiple access.

8. GSM = Global System for Mobile Communication.

9. PPP = Point-to-Point Protocol.

10. PPPoE = PPP over Ethernet.

11. PPPoA = PPP over ATM.

12. VPN = Virtual Private Network.

13. SSID = Service Set Identifier.

14. PoE = Power over Ethernet.

PoE 0 Green when connected and powered.

PoE 1 Amber when there is a fault with the inline power supply.

3-20

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

OL-16193-01

CHA PTER

Initial Configuration

This chapter provides instructions for initial configuration of the Cisco 860 series and Cisco 880 series Integrated Services Routers (ISRs). For initial configuration, we recommend using Cisco

Configuration Professional (CP) Express. Cisco CP Express is a web-based graphical user

interface that guides you through initial configuration.

You may also initially configure your router by using the Cisco IOS command-line interface (CLI) or by using the setup command facility. To create the initial configuration, the setup command facility prompts you for basic information about your router and network.

This chapter contains the following sections:

• Cisco Configuration Professional Express, page 4-1

• Cisco IOS CLI, page 4-1

• Setup Command Facility, page 4-3

• Verifying the Initial Configuration, page 4-5

• Initial Configuration of the Wireless Access Point, page 4-5

Note Some SKUs may not include a default configuration file. If your router does not have a default

configuration file, go to the settings.

“Setup Command Facility” section on page 3 to configure the initial router

Cisco Configuration Professional Express

After you connect cables and power up the router, we recommend that you use the Cisco CP Express web-based application to configure the initial router settings.

For instructions on how to use Cisco CP Express to configure the router see the Cisco CP Express User’s

Guide.

Cisco IOS CLI

To configure the initial router settings by using the Cisco IOS CLI, you will need to set up a console connection. For instructions on how to setup a console connection, see the

PC to the Console Port” section on page 3-6.

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

OL-16193-01

“Connecting a Terminal or

4-1

Cisco IOS CLI

Step 1 Set up a console connection to your router. The following message is displayed:

Step 2 Press Return or Enter. The following message is displayed:

Chapter 4 Initial Configuration

To configure the initial router settings using Cisco IOS CLI, follow these steps:

... router con0 is now available

Cisco Configuration Professional Express (Cisco CP Express) is installed on this device. This feature requires the one-time use of the username "cisco" with the password "cisco." The default username and password have a privilege level of 15.

Please change these publicly known initial credentials using Cisco CP Express or the Cisco IOS CLI.

Here are the Cisco IOS commands.

username <myuser> privilege 15 secret 0 <mypassword> no username cisco

Replace <myuser> and <mypassword> with the username and password you want to use.

For more information about Cisco CP please follow the instructions in the QUICK START GUIDE for your router... ... User Access Verification Username:

Step 3 Enter the username cisco and press Return or Enter. The following prompt is displayed:

Password:

Step 4 Enter the password cisco and press Return or Enter. The following prompt is displayed:

Router#

A message is displayed that is similar to the first warning message. The message directs you to change the username and password.

You are now in privileged EXEC mode.

Note You must change the username and password before you log off the router. You cannot use the

username cisco or password cisco after you log off from this session.

Step 5 To change the username and password, enter the following at the prompt:

username username privilege 15 secret 0 password

Username and password are the username and password that you wish to use.

To continue using Cisco IOS CLI for initial configuration, see the applicable configuration procedures in the

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Software Configuration Guide.

4-2

Note Save your configuration changes regularly to avoid losing them during resets, power cycles, or

power outages. Use the copy

running-config startup-config command at the privileged EXEC

mode prompt (Router#) to save the configuration to NVRAM.

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

OL-16193-01

Chapter 4 Initial Configuration

Step 6 Verify the initial configuration. See the “Verifying the Initial Configuration” section on page 4-5.

Setup Command Facility

The setup command facility guides you through the configuration process by prompting you for the specific information that is needed to configure your system. Use the setup command facility to configure a hostname for the router, to set passwords, and to configure an interface for communication with the management network.

To use the setup command facility, you will need to set up a console connection with the router and enter the privileged EXEC mode.

Note For instructions on how to set up a console connection see the “Connecting a Terminal or PC to

the Console Port” section on page 3-6.

To configure the initial router settings with setup command facility, follow these steps:

Setup Command Facility

Step 1 Set up a console connection to your router and enter privileged EXEC mode. For instructions on how to

enter privileged EXEC mode see

Step 1 through Step 4 in the “Cisco IOS CLI” section on page 4-1

section.

Step 2 In privileged EXEC mode, at the prompt, enter setup.

yourname# setup

The following message is displayed:

--- System Configuration Dialog ---

Continue with configuration dialog? [yes/no]:

You are now in setup command facility.

The prompts in the setup command facility vary, depending on your router model, on the installed interface modules, and on the software image. The following steps and the user entries (in bold) are shown as examples only.

Note If you make a mistake while using the setup command facility, you can exit and run the setup

command facility again. Press Ctrl-C, and enter the setup command at the privileged EXEC mode prompt (Router#). For more information on using the setup command facility, see

The

Setup Command chapter in Cisco IOS Configuration Fundamentals Command Reference, Release 12.2T.

Step 3 To proceed using the setup command facility, enter yes:

Continue with configuration dialog? [yes/no]: yes

OL-16193-01

Step 4 When the following messages appear, enter yes to enter basic management setup:

At any point you may enter a question mark '?' for help. Use ctrl-c to abort configuration dialog at any prompt.

Default settings are in square brackets '[]'.

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

4-3

Setup Command Facility

Step 5 Enter a hostname for the router (this example uses Router):

Step 6 Enter an enable secret password. This password is encrypted (more secure) and cannot be seen when

Step 7 Enter an enable password that is different from the enable secret password. This password is not

Chapter 4 Initial Configuration

Basic management setup configures only enough connectivity for management of the system, extended setup will ask you to configure each interface on the system

Would you like to enter basic management setup? [yes/no]: yes

Configuring global parameters: Enter host name [Router]: Router

viewing the configuration.

The enable secret is a password used to protect access to privileged EXEC and configuration modes. This password, after entered, becomes encrypted in the configuration. Enter enable secret: xxxxxx

encrypted (less secure) and can be seen when viewing the configuration.

The enable password is used when you do not specify an enable secret password, with some older software versions, and some boot images. Enter enable password: xxxxxx

Step 8 Enter the virtual terminal password, which prevents unauthenticated access to the router through ports

other than the console port:

The virtual terminal password is used to protect access to the router over a network interface. Enter virtual terminal password: xxxxxx

Step 9 Respond to the following prompts as appropriate for your network:

Configure SNMP Network Management? [yes]: Community string [public]:

A summary of the available interfaces is displayed.

Step 10 Choose one of the available interfaces for connecting the router to the management network:

Enter interface name used to connect to the management network from the above interface summary: fastethernet4

Step 11 Respond to the following prompts as appropriate for your network:

Configuring interface FastEthernet0: Use the 100 Base-TX (RJ-45) connector? [yes]: yes Operate in full-duplex mode? [no]: yes Configure IP on this interface? [yes]: yes IP address for this interface: 172.1.2.3 Subnet mask for this interface [255.255.0.0] : 255.255.0.0 Class B network is 172.1.0.0, 26 subnet bits; mask is /16

The configuration is displayed:

The following configuration command script was created:

4-4

hostname Router enable secret 5 $1$D5P6$PYx41/lQIASK.HcSbfO5q1 enable password xxxxxx line vty 0 4 password xxxxxx

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

OL-16193-01

Chapter 4 Initial Configuration

snmp-server community public ! no ip routing ! interface FastEthernet0 no shutdown speed 100 duplex auto ip address 172.1.2.3 255.255.0.0 !

Step 12 Respond to the following prompts. Enter 2 to save the initial configuration.

[0] Go to the IOS command prompt without saving this config. [1] Return back to the setup without saving this config. [2] Save this configuration to nvram and exit.

Enter your selection [2]: 2 Building configuration... Use the enabled mode 'configure' command to modify this configuration.

Press RETURN to get started! RETURN

The user prompt is displayed. Router>

Verifying the Initial Configuration

Step 13 Verify the initial configuration. See the “Verifying the Initial Configuration” section on page 4-5 for

verification procedures.

After the initial configuration file is created, you can use the Cisco IOS CLI to perform additional configuration.

Verifying the Initial Configuration

To verify that the new interfaces are operating correctly, perform the following tests:

• To verify that the interfaces and line protocol are in the correct state—up or down—enter the show

interfaces command.

• To display a summary status of the interfaces configured for IP, enter the show ip interface brief

command.

• To verify that you configured the correct hostname and password, enter the show configuration

command.

After you complete and verify the initial configuration, you can configure your Cisco router for specific functions.

Initial Configuration of the Wireless Access Point

The embedded wireless access point (AP) runs its own IOS. You can initially configure the embedded wireless AP using one of the following methods:

• Cisco Configuration Professional (CP) Express

• Setup command facility on the embedded wireless device

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

OL-16193-01

4-5

Initial Configuration of the Wireless Access Point

For information on how to do basic wireless configuration on your router see the Basic Wireless Device chapter of the Cisco 860 Series and Cisco 880 Series Integrated Services Routers Software

Configuration Guide.

Chapter 4 Initial Configuration

4-6

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

OL-16193-01

APPENDIX

Technical Specifications

This appendix provides router, port, and cabling specifications for Cisco 860 series and Cisco 880 series Integrated Services Routers (ISRs). It contains the following sections:

• Router Specifications, page A-1

• Wireless Access Point, page A-2

• LAN Port Pinouts, page A-3

• Console Port Connector Pinouts, page A-3

• G.SHDSL Port Connector Pinouts, page A-3

• Data BRI Port Connector Pinouts, page A-4

• Voice ISDN BRI Interface Pin Numbers and Functions, page A-4

• Cable Specifications, page A-5

Warning

Note For compliance and safety information, see the Regulatory Compliance and Safety Information

Ultimate disposal of this product should be handled according to all national laws and regulations.

Statement 1040

Roadmap that was shipped with the router and the

Cisco 800 Series and SOHO Series Routers.

Router Specifications

Table A-1 lists the system specifications for the routers.

Ta b l e A-1 Router Specifications

Description Design Specification Physical Dimensions

Dimensions with antenna and rubber feet (H

x W x D)

Weight (not including desktop power supply) 5.5 lb (2.5 kg) maximum

Regulatory Compliance and Safety Information for

1.9 x 12.8 x 10.4 in.

OL-16193-01

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

A-1

Wireless Access Point

Appendix A Technical Specifications

Table A-1 Router Specifications

Description Design Specification Environmental Operating Ranges

Nonoperating temperature –4 to 149°F (–20 to 65°C)

Nonoperating humidity 5 to 95% relative humidity

Nonoperating altitude 0 to 15,000 ft (4570 m)

Operating temperature 32 to 104°F (0 to 40°C)

Operating humidity 10 to 85% relative humidity

Operating altitude 0 to 10,000 ft (3000 m)

Noise criterion NC- 33; less than or equal to 32 dBA

Router Power Adapter

Input voltage 85 to 264 VAC

Input frequency 47 to 63 Hz

Power output 60 W maximum

Output voltages +12 VDC

Inline Power-over-Ethernet Adapter

Input voltage 85 to 264 VAC

Input frequency 47 to 63 Hz

Power output 80W maximum

Output voltage –48 VDC

Wireless Access Point

Table A-2 lists the specifications for the wireless access point (AP).

Ta b l e A-2 Wireless Access Point Specifications

Description Design Specification

Radio technology IEEE 802.11n draft 2.0 standard compliant. 2x3

Operating frequency 2.4-GHz radio band

Channels Country-specific 20 and 40 MHz

PHY Data rate 802.11b up to 11 Mbps

MIMO radio. Backward compatible with

802.11b/g.

802.11g up to 54 Mbps

802.11n up to 300 Mbps

A-2

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

OL-16193-01

Appendix A Technical Specifications

LAN Port Pinouts

Table A-3 provides pinouts for the Ethernet LAN port.

Ta b l e A-3 Ethernet LAN Port Pinouts

Pin Function

1 RX+

2 RX–

3 TX+

4 Unused

5 Unused

6 TX–

7 Unused

8 Unused

LAN Port Pinouts

Console Port Connector Pinouts

Table A-4 provides pinouts for the console connector (for connecting a terminal or PC).

Ta b l e A-4 Console Connector Pinouts (RJ-45-to-DB-9)

RJ-45 Pin Function

1 RTS

2 DTR

3 TXD

4 GND

5 GND

6 RXD

7 DSR

8 CTS

G.SHDSL Port Connector Pinouts

Table A-5 provides pinouts for the (global industry standard) symmetrical high-speed DSL (G.SHDSL)

WAN port.

OL-16193-01

Ta b l e A-5 G.SHDSL WAN Port Pinouts

Pin Function

1 Unused

2 TIP (Port1)

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

A-3

Data BRI Port Connector Pinouts

Table A-5 G.SHDSL WAN Port Pinouts

Pin Function

3 TIP (Port0)

4 TIP (Port0)

5 TIP (Port1)

6 Unused

Data BRI Port Connector Pinouts

Table A-6 provides pinouts for the Data BRI port.

Ta b l e A-6 Data BRI Port Pinouts

Pin Function

1 Unused

2 Unused

3 TXP

4 RXP

5 TXN

6 TXN

7 Unused

8 Unused

Appendix A Technical Specifications

Voice ISDN BRI Interface Pin Numbers and Functions

Table A-7 provides the interface pin numbers and functions for the voice ISDN BRI port.

Ta b l e A-7 Interface Pin Numbers and Functions

A-4

ISDN BRI NT/TE Card NT Interface

Pin 3/T+ Pin 3/R+ Pin 3/T+

Pin 4/R+ Pin 4/T+ Pin 4/R+

Pin 5/R- Pin 5/T- Pin 5/R-

Pin 6/T- Pin 6/R- Pin 6/T-

1. Use a straight-through cable for NT interfaces.

2. Use a crossover cable for TE interfaces.

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

TE Interface

OL-16193-01

Appendix A Technical Specifications

Cable Specifications

This section provides specifications for the following Ethernet cables:

• Straight-through cable

• Crossover cable

Because of the autocrossover (autosensing) function, both straight-through and crossover cables can be used for the Ethernet LAN port.

Ethernet Cable Specifications

Table A-8 provides specifications that apply to both straight-through and crossover Ethernet cables.

Ta b l e A-8 Ethernet Cable Specifications

Ty pe Category

10BASE-T Category 3 or 5

100BASE-T Category 5 or higher

Cable Specifications

Maximum Cable Length

The maximum length for the Ethernet cables that connect equipment to the router is 328 ft (100 m). This length is also the maximum distance between the router and the equipment connected to it.

OL-16193-01

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

A-5

Cable Specifications

Appendix A Technical Specifications

A-6

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

OL-16193-01

Cisco Systems 880, HIG880, C892FSPK9, 861WGNPK9RF, 861W User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

Preface

Product Overview

General Description

Cisco 860 Series ISRs

Cisco 880 Series ISRs

Cisco 880 Series Data Routers

Cisco 880 Series Voice Routers

Hardware Features

Kensington Lock

Reset Button

LEDs

Memory

USB Port

Power over Ethernet Module

3G Cellular Data WAN Connectivity

Wireless LAN Connectivity

Feature Summary

Installing the Router

Equipment, Tools, and Connections

Items Shipped with your Router

Additional Items

Connections

Ethernet Devices

Installing the Router

Installing on a Table

Mounting on a Wall

Installing the Router Ground Connection

Connecting the Router

Preparing to Connect the Router

Preventing Damage to the Router

Connecting a PC, Server, or Workstation

Connecting a Phone

Connecting an External Ethernet Switch

Connecting a Terminal or PC to the Console Port

Terminal Emulator Settings

Connecting a Data BRI Port

Connecting Power over Ethernet

Connecting the AC Adapter

Connecting an FXS line

Connecting a FXO Line

Connecting a Voice ISDN BRI Line

Verifying Connections

Initial Configuration

Cisco Configuration Professional Express

Cisco IOS CLI

Setup Command Facility

Verifying the Initial Configuration

Initial Configuration of the Wireless Access Point

Technical Specifications

Router Specifications

Wireless Access Point

LAN Port Pinouts

Console Port Connector Pinouts

G.SHDSL Port Connector Pinouts

Data BRI Port Connector Pinouts

Voice ISDN BRI Interface Pin Numbers and Functions

Cable Specifications

Ethernet Cable Specifications

Maximum Cable Length