Cisco Systems 1130AG User Manual

APPENDIX
B
Declarations of Conformity and Regulatory Information
This appendix contains the following sections:
Manufacturers Federal Communication Commission Declaration of Conformity Statement,
page B-2
Industry Canada, page B-4
European Community, Switzerland, Norway, Iceland, and Liechtenstein, page B-4
Declaration of Conformity for RF Exposure, page B-7
Guidelines for Operating Cisco Aironet Access Points in Japan, page B-8
Administrative Rules for Cisco Aironet Access Points in Taiwan, page B-9
Declaration of Conformity Statements, page B-11
OL-8369-05
Cisco Aironet 1130AG Series Access Point Hardware Installation Guide
B-1
Appendix B Declarations of Conformity and Regulatory Information

Manufacturers Federal Communication Commission Declaration of Conformity Statement

Manufacturers Federal Communication Commission Declaration of Conformity Statement
Tested To Comply With FCC Standards
FOR HOME OR OFFICE USE
Autonomous Access Point Models:
AIR-AP1131AG-A-K9 AIR-AP1131G-A-K9
Lightweight Access Point Models:
AIR-AP1131AG-A-K9 AIR-AP1131G-A-K9 AIR-LAP1131G-A-K9
FCC Certification numbers:
LDK102054 LDK102054E LDK102065
Manufacturer:
Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA
This device complies with Part 15 rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and radiates radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference. However, there is no guarantee that interference will not occur. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from which the receiver is connected.
Consult the dealer or an experienced radio/TV technician.
B-2
Cisco Aironet 1130AG Series Access Point Hardware Installation Guide
OL-8369-05
Appendix B Declarations of Conformity and Regulatory Information
Caution The Part 15 radio device operates on a non-interference basis with other devices operating at this
frequency when using the integrated antennas. Any changes or modification to the product not expressly approved by Cisco could void the user’s authority to operate this device.
Caution Within the 5.15 to 5.25 GHz band (5 GHz radio channels 34 to 48) the U-NII devices are restricted to
indoor operations to reduce any potential for harmful interference to co-channel Mobile Satellite System (MSS) operations.
Note Dynamic Frequency Selection (DFS) operation and operation from 5500 to 5700 MHz has
not been authorized as required by the rules of the Federal Communications Commission and is not supported until authorization is obtained.

VCCI Statement for Japan

VCCI Statement for Japan
Warning
This is a Class B product based on the standard of the Voluntary Control Council for Interference from Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the instruction manual.
OL-8369-05
Cisco Aironet 1130AG Series Access Point Hardware Installation Guide
B-3

Industry Canada

Industry Canada
Models:
AIR-AP1131AG-A-K9 / AIR-AP1131G-A-K9 AIR-LAP1131AG-A-K9 / AIR-LAP1131G-A-K9
Certification number:
2461B-102054

Canadian Compliance Statement

This Class B Digital apparatus meets all the requirements of the Canadian Interference-Causing Equipment Regulations.
Cet appareil numerique de la classe B respecte les exigences du Reglement sur le material broilleur du Canada.
This device complies with Class B Limits of Industry Canada. Operation is subject to the following two conditions:
Appendix B Declarations of Conformity and Regulatory Information
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired
operation.
Cisco Aironet 2.4-GHz Access Points are certified to the requirements of RSS-210 for 2.4-GHz spread spectrum devices, and Cisco Aironet 54-Mbps, 5-GHz Access Points are certified to the requirements of RSS-210 for 5-GHz spread spectrum devices.The use of this device in a system operating either partially or completely outdoors may require the user to obtain a license for the system according to the Canadian regulations. For further information, contact your local Industry Canada office.

European Community, Switzerland, Norway, Iceland, and Liechtenstein

Autonomous Access Point Models:
AIR-AP1131AG-E-K9 AIR-AP1131G-E-K9
Lightweight Access Point Models:
AIR-LAP1131AG-E-K9 AIR-LAP1131G-E-K9
B-4
Cisco Aironet 1130AG Series Access Point Hardware Installation Guide
OL-8369-05
Appendix B Declarations of Conformity and Regulatory Information
European Community, Switzerland, Norway, Iceland, and Liechtenstein

Declaration of Conformity with Regard to the 1999/5/EC (R&TTE Directive)

This declaration is only valid for configurations (combinations of software, firmware, and hardware) provided and supported by Cisco Systems. The use of software or firmware not provided and supported by Cisco Systems may result in the equipment no longer being compliant with the regulatory requirements.
OL-8369-05
Cisco Aironet 1130AG Series Access Point Hardware Installation Guide
B-5
Loading...
+ 9 hidden pages