Chrysler LH New Yorker, LHS, Concorde, Intrepid Vision and Supplements 1994 Service Manual – Front Suspension and Axle

SUSPENSION AND DRIVESHAFTS 2 - 1

SUSPENSION AND DRIVESHAFTS

CONTENTS

page page

DRIVESHAFTS ......................... 40

FRONT SUSPENSION ..................... 4

FRONT SUSPENSION SERVICE PROCEDURES . 6

GENERAL INFORMATION

Throughout this group, references may be made to
a particular L.H. platform vehicle by letter or number
designation. A chart showing the breakdown of these
designations is included in the Introduction section at
the front of this Service Manual.

The L.H. platform vehicles have a MacPherson gas
pressurized strut front suspension design (Fig. 1).
The MacPherson strut shock absorber assembly in­cludes the following components. A rubber isolated
top mount, seat and bearing assembly and a coil
spring insulator. The MacPherson strut assembly is
attached to the vehicle at the shock tower using 3
studs which are part of the isolated top mount. The
lower end of the MacPherson strut assembly is at­tached to the upper leg of the steering knuckle. At­tachment of the MacPherson strut assembly to the
steering knuckle is by 2 serrated bolts. A forged lower

GENERAL INFORMATION .................. 1

REAR SUSPENSION ..................... 53

SPECIFICATIONS ....................... 72

control arm assembly (Fig. 1) is attached to the front
cradle and steering knuckle. A tension strut (Fig. 1)
connects the lower control arm assembly to the front
cradle.

A sealed for life front hub and bearing assembly is
attached to the front steering knuckle. The outer C/V
joint assembly is splined to the front hub and bearing
assembly and is retained by a prevailing torque nut.

CAUTION: ONLY FRAME CONTACT HOISTING
EQUIPMENT CAN BE USED ON L.H. PLATFORM VE­HICLES. The L.H. platform vehicles have a fully in­dependent rear suspension. The L.H. platform ve­hicles can not be hoisted using equipment designed
to lift a vehicle by the rear axle. If this type of
hoisting equipment is used damage to rear suspen­sion components will occur.

2 - 2 SUSPENSION AND DRIVESHAFTS

Fig. 1 L.H. Platform Front Suspension

SUSPENSION AND DRIVESHAFTS 2 - 3

SUSPENSION/STEERING/DIAGNOSIS FRONT WHEEL DRIVE

2 - 4 SUSPENSION AND DRIVESHAFTS

FRONT SUSPENSION

FRONT SUSPENSION MAJOR COMPONENTS
(FIG. 2)

STRUT ASSEMBLY

The front strut and suspension of the vehicle is
supported by coil springs positioned around the
struts. The springs are contained between an upper
seat, located just below the top strut mount assembly
(Fig. 2) and a lower spring seat on the strut lower
housing.

The top of each strut assembly is bolted to the
upper fender reinforcement (shock tower) through a
rubber isolated mount.

The bottom of the strut assembly attaches to the
top of the steering knuckle with two serrated
through bolts and prevailing torque nuts. Caster is a
fixed setting (net build) on all vehicles and is not
adjustable.

STEERING KNUCKLE

The steering knuckle (Fig. 2) is a single casting
with legs machined for attachment to the front strut
assembly and lower control arm ball joint. The steer­ing knuckle also has machined abutments on the
casting to support and align the front brake caliper
assembly. The knuckle also holds the front drive
shaft outer C/V joint hub and bearing assembly. The
hub is positioned through the bearing and knuckle,
with the constant velocity stub shaft splined through
the hub. The outer C/V joint is retained to the hub
and bearing assembly using a prevailing torque nut.

LOWER CONTROL ARM

The lower control arm (Fig. 2) is a steel forging
with 2 rubber bushings isolating the lower control
arm from the front cradle assembly. The isolator
bushings consist of a metal encased pivot bushing
and a solid rubber tension strut bushing. The lower
control arm is bolted to the cradle assembly using a
pivot bolt through the center of the rubber pivot
bushing and at the tension strut isolator bushing
(Fig. 2).

The ball joint is an integral part of the control arm
and has a non-tapered stud with a notch for clamp

bolt clearance. The stud is clamped and locked into
the steering knuckle leg with a clamp bolt. The ball
joint used on the L.H. Platform vehicle is non­serviceable and if defective must be serviced as part
of the lower control arm.

DRIVESHAFTS

A left and right driveshaft is attached inboard to
the transaxle differential output (or stub) shaft, and
outboard to the driven wheel hub and bearing assem­bly.

To deliver driving force from the transaxle to the
front wheels during turning maneuvers and suspen­sion movement. Both shafts are constructed with con­stant velocity universal joints at both ends.

Both shafts have a Tripod (sliding) joint at the
transaxle end and C/V joints (with splined stub
shafts) on the hub ends. Due to the transaxle loca­tion the connecting shafts between the C/V joints are
of different length and construction. The left shaft is
longer than the right. Both the left and right drive
shafts are of the solid bar type. No tubular drive
shafts are used on any available L.H. platform ve­hicle and powertrain combinations.

TENSION STRUTS

The L.H. platform vehicle uses a tension strut (Fig.

2) on each side of the vehicles front suspension. The
tension strut controls longitudinal (for-and-aft) move­ment of the front wheels of the vehicles. Controlling
the longitudinal movement of the wheels reduces
harshness when wheels hit sudden irregularities in
the road surface.

STABILIZER BAR (SWAY BAR)

The stabilizer bar (Fig. 2) interconnects the front
strut assemblies of the vehicle. The purpose of a
stabilizer bar is to control the body roll of the vehicle.

STABILIZER BAR LINK ASSEMBLY

The stabilizer bar link assembly (Fig. 2) is used to
attach the stabilizer bar to the front strut assemblies.
This reduces the fore-and-aft rate of the sway bar
from the rest of the suspension.

SUSPENSION AND DRIVESHAFTS 2 - 5

Fig. 2 L.H. Platform Front Suspension

2 - 6 SUSPENSION AND DRIVESHAFTS

FRONT SUSPENSION SERVICE PROCEDURES

INDEX

page page

Ball Joints .............................. 20

Front Suspension Serviceable Components ...... 6

Front Wheel Alignment ......................6

Hub and Bearing Assembly ................. 34

Lower Control Arm Bushing Service ........... 18

Lower Control Arm Service .................. 12

Servicing Stabilizer Bar and Bushings .......... 21

FRONT SUSPENSION SERVICEABLE COMPONENTS

The following components may be replaced either

individually or as an assembly.

• Gas pressurized front strut must be replaced as an
assembly. The strut is not serviceable. It is not neces­sary to replace strut assemblies in pairs.

• Strut assembly upper mounts are replaceable.

• Bearing and seat assemblies may be replaced indi-

vidually.

• Coil springs may be replaced individually from the
strut assemblies.

• Coil spring lower isolator may be replaced indi­vidually.

• Front wheel hub and bearing assemblies are indi­vidually replaceable.

• Front lower control arm assemblies are replace­able. The ball joint is integral to the control arm and
will require replacement of the control arm if defec­tive. The ball joint seal is individually replaceable.

Lower control arm bushings are serviced as indi­vidual components of lower control arm assembly, and
do not require replacement of lower control arm if
defective.

• Tension struts are replaceable as are the tension
strut to cradle assembly isolator bushings. Tension
strut washers at the lower control arm and cradle are
replaceable, with proper approved replacement parts

ONLY.

• Front stabilizer bar is replaceable. Front stabilizer
bar isolator bushings, clamps and stabilizer bar link
assemblies are also replaceable.

• Driveshaft seal and boot replacement, is the only
service to be performed on the driveshaft assemblies.
Any failure of an internal driveshaft component will
require the replacement of the driveshaft assembly.

FRONT WHEEL ALIGNMENT

Front wheel alignment is the proper settings of all
the interrelated suspension angles affecting the run­ning and steering of the front wheels of the vehicle.

On the L.H. platform vehicle the only adjust­able suspension setting is wheel TOE.

Servicing Wheel Studs ..................... 37

Steering Knuckle Service ...................29

Strut Damper Assembly ..................... 7

Suspension Coil Springs ...................12

Tension Strut Service ...................... 15

Wheel Alignment Service Procedure ............ 7

The method of checking front alignment will vary
depending on the type of equipment being used. The
instructions furnished by the manufacturer of the
equipment should always be followed. With the excep­tion that the alignment specifications recommended
by Chrysler Corporation be used.

There are six basic factors which are the foundation
to front wheel alignment. These are vehicle height,
caster, camber, toe-in, steering axis inclination and
toe-out on turns. Of the six basic factors only TOE

IN is mechanically adjustable on the L.H. plat­form vehicle (Fig. 1).

CAUTION: Do not attempt to modify any suspension
or steering components by heating or bending of
the component.

Wheel alignment adjustments can only be
made for the Toe In setting on the L.H. platform
vehicles.

Toe is measured in degrees or inches and is the

distance the front edges of the tires are closer (or
farther apart) than the rear edges. See Front Wheel
Drive Specifications for Toe settings.

PRE-ALIGNMENT

Before any attempt is made to change or correct
front wheel alignment. The following inspection and
necessary corrections must be made on those parts
which influence the steering of the vehicle.

(1) Check and inflate tires to recommended pres­sure. All tires should be the same size and in good
condition and have approximately the same wear.
Note type of tread wear which will aid in diagnosing,
see Wheels and Tires, Group 22.

(2) Check front wheel and tire assembly for radial
runout.

(3) Inspect lower ball joints and all steering linkage
for looseness.

(4) Check for broken or front and rear springs.

Alignment must only be checked after the vehicle
has had the following checked or adjusted. Tires set

to recommended pressures, full tank of fuel, no pas­senger or luggage compartment load and is on a level
floor or alignment rack.

Just prior to each alignment reading. The vehicle
should be bounced (rear first, then front) by grasping
bumper at center and jouncing each end an equal
number of times. Always release bumpers at bottom
of down cycle.

SUSPENSION AND DRIVESHAFTS 2 - 7

Fig. 2 Front Wheel Toe Adjustment Location

Fig. 1 L.H. Platform Toe Adjustment

WHEEL ALIGNMENT SERVICE PROCEDURE

FRONT WHEEL TOE ADJUSTMENT

(1) Prepare vehicle as described in the Pre­Alignment procedure.

(2) Center steering wheel and hold with steering
wheel clamp.

(3) Loosen tie rod adjustment sleeve jamnuts. Ro­tate adjustment sleeve to align toe to specifications
(Fig. 2).

CAUTION: When setting Toe on vehicle, the maxi­mum dimension of exposed threads allowed on in­ner and outer tie rod can not exceed the distance
shown in (Fig. 3). If the maximum distance is ex­ceeded, inadequate retention of either inner or outer
tie rod may result. Ensure that adjustment sleeve
jam nuts are torqued to required specification when
Toe setting procedure is completed.

Fig. 3 Tie Rod Adjustment Sleeve Thread

Engagement

(4) Tighten tie rod adjustment sleeve locknuts to 75

Nzm (55 ft. lbs.) torque.

(5) Remove steering wheel clamp.

STRUT DAMPER ASSEMBLY

REMOVAL

(1)

Raise vehicle on jackstands or centered on a
frame contact type hoist. See Hoisting in the Lubri­cation and Maintenance section of this manual, for
the required lifting procedure to be used for this
vehicle.

(2) Remove front wheel and tire assembly from the

vehicle.

(3) Remove the stabilizer bar attaching link at the

strut assembly (Fig. 1).

(4) Loosen but do not remove the outer tie rod end
to strut assembly steering arm attaching nut (Fig. 2).
Then remove outer tie rod end from steering arm
using Puller, Special Tool MB-990635 or equivalent
(Fig. 2).

(5) If vehicle is equipped with Anti-Lock brakes.
Remove speed sensor cable routing bracket from front
strut assembly (Fig. 3).

(6) Remove brake caliper assembly from steering
knuckle and braking disc. Refer to the Brake Section

2 - 8 SUSPENSION AND DRIVESHAFTS

Fig. 1 Stabilizer Bar Link Removed From Strut

some other method, do not let caliper assembly hang
by brake hose (Fig. 4). Remove front braking disc
from hub.

Fig. 2 Removing Outer Tie Rod From Steering Arm

Fig. 4 Removal And Storage Of Front Caliper

CAUTION: The strut assembly to steering knuckle
bolts are serrated where they go through strut as­sembly and steering knuckle. When removing bolts,
turn nuts off bolts DO NOT TURN BOLTS IN STEER­ING KNUCKLE. If bolts are turned damage to steer­ing knuckle will result.

(7) Remove the strut assembly to steering knuckle
attaching bolts (Fig. 5).

Fig. 3 Speed Sensor Cable Routing Bracket

in this service manual for the required caliper re­moval and storage procedure. Support caliper assem­bly by hanging it from frame of vehicle with wire or

Fig. 5 Strut Assembly To Steering Knuckle

Attaching Bolts

SUSPENSION AND DRIVESHAFTS 2 - 9

(8) Remove the 3 strut assembly upper mount to
shock tower mounting nut and washer assemblies
(Fig. 6).

Fig. 6 Strut Assembly Mounting To Shock Tower

(9) Remove the strut assembly from the vehicle for
inspection and or disassembly.

INSPECTION

Inspect for evidence of fluid running from the upper
end of the reservoir. (Actual leakage will be a stream
of fluid running down the side and dripping off lower
end of unit). A slight amount of seepage between the
strut rod and strut shaft seal is not unusual and does
not affect performance of the strut assembly.

bly to steering knuckle attaching bolts (Fig. 7).
Torque the caliper assembly attaching bolts to 19
Nzm (192 in. lbs.).

Fig. 7 Front Disc Brake Caliper Mounting Bolts

(5) If the vehicle is equipped with Anti-Lock
brakes. Install the front speed sensor cable routing
bracket onto the front strut assembly (Fig. 3).

(6) Install outer tie rod on steering arm of strut
assembly (Fig. 8). Install tie rod to steering arm
attaching nut on tie rod. Torque the tie rod to steering
arm attaching nut to 37 Nzm (27 ft. lbs.).

(7) Install stabilizer bar link assembly onto strut
assembly (Fig. 8). Torque the stabilizer link assembly
to strut assembly attaching nut to 95 Nzm (70 ft. lbs.).

INSTALLATION

(1) Install front strut assembly into shock tower.

Install the 3 strut assembly upper mount to shock
tower attaching nuts (Fig. 6). Torque the 3 strut
mount to shock tower attaching nuts (Fig. 6) to 33
Nzm (25 ft. lbs.) torque.

(2) Position steering knuckle neck into strut assem-

bly.

CAUTION: The strut assembly to steering knuckle
bolts are serrated were they go through strut as­sembly and steering knuckle. When installing bolts,
turn nuts onto bolts DO NOT TURN BOLTS IN
STEERING KNUCKLE. If bolts are turned damage to
steering knuckle will result.

(3) Install the strut assembly to steering knuckle
attaching bolts (Fig. 5). Install nuts on attaching bolts
(Fig. 5). Torque the strut assembly to steering
knuckle attaching bolt nuts to 169 Nzm (125 ft. lbs.).

TURN NUTS ON BOLTS DO NOT TURN BOLTS.

Install braking disc back on front hub and

(4)
bearing assembly. Install front brake caliper assem­bly on steering knuckle. Install the 2 caliper assem-

Fig. 8 Tie Rod And Stabilizer Bar Link Installation

(8) Install the wheel and tire assembly.

(9) Tighten the wheel mounting stud nuts in proper
sequence (Fig. 9) until all nuts are torqued to half
specification. Then repeat the tightening sequence to
the full specified torque of 129 Nzm (95 ft. lbs.).

(10) Lower vehicle.

2 - 10 SUSPENSION AND DRIVESHAFTS

Fig. 9 Tightening Wheel Nuts

DISASSEMBLY (STRUT DAMPER)

The front strut is not serviced and must be replaced
as an assembly if found to be defective. The strut is
available with 2 calibrations, be sure strut is replaced
with an assembly of the same calibration.

The components of the strut assembly listed below
are replaceable if found to be defective.

• Coil spring (Coil springs come in a standard and
high rate be sure spring is replaced with a spring of
the correct rate.)

• Dust shield

• Mount assembly

• Seat And Bearing

• Jounce Bumper

• Lower Spring Isolator

• Shaft Nut

(1) Remove strut assembly requiring service from
the vehicle. Refer to Strut Assembly Removal in Ser­vicing Rear Struts, in this section of the service
manual.

(2) Position strut assembly in a vise, by clamping
strut assembly by the steering arm (Fig. 1). Using
paint or equivalent, mark the strut unit, lower spring
isolator, spring and upper strut mount for indexing of
the parts at assembly.

(3) Position Spring Compressors, Special Tool
C-4838 on the strut assembly spring (Fig. 1). Com­press coil spring until all load is removed from upper
strut mount assembly.

(4) Install Strut Rod Socket, Special Tool, L-4558 or
L-4558A on strut shaft nut (Fig. 2). Using a 10 mm
socket on end of strut shaft to keep strut shaft from
turning (Fig. 2), remove strut shaft nut.

(5) Remove upper strut mount assembly from strut
shaft (Fig. 3).

Fig. 1 Compressing Strut Assembly Coil Spring

Fig. 2 Remove Strut Shaft Nut

Fig. 3 Upper Strut Mount Removal

(6) Remove the jounce bumper and the seat/bearing
and dust shield as an assembly, from the strut assem­bly (Fig. 4).

Fig. 4 Jounce Bumper and Seat/Bearing And Dust

Shield

(7) Remove the coil spring and the spring compres­sor as an assembly from the strut unit (Fig. 5).

SUSPENSION AND DRIVESHAFTS 2 - 11

Fig. 6 Lower Spring Isolator

(2) Install compressed coil spring onto strut assem­bly aligning paint mark on spring with paint mark on
strut assembly (Fig. 7).

Fig. 5 Removing Coil Spring And Compressor From

Strut

(8) Remove lower spring isolator from strut assem-

bly lower spring seat (Fig. 6).

Inspect all disassembled components for signs of
abnormal wear or failure replacing any components
as required. Inspect strut unit for signs of abnormal
oil leakage and for loss of gas charge. To check for loss
of gas charge in strut unit. Push strut shaft into body
of strut and release, strut shaft should return to its
fully extended position. If strut shaft does not return
to its fully extended position replace strut unit.

STRUT REASSEMBLY

(1) Install original or new, lower spring isolator on
strut unit (Fig. 6).

Fig. 7 Spring Installation On Strut Assembly

(3) Install the strut bearing into the bearing seat
(Fig. 8). Bearing must be installed into seat with
notches on bearing facing down (Fig. 8).

Fig. 8 Bearing Installation Into Seat

2 - 12 SUSPENSION AND DRIVESHAFTS

(4) Lower seat/bearing and dust shield onto strut
assembly and spring. Align paint mark on
seat/bearing and dust shield, with paint mark on the
strut spring (Fig. 9).

(7) Install Strut Rod Socket, Special Tool, L-4558 or
L-4558A on strut shaft nut (Fig. 2). Using a 10 mm
socket on end of strut shaft to keep strut shaft from
turning (Fig. 2), torque strut shaft nut to 94 Nzm (70
ft. lbs.).

(8) Equally loosen the Spring Compressors, Special
Tool C-4838 until spring is seated on upper strut
mount and all tension is relieved from the spring
compressors.

(9) Install the strut assembly back into the vehicle.
Refer to Strut Assembly Removal in Servicing Front
Struts in this section of the service manual.

SUSPENSION COIL SPRINGS

Springs are rated separately for each side of vehicle
depending on optional equipment and type of service.
During service procedures where both springs are
removed, mark springs (Chalk, Tape, etc.) (Fig. 11) to
ensure installation in original position. If the coils
springs require replacement. Be sure that the

springs needing replacement, are replaced with
springs meeting the correct load and spring
rate for the vehicle.

During service procedures requiring the re­moval or installation of a coil spring with
Spring Compressor, Special Tool C-4838. It is
required that five coils be captured within the
jaws of the tool (Fig. 11).

Fig. 9 Seat/Bearing And Dust Shield Installation

(5) Install original or replacement jounce bumper

onto shaft of strut assembly (Fig. 10).

Fig. 10 Jounce Bumper Installation

(6) Install the upper strut mount assembly onto the
strut shaft, aligning paint marks (Fig. 3). Install the
upper strut mount to strut shaft retaining nut on
strut shaft.

Fig. 11 Identifying Coil Springs

LOWER CONTROL ARM SERVICE

The lower control arm if damaged, is serviced only
as a complete component. Do not attempt to repair or
straighten a broken or bent lower control arm.

The only serviceable components of the lower con­trol arm are, the pivot bushing, ball joint seal and
tension strut bushing. The service procedure to re­place these components is detailed in the specific
component sections of this group.

REMOVAL (ASSEMBLY)

(1) Raise vehicle on jackstands or centered on a
frame contact type hoist. See Hoisting in the Lubrica­tion and Maintenance section of this manual, for the
required lifting procedure to be used for this vehicle.

(2) Remove the wheel and tire assembly from the
vehicle.

(3) Remove the ball joint stud to steering knuckle
clamp nut and bolt (Fig. 1).

SUSPENSION AND DRIVESHAFTS 2 - 13

Fig. 2 Separating Ball Joint From Steering Knuckle

Fig. 1 Control Arm To Steering Knuckle Attachment

CAUTION: When lower control arm is separated
from steering knuckle, do not let ball joint seal hit
up against steering knuckle. If ball joint seal hits
steering knuckle, seal damage may occur. If ball
joint seal becomes torn, replace seal before assem­bling lower control arm to knuckle.

(4) Carefully insert a pry bar between lower control
arm and steering knuckle (Fig. 2). Push down on pry
bar to separate ball joint stud from steering knuckle
(Fig. 2). Note: Use caution when separating ball

joint stud from steering knuckle so ball joint
seal does not get cut.

CAUTION: Pulling steering knuckle out from vehicle
after releasing from ball joint can separate inner C/V
joint. See Driveshafts.

(5) Remove tension strut to cradle attaching nut
and washer from end of tension strut (Fig. 3). When
removing tension strut nut, keep strut from turning
by holding tension strut at flat using open end
wrench (Fig. 3). Discard tension strut to cradle

retaining nut. A NEW tension strut to cradle nut
must be used when installing tension strut.

(6) Loosen and remove lower control arm pivot
bushing to cradle assembly pivot bolt (Fig. 4).

Fig. 3 Tension Strut To Cradle Mounting

Fig. 4 Lower Control Arm Pivot Bolt

2 - 14 SUSPENSION AND DRIVESHAFTS

(7) Separate lower control arm and tension strut
from the cradle as an assembly. Lower control arm is
removed from cradle, by first removing pivot bushing
from cradle and then sliding tension strut out of
isolator bushing (Fig. 5).

Fig. 5 Lower Control Arm Removal From Cradle

Inspect lower control arm and tension strut (Fig. 6)
for distortion. Check all bushings for signs of sever
deterioration. Replace any bushings that show signs
of sever deterioration.

CAUTION: Pulling steering knuckle out from vehicle
after releasing from ball joint can separate inner C/V
joint. See Driveshafts.

CAUTION: When ball joint stud is installed into
steering knuckle, do not let ball joint seal hit up
against steering knuckle. If ball joint seal hits steer­ing knuckle, seal damage may occur. If ball joint
seal becomes torn, replace seal before assembling
lower control arm to knuckle.

(4) Install lower ball joint stud into steering
knuckle. Install steering knuckle to lower ball joint
stud, clamp bolt and nut into steering knuckle (Fig.

7). Torque clamp bolt to 55 Nzm (40 ft. lbs.).

Fig. 6 Lower Control Arm And Tension Strut

INSTALLATION (ASSEMBLY)

(1) Install the lower control arm on the cradle us­ing the following sequence. Install tension strut and
isolator bushing into cradle first, then install lower
control arm pivot bushing into bracket on cradle (Fig.

5).

(2) Install the lower control arm to cradle bracket
attaching bolt and nut (Fig. 4). Do not tighten the

lower control arm to cradle bracket attaching
bolt at this time.

(3) Install washer on end of tension strut (Fig. 3).
Install a NEW tension strut to cradle bracket nut, on
tension strut (Fig.3). Torque tension strut to cradle
bracket retaining nut to 150 Nzm (110 ft. lbs.). When
torquing tension strut nut, keep tension strut from
turning by holding tension strut at flat using an open
end wrench (Fig. 3).

Fig. 7 Control Arm To Steering Knuckle Attachment

(5) Install the wheel and tire assembly.

(6) Tighten the wheel mounting stud nuts in proper
sequence (Fig. 8) until all nuts are torqued to half
specification. Then repeat the tightening sequence to
the full specified torque of 129 Nzm (95 ft. lbs.).

Fig. 8 Tightening Wheel Nuts

(7) Lower vehicle so the suspension is supporting
vehicles weight (control arm at design height). Torque
the lower control arm pivot bushing to cradle bracket
attaching bolt (Fig. 9) to 123 Nzm (90 ft. lbs.).

Fig. 9 Lower Control Arm Pivot Bolt

TENSION STRUT SERVICE

To remove tension strut from vehicle for replace­ment, the tension strut and lower control arm first
MUST be removed as an assembly from the vehicle.

SUSPENSION AND DRIVESHAFTS 2 - 15

Fig. 10 Tension Strut Installed In Lower Control

Arm.

When torquing tension strut nut, keep tension strut
from turning by holding tension strut at flat using an
open end wrench (Fig. 11).

TENSION STRUT

REMOVAL AND REPLACEMENT

(1) Remove lower control arm and tension strut as
an assembly from the vehicle. See Lower Control Arm
Removal in this section of the service manual for the
required removal procedure.

(2) Separate the tension strut from the lower con-

trol arm assembly.

(3) Inspect tension strut bushing in lower control
arm for excessive wear or deterioration. If tension
strut bushing is found to be defective replace lower
control tension strut bushing at this time. Refer to
Lower Control Arm Bushing Service in this section of
the service for tension strut removal and installation
procedure.

(4) Install replacement tension strut into tension
strut bushing on lower control arm assembly. Position
tension strut in lower control as shown in (Fig. 10),
with word FRONT stamped in tension strut posi­tioned away from control arm (Fig. 10). With an open
end wrench on flat of tension strut to keep tension
strut from turning. Torque NEW tension strut to
lower control retaining nut to 150 Nzm (110 ft. lbs.).

(5) Install lower control arm and tension strut as
an assembly back on the vehicle. See Lower Control
Arm Installation in this section of the service manual
for the required installation procedure.

(6) Install washer on end of tension strut (Fig. 11).
Install a NEW tension strut to cradle bracket nut, on
tension strut (Fig. 11). Torque the tension strut to
cradle bracket retaining nut to 150 Nzm (110 ft. lbs.).

Fig. 11 Tension Strut To Cradle Mounting

(7) Install the wheel and tire assembly.

(8) Tighten the wheel mounting stud nuts in proper
sequence (Fig. 12) until all nuts are torqued to half
specification. Then repeat the tightening sequence to
the full specified torque of 129 Nzm (95 ft. lbs.).

(9) Lower vehicle so the suspension is supporting ve­hicles weight (control arm at design height). Torque the
lower control arm pivot bushing to cradle bracket attach­ing bolt (Fig. 13) to 123 Nzm (90 ft. lbs.).

TENSION STRUT TO CRADLE BUSHING

REMOVE

To remove tension strut to cradle bushings from
vehicle for replacement, the tension strut and lower
control arm first MUST be removed as an assembly
from the vehicle.

(1) Remove lower control arm and tension strut as

2 - 16 SUSPENSION AND DRIVESHAFTS

Fig. 12 Tightening Wheel Nuts

an assembly from the vehicle. See Lower Control Arm
Removal in this section of the service manual for the
required removal procedure.

bushing from tension strut. Install replacement isola­tor bushing on tension strut until it is seated against
retaining washer (Fig. 14).

tor bushing from the cradle assembly. Install replace­ment tension strut to cradle isolator bushing into
cradle, until squarely seated against cradle assembly
(Fig. 15).

Fig. 13 Lower Control Arm Pivot Bolt

(2) Remove failed tension strut to cradle, isolator

(3) Remove the failed tension strut to cradle isola-

Fig. 14 Tension Strut Bushing Installed On Tension

Strut

Fig. 15 Tension Strut Bushing Installed In Cradle

When torquing tension strut nut, keep tension strut
from turning by holding tension strut at flat using an
open end wrench (Fig. 16).

INSTALL

(1) Install lower control arm and tension strut as
an assembly back on the vehicle. See Lower Control
Arm Installation in this section of the service manual
for the required installation procedure.

(2) Install washer on end of tension strut (Fig. 16).
Install a NEW tension strut to cradle bracket nut, on
tension strut (Fig. 16). Torque the tension strut to
cradle bracket retaining nut to 150 Nzm (110 ft. lbs.).

Fig. 16 Tension Strut To Cradle Mounting

(3) Install the wheel and tire assembly.

(4)

Tighten the wheel mounting stud nuts in
proper sequence (Fig. 17) until all nuts are torqued
to half specification. Then repeat the tightening se­quence to the full specified torque of 129 Nzm (95 ft.
lbs.).

Fig. 17 Tightening Wheel Nuts

(5)

Lower vehicle so the suspension is supporting
vehicles weight (control arm at design height).
Torque the lower control arm pivot bushing to cradle
bracket attaching bolt (Fig. 18) to 123 Nzm (90 ft.
lbs.).

SUSPENSION AND DRIVESHAFTS 2 - 17

(2) Separate the tension strut from the lower con-

trol arm assembly (Fig. 19).

Fig. 19 Tension Strut And Lower Control Arm

Bushing

(3) Replace tension strut to lower control arm isola­tor bushing. Refer to Lower Control Arm Bushing
Service in this section of the service manual for ten­sion strut isolator bushing removal and installation
procedure.

(4) Install tension strut into tension strut bushing
on lower control arm assembly. Position tension strut
in lower control arm as shown in (Fig. 20), with word
FRONT stamped in tension strut positioned away
from control arm (Fig. 20). With an open end wrench
on flat of tension strut, to keep tension strut from
turning. Torque NEW tension strut to lower control
arm retaining nut to 150 Nzm (110 ft. lbs.)

Fig. 18 Lower Control Arm Pivot Bolt

TENSION STRUT TO LOWER CONTROL ARM BUSHING

To remove tension strut to lower control arm bush­ing for replacement, the tension strut and lower con­trol arm MUST first be removed as an assembly from
the vehicle.

REMOVE

(1) Remove lower control arm and tension strut as
an assembly from the vehicle. See Lower Control Arm
Removal in this section of the service manual for the
required removal procedure.

Fig. 20 Tension Strut Installed In Lower Control

Arm.

INSTALL

(1) Install lower control arm and tension strut as
an assembly back on the vehicle. See Lower Control
Arm Installation in this section of the service manual
for the required installation procedure.

2 - 18 SUSPENSION AND DRIVESHAFTS

(2) Install washer on end of tension strut (Fig. 21).
Install a NEW tension strut to cradle bracket nut, on
tension strut (Fig. 21). Torque the tension strut to
cradle bracket retaining nut to 150 Nzm (110 ft. lbs.).
When torquing tension strut nut, keep tension strut
from turning by holding tension strut at flat using an
open end wrench (Fig. 21).

Fig. 21 Tension Strut To Cradle Mounting

(3) Install the wheel and tire assembly.

(4) Tighten the wheel mounting stud nuts in proper
sequence (Fig. 22) until all nuts are torqued to half
specification. Then repeat the tightening sequence to
the full specified torque of 129 Nzm (95 ft. lbs.).

Fig. 23 Lower Control Arm Pivot Bolt

LOWER CONTROL ARM BUSHING SERVICE

PIVOT BUSHING

REMOVE

To perform removal and replacement of the lower
control arm pivot bushing. The control arm and ten­sion strut assembly must be removed from the ve­hicle. The removal and replacement of the lower con­trol arm pivot bushing must be performed using an
arbor press.

(1) Remove lower control arm and tension strut as
an assembly from the vehicle. See Lower Control Arm
Removal in this section of the service manual for the
required removal procedure.

(2) Separate the tension strut from the lower con­trol arm assembly.

(3) Position lower control arm in arbor press with
large end of pivot bushing inside Receiver, Special
Tool MB-990799, and special tool supporting lower
control arm (Fig. 1). Position Remover, Special Tool,
6642-2 on top of pivot bushing (Fig. 1). Using arbor
press, press on lower control arm pivot bushing until
it falls free of lower control arm.

(4) Remove the pressed out lower control arm pivot
bushing from the Receiver, Special Tool MB-990799
and discard.

Fig. 22 Tightening Wheel Nuts

(5) Lower vehicle so the suspension is supporting
vehicles weight (control arm at design height). Torque
the lower control arm pivot bushing to cradle bracket
attaching bolt (Fig. 23) to 123 Nzm (90 ft. lbs.).

INSTALL

(1) Turn the lower control arm over in the arbor
press. So it is positioned on Receiver, Special Tool,
MB-990799 as shown in (Fig. 2).

Position new pivot bushing in lower control

(2)
arm so it is square with the bushing hole. Position
Installer, Special Tool 6644-1 on top of pivot bushing,
with pivot bushing setting in recessed area of In­staller (Fig. 2). Bring down ram of arbor press until
it is close to Installer, Special Tool. Then square face

SUSPENSION AND DRIVESHAFTS 2 - 19

Fig. 1 Lower Control Arm Pivot Bushing Removal

of Installer, Special Tool 6644-1 with end of ram on
arbor press and start to press bushing into lower
control arm.

Fig. 2 Installing Lower Control Arm Pivot Bushing

(3) Press lower control arm pivot bushing into
lower control arm until Installer, Special Tool 6644-1
squarely bottoms against surface of lower control arm
(Fig. 3). When Installer, Special Tool, 6644-1

squarely touches surface of control arm stop
installing bushing. When Installer, Special Tool

6644-1 squarely bottoms on control arm, bushing is
installed to the correct position in control arm.

(4) Install tension strut into tension strut bushing
on the lower control arm assembly. Position tension
strut in lower control as shown in (Fig. 4), with word
FRONT stamped in tension strut positioned away
from control arm. With an open end wrench on flat of
tension strut to stop tension strut from turning.
Torque NEW tension strut to lower control retaining
nut to 150 Nzm (110 ft. lbs.)

(5) Install lower control arm and tension strut as
an assembly back on the vehicle. See Lower Control

Fig. 3 Pivot Bushing Installed In Lower Control Arm

Fig. 4 Tension Strut Installed In Lower Control Arm.

Arm Installation in this section of the service manual
for the required installation procedure.

TENSION STRUT BUSHING

REMOVE

To perform removal and replacement of the lower
control arm tension strut bushing. The control arm
and tension strut assembly must be removed from the
vehicle. The removal and replacement of the lower
control arm tension strut bushing must be performed
using an arbor press.

(1) Remove lower control arm and tension strut as
an assembly from the vehicle. See Lower Control Arm
Removal in this section of the service manual for the
required removal procedure.

(2) Separate the tension strut from the lower con­trol arm assembly.

(3) Position lower control arm in arbor press with
tension strut bushing inside Receiver, Special Tool
MB-990799 and special tool supporting lower control
arm (Fig. 5). Position Remover, Special Tool, 6644-4
on top of tension strut bushing (Fig. 5). Using the ar-

2 - 20 SUSPENSION AND DRIVESHAFTS

bor press, press Remover, Special Tool, 6644-4 down
through the tension strut bushing until the arbor
press can push it no farther. As Remover, Special
Tool, 6644-4 is pressed down through tension strut
bushing it will cut the bushing into two pieces.

Fig. 5 Removing Lower Control Arm Tension Strut

Bushing

(4) Remove lower control arm assembly from arbor
press. Remove pieces of tension strut and Remover,
Special Tool 6644-4, from lower control arm.

INSTALL

(1) Thoroughly lubricate the replacement tension
strut bushing, lower control arm and Installer, Spe­cial Tool 6644-3 using Mopart Silicone Spray Lube or
an equivalent.

(2) By hand, install tension strut bushing into large
end of Installer, Special Tool 6644-3. Press bushing

into installer as far as it will go by hand.

(3) Position lower control arm in arbor press, so
tension strut hole in lower control arm is centered on
Receiver, Special Tool MB-990799. (Fig. 6). Position
Installer, Special Tool 6644-3 with previously in­stalled bushing, inside of tension strut bushing hole
in lower control arm (Fig. 6). Position Installer, Spe­cial Tool 6644-2 on top of tension strut bushing (Fig.

6). Using the arbor press, press the tension strut
bushing into the lower control arm. As the bushing is
being pressed into the control arm a pop will be
heard. When the pop is heard Installer, Special Tool
6644-3 will slightly move up off the control arm. At
this time remove the control arm assembly from the
arbor press and pull Special Tool 6644-3 off the ten­sion strut bushing in the control arm. Tension strut
bushing is now installed.

Fig. 6 Installing Tension Strut Bushing Into Lower

Control Arm

joint is found to be defective, the entire lower control
arm will need to be replaced. Do not attempt any type
of repair on the ball joint assembly.

INSPECTION BALL JOINT WEAR

Raise front of vehicle using jack stands or a frame
contact type hoist, until front suspension is in full
rebound and tires are not in contact with the ground.
Grasp tire at top and bottom, and apply an in and out
on the wheel and tire. While applying force to the
tire, look for any movement between the lower ball
joint and lower control arm. If any movement is evi­dent the lower ball joint is worn and the lower control
arm requires replacement.

BALL JOINT SEAL INSTALLATION

(1) By hand, initially install the ball joint seal on
the lower control arm.

(2) Lower control arm is to be supported using a 1
1/4 inch socket (Fig. 7). Position the 1 1/4 inch socket,
lower control arm and Seal Installer, Special Tool
MB-990800 in an arbor press (Fig. 7).

BALL JOINTS

The lower front suspension ball joints operate with
no free play. See Inspection Ball Joint Wear to deter­mine if the ball joint is worn and requires replacement.

The ball joints are not replaceable as a separate
component of the lower control arm assembly. If a ball

Fig. 7 Installing Ball Joint Seal

SUSPENSION AND DRIVESHAFTS 2 - 21

(3) Using Installer, Special Tool MB-990800, press
seal onto ball joint housing until it is squarely seated
against top surface of control arm (Fig. 7).

SERVICING STABILIZER BAR AND BUSHINGS

The stabilizer bar interconnects the front MacPher­son strut assemblies of the vehicle and attaches to the
front cradle of the vehicle (Fig. 1).

Jounce and rebound movements affecting one wheel
are partially transmitted to the opposite wheel to
stabilize body roll.

Attachment of stabilizer bar to cradle assembly, is
through rubber-isolated bushings (Fig. 1). Stabilizer
bar to strut assembly attachment is done utilizing a
stabilizer bar link (Fig. 1).

All parts are serviceable, and the stabilizer bar to
cradle isolator bushings are split for easy removal
and installation. The split in the stabilizer bar to
crossmember bushing should be positioned toward the
front of the vehicle.

2 - 22 SUSPENSION AND DRIVESHAFTS

Fig. 1 Front Stabilizer Bar And Stabilizer Bar Mounting

SUSPENSION AND DRIVESHAFTS 2 - 23

STABILIZER BAR ISOLATOR BUSHING SERVICE

If only the stabilizer bar isolator bushings require
service without any service to the stabilizer bar. The
stabilizer bar isolator bushings can be removed from
the stabilizer bar without requiring the stabilizer bar
to be removed from the vehicle.

ISOLATOR BUSHING REMOVAL

(1) Remove the 2 bolts each, attaching the stabi­lizer bushing retainer and bushing to cradle assembly
(Fig. 2).

stabilizer bar, so lower part of stabilizer bar is cen­tered in the middle of the cradle assembly. Failure to
do this may cause stabilizer bar to come in contact
with other suspension components.

(2) Align the stabilizer bar bushing retainers with

the mounting holes in the cradle assembly (Fig. 2).

Install but do not tighten the 4 bushing retainer
to cradle assembly mounting bolts. The 4 retain­ing bolts will be torqued when vehicle is low­ered to the ground.

(3) Lower vehicle to the ground.

(4) With the full weight of the vehicle supported by
the suspension. Use a long extension, and torque the
4 stabilizer bar bushing retainer to cradle assembly
attaching bolts to 55 Nzm (40 ft. lbs.).

STABILIZER BAR REMOVAL

When removing the front stabilizer bar from the
L.H. platform vehicle, it is necessary to remove the
entire front cradle module (Fig. 4) from vehicle.

Fig. 2 Stabilizer Bar Isolator Bushing Attachment To

Cradle

(2) Remove the stabilizer bar isolator bushing re-

tainers from the isolator bushings.

(3) Inspect for broken or distorted retainers and

bushings. If bushing replacement is required, bushing
can be removed by opening slit in bushing and remov­ing bushing from around stabilizer bar. The stabilizer
bar to cradle assembly bushings, should be positioned
on stabilizer bar, so slit in bushing is positioned to­ward front of vehicle (Fig. 3).

Fig. 3 Isolator Bushings Installed On Stabilizer Bar

ISOLATOR BUSHING INSTALLATION

(1) Install the isolator bushing retainers back on

the stabilizer bar isolator bushings.

CAUTION: When stabilizer bar is installed. Position

Fig. 4 L.H. Platform Front Cradle

SUPPORTING ENGINE

To allow for removal of the cradle module assembly
from the vehicle. It will be necessary to support the
engine and transaxle assembly using Fixture, Engine
Support, Special Tool 7137 or equivalent. Refer to
(Fig. 5 to 9) for engine supporting locations depending
on engine application.

CAUTION: No attempt should be made to support or
lift either engine application using the intake mani­fold, or any other location on engine not specified
below.

3.3 LTR ENGINE

(1) Mount Fixture, Engine Support Special Tool
7137 or equivalent across engine compartment (Fig.

5). Using nylon webbing material such as seat belt

2 - 24 SUSPENSION AND DRIVESHAFTS

material or equivalent, mount it to the following loca­tions on the 3.3 ltr. engine.

(2) Remove bolt attaching A/C compressor bracket
to front of engine. Install webbing material hook on
A/C compressor bolt, install bolt and tighten (Fig. 5
and 6).

(3) Loosen but do not remove generator to engine
mounting bolt, remove spacer between generator and
engine. Install webbing material hook between gen­erator and engine, re-install and tighten original bolt
(Fig. 5 and 6).

(4) Remove electronic ignition coil, mounting
bracket bolt from rear of engine. Install webbing ma­terial hook on bracket bolt and re-install and tighten
bolt. Note: Route webbing material between fuel

injector rail and valve cover, not between fuel
injector rail and intake manifold.

(5) Mount remaining piece of webbing material to
left cylinder head using threaded hole on back of
cylinder head. Using a bolt of the correct thread size
and length, install webbing hook on bolt. Then install
bolt into threaded hole on back of cylinder head and
tighten bolt.

(6) Securely attach pieces of webbing material to
hook on engine holding fixture (Fig. 5). Tighten hook
on engine holding fixture until all slack is removed
from all 4 pieces of webbing material.

Fig. 6 Front Engine Support Attaching Locations 3.3

Ltr.

of the correct thread size and length, install webbing
hook on bolt. Then install bolt into threaded hole on
back of cylinder heads and tighten bolt.

(5) Securely attach pieces of webbing material to
hook on engine holding fixture (Fig. 7). Tighten hook
on engine holding fixture until all slack is remove
from all 4 pieces of webbing material.

Fig. 5 Engine Supporting Fixture Installed 3.3 Ltr.

3.5 LTR ENGINE

(1) Mount Fixture, Engine Support Special Tool

7137 or equivalent across engine compartment (Fig.

7). Using nylon webbing material such as seat belt
material or equivalent, mount it to the following loca­tions on the 3.5 ltr. engine.

(2) Remove bolt attaching timing belt housing to
front of engine assembly (Fig. 7 and 8). Install web­bing material hook on timing belt housing attaching
bolt, install bolt and tighten (Fig. 7 and 8).

(3) Remove generator to generator mounting
bracket attaching nut and bolt (Fig. 9). Install web­bing material hook on generator mounting bolt, re­install and tighten original nut and bolt (Fig. 9).

(4) Mount remaining pieces of webbing material to
back of right and left cylinder head using the
threaded hole on back of cylinder heads. Using a bolt

Fig. 7 Engine Supporting Fixture Installed 3.5 Ltr.

CRADLE ASSEMBLY REMOVAL ALL ENGINES

(1) Raise vehicle on jackstands or centered on a
frame contact type hoist. See Hoisting in the Lubrica­tion and Maintenance section of this manual, for the
required lifting procedure to be used for this vehicle.

(2) Remove both front wheel and tire assemblies
from the vehicle.

Fig. 8 Front Engine Support Attachment To Timing

Belt Housing

SUSPENSION AND DRIVESHAFTS 2 - 25

CAUTION: When lower control is separated from
steering knuckle, do not let ball joint seal hit up
against steering knuckle. If ball joint seal hits steer­ing knuckle, seal damage may occur. If ball joint
seal becomes torn, replace seal before assembling
lower control arm to knuckle.

(4) Carefully insert a pry bar between lower control
arm and steering knuckle (Fig. 11), to separate ball
joint stud from steering knuckle (Fig. 11). Note: Use

caution when separating ball joint stud from
steering knuckle so ball joint seal does not get
cut.

CAUTION: Pulling steering knuckle out from vehicle
after releasing from ball joint can separate inner
tripod joint. See Driveshafts.

Fig. 9 Front Engine Support Attachment To

Generator Bracket

(3) Remove left and right ball joint stud to steering

knuckle clamp nut and bolt (Fig. 10).

Fig. 10 Control Arm To Steering Knuckle

Attachment

Fig. 11 Separating Ball Joint From Steering Knuckle

(5) Remove ground strap from cradle assembly.
Ground strap is located on right side of cradle below
half shaft (Fig. 12).

Fig. 12 Ground Strap

2 - 26 SUSPENSION AND DRIVESHAFTS

(6) Remove the 4 nuts attaching motor mounts to

cradle assembly (Fig. 13).

Fig. 15 Stabilizer Bar Isolator Bushing Attachment

To Cradle

MOVE CRADLE WITHOUT USING JACK STANDS
TO SUPPORT COMPONENTS.

(9) Position a jack stand under front of cradle and
at center of transaxle to cradle assembly mount (Fig.

16). Raise jack stand at transaxle mount until tran­saxle mount just lifts off cradle assembly.

Fig. 13 Motor Mount To Cradle Assembly

Attachment

(7) Remove the 4 bolts attaching transaxle mount

to rear of cradle assembly (Fig. 14).

Fig. 14 Transmission Mount To Cradle Assembly

Mounting Bolts

(8) Remove the 2 bolts each, attaching the stabi­lizer bushing retainer and bushing to cradle assembly
(Fig. 15).

WARNING:
SUPPORT CRADLE ASSEMBLY AND TRANSAXLE
ASSEMBLY DURING CRADLE ASSEMBLY RE­MOVAL FROM VEHICLE. DO NOT ATTEMPT TO RE-

THE JACK STANDS ARE REQUIRED TO

Fig. 16 Jack Stands Supporting Cradle And

Transaxle

(10) Cradle assembly is now ready to be removed
from vehicle using the following procedure. A helper
will be required when removing cradle assembly from
vehicle.

• Loosen but do not fully remove the 2 rear cradle
assembly to body attaching bolts (Fig. 17).

• Loosen and remove the 2 front cradle assembly to
body attaching bolts (Fig. 17).

• With a helper supporting rear of cradle assembly
and the jack stand supporting transaxle. Remove the
2 rear cradle assembly to body attaching bolts (Fig.

17).

SUSPENSION AND DRIVESHAFTS 2 - 27

• Slowly lower front jack stand until weight of en­gine is supported by engine support fixture and motor
mount bolts are clear of cradle assembly. With a
helper at rear of cradle assembly, lift front of cradle
assembly off jack stand and remove from vehicle.

bushing from around stabilizer bar. The stabilizer bar
to cradle assembly bushings, should be positioned on
stabilizer bar, so slit in bushing is positioned toward
front of vehicle (Fig. 19).

Fig. 19 Isolator Bushings Installed On Stabilizer Bar

CRADLE ASSEMBLY INSTALLATION ALL ENGINES

(1) Install stabilizer bar, isolator bushings and re­tainers back in vehicle as an assembly (Fig. 18). Be
sure stabilizer bar in installed through openings in
splash shields (Fig. 18). Install the stabilizer bar link
to stabilizer bar attaching nuts. Torque stabilizer bar
link to stabilizer bar attaching nut to 95 Nzm (70 ft.
lbs.).

(2) Tie stabilizer bar up against the 2 transaxle to
engine block brackets (Fig. 20). This will keep stabi­lizer bar out of the way when installing cradle assem­bly.

Fig. 17 Cradle Assembly To Body Attaching

Locations

(11) After cradle assembly is removed from vehicle.
Remove the 2 stabilizer bar, to stabilizer bar link
attaching nuts (Fig. 18). Remove stabilizer bar assem­bly from vehicle.

Fig. 18 Stabilizer Bar Removal And Installation

STABILIZER BAR AND BUSHING INSPECTION

Inspect for broken or distorted retainers and bush­ings. If bushing replacement is required, bushing can
be removed by opening slit in bushing and removing

Fig. 20 Stabilizer Bar Stored For Cradle Installation

(3) With the aid of a helper raise cradle assembly
(Fig. 1) back up into vehicle, resting front of cradle
assembly on a jack stand. Then use following proce­dure to install cradle assembly back into vehicle.

• With the aid of a helper, raise rear of cradle assem­bly up far enough by hand to start the 2 rear cradle
assembly to body attaching bolts (Fig. 21). Install
bolts far enough to securely hold cradle assembly in
place but DO NOT TIGHTEN.

2 - 28 SUSPENSION AND DRIVESHAFTS

• Using jack stand raise front of cradle assembly up
against bottom of motor mounts. Be sure all 4 motor
mount studs come through holes in cradle assembly.

• Continue to raise cradle assembly and engine using
jack stand until the 2 front cradle assembly to body
attaching bolts (Fig. 21) can be started.

• Lower transaxle and align transaxle mount with
the 4 transaxle mount attaching holes in the cradle
assembly. Install BUT DO NOT TIGHTEN the 4 tran­saxle mount to cradle assembly attaching bolts (Fig.

14). The 2 long bolts go in the front cradle as-

sembly to transaxle mount holes.

CAUTION: Before tightening cradle assembly to
body attaching bolts. Check that all 4 cradle assem­bly to body mounting bolts are installed straight into
mounting plates in frame rails and mounting plates
are not cocked inside the frame rails.

• Using a crisscross pattern, tighten all 4 cradle
assembly to body attaching bolts (Fig. 21) until cradle
is seated up against body. Then repeating the criss­cross pattern, torque all 4 cradle assembly to body
mounting bolts to 155 Nzm (115 ft. lbs.).

Fig. 22 Transmission Mount To Cradle Assembly

Mounting Bolts

CAUTION: When stabilizer bar is installed. Position
stabilizer bar, so lower part of stabilizer bar is cen­tered in the middle of the cradle assembly. Failure to
do this may cause stabilizer bar to come in contact
with other suspension components.

(5) Untie the stabilizer bar from brackets and posi­tion it on cradle assembly. Align the stabilizer bar
bushing retainers with the mounting holes in the
cradle assembly (Fig. 15). Install but do not tighten
the 4 bushing retainer to cradle assembly mounting
bolts. The 4 retaining bolts will be torqued when
vehicle is lowered to the ground.

(6) Install the 4 motor mount to cradle assembly
attaching nuts (Fig. 13). Torque the 4 nuts to 61 Nzm
(45 ft. lbs).

(7) Install ground strap on cradle assembly (Fig.

12). Be sure ground strap to cradle screw is securely
tightened.

CAUTION: Pulling steering knuckle out from vehicle
after releasing from ball joint can separate inner C/V
joint. See Driveshafts.

Fig. 21 Cradle Assembly To Body Attaching Bolts

(4) Tighten the 4 transaxle mount to cradle assem-

bly mounting bolts (Fig. 22).

CAUTION: When ball joint stud is installed into
steering knuckle, do not let ball joint seal hit up
against steering knuckle. If ball joint seal hits steer­ing knuckle, seal damage may occur. If ball joint
seal becomes torn, replace seal before assembling
lower control arm to knuckle.

(8) Install lower ball joint studs into steering
knuckles. Install steering knuckle to lower ball joint
stud, clamp bolts and nuts into steering knuckles
(Fig. 23). Torque clamp bolt to 55 Nzm (40 ft. lbs.).

(9) Install the wheel and tire assembly.

(10) Tighten the wheel mounting stud nuts in
proper sequence (Fig. 24) until all nuts are torqued to
half specification. Then repeat the tightening se­quence to the full specified torque of 129 Nzm (95 ft.
lbs.).

(11) Lower vehicle to the ground.

Fig. 23 Control Arm To Steering Knuckle

Attachment

SUSPENSION AND DRIVESHAFTS 2 - 29

The front suspension knuckle is not a serviceable
component. Do not attempt to straighten or repair the
front suspension knuckle in any way.

Service repair or replacement of the front (drive)
hub and bearing, can be done with the front suspen­sion knuckle remaining on the vehicle.

Fig. 24 Tightening Wheel Nuts

(12) With the full weight of the vehicle supported
by the suspension. Use a long extension, and torque
the 4 stabilizer bar bushing retainer to cradle assem­bly attaching bolts to 55 Nzm (40 ft. lbs.).

(13) Remove the webbing material from the engine
and the engine support fixture from the vehicle.

(14) Position vehicle on an alignment rack and
check that the vehicles Toe is within specifications.
Adjust the vehicle Toe setting if not within specifica­tions.

STEERING KNUCKLE SERVICE

The front suspension knuckle (Fig. 1) provides for
steering control of the vehicle. Supports the brake
caliper and absorbs the loads exerted during vehicle
braking. It also supports the front (driving) hub and
bearing and stub axle assembly.

The front suspension knuckle also provides the abil­ity to align the front wheels of the vehicle. This is
done by allowing for front wheel Toe adjustment.

Fig. 1 Front Knuckle Assembly

REMOVE

(1)

Raise vehicle on jackstands or centered on a
frame contact type hoist. See Hoisting in the Lubri­cation and Maintenance section of this manual, for
the required lifting procedure to be used for this
vehicle.

(2) Remove the front wheel and tire assembly from

the vehicle.

(3) Remove the front caliper assembly from the
front steering knuckle assembly (Fig. 2). Refer to
Front Disc Brake Service in the Brake Section of this
service manual for caliper removal procedure.

(4) Remove front braking disk (rotor) from hub, by
pulling it straight off wheel mounting studs (Fig. 3).

(5)

Remove screw attaching ABS speed sensor

head to steering knuckle. Speed sensor head

should be removed from steering knuckle, to
avoid damage to speed sensor by outer C/V
joint when hub and bearing is removed.

(6) Carefully, remove sensor head from steering
knuckle. If the sensor has seized, due to corrosion,

2 - 30 SUSPENSION AND DRIVESHAFTS

Fig. 2 Disc Brake Caliper Mounting

Fig. 3 Removing Braking Disc

DO NOT USE PLIERS ON SENSOR HEAD. Use a
hammer and punch (Fig. 4) to tap edge of sensor ear,
rocking sensor side to side until free.

(7) Remove the hub and bearing to stub axle re-

taining nut (Fig. 5).

(8) Remove the 3 steering knuckle to hub and bear-

ing assembly attaching bolts (Fig. 6).

Fig. 4 Speed Sensor Head Removal (Typical)

Fig. 5 Hub And Bearing To Stub Axle Retaining Nut

CAUTION: If metal seal (Fig. 7) on hub and bearing
assembly is seized to steering knuckle and be­comes dislodged on hub and bearing assembly dur­ing bearing removal. The hub and bearing assembly
MUST not be re-used and MUST be replaced with a
new hub and bearing assembly. Also if flinger disc
(Fig. 7) becomes damaged (bent or dented) during
removal, hub and bearing assembly must be re­placed with a new hub and bearing assembly.

Fig. 6 Hub And Bearing Assembly Retaining Bolts

(9) Remove hub and bearing assembly from steer­ing knuckle. It is removed by sliding it straight out of
steering knuckle and off end of stub axle (Fig. 8). If
hub and bearing assembly will not slide out of
knuckle, insert a pry bar between hub and bearing

SUSPENSION AND DRIVESHAFTS 2 - 31

Fig. 9 Prying Hub And Bearing Assembly From

Steering Knuckle

Fig. 7 Hub And Bearing Assembly Seal

assembly and steering knuckle (Fig. 9) and gently pry
hub and bearing from knuckle. If stub shaft is frozen
to hub and bearing assembly tap end of stub shaft
with soft face hammer to free it from hub and bearing
spline.

Fig. 8 Hub And Bearing Assembly Removal And

Installation

(10) Remove the ball joint stud to steering knuckle

clamp nut and bolt (Fig. 10).

CAUTION: When lower control arm is separated
from steering knuckle, do not let ball joint seal hit
up against steering knuckle. If ball joint seal hits
steering knuckle, seal damage may occur. If ball
joint seal becomes torn, replace seal before assem­bling lower control arm to knuckle.

Fig. 10 Control Arm To Steering Knuckle

Attachment

(11) Carefully insert a pry bar between lower con­trol arm and steering knuckle (Fig. 11). Push down on
pry bar to separate ball joint stud from steering
knuckle (Fig. 11). Note: Use caution when sepa-

rating ball joint stud from steering knuckle so
ball joint seal does not get cut.

CAUTION: The strut assembly to steering knuckle
bolts are serrated were they go through strut as­sembly and steering knuckle. When removing bolts,
turn nuts off bolts DO NOT TURN BOLTS IN STEER­ING KNUCKLE. If bolts are turned damage to steer­ing knuckle will result.

(12) Remove the strut assembly to steering knuckle
attaching bolts (Fig. 12).

(13) Remove the steering knuckle from the vehicle.

INSTALL

(1) Install steering knuckle on ball joint stud. In­stall steering knuckle to lower ball joint stud, clamp

2 - 32 SUSPENSION AND DRIVESHAFTS

(2) Position steering knuckle neck into strut assem­bly.

CAUTION: The strut assembly to steering knuckle
bolts are serrated where they go through strut as­sembly and steering knuckle. When installing bolts,
turn nuts onto bolts DO NOT TURN BOLTS IN
STEERING KNUCKLE. If bolts are turned damage to
steering knuckle will result.

(3) Install the strut assembly to steering knuckle
attaching bolts (Fig. 12). Install nuts on attaching
bolts (Fig. 12). Torque the strut assembly to steering
knuckle attaching bolt nuts to 169 Nzm (125 ft. lbs.).

TURN NUTS ON BOLTS DO NOT TURN BOLTS.

Fig. 11 Separating Ball Joint From Steering Knuckle

Fig. 12 Strut Assembly To Steering Knuckle

Attaching Bolts

bolt and nut into steering knuckle (Fig. 13). Torque
clamp bolt to 55 Nzm (40 ft. lbs.).

CAUTION: Hub and bearing assembly mounting sur­faces on steering knuckle and halfshaft (Fig. 14)
must be smooth and completely free of foreign ma­terial or nicks.

Fig. 14 Hub And Bearing Assembly Mounting

Surfaces

CAUTION: When installing hub and bearing assem­bly into steering knuckle, be careful not to damage
the flinger disc (Fig. 7) on hub and bearing assem­bly. If flinger disc becomes damaged, hub and bear­ing assembly MUST not be used and MUST be re­placed with a new hub and bearing assembly.

Fig. 13 Control Arm To Steering Knuckle

Attachment

(4) Install hub and bearing assembly onto stub
shaft and into steering knuckle until squarely seated
on face of steering knuckle. (Fig. 8).

(5) Install the 3 steering knuckle to hub and bear­ing assembly attaching bolts (Fig. 15). Equally
tighten all 3 mounting bolts until hub and bearing
assembly is squarely seated against front of steering
knuckle. Then torque all 3 hub and bearing assembly
mounting bolts to 110 Nzm (80 ft.lbs.)

Fig. 15 Hub And Bearing Assembly Retaining Bolts

CAUTION: The hub and bearing assembly to stub
shaft retaining nut (Fig. 16) is a prevailing torque nut
and can not be re-used. A NEW retaining nut MUST
be used when assembled.

SUSPENSION AND DRIVESHAFTS 2 - 33

(6) Install a NEW hub and bearing assembly to

stub shaft retaining nut (Fig. 16). Tighten, but do

not torque the hub nut at this time.

Fig. 16 Hub And Bearing To Stub Axle Retaining Nut

(7) Coat speed sensor head with High Temperature
Multi-purpose E.P. Grease before installing into the
steering knuckle. Install speed sensor head into steer­ing knuckle. Install screw tighten to 7 Nzm (60 in.
lbs.).

(8) Install the braking disk back on the hub and
bearing assembly (Fig. 17).

(9) Install front brake caliper back over braking
disc and align with caliper mounting holes on steer­ing knuckle (Fig. 18). Refer to Front Disc Brake Ser­vice in the Brake Section of this service manual for
caliper installation procedure. Install the caliper to
steering knuckle attaching bolts and torque to 19 Nzm
(168 in. lbs.).

Fig. 17 Installing Braking Disc

Fig. 18 Disc Brake Caliper Mounting

(10) Install wheel and tire assembly on vehicle.
Tighten the wheel mounting stud nuts in proper se­quence (Fig. 19) until all nuts are torqued to half
specification. Then repeat the tightening sequence to
the full specified torque of 129 Nzm (95 ft. lbs.).

(11) Lower vehicle to the ground.

2 - 34 SUSPENSION AND DRIVESHAFTS

Fig. 19 Tightening Wheel Nuts

CAUTION: When torquing hub and bearing assem­bly to stub shaft retaining nut, do not exceed the
maximum torque of 176 Nzm (130 ft. lbs.). If the
maximum torque is exceeded this may result in a
failure of the drive shaft.

(12) With the vehicle brakes applied to keep vehicle
from moving. Tighten the NEW stub shaft to hub and
bearing assembly retaining nut to 163 Nzm ± 14 (120
ft. lbs. ± 10) (Fig. 20).

1994 New Yorker, LHS, Concorde, Intrepid and Vision
Publication No. 81-270-4140
TSB 02-13-94 September 23, 1994

(2) Remove the front wheel and tire assembly from

the vehicle.

(3) Remove the front caliper assembly from the
front steering knuckle assembly (Fig. 1). Refer to
Front Disc Brake Service in the Brake Section of this
service manual for caliper removal procedure.

Fig. 1 Disc Brake Caliper Mounting

(4) Remove front braking disk (rotor) from hub, by
pulling it straight off wheel mounting studs (Fig. 2).

Fig. 20 Tighten Hub And Bearing Retaining Nut

HUB AND BEARING ASSEMBLY

This unit is serviced only as a complete assembly. It
is mounted to the steering knuckle by 3 mounting
bolts that are removed from the rear of the steering
knuckle.

REMOVAL

(1) Raise vehicle on jackstands or centered on a
frame contact type hoist. See Hoisting in the Lubrica­tion and Maintenance section of this manual, for the
required lifting procedure to be used for this vehicle.

Fig. 2 Removing Braking Disc

(5) Remove the hub and bearing to stub axle re-

taining nut (Fig. 3).

(6) Remove the 3 steering knuckle to hub and bear-

ing assembly attaching bolts (Fig. 4).

Fig. 3 Hub And Bearing To Stub Axle Retaining Nut

SUSPENSION AND DRIVESHAFTS 2 - 35

Fig. 4 Hub And Bearing Assembly Retaining Bolts

CAUTION: If metal seal (Fig. 5) on hub and bearing
assembly is seized to steering knuckle and be­comes dislodged on hub and bearing assembly dur­ing bearing removal. The hub and bearing assembly
MUST not be reused and MUST be replaced with a
new hub and bearing assembly.

CAUTION: When removing hub and bearing assem­bly from steering knuckle, be careful not to damage
the flinger disc (Fig. 5) on hub and bearing assem­bly. If flinger disc becomes damaged, hub and bear­ing assembly MUST not be used and MUST be re­placed with a new hub and bearing assembly.

(7) Remove hub and bearing assembly from steer­ing knuckle, by sliding it straight out of steering
knuckle and off end of stub axle (Fig. 6). If hub and
bearing assembly will not slide out of knuckle. Insert
a pry bar between hub and bearing assembly and
steering knuckle (Fig. 7) and gently pry hub and
bearing from knuckle. If stub shaft is frozen to hub

Fig. 5 Hub And Bearing Assembly Seal

and bearing assembly tap end of stub shaft with soft
face hammer to free it from hub and bearing spline.

Fig. 6 Hub And Bearing Assembly Removal And

Installation

INSTALLATION

CAUTION: Hub and bearing assembly mounting sur­faces on steering knuckle and halfshaft (Fig. 8) must
be smooth and completely free of foreign material or
nicks.

CAUTION: When installing hub and bearing assem­bly into steering knuckle, be careful not to damage
the flinger disc (Fig. 5) on hub and bearing assem­bly. If flinger disc becomes damaged, hub and bear­ing assembly MUST not be used and MUST be re­placed with a new hub and bearing assembly.

2 - 36 SUSPENSION AND DRIVESHAFTS

Fig. 7 Prying Hub And Bearing Assembly From

Steering Knuckle

Fig. 8 Hub And Bearing Assembly Mounting

Surfaces

(1) Install hub and bearing assembly onto stub
shaft and into steering knuckle until squarely seated
on face of steering knuckle. (Fig. 6).

(2) Install the 3 hub and bearing assembly to steer­ing knuckle attaching bolts (Fig. 9). Equally tighten
all 3 mounting bolts until hub and bearing assembly
is squarely seated against front of steering knuckle.
Then torque all 3 hub and bearing assembly mount­ing bolts to 110 Nzm (80 ft.lbs.)

Fig. 9 Hub And Bearing Assembly Retaining Bolts

Fig. 10 Hub And Bearing To Stub Axle Retaining Nut

CAUTION: The hub and bearing assembly to stub
shaft retaining nut (Fig. 10) is a prevailing torque nut
and can not be re-used. A NEW retaining nut MUST
be used when assembled.

(3) Install a NEW hub and bearing assembly to
stub shaft retaining nut (Fig. 10). Tighten, but do

not torque the hub nut at this time.

(4) Install the braking disk back on the hub and
bearing assembly (Fig. 11).

Fig. 11 Installing Braking Disc

(5) Install front brake caliper back over braking
disc and align with caliper mounting holes on steer­ing knuckle (Fig. 12). Refer to Front Disc Brake Ser­vice in the Brake Section of this service manual for
caliper installation procedure. Install the caliper
adapter to steering knuckle attaching bolts and
torque to 19 Nzm (168 in. lbs.).

1994 New Yorker, LHS, Concorde, Intrepid and Vision

SUSPENSION AND DRIVESHAFTS 2 - 37

Publication No. 81-270-4140
TSB 02-13-94 September 23, 1994

maximum torque of 176 Nzm (130 ft. lbs.). If the
maximum torque is exceeded this may result in a
failure of the drive shaft.

(8) With the vehicle brakes applied to keep vehicle
from moving. Torque the NEW stub shaft to hub and
bearing assembly retaining nut to 163 Nzm ± 14 (120
ft. lbs. ± 10) (Fig. 14).

Fig. 12 Disc Brake Caliper Mounting

(6) Install wheel and tire assembly on vehicle.

Tighten the wheel mounting stud nuts in proper se-

quence (Fig. 13) until all nuts are torqued to half
specification. Then repeat the tightening sequence to
the full specified torque of 129 Nzm (95 ft. lbs.).

Fig. 13 Tightening Wheel Nuts

(7) Lower vehicle to the ground.

CAUTION: When torquing hub and bearing assem­bly to stub shaft retaining nut, do not exceed the

Fig. 14 Tighten Hub And Bearing Retaining Nut

(9) Check the Toe setting on the vehicle and reset if
not with in specifications.

SERVICING WHEEL STUDS

The L.H. platform vehicles use a one piece, lubri­cated for life hub and bearing assembly.

CAUTION: If wheel attaching stud needs to be re­placed in the hub and bearing assembly the studs
CAN NOT be hammered out of the hub flange. If a
stud is removed by hammering it out of the bearing
flange, damage to the hub and bearing assembly
will occur leading to premature bearing failure.

The following procedure and special tools shown
MUST be used when replacing wheel attaching
studs.

The hub and bearing assembly does not require
removal from the steering knuckle to replace wheel
attaching studs in the hub and bearing assembly.

REMOVE

(1)

Raise vehicle on jackstands or centered on a
frame contact type hoist. See Hoisting in the Lubri­cation and Maintenance section of this manual, for
the required lifting procedure to be used for this
vehicle.

(2) Remove the front wheel and tire assembly from

the vehicle.

(3) Remove the front caliper assembly from the

front steering knuckle assembly (Fig. 1). Refer to

2 - 38 SUSPENSION AND DRIVESHAFTS

Front Disc Brake Service in the Brake Section of this
service manual for caliper removal procedure.

Fig. 1 Disc Brake Caliper Mounting

(4) Remove front braking disk (rotor) from hub, by

pulling it straight off wheel mounting studs (Fig. 2).

Fig. 3 Removing Wheel Stud From Hub And Bearing

INSTALL

(1) Install replacement wheel stud into flange of
hub and bearing assembly. Install washers on wheel
stud, then install a wheel lug nut on stud with flat
side of lug nut against washers (Fig. 4).

Fig. 2 Removing Braking Disc

(5) Install a lug nut on the wheel stud to be re­moved from the hub and bearing assembly (Fig. 3) so
the threads on stud are even with end of lug nut.
Install Remover, Special Tool C-4150 on hub and
bearing assembly flange and wheel stud (Fig. 3).

(6) Tighten down on special tool, pushing wheel
stud out of the hub and bearing assembly flange.
When shoulder of wheel stud is past flange remove
special tool from hub and bearing assembly. Remove
lug nut from stud and remove wheel stud from flange.

Fig. 4 Installing Wheel Stud Into Hub And Bearing

(2) Tighten the wheel lug nut, pulling the wheel
stud into the flange of the hub and bearing assembly.
When the head of the stud is fully seated against the
bearing flange, remove lug nut and washers from
wheel stud.

(3) Install the braking disk back on the hub and

bearing assembly (Fig. 5).

SUSPENSION AND DRIVESHAFTS 2 - 39

Fig. 5 Installing Braking Disc

(4) Install front brake caliper back over braking
disc and align with caliper mounting holes on steer­ing knuckle (Fig. 6). Refer to Front Disc Brake Ser­vice in the Brake Section of this service manual for
caliper installation procedure. Install the caliper
adapter to steering knuckle attaching bolts and
torque to 19 Nzm (168 in. lbs.).

(5) Install wheel and tire assembly on vehicle.
Tighten the wheel mounting stud nuts in proper se­quence (Fig. 7) until all nuts are torqued to half
specification. Then repeat the tightening sequence to
the full specified torque of 129 Nzm (95 ft. lbs.).

(6) Lower vehicle to the ground.

Fig. 6 Disc Brake Caliper Mounting

Fig. 7 Tightening Wheel Nuts

2 - 40 SUSPENSION AND DRIVESHAFTS

DRIVESHAFTS

INDEX

page page

Driveshaft Reconditioning Procedure ..........46

General Information ....................... 40

Inner Tripod Joint Seal Boot ................. 46

GENERAL INFORMATION

All L.H. platform vehicles are equipped with an un­equal length drive shaft system (Fig. 1). The left side of
the vehicle is equipped with a longer drive shaft than
the right side of the vehicle. The L.H. platform uses solid
interconnecting shafts on both sides of the vehicle.

The driveshaft assemblies are three piece units.
Each driveshaft has a Tripod Joint, an Interconnect­ing Shaft and a outer C/V joint. The Tripod Joint is
splined onto the transaxle stub shaft, and the outer
C/V joint has a stub shaft that is splined into the
front wheel hub and bearing assembly.

Outer C/V Joint Sealing Boot Service .......... 50

Service Procedures ....................... 42

Servicing Driveshafts ...................... 42

The inner tripod joint boots, on the L.H. plat­form vehicle are of different materials. The left
inner boot is made of high temperature applica­tion silicone, and the right inner boot is made of
hytrel plastic. When drive shaft boots are re­placed be sure boots of the correct material are
used on the correct side of the vehicle.

The driveshafts used on the L.H. platform vehicles
are supplied by Saginaw Division for all available
drivelines.

Fig. 1 L.H. Platform Driveshafts (Halfshafts)

SUSPENSION AND DRIVESHAFTS 2 - 41

SUSPENSION/STEERING/DIAGNOSIS FRONT WHEEL DRIVE

2 - 42 SUSPENSION AND DRIVESHAFTS

SERVICE PROCEDURES

Procedures for removal and installation of drive­shafts on the L.H. platform vehicles are different and
somewhat easier, then those on other front wheel
drive vehicles. This new drive shaft design, allows
both drive shafts to be removed from the vehicle
without dismantling the transaxle.

CAUTION: Boot sealing is vital to retain special lubri­cants and to prevent foreign contaminants from enter­ing the C/V joint. Mishandling, such as allowing the
assemblies to dangle unsupported, pulling or pushing
the ends can cut boots or damage C/V joints. The L.H.
platform driveshafts use no retention system to retain
the spider assembly in the tripod housing. During re­moval and installation procedures always support both
ends of the driveshaft to prevent damage or disengag­ing tripod joint. Therefore, do not pull on the intercon­necting shaft when attempting to remove drive shafts
from vehicle.

SERVICING DRIVESHAFTS

REMOVE

(1) Raise vehicle on jackstands or centered on a
frame contact type hoist. See Hoisting in the Lubrica­tion and Maintenance section of this manual, for the
required lifting procedure to be used for this vehicle.

(2) Remove the front wheel and tire assembly from
the vehicle.

(3) Remove the front caliper assembly from the
front steering knuckle assembly (Fig. 1). Refer to
Front Disc Brake Service in the Brake Section of this

service manual for caliper removal procedure.

Fig. 2 Removing Braking Disc

Fig. 3 Speed Sensor Cable Routing Bracket

Fig. 1 Disc Brake Caliper Mounting

(4) Remove front braking disk (rotor) from hub, by
pulling it straight off wheel mounting studs (Fig. 2).

(5) Remove the speed sensor cable routing bracket
from the strut assembly (Fig. 3).

(6) Remove the hub and bearing to stub axle re­taining nut (Fig. 4).

Fig. 4 Hub And Bearing To Stub Axle Retaining Nut

SUSPENSION AND DRIVESHAFTS 2 - 43

(7) Dislodge inner tripod joint from stub shaft re­taining snap ring on transaxle assembly (Fig. 5). In­ner tripod joint is dislodged from stub shaft retaining
snap ring, by inserting a pry bar between transaxle
case and inner tripod joint and prying on tripod joint.

Only disengage the inner tripod joint from the
retaining snap ring. Do not attempt to remove
the inner tripod joint from the transmission
stub shaft at this time.

CAUTION: When removing outer C/V joint from hub
and bearing assembly, do not allow the flinger disk
(Fig. 7) on hub and bearing assembly to become
damaged. Damage to the flinger disk will cause dirt
and water intrusion into bearing and premature
bearing failure.

(10) Hold outer C/V joint assembly with one hand.
Grasp steering knuckle with other and rotate it out
and to the rear of the vehicle, until outer C/V joint
clears hub and bearing assembly (Fig. 7).

Fig. 5 Inner Tripod Joint Removal From Stub Shaft

CAUTION: The strut assembly to steering knuckle
bolts are serrated were they go through strut as­sembly and steering knuckle. When removing bolts,
turn nuts off bolts DO NOT TURN BOLTS IN STEER­ING KNUCKLE. If bolts are turned damage to steer­ing knuckle will result.

(8) Remove the strut assembly to steering knuckle

attaching bolts (Fig. 6).

Fig. 6 Strut Assembly To Steering Knuckle

Attaching Bolts

(9) Remove the top of the steering knuckle from the

strut assembly.

Fig. 7 Outer C/V Joint Removal From Hub and

Bearing

(11) Remove drive shaft inner tripod joint from
transaxle stub shaft. When removing drive shaft,

do not pull on interconnecting shaft to remove
inner tripod joint from stub shaft. Removal in
this manner will separate the spider assembly
from the tripod joint housing. Grasp inner tri­pod joint (Fig. 8) and interconnecting shaft and
pull on both pieces at the same time.

INSTALL

CAUTION: The inboard tripod joint retaining circlip
and O-Ring seal (Fig. 9) on the transaxle stub shaft
are not re-usable. Whenever the inboard tripod joint
is removed from the stub shaft, the retaining circlip
and O-Ring seal MUST BE REPLACED. The retaining
circlip and O-Ring seal is included in all service kits
requiring removal of the inboard tripod joint from
the stub shaft.

(1) Replace O-Ring seal and tripod joint retaining
circlip (Fig. 9) on the transaxle stub shaft.

2 - 44 SUSPENSION AND DRIVESHAFTS

Fig. 8 Inner Tripod Joint Removal From Stub Shaft

Fig. 9 Tripod Joint Retaining Circlip And O-Ring

Seal

(2) Evenly apply a bead of grease, such as Mopar
Multi-Purpose Lubricant or an equivalent, around
spline of inner tripod joint (Fig. 10), where the O-Ring
seats against tripod joint. This will spread grease
onto stub shaft during tripod joint installation pre­venting corrosion and help to seal the O-ring.

(3) Install drive shaft through hole in splash shield.
Grasp inner tripod joint in one hand and intercon­necting shaft in the other. Align inner tripod joint
spline with stub shaft spline on transaxle (Fig. 11).
Use a rocking motion with the inner tripod joint, to
get it past the circlip on the transaxle stub shaft.

(4) Continue pushing tripod joint onto transaxle
stub shaft until it stops moving. The O-Ring seal on
the stub should not be visible when inner tripod joint
is fully installed on stub shaft. To check that inner

tripod joint retaining circlip is locked into tri­pod joint, grasp inner tripod joint and pull on it
by hand. If circlip is locked into tripod joint,
tripod joint will not move on stub shaft.

Fig. 10 Grease Applied To Inner Tripod Joint

Housing Spline

Fig. 11 Inner Tripod Joint Installation On Stub Shaft

CAUTION: When installing outer C/V joint into the
hub and bearing assembly, do not allow the flinger
disk (Fig. 12) on hub and bearing assembly to be­come damaged. Damage to the flinger disk can
cause dirt and water intrusion into bearing and pre­mature bearing failure.

(5) Hold outer C/V joint assembly with one hand.
Grasp steering knuckle with other hand and rotate it
out and to the rear of the vehicle. Install outer C/V
joint into the hub and bearing assembly (Fig. 12).

(6) Install the top of the steering knuckle into the
strut assembly. Align the steering knuckle to strut
assembly mounting holes.

CAUTION: The strut assembly to steering knuckle
bolts are serrated where they go through strut as­sembly and steering knuckle. When installing bolts,
turn nuts onto bolts DO NOT TURN BOLTS IN
STEERING KNUCKLE. If bolts are turned damage to
steering knuckle will result.

Fig. 12 Outer C/V Joint Installation Into Hub and

Bearing

(7) Install the strut assembly to steering knuckle
attaching bolts (Fig. 13). Install nuts on attaching
bolts (Fig. 13). Torque the strut assembly to steering
knuckle attaching bolt nuts to 169 Nzm (125 ft. lbs.).

TURN NUTS ON BOLTS DO NOT TURN BOLTS.

SUSPENSION AND DRIVESHAFTS 2 - 45

Fig. 14 Hub And Bearing To Stub Axle Retaining Nut

(9) Install speed sensor cable routing bracket on
front strut assembly. Then install and securely
tighten routing bracket attaching screw (Fig. 3).

(10) Install the braking disk back on the hub and
bearing assembly (Fig. 15).

Fig. 13 Strut Assembly To Steering Knuckle

Attaching Bolts

CAUTION: The hub and bearing assembly to stub
shaft retaining nut (Fig. 14) is a prevailing torque nut
and can not be re-used. A NEW retaining nut MUST
be used when assembled.

(8) Install a NEW hub and bearing assembly to

stub shaft retaining nut (Fig. 14). Tighten but do

not torque the hub nut at this time.

Fig. 15 Installing Braking Disc

(11) Install front brake caliper back over braking
disc and align with caliper mounting holes on steer­ing knuckle (Fig. 16). Refer to Front Disc Brake Ser­vice in the Brake Section of this service manual for
caliper installation procedure. Install the caliper to
steering knuckle attaching bolts and torque to 19 Nzm
(168 in. lbs.).

(12) Install wheel and tire assembly on vehicle.
Tighten the wheel mounting stud nuts in proper se­quence (Fig. 17) until all nuts are torqued to half

2 - 46 SUSPENSION AND DRIVESHAFTS

Fig. 16 Disc Brake Caliper Mounting

specification. Then repeat the tightening sequence to
the full specified torque of 129 Nzm (95 ft. lbs.).

1994 New Yorker, LHS, Concorde, Intrepid and Vision
Publication No. 81-270-4140
TSB 02-13-94 September 23, 1994

Fig. 18 Tighten Hub And Bearing Retaining Nut

DRIVESHAFT RECONDITIONING PROCEDURE

The only service which is to be performed on
the driveshaft assemblies is the replacement of
the drive shaft seal boots.

If any failure of internal driveshaft components is
diagnosed during a vehicle road test or disassembly of
the drive shaft, the drive shaft will need to be re­placed as an assembly.

Note: that lubricant requirements and quanti­ties are different for Inner Joints than for Outer
Joints. Use only the recommended lubricants.

See (Fig. 1) for the exploded view of the front drive
shaft components and there location in the assembly.

Fig. 17 Tightening Wheel Nuts

(13) Lower vehicle to the ground.

CAUTION: When torquing hub and bearing assem­bly to stub shaft retaining nut, do not exceed the
maximum torque of 176 Nzm (130 ft. lbs.). If the
maximum torque is exceeded this may result in a
failure of the drive shaft.

(14) With the vehicle brakes applied to keep vehicle
from moving. Torque the NEW stub shaft to hub and
bearing assembly retaining nut to 163 Nzm ± 14 (120
ft. lbs. ± 10) (Fig. 18).

INNER TRIPOD JOINT SEAL BOOT

REMOVE

To remove sealing boots from driveshafts for re­placement, the drive shaft assemblies must be re­moved from the vehicle. See Servicing Driveshaft in
this section of the service manual for the required
drive shaft removal and replacement procedure.

The Saginaw inner tripod joints used on the L.H.
platform vehicles use no internal retention in the
tripod housing to keep the spider assembly in the
housing. Therefore do not pull on the interconnecting
shaft to disengage tripod housing from transmission
stub shaft. Removal in this manner will cause dam­age to inboard boots.

(1) Remove the driveshaft requiring boot replace­ment from the vehicle. See Servicing Driveshaft in
this section of the service manual for the required
drive shaft removal procedure.

Remove large boot clamp which retains inner

(2)
tripod joint sealing boot to tripod joint housing (Fig.

2) and discard. Then remove small clamp which re­tains inner tripod joint sealing boot to interconnect-

SUSPENSION AND DRIVESHAFTS 2 - 47

Fig. 1 L.H. Platform Driveshaft Components

2 - 48 SUSPENSION AND DRIVESHAFTS

ing shaft (Fig. 2) and discard. Remove the sealing
boot from the tripod housing and slide it down the
interconnecting shaft.

Fig. 2 Inner Tripod Joint Sealing Boot Clamps

CAUTION: When removing the spider joint from the
tripod joint housing. Hold the rollers in place on the
spider trunions to prevent the rollers and needle
bearings from falling away.

Fig. 4 Spider Assembly Retaining Snap Ring

Removal

(6) Thoroughly clean and inspect spider assembly,
tripod joint housing and interconnecting shaft for any
signs of excessive wear. If any parts show signs of

excessive wear, the driveshaft assembly will re­quire replacement. Component parts of the L.H.
platform driveshaft assemblies are not service­able.

(3) Slide the interconnecting shaft and spider as-

sembly out of the tripod joint housing (Fig. 3).

Fig. 3 Spider Assembly Joint Removal From

Housing

(4) Remove snap ring which retains spider assem­bly to interconnecting shaft (Fig. 4). Then remove the
spider assembly from interconnecting shaft. If spider
assembly will not come off interconnecting shaft by
hand, it can be removed by tapping the end of the
spider body with a brass drift. Do not hit the outer

tripod bearings in an attempt to remove spider
assembly from interconnecting shaft.

(5) Slide failed sealing boot off the interconnecting
shaft.

INSTALL

The inner tripod joint sealing boots used on
the L.H. platform vehicles are made from 2 dif­ferent types of material. High temperature ap­plications use silicone rubber where as stan­dard temperature applications use hytrel
plastic. The silicone sealing boots are soft and
pliable. The Hytrel sealing boots are stiff and
rigid. The replacement sealing boot MUST BE
the same type of material as the sealing boot
which was removed.

(1) Slide inner tripod joint seal boot retaining
clamp, onto interconnecting shaft. Then slide replace­ment inner tripod joint sealing boot onto the intercon­necting shaft. Inner tripod joint seal boot MUST

be positioned on interconnecting shaft, so only
the thinnest (sight) groove on interconnecting
shaft is visible (Fig. 5).

(2) Install the spider assembly onto the intercon­necting shaft. Spider assembly must be installed on
interconnecting shaft far enough to fully install the
retaining snap ring. If spider assembly will not fully
install on interconnecting shaft by hand, it can be
installed by tapping the spider body with a brass
drift. Do not hit the outer tripod bearings in an

attempt to install spider assembly on intercon­necting shaft.

(3) Install the spider assembly to interconnecting
shaft retaining snap ring into groove on end of inter­connecting shaft (Fig. 6). Be sure the snap ring is
fully seated into groove on interconnecting shaft.

SUSPENSION AND DRIVESHAFTS 2 - 49

Fig. 5 Seal Boot Correctly Positioned On

Interconnecting Shaft

Fig. 6 Spider Assembly Retaining Snap Ring

Installation

(4) Distribute 1/2 the amount of grease provided in
the seal boot service package (DO NOT USE ANY
OTHER TYPE OF GREASE) into tripod housing. Put
the remaining amount into the sealing boot.

(5) Slide the spider assembly and the interconnect­ing shaft into the tripod joint housing (Fig. 7).

(6) Install inner tripod joint seal boot to intercon­necting shaft clamp evenly on sealing boot.

(7) Clamp sealing boot onto interconnecting shaft
using Crimper, Special Tool C-4975 and the following
procedure. Place crimping tool C-4975 over bridge of
clamp (Fig. 8). Tighten nut on crimping tool C-4975
until jaws on tool are closed completely together, face
to face (Fig. 9).

Fig. 7 Spider Assembly Installed In Housing

Fig. 8 Crimping Tool Installed On Sealing Boot

Clamp

CAUTION: Seal must not be dimpled, stretched or
out of shape in any way. If seal is NOT shaped
correctly, equalize pressure in seal and shape it by
hand.

Fig. 9 Sealing Boot Retaining Clamp Installed

2 - 50 SUSPENSION AND DRIVESHAFTS

(8) Position the sealing boot into the tripod housing
retaining groove (Fig. 10). Install seal boot retaining
clamp evenly on sealing boot.

Fig. 10 Boot and Clamp Positioning

(9) Before crimping sealing boot to tripod housing
clamp, the inner tripod joint must be at the cor-
rect stroke positioned (Fig. 11). This procedure is
required to ensure that the proper amount of air is
inside sealing boot before clamp is crimped. Failure

to perform this operation will result in inner
tripod sealing boot failure.

Fig. 11 Proper Inner Tripod Joint Stroke Position

OUTER C/V JOINT SEALING BOOT SERVICE

REMOVE

To remove outer C/V joint sealing boot from a drive­shaft for replacement, the drive shaft assembly must
be removed from the vehicle. See Servicing Driveshaft
in this section of the service manual for the required
drive shaft removal and replacement procedure.

(1) Remove driveshaft assembly requiring boot re­placement from vehicle. See Servicing Driveshaft in
this section of the service manual for the required
driveshaft removal procedure.

(2) Remove large boot clamp, retaining C/V joint
sealing boot, to C/V joint housing (Fig. 1) and discard.
Remove small clamp which retains outer C/V joint
sealing boot to interconnecting shaft and discard. Re­move sealing boot from outer C/V joint housing and
slide it down interconnecting shaft.

(10) Clamp sealing boot onto tripod housing using
Crimper, Special Tool C-4975 and the following proce­dure. Place crimping tool C-4975 over bridge of clamp
(Fig. 8). Tighten nut on crimping tool C-4975 until
jaws on tool are closed completely together, face to
face (Fig. 9).

(11) Install the driveshaft requiring boot replace­ment back into the vehicle. See Servicing Driveshaft
in this section of the service manual for the required
drive shaft installation procedure.

Fig. 1 Outer C/V Joint Seal Boot Clamps

(3) Wipe away grease to expose outer C/V joint to
interconnecting shaft retaining ring (Fig. 2). Spread
ears apart on C/V joint assembly to interconnecting
shaft retaining snap ring (Fig. 2). Slide outer C/V
joint assembly off end of interconnecting shaft.

(4) Slide failed sealing boot off interconnecting
shaft.

(5) Thoroughly clean and inspect outer C/V joint
assembly and interconnecting joint for any signs of
excessive wear. If any parts show signs of exces-

sive wear, the driveshaft assembly will require
replacement. Component parts of the L.H. plat­form driveshaft assemblies are not serviceable.

INSTALL

(1) Slide a new seal boot to interconnecting shaft
retaining clamp, onto the interconnecting shaft. Then
slide the replacement outer C/V joint assembly seal­ing boot onto the interconnecting shaft.

(2) Install outer C/V joint assembly onto intercon­necting shaft. Joint is installed on interconnecting

SUSPENSION AND DRIVESHAFTS 2 - 51

Fig. 2 Outer C/V Joint Removal From

Interconnecting Shaft

shaft, by pushing interconnecting shaft into outer
C/V joint, until retaining snap ring is seated in
groove on interconnecting shaft (Fig. 3). Be sure the
snap ring is fully seated into groove on interconnect­ing shaft.

Fig. 3 Outer C/V Joint Installed On Interconnecting

Shaft

(3) Distribute 1/2 the amount of grease provided in
seal boot service package (DO NOT USE ANY
OTHER TYPE OF GREASE) into outer C/V joint
assembly housing. Put the remaining amount into the
sealing boot.

(4) Install outer C/V joint seal boot retaining
clamp, onto interconnecting shaft. Then install re­placement outer C/V joint sealing boot onto intercon­necting shaft. Outer C/V joint seal boot MUST be

positioned on interconnecting shaft, so only the
thinnest (sight) groove on interconnecting shaft
is visible (Fig. 4).

(5) Clamp sealing boot on interconnecting shaft us­ing Crimper, Special Tool C-4975 and the following
procedure. Place crimping tool C-4975 over bridge of

Fig. 4 Seal Boot Correctly Positioned On

Interconnecting Shaft

clamp (Fig. 5). Then tighten nut on crimping tool
C-4975 until jaws on tool are closed completely to­gether, face to face (Fig. 6).

Fig. 5 Crimping Tool Installed On Sealing Boot

Clamp

Fig. 6 Sealing Boot Retaining Clamp Installed

2 - 52 SUSPENSION AND DRIVESHAFTS

CAUTION: Seal must not be dimpled, stretched or
out of shape in any way. If seal is NOT shaped
correctly, equalize pressure in seal and shape it by
hand.

(6) Position outer C/V joint seal boot, into boot re­taining groove on outer C/V joint housing (Fig. 7).
Then install seal boot to outer C/V joint retaining
clamp evenly on sealing boot.

Fig. 8 Crimping Tool Installed On Sealing Boot

Clamp

Fig. 7 Boot and Clamp Positioning

(7) Clamp sealing boot onto outer C/V joint housing
using Crimper, Special Tool C-4975 and the following
procedure. Place crimping tool C-4975 over bridge of
clamp (Fig. 8). Tighten nut on crimping tool C-4975
until jaws on tool are closed completely together, face
to face (Fig. 9).

(8) Install the driveshaft requiring boot replace­ment back on the vehicle. See Servicing Driveshaft in
this section of the service manual for the required

drive shaft installation procedure.

Fig. 9 Sealing Boot Retaining Clamp Installed

SUSPENSION AND DRIVESHAFTS 2 - 53

REAR SUSPENSION

INDEX

page page

General Information ....................... 53

Rear Crossmember ....................... 66

Rear Spindle ............................ 61

Rear Stabilizer Bar ........................ 68

GENERAL INFORMATION

The rear suspension used on the L.H. platform is a
fully independent rear suspension. The suspension
utilizes a MacPherson strut assembly at each rear
wheel of the vehicle.

CAUTION: Only frame contact hoisting equipment
can be used on L.H. platform vehicles. The L.H.
platform vehicles have a fully independent rear sus­pension. The L.H. platform vehicles can not be
hoisted using equipment designed to lift a vehicle
by the rear axle. If this type of hoisting equipment is
used damage to rear suspension components will
occur.

A forged rear spindle bolts to each rear strut as­sembly. The movement of the rear spindle is con­trolled laterally using lateral links going from the
front and rear of the spindle to the rear cross mem­ber. Fore and aft movement of the spindle is con­trolled by a trailing arm.

Rear Wheel Toe Setting Procedure ............ 55

Servicing Lateral Links ..................... 69

Servicing Rear Struts ...................... 55

Suspension Coil Springs ...................61

The lateral links and trailing arm have rubber iso­lator bushings at each end. The lateral links are
attached to the rear crossmember and spindle, using
a common bolt and nut assembly at each end. The
trailing arm bolts to the bottom of the spindle and to
a bracket attached to the floor pan of the vehicle.

Lateral links, trailing arms and spindles are nor­mally replaced only when the part has been damaged
or when the vehicle has been involved in an accident.
If a suspension part has been damaged, be sure to
check the underbody dimensions of the car. If the
underbody dimensions are not correct, the frame of
the vehicle must be straightened, before replacement
suspension components are installed.

Note: If a rear suspension component becomes
bent, damaged or fails, no attempt should be
made to straighten or repair it. Always replace
with a new component.

2 - 54 SUSPENSION AND DRIVESHAFTS

Fig. 1 L.H. Platform Fully Independent Rear Suspension

REAR WHEEL TOE SETTING PROCEDURE

Rear Wheel alignment adjustments can only
be made for the Toe In setting on the L.H. plat­form vehicles.

Toe is measured in degrees or inches and is the

distance the front edges of the tires are closer (or
farther apart) than the rear edges. See Front Wheel
Drive Specifications for Toe settings.

REAR WHEEL TOE ADJUSTMENT

(1) Prepare vehicle as described in the Pre­Alignment procedure.

(2) Loosen lateral link, adjustment link jamnuts
(Fig. 1). Rotate adjustment links as required to set
rear wheel Toe to specifications. Do not exceed the

maximum length dimensions of the lateral links
shown in (Fig. 2). Both dimensions must be
checked to ensure they do not exceed maxi­mums allowed.

SUSPENSION AND DRIVESHAFTS 2 - 55

Fig. 2 Lateral Link Maximum Length Dimensions

(2) Remove the rear wheel and tire assembly from

the vehicle.

(3) If vehicle is equipped with rear disc brakes,
remove the rear caliper assembly from the adapter.
Refer to Rear Disk Brakes in Group 5 Brakes of this
Service manual for required caliper removal proce­dure. After removing caliper assembly store caliper by
hanging it from vehicle (Fig. 1). Do not let rear cali­per assembly hang from flexible brake hose. If vehicle
is equipped with rear drum brakes, remove the brake
flex hose bracket from the support plate and wheel
cylinder (Fig. 2).

Fig. 1 Rear Wheel Toe Adjustment At Lateral Links

CAUTION:
The maximum lengths of the adjustable lateral link
at the locations shown in (Fig. 2) must not be
exceeded. If these maximum lengths are exceeded,
inadequate retention of adjustment link to the inner
and outer link may result. Ensure that the adjust­ment sleeve jam nuts are torqued to the required
specifications when the Toe setting procedure is
completed.

(3) Tighten lateral link, adjustment link locknuts to

65 Nzm (48 ft.lbs.) torque.

SERVICING REAR STRUTS

REMOVAL

(1) Raise vehicle on jackstands or centered on a
frame contact type hoist. See Hoisting in the Lubrica­tion and Maintenance section of this manual, for the
required lifting procedure to be used for this vehicle.

When setting rear (Toe In( on vehicle.

Fig. 1 Storing Rear Caliper Assembly

(4) If vehicle is equipped with rear disc brakes,

remove rear braking disc from hub.

(5) If vehicle is equipped with rear disc brakes.
Remove the speed sensor cable routing tube on trail­ing arm and the routing bracket on the trailing arm
bracket to spindle (Fig. 3). If spindle and trailing

arm assembly is lowered from strut with the

2 - 56 SUSPENSION AND DRIVESHAFTS

Fig. 2 Brake Hose Bracket And Tube

speed sensor cable attached damage to speed
sensor cable may occur.

taching link stud nut, at the stabilizer bar (Fig. 5).
The attaching link does not have to be removed from
strut assembly.

Fig. 5 Attachment Link To Stabilizer Bar Attaching

(8) Loosen and fully remove, the rear spindle to
strut assembly pinch bolt (Fig. 6).

Fig. 3 Speed Sensor Routing Tube And Bracket

(6) Remove the bolt (Fig. 4) attaching the lateral

links to the rear spindle assembly.

Fig. 4 Lateral Links To Spindle Attaching Bolt

(7) Install a thin open end wrench, on hex of at­taching link stud to keep stud from spinning in link.
Remove the rear strut assembly to stabilizer bar at-

Fig. 6 Spindle To Strut Assembly Pinch Bolt

CAUTION: When inserting center punch into rear
spindle, use care so point of center punch does not
puncture strut assembly.

(9) Insert a center punch into the hole on the
spindle (Fig. 7). Center punch must be tapped into
spindle until jammed into hole. This will spread
spindle casting allowing it to be removed from strut
assembly.

(10) Using a hammer, tap on top surface of spindle
driving it down and off the end of the strut assembly
(Fig. 8).

(11) Let the rear spindle and assembled compo­nents hang from trailing arm (Fig. 9) while strut
assembly is out of the vehicle.

(12) Lower vehicle.

Fig. 7 Center Punch Installed In Spindle

SUSPENSION AND DRIVESHAFTS 2 - 57

Fig. 8 Removing Spindle From Strut Assembly

NOTE: When removing rear strut assembly
from vehicle, access for the 3 rear strut assem­bly to strut tower attaching nuts is through the
trunk of the vehicle. See (Fig. 10) for access
location of the strut assembly attaching nuts in
trunk of vehicle.

(13) Remove the 3 rear strut assembly to rear strut
tower mounting nuts (Fig. 10) and then remove strut
assembly from vehicle.

INSPECTION

Inspect for evidence of fluid leakage from upper end
of reservoir. (Actual leakage will be a stream of fluid
running down and leaking off lower end). Slight seep­age is not unusual and will not effect performance.

INSTALLATION

(1) Position strut assembly back in vehicle with the
3 studs on strut mount assembly through holes in
rear strut tower of vehicle. Install the 3 strut mount
to body attaching nuts onto mount studs (Fig. 10).

Fig. 9 Spindle Assembly Removed From Strut

Fig. 10 Rear Strut Assembly To Strut Tower

Mounting Nuts

Using a crow foot and 3/8 in. torque wrench, torque
the 3 strut mount to strut tower attaching nuts to 28
Nzm (20 ft. lbs).

(2) Install spindle onto bottom of the strut assem­bly. Push and or tap spindle assembly onto strut,
until notch in spindle is tightly seated against locat­ing tap on strut assembly (Fig. 11). Then remove
center punch from hole in spindle. Install spindle to
strut assembly pinch bolt into spindle (Fig. 11).
Torque spindle to strut assembly pinch bolt to 55 Nzm
(40 ft. lbs.).

(3) Install the lateral links to spindle attaching bolt
(Fig. 12). Torque the lateral links to spindle attaching
bolt to 140 Nzm (105 ft. lbs.).

(4) Install stabilizer bar attaching link onto stabi­lizer bar (Fig. 13). Install stabilizer link to stabilizer

2 - 58 SUSPENSION AND DRIVESHAFTS

(5) Mount rear speed sensor cable routing tube to
rear trailing arm (Fig. 14). Then mount speed sensor
cable routing clip (Fig. 14) to the trailing arm to rear
spindle bracket.

Fig. 11 Spindle Mounted To Strut Assembly

Fig. 12 Lateral Links To Spindle Attaching Bolt

bar attaching nut (Fig. 13). Torque the stabilizer link
to stabilizer bar attaching nut to 95 Nzm (70 ft. lbs.).

Fig. 14 Speed Sensor Routing Tube And Bracket

(6) If vehicle is equipped with rear disc brakes,
install rear braking disc on hub. Carefully install rear
brake caliper over braking disc and install on adapter.
Tighten rear caliper assembly to adapter mounting
bolts to 22 Nzm (192 in. lbs.). If required, refer to Rear
Disc Brakes in Group 5 Brakes of this service manual
for required rear brake caliper installation procedure.

(7) If vehicle is equipped with rear drum brakes
install rear brake flex hose onto wheel cylinder and
support plate (Fig. 15). First torque brake hose to
wheel cylinder tube nut to 17 Nzm (145 in. lbs.). Then
torque brake hose bracket to brake support plate bolt
to8Nzm (75 in. lbs).

Fig. 13 Attachment Link To Stabilizer Bar Attaching

Fig. 15 Brake Hose Bracket And Tube Nut

(8) If vehicle has rear drum brakes, brake system
will require bleeding. Refer to Bleeding Brake System
in the Service Adjustments Section of Group 5 Brakes
in this service manual.

(9) Install wheel and tire assembly on vehicle. Then
torque all wheel mounting stud nuts in proper se­quence (Fig. 16) until all nuts are torqued to half

specification. Then repeat tightening sequence to full
specified torque of 129 Nzm (95 ft. lbs.).

Fig. 16 Tightening Wheel Nuts

(10) Lower vehicle to the ground.
(11) Check and reset rear wheel TOE to specifica-

tions if required.

SUSPENSION AND DRIVESHAFTS 2 - 59

STRUT DISASSEMBLY

The rear strut is not serviced and must be replaced
as an assembly if found to be defective. The strut is
available with 2 calibrations, be sure strut is replaced
with an assembly of the same calibration.

The components of the strut assembly listed below
are replaceable if found to be defective.

• Coil spring (Coil springs come in a standard and
high rate be sure spring is replaced with a spring of
the correct rate.)

• Dust shield

• Mount assembly

• Jounce Bumper

• Lower Spring Isolator

• Shaft Nut

(1) Remove strut assembly requiring service from
the vehicle. Refer to Strut Assembly Removal in Ser­vicing Rear Struts, in this section of the service
manual.

(2) Position strut assembly in a vise (Fig. 1). Using
paint or equivalent, mark the strut unit, lower spring
isolator, spring and upper strut mount for indexing of
the parts at assembly.

(3) Position Spring Compressors, Special Tool
C-4838 on the strut assembly spring (Fig. 1). Com­press coil spring until all load is removed from upper
strut mount assembly.

(4) Install Strut Rod Socket, Special Tool, L-4558
on strut shaft nut (Fig. 2). Usea8mmallen wrench
inserted into end of strut shaft to keep strut shaft
from turning (Fig. 2). Remove strut shaft nut from
shaft.

(5) Remove upper strut mount assembly from strut
shaft (Fig. 3).

Fig. 1 Compressing Strut Assembly Coil Spring

Fig. 2 Removing Strut Shaft Nut

(6) Remove the coil spring and spring compressor

as an assembly from the strut (Fig. 4).

(7) Remove the plate, dust shield and jounce

bumper as an assembly from the strut unit (Fig. 5).

(8) Remove lower spring isolator from strut assem-

bly (Fig. 6).

Inspect all disassembled components for signs of
abnormal wear or failure replacing any components
as required. Inspect strut unit for signs of abnormal
oil leakage and for loss of gas charge. To check for
loss of gas charge in strut unit. Push strut shaft into

2 - 60 SUSPENSION AND DRIVESHAFTS

Fig. 3 Upper Strut Mount Removal

Fig. 4 Coil Spring Remove And Replace

body of strut and release, strut shaft should return to
its fully extended position. If strut shaft does not
return to its fully extended position replace strut
unit.

STRUT REASSEMBLY

(1) Install original or new, lower spring isolator on
strut unit (Fig. 6). If installing original isolator align
paint marks on isolator and strut unit.

(2) Install jounce bumper into dust shield (Fig. 7).
Install plate on top of dust shield and into jounce
bumper (Fig. 8).

(3) Install the dust shield, jounce bumper and top
plate as an assembly onto the strut unit (Fig. 5).

(4) Lower the coil spring and compressor onto the
strut unit (Fig. 4) Align the paint mark on the spring
with the paint mark on the strut unit (Fig. 1).

Fig. 5 Plate, Dust Shield And Jounce Bumper

Remove And Replace

Fig. 6 Lower Spring Isolator

(5) Install the upper strut mount assembly onto the
strut shaft, aligning paint marks (Fig. 3). Install the
upper strut mount to strut shaft retaining nut on
strut shaft.

(6) Using Strut Rod Socket, Special Tool, L-4558 and a
8 mm allen wrench to keep strut shaft from turning.
Torque the strut shaft nut to 95 Nzm (70 ft. lbs.).

(7) Equally loosen the Spring Compressors, Special
Tool C-4838 until spring is seated on upper strut
mount and all tension is relieved from the spring
compressors.

(8) Install the strut assembly back into the vehicle.
Refer to Strut Assembly Removal in Servicing Rear
Struts in this section of the service manual.

(9) Check and reset rear wheel TOE to specifica­tions if required.

SUSPENSION AND DRIVESHAFTS 2 - 61

Fig. 7 Jounce Bumper Installed Into Dust Shield

Fig. 8 Plate Installation Into Jounce Bumper And

Dust Shield

SUSPENSION COIL SPRINGS

Springs are rated separately for each side of vehicle
depending on optional equipment and type of service.
During service procedures where both springs are
removed, mark springs (Chalk, Tape, etc.) (Fig. 9) to
ensure installation in original position. If the coils
springs require replacement. Be sure that the

springs needing replacement, are replaced with
springs meeting the correct load and spring
rate for the vehicle.

During service procedures requiring the re­moval or installation of a coil spring with
Spring Compressor, Special Tool C-4838. It is
required that five coils be captured within the
jaws of the tool (Fig. 9).

Fig. 9 Identifying Coil Springs

tion and Maintenance section of this manual, for the
required lifting procedure to be used for this vehicle.

(2) Remove the rear wheel and tire assembly from

the vehicle.

(3) If vehicle is equipped with rear disc brakes,
remove the rear caliper assembly from the adapter.
Refer to Rear Disk Brakes in Group 5 Brakes of this
Service manual for required caliper removal proce­dure. After removing caliper assembly store caliper by
hanging it from frame of vehicle (Fig. 1). Do not let
weight of rear caliper assembly hang from flexible
brake hose. If vehicle is equipped with rear drum
brakes, remove the brake flex hose bracket from the
support plate and wheel cylinder (Fig. 2).

REAR SPINDLE

REMOVE

(1) Raise vehicle on jackstands or centered on a

frame contact type hoist. See Hoisting in the Lubrica-

Fig. 1 Storing Rear Caliper Assembly

2 - 62 SUSPENSION AND DRIVESHAFTS

Fig. 2 Brake Hose Bracket And Tube

(4) If vehicle is equipped with rear disc brakes,
remove rear braking disc from hub. If vehicle is
equipped with rear drum brakes, remove the brake
drum from the hub.

(5) On all rear brake applications, remove rear hub
and bearing assembly cotter pin and nut retainer.
Then remove hub retaining nut and washer from
spindle (Fig. 3). Then remove hub and bearing assem­bly from spindle.

Fig. 4 Brake Support Plate Mounting Bolts

Fig. 3 Rear Hub And Bearing Retaining Nut and

Washer Removal

(6) On vehicles equipped with rear drum brakes.
Remove the 4 bolts attaching the rear brake support
plate to the rear spindle (Fig. 4). Then remove rear
brake support plate with parking brake cable at­tached, from rear spindle.

(7) If vehicle is equipped with Anti-Lock brakes.
Remove speed sensor head from the rear disc brake
adapter (Fig. 5).

(8) On vehicles equipped with rear disc brakes. Re­move the 4 bolts attaching the disc brake adapter to

Fig. 5 Speed Sensor Head Removal From Adapter

the rear spindle (Fig. 6). Then remove the adapter,
disc shield, park brake shoes and park brake cable as
an assembly from spindle.

Fig. 6 Disc Brake Adapter Mounting

(9) If vehicle is equipped with Anti-Lock brakes.
Remove the speed sensor cable routing tube on trail­ing arm and the routing bracket on the trailing arm
bracket to spindle (Fig. 7). If trailing arm is low-

ered from strut with the speed sensor cable at­tached damage to speed sensor cable may occur.

Fig. 7 Speed Sensor Routing Tube And Bracket

(10) Remove bolt attaching trailing arm to trailing
arm bracket on bottom of spindle (Fig. 8).

SUSPENSION AND DRIVESHAFTS 2 - 63

Fig. 9 Lateral Links To Spindle Attaching Bolt

Fig. 8 Trailing Arm To Spindle Bracket Bolt

(11) Remove the bolt (Fig. 9) attaching the lateral
links to the rear spindle assembly.

(12) Loosen and fully remove, the rear spindle to
strut assembly pinch bolt (Fig. 10).

CAUTION: When inserting center punch into rear
spindle, use care so point of center punch does not
puncture strut assembly.

(13) Insert a center punch into the hole on the
spindle (Fig. 11). Center punch must be tapped into
spindle until jammed into hole. This will spread
spindle casting allowing it to be removed from strut
assembly.

(14) Using a hammer, tap on top surface of spindle
driving it down and off the end of the strut assembly
(Fig. 12).

Fig. 10 Spindle To Strut Assembly Pinch Bolt

Fig. 11 Center Punch Installed In Spindle

INSTALLATION

(1) Install spindle onto the bottom of the strut as­sembly (Fig 13). Push and or tap spindle assembly
onto strut, until notch in spindle is tightly seated
against locating tap on strut assembly (Fig. 13). Then

2 - 64 SUSPENSION AND DRIVESHAFTS

Fig. 12 Removing Spindle From Strut Assembly

remove center punch from hole in spindle. Install
spindle to strut assembly pinch bolt into spindle (Fig.

13). Torque spindle to strut assembly pinch bolt to 55
Nzm (40 ft. lbs.).

Fig. 13 Spindle Mounted To Strut Assembly

(2) Install the lateral links to spindle attaching bolt
(Fig. 14) Torque the lateral links to spindle attaching
bolt to 140 Nzm (105 ft. lbs.).

(3) Install bolt attaching trailing arm to trailing
arm bracket on bottom of spindle (Fig. 15). Torque
trailing arm to trailing arm bracket attaching bolt to
100 Nzm (74 ft. lbs.).

(4) If vehicle is equipped with Anti-Lock Brakes.
Mount rear speed sensor cable routing tube to the
rear trailing arm and speed sensor cable routing
bracket to trailing arm bracket at rear spindle (Fig.

16).

(5) On vehicles equipped with rear drum brakes.
Install the rear brake support plate onto the spindle
(Fig. 17). Install the 4 bolts attaching the rear brake
support plate to the rear spindle (Fig. 17). Torque the
brake support plate to spindle mounting bolts to 115
Nzm (85 ft. lbs.).

Fig. 14 Lateral Links To Spindle Attaching Bolt

Fig. 15 Trailing Arm To Spindle Bracket Bolt

Fig. 16 Speed Sensor Routing Tube And Bracket

(6) On vehicles equipped with rear disc brakes. In-

stall the disc brake adapter back on the spindle (Fig.

18) Install the 4 bolts attaching the disc brake
adapter to the rear spindle (Fig. 18). Torque the disc
brake adapter to spindle mounting bolts to 115 Nzm
(85 ft. lbs.).

(7) If vehicle is equipped with Anti-Lock brakes.

Install the speed sensor head into the rear disc brake

SUSPENSION AND DRIVESHAFTS 2 - 65

(8) Install the rear hub and bearing assembly on
the rear spindle. Install hub and bearing assembly
retaining washer and nut on spindle (Fig. 20). Torque
hub and bearing retaining nut to 168 Nzm (124 ft.
lbs).

Fig. 17 Brake Support Plate Mounting Bolts

Fig. 18 Disc Brake Adapter Mounting

adapter (Fig. 19). Torque speed sensor head to
adapter attaching bolt to 7 Nzm (60 in. lbs.).

Fig. 20 Rear Hub And Bearing Retaining Nut and

Washer Removal

(9) If vehicle is equipped with rear disc brakes,
install rear braking disc on hub. If vehicle is equipped
with rear drum brakes, install the brake drum on
hub.

(10) If vehicle is equipped with rear disc brakes,
install rear braking disc on hub. Carefully install rear
brake caliper over braking disc and install on adapter.
Tighten the caliper assembly to adapter mounting
bolts to 22 Nzm (192 in. lbs.). Refer to Rear Disc
Brakes in Group 5 Brakes in this service manual for
required caliper installation procedure.

(11) If vehicle is equipped with rear drum brakes
install rear brake flex hose onto wheel cylinder and
support plate (Fig. 21). Torque the brake hose to
wheel cylinder tube nut to 17 Nzm (145 in. lbs.).
Torque the brake hose bracket to support plate bolt to
8Nzm (75 in. lbs).

(12) If vehicle has rear drum brakes, brake system
will require bleeding. Refer to Bleeding Brake System
in the Service Adjustments Section of Group 5 Brakes
in this service manual.

(13) Install wheel and tire assembly on vehicle.
Tighten the wheel mounting stud nuts in proper se­quence (Fig. 22) until all nuts are torqued to half
specification. Then repeat the tightening sequence to
the full specified torque of 129 Nzm (95 ft. lbs.).

(14) Lower vehicle to the ground.

(15) Check and reset rear wheel TOE to specifica­tions if required.

Fig. 19 Speed Sensor Head Installed In Adapter

2 - 66 SUSPENSION AND DRIVESHAFTS

REAR CROSSMEMBER

The L.H. platform vehicles are available with two
different rear crossmembers depending on the sus­pension package the vehicle was built with. The
crossmembers visually look the same between the
standard and performance suspension packages, but
the mounting location for the lateral links is differ­ent. The performance suspension crossmember is
identified by a identification hole in the crossmem­ber (Fig. 1). The performance crossmember identifi­cation hole is located on left side of crossmember on
the rear vertical wall. If crossmember is replaced

be sure the correct crossmember is installed or
handling of the vehicle will be adversely af­fected.

Fig. 21 Brake Hose Bracket And Tube Nut

Fig. 22 Tightening Wheel Nuts

REMOVE

(1) Raise vehicle on jackstands or centered on a
frame contact type hoist. See Hoisting in the Lubrica­tion and Maintenance section of this manual, for the
required lifting procedure to be used for this vehicle.

(2) Remove both rear wheel and tire assemblies
from the vehicle.

(3) Position a transmission jack under the fuel tank
just forward of the crossmember to help support fuel
tank when crossmember is removed.

(4) Remove the nut and bolt on each side of vehicle
attaching the lateral links to the spindle (Fig. 2).

(5) Remove the 4 bolts attaching rear crossmember
to frame rails (Fig. 3)

(6) Lower the crossmember and lateral links as an
assembly out of the vehicle.

Fig. 1 Rear Suspension Crossmember

Fig. 2 Lateral Link Attachment To Spindle

SUSPENSION AND DRIVESHAFTS 2 - 67

(3) Align lateral links with spindles and install the
lateral link to spindle attaching bolts (Fig. 2). Torque
the lateral link to spindle attaching bolts to 140 Nzm
(105 ft. lbs.).

(4) Remove transmission jack supporting fuel tank.

(5) Install wheel and tire assembly on vehicle.
Tighten the wheel mounting stud nuts in proper se­quence (Fig. 4) until all nuts are torqued to half
specification. Then repeat the tightening sequence to
the full specified torque of 129 Nzm (95 ft. lbs.).

Fig. 3 Crossmember To Frame Rail Attaching Bolts

(7) Transfer lateral links to the replacement cross­member before installing crossmember back in ve­hicle. Adjustable lateral link to be positioned to
the rear of vehicle on crossmember. Torque the
lateral links to crossmember attaching bolts to 140
Nzm (105 ft. lbs.). Install lateral link to crossmem-

ber bolts so head of bolt will be to front of
vehicle when crossmember is installed.

INSTALL

(1) Install the crossmember and lateral links back
into vehicle as an assembly.

(2) Position crossmember on frame rails and install
the 4 crossmember to frame rail attaching bolts (Fig.

3). Torque the crossmember to frame rail attaching
bolts to 95 Nzm (70 ft. lbs.).

Fig. 4 Tightening Wheel Nuts

(6) Lower vehicle to the ground.
(7) Check and reset rear wheel TOE to specifica-

tions if required.

2 - 68 SUSPENSION AND DRIVESHAFTS

REAR STABILIZER BAR SERVICE

REMOVE

(1) Raise vehicle on jackstands or centered on a
frame contact type hoist. See Hoisting in the Lubrica­tion and Maintenance section of this manual, for the
required lifting procedure to be used for this vehicle.

(2) Remove both rear wheel and tire assemblies
from the vehicle.

(3) Position a transmission jack under the fuel tank
just forward of the crossmember to help support fuel
tank when crossmember is removed.

(4) Remove the 4 crossmember to frame rail attach­ing bolts (Fig. 1).

Fig. 2 Stabilizer Bar To Link Attaching

bar attaching nut (Fig. 2). Torque the stabilizer link
to stabilizer bar attaching nut to 95 Nzm (70 ft. lbs.).

(3) Install fuel tank back in vehicle. Refer to Group
14 Fuel, in this service manual for the required fuel
tank installation procedure.

Fig. 1 Crossmember To Frame Rail Attaching Bolts

(5) Remove fuel tank. Refer to Group 14 Fuel, in
this service manual for the required fuel tank re­moval procedure.

(6) Remove the stabilizer bar to link assembly at­taching nuts (Fig. 2)

(7) Remove stabilizer bar and isolator bushings as
an assembly from the vehicle.

STABILIZER BAR AND BUSHING INSPECTION

Inspect for broken or distorted retainers and bush­ings. If bushing replacement is required, bushing can
be removed by opening slit in bushing and removing
bushing from around stabilizer bar.

CAUTION: The sway bar bracket bolts must be re­placed after loosening or removing them. Only use
original equipment bolts as replacements.

(4) Position crossmember on frame rails and install

the 4 crossmember to frame rail attaching bolts (Fig.

1). Torque the crossmember to frame rail attaching
bolts to 95 Nzm (70 ft. lbs.).

(5) Remove transmission jack supporting fuel tank.

(6) Install wheel and tire assembly on vehicle.
Tighten the wheel mounting stud nuts in proper se­quence (Fig. 3) until all nuts are torqued to half
specification. Then repeat the tightening sequence to
the full specified torque of 129 Nzm (95 ft. lbs.).

INSTALL

(1) Install the stabilizer bar and isolator bushings
back into the vehicle as an assembly. Position stabi­lizer bar so it is centered in the vehicle so it does not
contact other suspension components or vehicle body.

(2) Install the stabilizer bar attaching link onto
stabilizer bar. Install the stabilizer link to stabilizer

Fig. 3 Tightening Wheel Nuts

(7) Lower vehicle to the ground.
(8) Check and reset rear wheel TOE to specifica-

tions if required.

SUSPENSION AND DRIVESHAFTS 2 - 69

Fig. 1 Rear Suspension Lateral Links

SERVICING LATERAL LINKS

The lateral links are only serviced as complete as­semblies. The isolator bushings used in the lateral
links are not serviced as separate components. The
left and right lateral links are serviced using different
procedures. See procedures below for the side of the
vehicle requiring service to the lateral links.

LEFT LATERAL LINKS

REMOVE

Raise vehicle on jackstands or centered on a

(1)
frame contact type hoist. See Hoisting in the Lubri­cation and Maintenance section of this manual, for
the required lifting procedure to be used for this
vehicle.

(2) Remove left rear wheel and tire assembly from

the vehicle.

(3) Remove the nut and bolt attaching left lateral

links to the spindle (Fig. 2).

(4) Remove the nut and bolt attaching the left lat­eral links to the rear crossmember (Fig. 3) Remove
lateral links from vehicle.

Fig. 2 Lateral Link Attachment To Spindle

Fig. 3 Left Lateral Links To Crossmember Bolt

INSTALL

(1) Replacement lateral links are installed on the
crossmember in the following order.

• Solid lateral link is installed on crossmember to­ward the front of the vehicle.

• The adjustable lateral link is installed on cross­member toward rear of vehicle, with the adjustable
link positioned toward the spindle (Fig. 1).

2 - 70 SUSPENSION AND DRIVESHAFTS

(2) Install the lateral link attaching bolt at the

spindle and crossmember. Note: Both lateral link

attaching bolts must be install, so head of bolt is
facing front of vehicle (Fig. 2 and 3).

(3) Torque both lateral link attaching bolts to 140

Nzm (105 ft. lbs.).

(4) Install wheel and tire assembly on vehicle.
Tighten the wheel mounting stud nuts in proper se­quence (Fig. 4) until all nuts are torqued to half
specification. Then repeat the tightening sequence to
the full specified torque of 129 Nzm (95 ft. lbs.).

Fig. 5 Lateral Link Attachment To Spindle

Fig. 4 Tightening Wheel Nuts

(5) Lower vehicle to the ground.

(6) Check and reset rear wheel TOE to specifica­tions if required.

RIGHT LATERAL LINKS

To allow for removal of right rear lateral links to
rear crossmember attaching bolt. The rear crossmem­ber will have to be lowered so attaching bolt will clear
fuel tank for removal and installation.

REMOVE

(1) Raise vehicle on jackstands or centered on a
frame contact type hoist. See Hoisting in the Lubrica­tion and Maintenance section of this manual, for the
required lifting procedure to be used for this vehicle.

(2) Remove right rear wheel and tire assembly from
the vehicle.

(3) Remove the nut and bolt attaching right lateral
links to the spindle (Fig. 5).

(4) Position a transmission jack under the fuel tank
just forward of the crossmember to help support fuel
tank when crossmember is lowered.

(5) Remove the 4 crossmember to frame rail attach­ing bolts (Fig. 6).

(6) Lower rear crossmember far enough so right
lateral links to crossmember attaching bolt will clear
fuel tank.

Fig. 6 Crossmember To Frame Rail Attaching Bolts

(7) Remove the nut and bolt attaching the right
lateral links to the rear crossmember (Fig. 7) Remove
lateral links from vehicle.

INSTALL

(1) Replacement lateral links are installed on the
crossmember in the following order.

• Solid lateral link is installed on crossmember to­ward the front of the vehicle.

• The adjustable lateral link is installed on cross­member toward rear of vehicle, with the adjustable
link positioned toward the spindle (Fig. 1).

(2) Install the right lateral links attaching bolt at
the crossmember. Note: Right lateral link attach-

ing bolts MUST be install, so head of bolt is
facing front of vehicle (Fig. 5 and 7).

Fig. 7 Right Lateral Links To Crossmember Bolt

(3) Position crossmember on frame rails and install

the 4 crossmember to frame rail attaching bolts (Fig.

6). Torque the crossmember to frame rail attaching
bolts to 95 Nzm (70 ft. lbs.).

(4) Torque the lateral links to crossmember attach-

ing bolt to 140 Nzm (105 ft. lbs.).

(5) Align right lateral links with spindle and install
the lateral link to spindle attaching bolt (Fig. 5).
Torque the lateral link to spindle attaching bolt to
140 Nzm (105 ft. lbs.).

SUSPENSION AND DRIVESHAFTS 2 - 71

(6) Install wheel and tire assembly on vehicle.
Tighten the wheel mounting stud nuts in proper se­quence (Fig. 8) until all nuts are torqued to half
specification. Then repeat the tightening sequence to
the full specified torque of 129 Nzm (95 ft. lbs.).

Fig. 8 Tightening Wheel Nuts

(7) Lower vehicle to the ground.

(8) Check and reset rear wheel TOE to specifica­tions if required.

2 - 72 SUSPENSION AND DRIVESHAFTS

ALIGNMENT SPECIFICATIONS AT CURB HEIGHT

1994 New Yorker, LHS, Concorde, Intrepid and Vision
Publication No. 81-270-4140
TSB 02-13-94 September 23, 1994

SPECIFICATIONS

FRONT SUSPENSION TORQUE SPECIFICATIONS

REAR SUSPENSION TORQUE SPECIFICATIONS