Christie LX501 User Manual

LX501/LX601i

User Manual-Technical Guide

020-000503-01

Projector

LX501/LX601i User Manual-Technical Guide

User's Manual (detailed) - Operating Guide Technical

Example of computer signal

Resolution (H x V) H. frequency (kHz) V. frequency (Hz) Rating Signal mode

720 x 400 640 x 480 31.5 59.9 VESA VGA (60Hz) 640 x 480 37.9 72.8 VESA VGA (72Hz) 640 x 480 37.5 75.0 VESA VGA (75Hz) 640 x 480 43.3 85.0 VESA VGA (85Hz) 800 x 600 35.2 56.3 VESA SVGA (56Hz) 800 x 600 37.9 60.3 VESA SVGA (60Hz) 800 x 600 48.1 72.2 VESA SVGA (72Hz) 800 x 600 46.9 75.0 VESA SVGA (75Hz) 800 x 600 53.7 85.1 VESA SVGA (85Hz)

832 x 624 49.7 74.5 Mac 16” mode 1024 x 768 48.4 60.0 VESA XGA (60Hz) 1024 x 768 56.5 70.1 VESA XGA (70Hz) 1024 x 768 60.0 75.0 VESA XGA (75Hz) 1024 x 768 68.7 85.0 VESA XGA (85Hz) 1152 x 864 67.5 75.0 VESA 1280 x 768 47.7 60.0 VESA W-XGA (60Hz) 1280 x 800 49.7 60.0 VESA 1280 x 960 60.0 60.0 VESA

1280 x 1024 64.0 60.0 VESA SXGA (60Hz) 1280 x 1024 80.0 75.0 VESA SXGA (75Hz)

* 1280 x 1024 91.1 85.0 VESA SXGA (85Hz)

1400 x 1050 65.2 60.0 VESA SXGA+ (60Hz)

1440 x 900 55.9 59.9 VESA WXGA+ (60Hz)

* 1600 x 1200 75.0 60.0 VESA UXGA (60Hz)

* Supported except for HDMITM input.

37.9 85.0 VESA TEXT

1152 x 864 (75Hz)

1280 x 800 (60Hz) 1280 x 960 (60Hz)

NOTE • Be sure to check jack type, signal level, timing and resolution before

connecting this projector to a computer.

•

Some computers with multiple display screen modes may unavailable with this projector.

• Depending on the input signal, full-size display may unavailabel in some cases. Refer to the number of display pixels above.

• Although the projector can display signals with resolution up to UXGA (1600x1200), the signal will be converted to the projector’s panel resolution before being displayed. The best display performance will be achieved if the resolutions of the input signal and projector panel are identical.

• Automatic adjustment may not function correctly with some input signals.

• The image may not be displayed correctly when the input sync signal is a composite sync or a sync on G.

LX501/LX601i User Manual-Technical Guide 020-000503-01 Rev. 1 (03-2012)

Initial set signals

The following signals are used for the initial settings. The signal timing of some computer models may be different. In such case, adjust the items V POSITION and H POSITION in the IMAGE menu.

Back porch (B) Front porch (D) Back porch (b) Front porch (d)

Data Data H. Sync. V. Sync.

Sync (A) Sync (a)

Active video (C)

Active video (c)

Resolution

(H x V)

720 x 400 640 x 480 3.8 1.9 25.4 0.6 2 33 480 10 VGA (60Hz) 640 x 480 1.3 4.1 20.3 0.8 3 28 480 9 VGA (72Hz) 640 x 480 2.0 3.8 20.3 0.5 3 16 480 1 VGA (75Hz) 640 x 480 1.6 2.2 17.8 1.6 3 25 480 1 VGA (85Hz) 800 x 600 2.0 3.6 22.2 0.7 2 22 600 1 SVGA (56Hz) 800 x 600 3.2 2.2 20.0 1.0 4 23 600 1 SVGA (60Hz) 800 x 600 2.4 1.3 16.0 1.1 6 23 600 37 SVGA (72Hz) 800 x 600 1.6 3.2 16.2 0.3 3 21 600 1 SVGA (75Hz) 800 x 600 1.1 2.7 14.2 0.6 3 27 600 1 SVGA (85Hz)

832 x 624 1.1 3.9 14.5 0.6 3 39 624 1 Mac 16" mode 1024 x 768 2.1 2.5 15.8 0.4 6 29 768 3 XGA (60Hz) 1024 x 768 1.8 1.9 13.7 0.3 6 29 768 3 XGA (70Hz) 1024 x 768 1.2 2.2 13.0 0.2 3 28 768 1 XGA (75Hz) 1024 x 768 1.0 2.2 10.8 0.5 3 36 768 1 XGA (85Hz)

1152 x 864 1.2 2.4 10.7 0.6 3 32 864 1

1280 x 768 1.7 2.5 16.0 0.8 3 23 768 1 W-XGA (60Hz)

1280 x 800 1.6 2.4 15.3 0.8 3 24 800 1

1280 x 960 1.0 2.9 11.9 0.9 3 36 960 1

1280 x 1024 1.0 2.3 11.9 0.4 3 38 1024 1 SXGA (60Hz) 1280 x 1024 1.1 1.8 9.5 0.1 3 38 1024 1 SXGA (75Hz) 1280 x 1024 1.0 1.4 8.1 0.4 3 44 1024 1 SXGA (85Hz) 1400 x 1050 1.2 2.0 11.4 0.7 3 33 1050 1 SXGA+ (60Hz)

1440 x 900 1.4 2.2 13.5 0.8 6 25 900 3 WXGA+ (60Hz)

1680 x 1050 1.2 1.9 11.5 0.7 6 30 1050 3 WSXGA+ (60Hz) 1600 x 1200 1.2 1.9 9.9 0.4 3 46 1200 1 UXGA (60Hz)

1920 x 1200 0.208 0.519 12.47 0.312 6 26 1200 3

LX501/LX601i User Manual-Technical Guide 020-000503-01 Rev. 1 (03-2012)

Horizontal signal timing (μs) Vertical signal timing (lines)

(A) (B) (C) (D) (a) (b) (c) (d)

2.0 3.0 20.3 1.0 3 42 400 1 TEXT

Signal mode

1152 x 864

(75Hz)

1280 x 800

(60Hz)

1280 x 960

(60Hz)

W-UXGA (60Hz)

Reduced Blanking

Connection to the ports

NOTICE

►Use the cables with straight plugs, not L-shaped ones, as the input ports of the projector are recessed. ►Only the signal that is input from the COMPUTER IN1 or IN2 can be output from the MONITOR OUT port.

COMPUTER IN1, BMONITOR OUT

D-sub 15pin mini shrink jack <Computer signal>

• Video signal: RGB separate, Analog, 0.7Vp-p, 75Ω terminated (positive)

• H/V. sync. signal: TTL level (positive/negative)

• Composite sync. signal: TTL level <Component video signal>

• Video signal: Y with composite sync, Analog, 1.0±0.1Vp-p, 75Ω terminated Cb/Pb, Analog, 0.7±0.1Vp-p, 75Ω terminated Cr/Pr, Analog, 0.7±0.1Vp-p 75Ω terminated

• System: 480i@60, 480p@60, 576i@50, 720p@50/60, 1080i@50/60

⑪⑮⑭⑬⑫

⑥⑩⑨⑧⑦

①⑤④③②

Pin Signal Pin Signal

1 Video Red, Cr/Pr 9 (No connection) 2 Video Green, Y 10 Ground 3 Video Blue, Cb/Pb 11 (No connection) 4 (No connection) 12

: SDA (DDC data)

: (No connection)

5 Ground 13 H. sync / Composite sync. 6 Ground Red, Ground Cr/Pr 14 V. sync. 7 Ground Green, Ground Y

: SCL (DDC clock)

: (No connection)

8 Ground Blue, Ground Cb/Pb

LX501/LX601i User Manual-Technical Guide 020-000503-01 Rev. 1 (03-2012)

Connection to the ports (continued)

COMPUTER IN2 CG/Y, DB/Cb/Pb,

R/Cr/Pr, FH, GV

C ED

F G

BNC jack x5 <Computer signal>

• Video signal: RGB separate, Analog, 0.7Vp-p, 75Ω terminated (positive)

• H/V. sync. signal: TTL level (positive/negative)

• Composite sync. signal: TTL level

• Video signal: Y with composite sync, Analog, 1.0±0.1Vp-p, 75Ω terminated Cb/Pb, Analog, 0.7±0.1Vp-p, 75Ω terminated Cr/Pr, Analog, 0.7±0.1Vp-p 75Ω terminated

• System: 480i@60, 480p@60, 576i@50, 720p@50/60, 1080i@50/60

HDMI 1, IHDMI 2

HDMITM connector

• Audio signal: Linear PCM (Sampling rate; 32/44.1/48 kHz)

②⑥⑩⑨⑧

①⑤④③

⑯

⑦⑪⑮⑭⑬⑫⑲⑱⑰

Pin Signal Pin Signal Pin Signal

1 T.M.D.S. Data2 + 8 T.M.D.S. Data0 Shield 15 SCL 2 T.M.D.S. Data2 Shield 9 T.M.D.S. Data0 - 16 SDA 3 T.M.D.S. Data2 - 10 T.M.D.S. Clock + 17 DDC/CEC Ground

4 T.M.D.S. Data1 + 11 T.M.D.S. Clock Shield

5 T.M.D.S. Data1 Shield 12 T.M.D.S. Clock -

+5V Power

19 Hot Plug Detect 6 T.M.D.S. Data1 - 13 CEC 7 T.M.D.S. Data0 + 14 Reserved (N.C. on device)

LX501/LX601i User Manual-Technical Guide 020-000503-01 Rev. 1 (03-2012)

Connection to the ports (continued)

L JK

COMPONENT JY, KCb/Pb, LCr/Pr

RCA jack x3

• Component video signal, Analog:

-Y with composite sync, 1.0±0.1Vp-p, 75Ω terminated

-Cb/Pb, 0.7±0.1Vp-p, 75Ω terminated

-Cr/Pr, 0.7±0.1Vp-p 75Ω terminated

• System: 480i@60, 480p@60, 576i@50, 720p@50/60, 1080i@50/60, 1080p@50/60

S-VIDEO

Mini DIN 4pin jack

• S-video signal, Analog:

-Brightness signal with composite sync, 1.0±0.1Vp-p, 75Ω terminated

-Color signal, 0.286Vp-p (NTSC, burst), 75Ω terminated

0.300Vp-p (PAL/SECAM, burst) 75Ω terminated

• System: NTSC, PAL, SECAM, PAL-M, PAL-N, NTSC4.43, PAL(60Hz)

④③

②

①

Pin Signal

1 C (color signal) 2 Y (brightness signal) 3 Ground 4 Ground

VIDEO

RCA jack

• Composite video signal, Analog, 1.0±0.1Vp-p, 75Ω terminator

• System: NTSC, PAL, SECAM, PAL-M, PAL-N, NTSC4.43, PAL(60Hz)

LX501/LX601i User Manual-Technical Guide 020-000503-01 Rev. 1 (03-2012)

Connection to the ports (continued)

AUDIO IN1, PAUDIO IN2

S T

Ø3.5 stereo mini jack

•

Analog, 500 mVrms, 47kΩ input impedance

AUDIO IN3 QL, RR AUDIO OUT SL, TR

RCA jack x2 RCA jack x2

•

Analog, 500 mVrms, 47kΩ input impedance

CONTROL

D-sub 9pin plug * About the details of RS-232C communication,

please refer to the next section.

Pin Signal Pin Signal Pin Signal

1 (No connection) 4 (No connection) 7 RTS 2 RD 5 Ground 8 CTS 3 TD 6 (No connection) 9 (No connection)

•

Analog, 500 mVrms, 1kΩ output impedance

⑥⑦⑧⑨

⑤④③

①②

LX501/LX601i User Manual-Technical Guide 020-000503-01 Rev. 1 (03-2012)

Connection to the ports (continued)

LAN

RJ-45 jack * About the details of network communication,

①⑤

please refer to the Network Guide.

Pin Signal Pin Signal Pin Signal

1 TX+ 4- 72 TX- 5 -

3 RX+ 6 RX-

④③②⑥⑧

⑦

USB TYPE A

USB A type jack x2

Pin Signal

1 +5V 2 - Data 3 + Data 4 Ground

①④③②

USB

TYPE B

USB B type jack

Pin Signal

1 +5V 2 - Data 3 + Data 4 Ground

①④③②

REMOTE CONTROL YIN, ZOUT

Ø3.5 stereo mini jack

LX501/LX601i User Manual-Technical Guide 020-000503-01 Rev. 1 (03-2012)

Connection to the ports (continued)

To input SCART RGB signal;

ex.

SCART cable (plug)

Audio L

Audio R

Video

SCART

connector

(jack)

To input SCART RGB signal to the projector, use a SCART to RCA cable. Connect the plugs refer to above ex. For more reference, please consult your dealer.

RCA plugs

LX501/LX601i User Manual-Technical Guide 020-000503-01 Rev. 1 (03-2012)

RS-232C Communication

When the projector connects to the computer by RS-232C communication, the projector can be controlled with RS-232C commands from the computer.

For details of RS-232C commands, refer to RS-232C Communication / Network command table (

18

Connection

Turn off the projector and the computer.

Connect the projector's CONTROL port and the computer's RS-232C port

with a RS-232C cable (cross). Use the cable that fulﬁ lls the speciﬁ cation

shown in ﬁ gure

Turn the computer on, and after the computer has started up turn the projector

on. Set the COMMUNICATION TYPE to OFF in the COMMUNICATION menu of the

OPTION - SERVICE menu.

RS-232C

RS-232C cable

(cross)

RS-232C port

of the computer

9876

5432

CD (1) (1) RD(2) (2) RD TD (3) (3) TD DTR (4) (4) GND (5) (5) GND DSR (6) (6) RTS (7) (7) RTS DTS (8) (8) CTS RI (9) (9)

LX501/LX601i User Manual-Technical Guide 020-000503-01 Rev. 1 (03-2012)

CONTROL

CONTROL port

of the projector

⑥⑦⑧⑨

①②

⑤④③

−

RS-232C Communication (continued)

Communicaion settings

1. Protocol

19200bps, 8N1

2. Command format

("h" shows hexadecimal)

Byte Number

Command

Action

<SET>

Change setting to desired value [(cL)(cH)] by [(bL)(bH)].

<GET>

Read projector internal setup value [(bL) (bH)] .

<INCREMENT> Increment setup value [(bL)(bH)] by 1.

<DECREMENT> Decrement setup value [(bL)(bH)] by 1.

<EXECUTE> Run a command [(bL)(bH)].

01 2 3456

Header Data

Header

code

LH LHLHLHLHLH

BEh EFh 03h 06h 00h

Packet

Data

size

CRC

ﬂag

(aL) (aH) 01h 00h (bL) (bH) (cL) (cH)

(aL) (aH) 02h 00h (bL) (bH) 00h 00h

(aL) (aH) 04h 00h (bL) (bH) 00h 00h

(aL) (aH) 05h 00h (bL) (bH) 00h 00h

(aL) (aH) 06h 00h (bL) (bH) 00h 00h

789101112

Action Type

[Header code] [Packet] [Data size]

Set [BEh, EFh, 03h, 06h, 00h] to byte number 0 to 4.

[CRC ﬂag]

For byte number

table (

18).

5, 6,

refer to

RS-232C Communication / Network command

[Action]

Set functional code to byte number 7, 8. <SET> = [01h, 00h], <GET> = [02h, 00h], <INCREMENT> = [04h, 00h] <DECREMENT> = [05h, 00h], <EXECUTE> = [06h, 00h] Refer to the Communication command table

(

above

[Type] [Setting code]

For byte number 9 to 12, refer to RS-232C Communication / Network

command table (

18).

Setting

code

LX501/LX601i User Manual-Technical Guide 020-000503-01 Rev. 1 (03-2012)

+ 28 hidden pages