Christie LX34 103-002001 User Manual

User's Manual

103-002001

MODEL

DRAFT

2

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-

SERVICEABLE PARTS INSIDE EXCEPT LAMP REPLACEMENT. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.

THIS SYMBOL INDICATES THAT DANGEROUS
VOLTAGE CONSTITUTING A RISK OF ELECTRIC
SHOCK IS PRESENT WITHIN THIS UNIT.

THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT
OPERATING AND MAINTENANCE INSTRUCTIONS IN THE
USER'S MANUAL WITH THIS UNIT.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

Before operating this projector, read this manual thoroughly and operate the projector properly.
This projector provides many convenient features and functions. Operating the projector properly enables you to
manage those features and maintains it in better condition for a considerable time.
Improper operation may result in not only shortening the product-life, but also malfunctions, fire hazard, or other
accidents.
If your projector seems to operate improperly, read this manual again, check operations and cable connections and try
the solutions in the “TROUBLESHOOTING” section at the end of this booklet. If the problem still persists, contact the
sales dealer where you purchased the projector or the service center.

TO THE OWNER

SAFETY PRECAUTIONS

WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO

RAIN OR MOISTURE.

● This projector produces intense light from the projection lens. Do not stare directly into the lens. Eye damage
could result. Be especially careful that children do not stare directly into the beam.

● Do not use projectors with whiteboards that produce a very bright glare or 'hot spot'. This seems to happen
most on shiny surfaces.

● This projector should be set in the way indicated. If not, it may result in a fire hazard.

● Take appropriate space on the top, sides and rear of the projector

cabinet for allowing air circulation and cooling the projector.
Minimum distance should be taken. If the projector is to be built
into a compartment or similarly enclosed, the minimum distances
must be maintained. Do not cover the ventilation slot on the
projector. Heat build-up can reduce the service life of your
projector, and can also be dangerous.

● Do not put any flammable object or spray can near the projector, hot air is exhausted from the ventilation
holes.

● Remote Control Unit, supplied to this projector, emits the laser beam as the laser pointer function from Laser
Light Window while pressing LASER button (for 1 minute / LASER POINTER INDICATOR lights red to indicate
laser emission). Do not look into Laser Light Window or shine the laser beam on yourself or other people. Eye
damage may result.

● If the projector is not to be used for an extended time, unplug the projector from the power outlet.

READ AND KEEP THIS USER'S MANUAL FOR LATER USE.

SIDE and TOP

REAR

20cm

50cm 50cm

50cm

3

SAFETY INSTRUCTIONS

All the safety and operating instructions should be read before
the product is operated.

Read all of the instructions given here and retain them for later
use. Unplug this projector from AC power supply before
cleaning. Do not use liquid or aerosol cleaners. Use a damp
cloth for cleaning.

Follow all warnings and instructions marked on the projector.

For added protection to the projector during a lightning storm,
or when it is left unattended and unused for long periods of
time, unplug it from the wall outlet. This will prevent damage
due to lightning and power line surges.

Do not expose this unit to rain or use near water... for
example, in a wet basement, near a swimming pool, etc...

Do not use attachments not recommended by the
manufacturer as they may cause hazards.

Do not place this projector on an unstable cart, stand, or table.
The projector may fall, causing serious injury to a child or
adult, and serious damage to the projector. Use only with a
cart or stand recommended by the manufacturer, or sold with
the projector. Wall or shelf mounting should follow the
manufacturer's instructions, and should use a mounting kit
approved by the manufacturers.

An appliance and cart combination should
be moved with care. Quick stops,
excessive force, and uneven surfaces
may cause the appliance and cart
combination to overturn.

Slots and openings in the back and bottom of the cabinet are
provided for ventilation, to insure reliable operation of the
equipment and to protect it from overheating.

The openings should never be covered with cloth or other
materials, and the bottom opening should not be blocked by
placing the projector on a bed, sofa, rug, or other similar
surface. This projector should never be placed near or over a
radiator or heat register.

This projector should not be placed in a built-in installation
such as a book case unless proper ventilation is provided.

Never push objects of any kind into this projector through
cabinet slots as they may touch dangerous voltage points or
short out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the projector.

This projector should be operated only from the type of power
source indicated on the marking label. If you are not sure of
the type of power supplied, consult your authorized dealer or
local power company.

Do not overload wall outlets and extension cords as this can
result in fire or electric shock. Do not allow anything to rest on
the power cord. Do not locate this projector where the cord
may be damaged by persons walking on it.

Do not attempt to service this projector yourself as opening or
removing covers may expose you to dangerous voltage or
other hazards. Refer all servicing to qualified service
personnel.

Unplug this projector from wall outlet and refer servicing to
qualified service personnel under the following conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the projector.
c. If the projector has been exposed to rain or water.
d. If the projector does not operate normally by following the

operating instructions. Adjust only those controls that are
covered by the operating instructions as improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the projector to normal operation.

e. If the projector has been dropped or the cabinet has been

damaged.

f. When the projector exhibits a distinct change in

performance-this indicates a need for service.

When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer that have the same characteristics as the
original part. Unauthorized substitutions may result in fire,
electric shock, or injury to persons.

Upon completion of any service or repairs to this projector, ask
the service technician to perform routine safety checks to
determine that the projector is in safe operating condition.

Voor de klanten in Nederland

Bij dit product zijn batterijen
geleverd.
Wanneer deze leeg zijn,
moet u ze niet weggooien
maar inleveren als KCA.

4

COMPLIANCES

The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it.

AC Power Cord for the United States and Canada :

AC Power Cord used in the United States and Canada is listed by the Underwriters
Laboratories (UL) and certified by the Canadian Standard Association (CSA).
AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure that the
plug will fit into the power outlet. Do not try to defeat this safety feature. Should you be
unable to insert the plug into the outlet, contact your electrician.

THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE.

AC POWER CORD REQUIREMENT

Federal Communication Commission Notice

Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures :

– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.

Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules.
Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such

changes or modifications should be made, you could be required to stop operation of the equipment.

Model Number : 103-002001
Trade Name : Christie
Responsible party : CHRISTIE DIGITAL SYSTEMS, Inc.
Address : 10550 Camden Drive Cypress, CA 90630 USA

Telephone No. : [phone]

GROUND

5

TABLE OF CONTENTS

FEATURES AND DESIGN 6

BEFORE OPERATION 14

COMPUTER INPUT 22

VIDEO INPUT 31

SETTING 36

APPENDIX 38

PREPARATION 7

NAME OF EACH PART OF PROJECTOR 7
SETTING-UP PROJECTOR 8

CONNECTING AC POWER CORD 8
POSITIONING PROJECTOR 9
ADJUSTABLE FEET 10
MOVING PROJECTOR 10

CONNECTING PROJECTOR 11

TERMINALS OF PROJECTOR 11
CONNECTING TO COMPUTER 12
CONNECTING TO VIDEO EQUIPMENT 13

OPERATION OF REMOTE CONTROL UNIT 14

LASER POINTER FUNCTION 14
REMOTE CONTROL BATTERIES INSTALLATION 15

TOP CONTROLS AND INDICATORS 16
OPERATING ON-SCREEN MENU 17

HOW TO OPERATE ON-SCREEN MENU 17
FLOW OF ON-SCREEN MENU OPERATION 17
MENU BAR 18

SELECTING INPUT SOURCE 22
SELECTING COMPUTER SYSTEM 23

COMPATIBLE COMPUTER SPECIFICATIONS 24

PC ADJUSTMENT 25

AUTO PC ADJUSTMENT 25
MANUAL PC ADJUSTMENT 26

PICTURE IMAGE ADJUSTMENTS 28

IMAGE LEVEL SELECT 28
IMAGE LEVEL ADJUSTMENT 29

PICTURE SCREEN ADJUSTMENT 30

SELECTING INPUT SOURCE 31
SELECTING VIDEO SYSTEM 32
PICTURE IMAGE ADJUSTMENTS 33

IMAGE LEVEL SELECT 33
IMAGE LEVEL ADJUSTMENT 34

PICTURE SCREEN ADJUSTMENT 35

SETTING MENU 36

LAMP REPLACEMENT 38

LAMP REPLACE 38
LAMP REPLACE COUNTER 39

OPERATING WIRELESS MOUSE 40
MAINTENANCE 41

WARNING TEMP. INDICATOR 41
AIR FILTER CARE AND CLEANING 41
CLEANING PROJECTION LENS 41

TROUBLESHOOTING 42
TECHNICAL SPECIFICATIONS 44

CONFIGURATIONS OF TERMINALS 45
OPTIONAL PARTS 46

BASIC OPERATION 19

TURNING ON / OFF PROJECTOR 19
ADJUSTING SCREEN 20

ZOOM ADJUSTMENT 20
FOCUS ADJUSTMENT 20
LENS SHIFT ADJUSTMENT 20
KEYSTONE ADJUSTMENT 20
PICTURE FREEZE FUNCTION 21
NO SHOW FUNCTION 21
P-TIMER FUNCTION 21

SOUND ADJUSTMENT 21

TRADEMARKS

● Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer,Inc.

● IBM, VGA, XGA, and PS/2 are trademarks or registered trademarks of International Business Machines, Inc.

● Windows and PowerPoint are registered trademarks of Microsoft Corporation.

● Each name of corporations or products in the user's manual is a trademark or a registered trademark of its

respective corporation.

6

FEATURES AND DESIGN

This Multimedia Projector is designed with the most advanced technology for portability, durability, and ease of use. This
projector utilizes built-in multimedia features, a palette of 16.77 million colors, and matrix liquid crystal display (LCD)
technology.

◆ Compatibility

This projector widely accepts various video and
computer input signals including;

● Computers

IBM-compatible or Macintosh computer up to 1280
x 1024 resolution.

● 6 Color Systems

NTSC, PAL, SECAM, NTSC 4.43, PAL-M or PAL­N color system can be connected.

● Component Video

Component video signal, such as a DVD player
output high definition TV signals including 480i,
480p, 575i, 575p, 720p, 1035i or 1080i, can be
connected.

● S-Video

S-Video signal, such as a S-VHS VCR output
signal, can be connected.

◆ High Resolution Image

This projector provides 1024 x 768 dots resolution for
computer input and 800 horizontal TV lines. Resolution
from a computer between XGA (1024 x 768) and SXGA
(1280 x 1024) is compressed into 1024 x 768 dots. This
projector cannot display image of over 1280 x 1024 dots.
When resolution of your computer is more than 1280 x
1024, reset a computer output for lower resolution.

◆ Multi-Scan System

This projector has Multi-Scan System to conform to
almost all computer output signals quickly. There is no
need for troublesome manual adjustment of frequency
and other settings.

◆ Keystone Correction

Positioning of a projector may result in distorted image
being displayed in a trapezoid shape. Keystone
Correction solves this problem by digitally altering
projection to produce undistorted images.

◆ One-Touch Auto PC Adjustment

Incoming computer video signals are recognized and the
best adjustment is automatically set by Auto PC
Adjustment. No complicated setup is necessary and
projection is always precise.

◆ Digital Zoom (for Computer)

Digital Zoom function adjusts the image size to approx.
1/4 ~ 49 times of original image size, allowing you to
focus on crucial information at a presentation.

◆ Compact Design

This projector is extremely compact in size and weight.
It is designed to carry and work anywhere you wish to
use.

◆ Power Management

Power Management function is provided to reduce power
consumption while a projector is not in use.
This Power Management function operates to turn
Projection Lamp off when a projector detects signal
interruption and any button is not pressed over 5
minutes. Projection Lamp is automatically turned on
again when a projector detects signal or any operation
button is pressed.
This projector is shipped with this function ON.

◆ Wireless Mouse

Remote Control Unit supplied with this projector has
Wireless Mouse function for a connected computer. This
function enables you to operate both projector and
computer with Remote Control Unit only.

◆ Digital Visual Interface

This projector is equipped with DVI 29-pin terminal for
connecting DVI output from a computer.

◆ Laser Pointer Function

Remote Control Unit supplied with this projector includes
Laser Pointer function. This function helps you to make
a smart presentation on a projected screen.

◆ Progressive Scan Function

This function converts interlace video signals into
progressive scan signals and provide fine picture quality.

◆ Motor-driven Lens Shift

Projection lens can be moved up and down with motor­driven lens shift function. This function makes it easy to
provide projected image where you want.
Zoom and focus can be also adjusted with motor-driven
operation.

◆ Multilanguage Menu Display

Operation menu is displayed in; English, German,
French, Italian, Spanish, Portuguese, Dutch, Swedish,
Russian, Chinese, Korean or Japanese.

7

PREPARATION

NAME OF EACH PART OF PROJECTOR

BOTTOM

BACK

HOT AIR EXHAUSTED !

Air blown from Exhaust Vents is hot.
When using or installing projector,
following precautions should be taken.

● Do not put any flammable object near
this vent.

● Keep side grill at least 3’(1m) away from
any object, especially heat-sensitive
object.

● Do not touch this area, especially screw
and metallic part. This area will become
hot while a projector is used.

This projector detects internal
temperature and automatically controls
operating power of Cooling Fans.

FRONT

This projector is equipped with Cooling
Fans for protection from overheating.
Pay attention to the following to ensure
proper ventilation and avoid a possible
risk of fire and malfunction.

● Do not cover vent slots.

● Keep side and bottom clear of any

object. Obstructions may block
cooling air.

PROJECTION LENS

LENS COVER

EXHAUST VENTS

INFRARED

REMOTE RECEIVER

CARRY HANDLE

SPEAKERS

INFRARED

REMOTE RECEIVER

POWER CORD CONNECTOR

TERMINALS

AND CONNECTORS

TOP CONTROLS

AND INDICATORS

LAMP COVER

ADJUSTABLE FEET

AND

FEET LOCK LATCHES

AIR FILTERS

AIR INTAKE VENTS

AIR INTAKE VENT

AIR INTAKE VENT

SETTING-UP PROJECTOR

8

PREPARATION

This projector uses nominal input voltages of 100-120 V or 200-240
V AC. This projector automatically selects the correct input
voltage. It is designed to work with single-phase power systems
having a grounded neutral conductor. To reduce risk of electrical
shock, do not plug into any other type of power system.
Consult your authorized dealer or service station if you are not sure
of the type of power supply being in use.
Connect a projector with a peripheral equipment before turning a
projector on. (Refer to pages 11 ~ 13 for connection.)

CAUTION

For safety, unplug AC Power Cord when an appliance is not
used.
When this projector is connected to the outlet with AC Power
Cord, an appliance is in Stand-by Mode and consumes a little
electric power.

CONNECTING AC POWER CORD

Connect AC Power Cord (supplied) to a projector.
The AC outlet must be near this equipment and
must be easily accessible.

To POWER CORD
CONNECTOR on the
projector.

Projector side

AC Outlet side

Ground

CAUTION

The AC Power Cord must meet the requirement of the country where you use the projector.
Confirm the AC plug type with the chart below. The proper AC Power Cord must be used.
If the supplied AC Power Cord does not match the AC outlet, contact your sales dealer.

To AC Outlet.

(120 V AC)

For Continental Europe

For U.S.A. and Canada

To AC Outlet.

(200 - 240 V AC)

9

PREPARATION

POSITIONING PROJECTOR

● This projector is designed to project on a flat
projection surface.

● Projector can be focused from 4.1’ (1.2m) ~ 32.8’
(10.0m).

● Refer to figure below to adjust screen size.

Screen
Size

Distance

39”

30”

4.1’ (1.2m)

ROOM LIGHT

Brightness in room has a great influence on
picture quality. It is recommended to limit
ambient lighting in order to provide best
image.

Min. Zoom

Max. Zoom

100”

77”

10.8’ (3.3m)

150”

115”

16.4’ (5.0m)

200”

154”

22.0’ (6.7m)

250”

192”

27.6’ (8.4m)

300”

231”

32.8’ (10.0m)

LENS SHIFT ADJUSTMENT

Projection lens can be moved up and down with motor-driven lens shift function. This function makes it easy to
provide projected image where you want. U/D ratio can be adjusted 10 : 0 ~ 1 : 1 (refer to figure below.). Refer
to P 20 for operation.

Highest (10 : 0) Lowest (1 : 1)

10.8’(3.3m)

4.1’(1.2m)

39”

30”

100”

77”

16.4’(5.0m)

150”

115”

32.8’(10.0m)

22.0’(6.7m)

200”

154”

Max. Zoom

Min. Zoom

300”

231”

1

10 : 0

1

10

PREPARATION

CAUTION IN CARRYING OR TRANSPORTING THE PROJECTOR

● Do not drop or bump a projector, otherwise damages or malfunctions may result.

● When carrying a projector, use a suitable carrying case.

● Do not transport a projector by using a courier or transport service in an unsuitable transport case. This may cause

damage to a projector. To transport a projector through a courier or transport service, consult your dealer for best
way.

MOVING PROJECTOR

CAUTION

Dust Cover (supplied) is intended for protection from dust and
scratches on the surface of a cabinet, and it is not designed to
protect an appliance from external forces. Do not transport a
projector through a courier or transport services with this cover.
The projector can be damaged. When handling a projector, do not
drop, bump, subject it to strong forces or put other things on the
cabinet.

Use Carry Handle when moving a projector.
When moving a projector, replace Lens Cover and retract
Adjustable Feet to prevent damage to the lens and cabinet.
When a projector is not in use for an extended period, put it into
the case (dust cover) supplied with a projector.

ADJUSTABLE FEET

Picture tilt and projection angle can be adjusted by rotating
ADJUSTABLE FEET. Projection angle can be adjusted to 10
degrees.

Lift the front of a projector and pull FEET LOCK LATCHES
on the both sides of a projector.

1

ADJUSTABLE FEET

FEET LOCK
LATCHES

Release FEET LOCK LATCHES to lock ADJUSTABLE FEET
and rotate ADJUSTABLE FEET to fine tune position and tilt.

2

To retract ADJUSTABLE FEET, lift the front of a projector
and pull and undo FEET LOCK LATCHES.
Keystone distortion of a projected image can be adjusted by
Menu Operation. (Refer to P20 and 36.)

3

NOTE :

THIS PROJECTOR SHOULD BE SET IN THE WAY
INDICATED. PROJECTION LAMP MAY MALFUNCTION.

11

CONNECTING PROJECTOR

TERMINALS OF PROJECTOR

When controlling the computer
with Remote Control Unit of
this projector, connect the
mouse port of your personal
computer to this connector.
(Refer to P12.)

Connect the S-VIDEO
output from video
equipment to this
jack. (Refer to P13.)

Connect an audio output
(stereo) from computer to
these jacks.
(Refer to P12.)

CONTROL PORT CONNECTOR

COMPUTER AUDIO

INPUT (1 and 2) JACKS

Connect the audio output
from video equipment to
these jacks.
(Refer to P13.)

● When the audio output

is monaural, connect it
to L (MONO) jack.

AUDIO INPUT JACKS

VIDEO INPUT JACKS

S-VIDEO INPUT JACK

Connect the component
video output from video
equipment to connect the
component video outputs to
Y, Pb/Cb and Pr/Cr jacks.
(Refer to P13.)

COMPUTER INPUT 2 (DIGITAL/ANALOG)

Media Card Imager / Wireless Imager

TERMINAL

This projector has input and output terminals on its back for connecting computers and video equipment. Refer to figures on
pages 11 to 13 and connect properly.

Connect an external
audio amplifier to this
jack.
(Refer to P12, 13.)

This projector uses a micro
processor to control this unit,
and occasionally, this micro
processor may malfunction
and need to be reset. This
can be done by pressing
RESET button with a pen,
which will shut down and
restart the unit. Do not use
RESET function excessively.

RESET BUTTON

When controlling the computer
with Remote Control Unit of this
projector, connect USB port of
your personal computer to this
connector. (Refer to P12.)

USB CONNECTOR (Series B)

✽ Do not press this button.

This button is used for our
optional accessories.

Connect a monitor to
this terminal.
This terminal outputs a
computer input signal
(except Digital signal
input on DVI terminal).
(Refer to P12.)

MONITOR OUTPUT

TERMINAL

Connect computer output
(Digital / Analog DVI-I type),
Media Card Imager*, or Wireless
Imager* to this terminal. (Refer to
P12)
*optional accessories

VIDEO INPUT JACK

Connect the composite
video output from video
equipment to connect
this jack.

(Refer to P13.)

AUDIO OUTPUT JACK

Connect computer output
(Analog HDB 15-pin type) or
21-pin Scart (RGB) output
from video equipment to this
terminal. (Refer to P12, 13.)

COMPUTER INPUT 1

TERMINAL

COMPUTER IN 2

DVI - I

MCI / WI

R – AUDIO IN – L

COMPUTER IN 1

MONITOR OUT

(MONO)

Pb / Cb – Pr / Cr

Y –

VIDEO

AUDIO IN 1

AUDIO IN 2

AUDIO OUT

RESET

CONTROL PORT

S – VIDEO

USB

12

CONNECTING PROJECTOR

CONNECTING TO COMPUTER

IBM-compatible computer or Macintosh computer (VGA / SVGA / XGA / SXGA)

VGA Cable

Monitor Output

Desktop type Laptop type

Audio Speaker

(stereo)

Audio Amplifier

Control Cable
for Serial Port

Audio Cable

(stereo)

✽

Terminal

Serial port

PS/2 port

Audio Output

Audio Input

CONTROL PORT

AUDIO OUT

COMPUTER

AUDIO IN

COMPUTER IN 2 DVI-I

Use one of these Control
Cables corresponding with
the terminal of your
computer.

ADB port

Cables used for connection (✽ = Cable or adapter is not supplied with this projector.)

Control Cable

for PS/2 Port ✽

Control Cable

for ADB Port ✽

Audio
Cable

✽

(stereo)

NOTE :

When connecting the cable, the power
cords of both the projector and the external
equipment should be disconnected from
AC outlet. Turn the projector and
peripheral equipment on before the
computer is switched on.

USB port

MAC Adapter ✽

Set slide switches
according to the
chart below.

• VGA Cable (HDB 15 pin)

• Control Cable for SERIAL Port

• DVI-Digital Cable (for Single Link T.M.D.S.)

✽

• Control Cable for PS2 Port ✽, or ADB Port ✽

• USB Cable

• MAC Adapter (When connecting to Macintosh computer)

✽

• DVI/VGA Adapter

• Audio Cables {Mini Plug (stereo) x 2}

✽

External Audio Equipment

Terminals

of the Projector

Terminal Terminal

VGA
Cable

✽

Monitor Input

USB

MONITOR OUT

Set switches as shown in the table
below depending on RESOLU­TION MODE that you want to use
before you turn on projector and
computer.

◆ MAC ADAPTER (Not supplied)

USB
Cable

COMPUTER IN 2 DVI-I

DVI Cable ✽

DVI/VGA
Adapter

COMPUTER IN 1

COMPUTER IN 2

DVI - I

MCI / WI

COMPUTER IN 1

MONITOR OUT

R – AUDIO IN – L

Pb / Cb – Pr / Cr

Y –

AUDIO IN 1

AUDIO IN 2

AUDIO OUT

(MONO)

VIDEO

RESET

CONTROL PORT

S – VIDEO

USB

13" MODE (640 x 480)
16" MODE (832 x 624)
19" MODE (1024 x 768)

1234 56

ON ON
ON ON

OFF OFF OFF OFF

ON

OFF

OFFON ON
OFFOFF OFF OFF

ON

2 3 4 5 6

1

OFF OFF OFF

OFF OFFON ONON ON21" MODE (1152 x 870)

DIP

13

CONNECTING PROJECTOR

CONNECTING TO VIDEO EQUIPMENT

Video Source (example)

Video Cassette Recorder Video Disc Player

Video Cable
(RCA x 1) ✽

S-VIDEO
Cable ✽

Audio Amplifier

Audio Speaker

(stereo)

Audio Cable
(Stereo)

✽

Terminals

of the Projector

Use any of VIDEO jack, S-VIDEO
jack, or Y-Pb/Cb-Pr/Cr jacks.

• When both VIDEO jack and S-

VIDEO jack are connected, S­VIDEO jack has priority over
VIDEO jack.

• When both Y-Pb/Cb-Pr/Cr jacks

and S-VIDEO jack are connected,
Y-Pb/Cb-Pr/Cr jacks has priority
over S-VIDEO jack.

S-VIDEO Output

Audio Input

Cables used for connection (✽ = Cable is not supplied with this projector.)

• Video Cable (RCA x 1 or RCA x 3)

✽ • Audio Cable {Mini Plug (stereo)} ✽

• S-VIDEO Cable ✽ • Scart Cable ✽

• Audio Cable (RCA x 2) ✽

NOTE :
When connecting the cable, the power
cords of both the projector and the external
equipment should be disconnected from
AC outlet.

Audio Output

(R, L)

Audio Cable
(RCA x 2) ✽

External Audio Equipment

AUDIO IN

S-VIDEO

Y - Pb/Cb - Pr/Cr

VIDEO

AUDIO OUT

Component video output equipment.

(such as DVD player or high-definition TV source.)

Composite

Video Output

Component Video Output

(Y, Pb/Cb, Pr/Cr)

Video Cable
(RCA x 3) ✽

RGB Scart

21-pin Output

Scart Cable

✽

COMPUTER IN 1

COMPUTER IN 2

DVI - I

R – AUDIO IN – L

MCI / WI

COMPUTER IN 1

MONITOR OUT

(MONO)

Pb / Cb – Pr / Cr

Y –

AUDIO IN 1

RESET

AUDIO IN 2

CONTROL PORT

AUDIO OUT

VIDEO

S – VIDEO

USB

14

BEFORE OPERATION

FOCUS BUTTON

Used to adjust focus. (P20)

AUTO PC ADJ. BUTTON

Use to operate AUTO PC
Adjustment function. (P25)

KEYSTONE BUTTON

Used to correct keystone
distortion. (P20, 36)

IMAGE BUTTON

Used to select image
level. (P28, 33)

OPERATION OF REMOTE CONTROL

ALL-OFF SWITCH

Left Side

When using Remote Control Unit,
turn this switch to “ON.” And turn it
to “ALL OFF” when it is not used.

This Remote Control Unit emits a laser beam as laser pointer function from Laser Light Window. When LASER button is
pressed, laser light goes on. And when LASER button is being pressed for more than 1 minute or LASER button is released,
light goes off. LASER POINTER INDICATOR lights RED and Laser is emitted with RED light to indicate laser beam is being
emitted.
Laser emitted is a class

II laser; therefore, do not look into Laser Light Window or shine laser beam on yourself or other

people. Three marks below are caution labels for laser beam.
CAUTION : Use of controls, adjustments or performance of procedures other than those specified herein may result

hazardous radiation exposure.

Laser Light Window

LASER POINTER FUNCTION

POWER ON-OFF BUTTON

Used to turn projector on or
off. (P19)

LASER BUTTON

Used to operate Laser Pointer
Function. Laser beam is
emitted while pressing this
button within 1 minute.
When using this Laser Pointer
for more than 1 minute,
release LASER button and
press it again.

Used as a PC mouse in
Wireless Mouse Operation.
(P40)

MOUSE POINTER

Used as a PC mouse in
Wireless Mouse Operation.
(P40)

RIGHT CLICK BUTTON

Lights red while laser beam
is emitted from Laser Light
Window.
Lights green when drag ON
position. (P40)

LASER POINTER (Drag ON)

INDICATOR

LASER POINTER INDICATOR

LENS SHIFT BUTTON

Used to select LENS
SHIFT function. (P20)

MUTE BUTTON

Used to mute sound. (P21)

DRAG ON/OFF BUTTON

Used to select drag ON/OFF
position. (P40)

Used as a PC mouse in
Wireless Mouse Operation.
Press this button and the
mouse pointer button to drag
a selected screen object.
(P40)

LEFT CLICK BUTTON

INSIDE THE BATTERY
COMPARTMENT BOX

This remote control provide the DIP
switches into the battery compartment
box.
Slide the SW4 (LASER ON/OFF
switch) to "OFF" position. The laser
pointer function is not operated.
Set switches 1-3 as shown in table
below depending on Code No. that you
want to select remote control code.
(Refer to P37.)

These caution labels are put on remote control.

ON

ALL OFF

DIP SWITCH SETTING

SW4 ........ LASER ON/OFF

SW1 SW2 SW3 Code No.

4

321

ON

ON
ON
OFF
OFF
ON
ON
OFF
OFF OFF

Code 1ON ON Code 1ON
Code 2ON OFF
Code 3ON ON
Code 4ON OFF
Code 5OFF ON
Code 6OFF OFF
Code 7OFF ON
Code 8OFF

LOCK

D.ZOOM

MUTE

VOLUME

MENU

ZOOM

FOCUS

AUTO PC

FREEZE

-

SELECT

LASER

P-TIMER

LENS

ON-OFF

NO SHOW

IMAGE

VOLUME

+

KEYSTONE

COMPUTER 1

COMPUTER 2

VIDEO

15

BEFORE OPERATION

To insure safe operation, please observe following precautions :

● Use (2) AA, UM3 or R06 type alkaline batteries.

● Replace two batteries at same time.

● Do not use a new battery with an used battery.

● Avoid contact with water or liquid.

● Do not expose Remote Control Unit to moisture, or heat.

● Do not drop Remote Control Unit.

● If a battery has leaked on Remote Control Unit, carefully wipe case clean and install new batteries.

● Danger of explosion if battery is incorrectly replaced.

● Dispose of used batteries according to batteries manufacturers instructions and local rules.

Press lid down­ward and slide it.

Remove battery
compartment lid.

Slide batteries into
compartment.

Replace compartment lid.

Two AA size batteries

For correct polarity (+ and
–), be sure battery
terminals are in contact
with pins in compartment.

Remote Control Batteries Installation

1 2 3

Operating Range

Point Remote Control Unit toward
projector (Receiver Window)
whenever pressing any button.
Maximum operating range for
Remote Control Unit is about 16.4’
(5m) and 60° in front and rear of a
projector.

16.4’
(5 m)

60°

16.4’
(5 m)

Used to operate P­TIMER function. (P21)

P-TIMER BUTTON

Used to adjust zoom. (P20)

ZOOM BUTTON

NO SHOW BUTTON

Used to turn picture into
black image. (P21)

D.ZOOM BUTTON

Used to select DIGITAL
ZOOM +/– mode and
resize image. (P30)

FREEZE BUTTON

Used to freeze picture. (P21)

60°

MENU BUTTON

Used to select MENU
operation. (P17, 18)

COMPUTER 1 BUTTON

Used to select input
source (COMPUTER 1).
(P22)

SELECT BUTTON

Used to execute item
selected, or to expand or
compress image in
DIGITAL ZOOM +/- mode.
(P30)

POINT (VOLUME +/-)

BUTTONS

Used to select an item or
adjust value in ON-SCREEN
MENU. They are also used
to pan image in DIGITAL
ZOOM +/- mode. (P30)
POINT LEFT/RIGHT buttons
are also used as VOLUME
+/- buttons. (P21)

COMPUTER 2 BUTTON

Used to select input
source (COMPUTER 2).
(P22, 31)

VIDEO BUTTON

Used to select input
source (VIDEO). (P31)

LOCK

VOLUME

D.ZOOM

MUTE

MENU

ZOOM

FOCUS

AUTO PC

FREEZE

-

SELECT

LASER

P-TIMER

LENS

ON-OFF

NO SHOW

IMAGE

VOLUME

+

KEYSTONE

COMPUTER 1

COMPUTER 2

VIDEO