Christie 4K40-RGB User Manual

User Guide

020-102958-04

4K40-RGB

D4K40-RGB, Roadie 4K40-RGB

NOTICES

Cop

All brand names and product names are trademarks, registered trademarks or trade names of their respective holders.

GENERAL

Every effort has been made to ensure accuracy, however in some cases changes in the products or availability could occur which may not be reflected in this document. Christie reserves the right to make changes to specifications at any time without notice. Performance specifications are typical, but may vary depending on conditions beyond Christie's control such as maintenance of the product in proper working conditions. Performance specifications are based on information available at the time of printing. Christie makes no warranty of any kind with regard to this material, including, but not limited to, implied warranties of fitness for a particular purpose. Christie will not be liable for errors contained herein or for incidental or consequential damages in connection with the performance or use of this material. Manufacturing facilities in Canada and China are ISO 9001 certified. Manufacturing facilities in Canada are also ISO 14001 certified.

WARRANTY

Products are warranted under Christie’s standard limited warranty, the complete details of which are available by contacting your Christie dealer or Christie. In addition to the other limitations that may be specified in Christie’s standard limited warranty and, to the extent relevant or applicable to your product, the warranty does not cover:

Problems or damage occurring during shipment, in either direction.

Problems or damage caused by combination of a product with non-Christie equipment, such as distribution systems, cameras, DVD players, etc., or use

of a product with any non-Christie interface device.

Problems or damage caused by misuse, improper power source, accident, fire, flood, lightning, earthquake, or other natural disaster.

Problems or damage caused by improper installation/alignment, or by equipment modification, if by other than Christie service personnel or a Christie

authorized repair service provider.

Use of third party product enclosures for environmental protection during outside use must be approved by Christie.

Problems or damage caused by use of a product on a motion platform or other movable device where such product has not been designed, modified or

approved by Christie for such use.

Except where the product is designed for outdoor use, problems or damage caused by use of the product outdoors unless such product is protected from

precipitation or other adverse weather or environmental conditions and the ambient temperature is within the recommended ambient temperature set forth in the specifications for such product.

Defects caused by normal wear and tear or otherwise due to normal aging of a product.

The warranty does not apply to any product where the serial number has been removed or obliterated. The warranty also does not apply to any product sold by a reseller to an end user outside of the country where the reseller is located unless (i) Christie has an office in the country where the end user is located or (ii) the required international warranty fee has been paid.

The warranty does not obligate Christie to provide any on site warranty service at the product site location.

PREVENTATIVE MAINTENANCE

Preventative maintenance is an important part of the continued and proper operation of your product. Failure to perform maintenance as required, and in accordance with the maintenance schedule specified by Christie, will void the warranty.

REGULATORY

The product has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the product is operated in a commercial environment. The product generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of the product in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at the user’s own expense. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment

CAN ICES-3 (A) / NMB-3 (A)

이 기기는 업무용(A급)으로 전자파적합등록을 한 기기이오니 판매자 또는 사용자는 이점을 주의하시기 바라며, 가정 외의 지역에서 사용하는 것을 목적으로 합니다.

ENVIRONMENTAL

The product is designed and manufactured with high-quality materials and components that can be recycled and reused. This symbol

and electronic equipment, at their end-of to local regulations. In the European Union, there are separate collection systems for used electrical and electronic products. Please help us to conserve the environment we live in!

-life, should be disposed of separately from regular waste. Please dispose of the product appropriately and according

means that electrical

Content

Introduction...................................................... 7

Models..........................................................7

Safet

y and warning guidelines........................................... 7

AC power precautions...............................................8

Laser safety precautions.............................................9

Light intensity hazard distance.........................................9

Product labels...................................................12

Product documentation...............................................14

Related documentation.............................................14

Technical support...................................................15

Projector overview..................................................15

Contact your dealer.................................................15

Key features......................................................15

List of components..................................................16

Display panel components.............................................16

IR remote keypad..................................................18

Adjusting the image............................................... 20

Selecting screen image orientation........................................20

Setting the image resize preset..........................................20

Adjusting lens settings...............................................20

Adjusting offset..................................................20

Resetting the lens to home position.....................................21

Aligning the image with lens zoom and focus............................... 21

Locking the lens motor.............................................21

Determining what lens warnings are displayed.............................. 21

Adjusting primary colors..............................................22

DMD color correction................................................ 22

Adjusting color by precise chromaticity values...............................22

Adjusting color by saturation......................................... 23

Signal color correction............................................... 23

Adjusting the color space............................................23

Adjusting color by temperature........................................23

Selecting the color correction mode.....................................24

ev. 1 (01-2020)

Content

Correcting for ambient light..........................................24

Setting the fr

ame delay...............................................24

Enabling film mode detect.............................................24

Adjusting the image sharpness..........................................25

Creating a seamless image with edge blending................................25

Adding edge blends to the projector.....................................25

Enabling basic edge blending.........................................25

Resetting edge blending............................................ 26

Blending black levels for multiple projectors..................................26

Enabling black level blending......................................... 26

Adjusting the black level blends........................................26

Resetting black level blending.........................................27

Geometry correction.................................................27

Enabling warping.................................................27

Correcting the shape of a keystoned image................................ 28

Configuring system settings.........................................30

Setting the date................................................... 30

Setting the time................................................... 30

Changing the splash screen............................................30

Determining the on-screen display position.................................. 30

Changing the language...............................................31

Changing the temperature units......................................... 31

Changing the user account password...................................... 31

Accessing the generated user account password............................. 31

Resuming projector operation after an AC power interruption.......................32

Keeping electronics on in standby mode.................................... 32

Enabling direct pass-through of HDMI, 3G, and DisplayPort input signals................32

Informing the source of signal preferences...................................33

Managing the light source.............................................33

Configuring the laser power settings using LiteLOC™ version 2.0................... 33

Configuring the laser power settings using LiteLOC™ version 1.0................... 34

Setting up 1D color uniformity.......................................... 35

Turning on the projector with low voltage....................................36

Configuring communications........................................37

Enabling projector communication........................................37

Setting the remote access level..........................................37

Communicating with 4K40-RGB through Art-Net...............................38

ev. 1 (01-2020)

Content

Art-Net channel listing............................................. 38

Index list for the input channel........................................40

orking with macros................................................ 42

Adding a macro..................................................42

Copying a macro.................................................43

Editing a macro..................................................43

Deleting a macro.................................................43

Configuring the GPIO................................................44

GPIO connector..................................................44

Setting up projector profiles.........................................46

Creating a new projector profile......................................... 46

Importing a projector profile............................................46

Restoring settings from a profile.........................................46

Renaming a projector profile............................................47

Exporting a projector profile to an external device..............................47

Deleting a projector profile.............................................47

Backing up, restoring, and upgrading files..............................48

Upgrading the 4K40-RGB software........................................48

Adding a software license to a projector.................................... 48

Exporting backup settings to an external device............................... 49

Importing a file from an external device to restore settings........................ 49

Restoring projector default settings.......................................49

Diagnostic tools ..................................................50

Viewing 4K40-RGB information..........................................50

Freezing an image..................................................50

Test patterns..................................................... 50

Selecting a test pattern.............................................50

Modifying grey level test pattern characteristics..............................51

Modifying ramp test pattern characteristics................................ 51

Modifying grid test pattern characteristics................................. 51

Enabling a specific test pattern color.....................................52

Selecting an engine test pattern....................................... 52

Viewing 4K40-RGB status............................................. 52

Running the 4K40-RGB interrogator.......................................52

Identifying where alarm and trap messages are sent............................ 53

Setting the SNMP read community string..................................53

ev. 1 (01-2020)

Content

Configuring traps.................................................53

Defining a tr

ap IP address...........................................53

Restoring factory default settings.........................................53

Regulatory...................................................... 55

Safety......................................................... 55

Electro-magnetic compatibility.......................................... 55

Emissions..................................................... 55

Immunity..................................................... 55

Environmental.................................................... 55

ev. 1 (01-2020)

Introduction

This manual is intended for professionally tr systems.

The illustrations in this document are for representation only and may not depict your projector model exactly

Only Christie qualified technicians who are knowledgeable about the hazards associated with highv

oltage, ultraviolet exposure, and the high temperatures generated by the projector are authorized to

assemble, install, and service the projector.

For complete 4K40-RGB product documentation and technical support, go to www.christiedigital.com.

ained operators of Christie high-brightness projection

Models

This guide applies to the following models.

• D4K40-RGB

• Roadie 4K40-RGB

Safety and warning guidelines

Read all safety and warning guidelines before installing or operating the projector.

This projector is intended for use in a non-cinema environment.

This projector must be operated in an environment that meets the operating range specification. Use only the attachments and/or accessories recommended by Christie. Use of others may result in the risk of fire, shock, or personal injury.

ev. 1 (01-2020)

Introduction

Warning! If not a

• This product must be operated in an environment that meets the operating range as specified in this document.

• Do not look directly into the lens when the light source is on. The extremely high brightness can cause permanent eye damage.

• EXTREME BRIGHTNESS! When accessing a restricted access location for product service or maintenance, avoid exposure to the product beam path by turning the product power off and disconnecting the product from AC power, or by shuttering the light source to avoid emissions from the front aperture.

• FIRE HAZARD! Keep hands, clothes, and all combustible material away from the concentrated light beam of the projector.

• Keep fingers and other body parts away from the moving parts in the product. Tie back long hair, and remove jewelry and loose clothing before manually adjusting the product.

• FIRE AND SHOCK HAZARD! Use only the attachments, accessories, tools, and replacement parts specified by Christie.

• Do not operate the product without a lens installed.

• Always use a lens plug when installing or moving the product. This prevents contaminants from entering the product.

• FIRE AND SHOCK HAZARD! Use only the attachments, accessories, tools, and replacement parts specified by Christie.

Caution! If not a

• TRIP OR FIRE HAZARD! Position all cables where they cannot contact hot surfaces, be pulled, be tripped over, or damaged by persons walking on or objects rolling over the cables.

voided, the following could result in death or serious injury.

voided, the following could result in minor or moderate injury.

AC power precautions

Read all safety and warning guidelines before connecting to AC power.

Warning! If not a

• SHOCK HAZARD! Only use the AC power cord provided with the product or recommended by Christie.

• FIRE AND SHOCK HAZARD! Do not attempt operation unless the power cord, power socket, and power plug meet the appropriate local rating standards.

• SHOCK HAZARD! Do not attempt operation if the AC supply is not within the specified voltage and current, as specified on the license label.

• SHOCK HAZARD! The AC power cord must be inserted into an outlet with grounding.

• SHOCK HAZARD! Disconnect the product from AC before installing, moving, servicing, cleaning, removing components, or opening any enclosure.

• Install the product near an easily accessible AC receptacle.

Caution! If not a

• FIRE HAZARD! Do not use a power cord, harness, or cable that appears damaged.

• FIRE OR SHOCK HAZARD! Do not overload power outlets and extension cords.

• SHOCK HAZARD! Power supply uses double pole/neutral fusing.

voided, the following could result in death or serious injury.

voided, the following could result in minor or moderate injury.

ev. 1 (01-2020)

Laser safety precautions

ead all safety and warning guidelines before operating the projector laser.

Warning! If not a

• PERMANENT/TEMPORARY BLINDNESS HAZARD! No direct exposure to the beam must be permitted. Class 1 Laser Product - Risk Group 3 according to IEC 60825-1:2014 and IEC 62471-5:2015.

• LASER RADIATION HAZARD! This projector has a built-in Class 4 laser module. Never attempt to disassemble or modify the laser module.

• Possible hazardous optical radiation emitted from this product. (Risk group 3)

• Only Christie qualified technicians who are knowledgeable about the hazards associated with laser use, high-voltage, and high temperatures generated by the product are authorized to assemble, install, and service the Christie Laser Projection System.

• Do not look directly into the lens when the light source is on. The extremely high brightness can cause permanent eye damage.

• Do not operate the product without all of its covers in place.

voided, the following could result in death or serious injury.

Light intensity hazard distance

Introduction

This projector has been classified as Risk Group 3 as per the IEC 62471-5:2015 standard due to possible hazardous optical and thermal r

Warning! If not a

• PERMANENT/TEMPORARY BLINDNESS HAZARD! No direct exposure to the beam must be permitted. Class 1 Laser Product - Risk Group 3 according to IEC 60825-1:2014 and IEC 62471-5:2015.

• PERMANENT/TEMPORARY BLINDNESS HAZARD! Operators must control access to the beam within the hazard distance or install the product at the height that prevents exposure of spectators' eyes within the hazard distance. The hazard zone must be no lower than 3.0 meters above the floor and the horizontal clearance to the hazard zone must be a minimum 2.5 meters.

• EXTREME BRIGHTNESS! Do not place reflective objects in the product light path.

voided, the following could result in serious injury.

adiation being emitted.

The following diagram and table show the zones for ocular and skin hazard distances:

ev. 1 (01-2020)

Introduction

• A—Hazard zone. The region of space where the projection light from the laser-illuminated projector is abo

ve emission limits for Risk Group 2. The light intensity may cause eye damage after a momentary or brief exposure (before a person can avert his or her eyes away from the light source). The light may cause skin burns to occur.

• B—Hazard distance. Operators must control access to the beam within the hazard distance or install the product preventing potential exposure of the spectators' eyes from being in the hazard distance.

• C—No access zone. Horizontal clearance of the no access zone must be a minimum of 2.5 meters.

• D—Vertical distance to hazard zone. The hazard zone must be no lower than 3.0 meters above the floor.

• E—Represents the top view of the projector.

• F—Represents the side view of the projector.

For US and international hazard distances based upon IEC 62471-5:2015, Photobiological Safety of Lamps and Lamp Systems – Part 5: Image Projectors.

Projection lens Part number Hazard distance

(m)

0.72:1 HB fixed 144-110103-XX 1.0

0.9:1 HB fixed 144-111014-XX 1.0

1.13-1.31:1 HB zoom 144-103105-XX 1.0

1.13-1.66:1 HB zoom 144-129103-XX 2.0

1.31-1.63:1 HB zoom 144-104106-XX 2.0

1.45-2.17:1 HB zoom 144-130105-XX 2.5

1.63-2.17:1 HB zoom 144-105107-XX 2.5

1.95-3.26:1 HB zoom 144-131106-XX 4.0

ev. 1 (01-2020)

Introduction

Projection lens Part number Hazard distance

(m)

1.99-2.71:1 HB zoom 144-106108-XX 3.0

2.71-3.89:1 HB zoom 144-107109-XX 4.5

3.89-5.43:1 HB zoom 144-108100-XX 6.5

0.72:1 UHC fixed 163-116109-XX 1.0

0.9:1 UHC fixed 163-117100-XX 1.0

1.13-1.66:1 UHC zoom 163-118101-XX 2.0

1.45-2.17:1 UHC zoom 163-119102-XX 2.5

1.95-3.26:1 UHC zoom 163-120103-XX 3.5

2.71-3.89:1 UHC zoom 163-121105-XX 4.6

3.89-5.43:1 UHC zoom 163-122106-XX 6.6

For Installations in the United States

The following must be in place for laser-illuminated projector installations in the United States:

• Any human access to the hazard zone, if applicable, must be restricted by barriers to enforce the no access zone.

• Permanent show installations containing Risk Group 3 laser-illuminated projectors must meet the following conditions:

• Installed by Christie or by Christie-authorized and trained installers.

Refer to the Laser Illuminated Projector - Class 1 Risk Group 3 Installation training (Course code: CF-LIPI-01) on the http://www.christieuniversity.com site.

• Performed according to instructions provided by Christie.

• Ensure the projection system is securely mounted or immobilized to prevent unintended movement or misalignment of the projections.

• A copy of the FDA variance approval letter must be with the operator or other responsible individual.

FDA variances can be found in the online training course–Laser Illuminated Projection - Class 1 Risk Group 3 Installation.

• Temporary show installations containing Risk Group 3 laser-illuminated projectors may be installed by Christie or sold or leased only to valid laser light show variance holders (laser light show manufacturers) for image projection applications. Such manufacturers may currently hold a valid variance for production of Class IIIb and IV laser light shows and/or for incorporation of the Risk Group 3 laser-illuminated projectors into their shows. This requirement applies also to dealers and distributors of these laser-illuminated projectors.

• For temporary installations, the FDA variance holder must maintain complete records of all show itineraries with dates, locations, operator name, and contact information clearly and completely identified.

• The Christie Laser Projection System Installation Checklist must be fully completed after the installation and sent to lasercompliance@christiedigital.com. A copy can remain on-site. This checklist can be found as a separate document in the accessory box with the manual.

ev. 1 (01-2020)

Introduction

• Certain US states have additional laser regulatory requirements. Go to www.christiedigital.com for additional regulatory requirements.

Product labels

Learn about the labels that ma

y be used on the product. Labels on your product may be yellow or

black and white.

General hazards

Hazard warnings also apply to accessories once they are installed in a Christie product that is connected to power.

Fire and Shock Hazard

To prevent fire or shock hazards, do not expose this product to rain or moisture.

Electrical Hazard

Do not alter the power plug, o

Do not remove the product enclosure.

Only Christie qualified technicians are authorized to service the product.

Risk of electric shock.

Do not remo

Only Christie qualified technicians are authorized to service the product.

General hazard.

Electric shock hazard. To avoid personal injury, disconnect all power sources before performing maintenance or service.

ve the product enclosure.

verload the power outlet, or use it with extension cords.

Electrocution hazard. To avoid personal injury, always disconnect all power sources before performing maintenance or service procedures.

Hot surface hazard. To avoid personal injury, allow the product to cool for the recommended cool down time before performing maintenance or service.

Burn hazard. To avoid personal injury, allow the product to cool for the recommended cool down time before performing maintenance or service.

Optical radiation hazard. To avoid personal injury, never look directly at the light source.

Moving parts hazard. To avoid personal injury, keep hands clear and loose clothing tied back.

ev. 1 (01-2020)

Fan hazard. To avoid personal injury, keep hands clear and loose clothing tied back. Always disconnect all power sources before performing maintenance or service procedures.

Voltage hazard. To avoid personal injury, always disconnect all power sources before performing maintenance or service procedures.

Not for household use.

Mandatory action

Disconnect all power sources before performing maintenance or service procedures.

Consult the service manual.

Introduction

Electrical labels

Laser labels

Indicates the presence of a protective earth ground.

CLASS 1 LASER PRODUCT IEC 60825-1

FDA laser variance (US projectors only)

This product conforms with performance standards for laser products under 21 CFR P characteristics authorized by Variance Number 2018-V-3898 effective on November 21, 2018.

art 1040 except with respect to those

ev. 1 (01-2020)

Indicates a light hazard. Do not look directly into the lens. The extreme high brightness can cause permanent ey Laser Product - Risk Group 3 according to IEC 60825-1: 2014 and IEC 62471-5:2015

Indicates Class 4 laser radiation when open. Avoid eye or skin exposure to direct or scattered r

Product documentation

Introduction

e damage. Class 1

adiation.

or installation, setup, and user information, see the product documentation available on the Christie

website. Read all instructions before using or servicing this product.

D4K40-RGB and Roadie 4K40-RGB

1. Access the documentation from the Christie website:

• Go to this URL: http://bit.ly/2NIBz7a or

https://www.christiedigital.com/en-us/business/products/projectors/3-chip-dlp.

• Scan the QR code using a QR code reader app on a smartphone or tablet.

2. On the product page, select the model and switch to the Downloads tab

Technical support

echnical support for Christie products is available at:

• North and South America: +1-800-221-8025 or Support.Americas@christiedigital.com

• Europe, Middle East, and Africa: +44 (0) 1189 778111 or Support.EMEA@christiedigital.com

• Asia Pacific: +65 6877-8737 or Support.APAC@christiedigital.com

Projector overview

Learn about the 4K40-RGB projector.

4K40-RGB is a professional quality, easy-to-use 3DLP® RGB laser projector. The high-brightness 4K40RGB is designed to meet the special demands found in large venues, live events, and high-usage environments. With reliable Christie RealLaser™ illumination integrated in a rugged chassis and ultrafast processing of Christie TruLife™ electronics, the 4K40-RGB is the go-to solution for demanding, large venue events and applications.

Contact your dealer

Record the information about your projector and keep this information with your records to assist with the servicing of your projector. If you encounter a problem with your Christie projector, contact your dealer.

Purchase record

Dealer:

Dealer or Christie Sales/Service contact phone number:

Projector serial number:

The serial number can be found on the license label located on the displa

Purchase date:

Installation date:

Ethernet settings

Default gateway

Projector IP address

Subnet mask

y panel

Key features

Understand the important features of the projector

• Long lasting, reliable Christie RealLaser™ RGB laser illumination

• Compact form with direct-coupled laser source integrated into the projector chassis

• LiteLOC™ color lock feature for constant image brightness and color

ev. 1 (01-2020)

• Omnidirectional operation for unrestricted design and installation flexibility

•

Christie TruLife™ electronics for ultra-high resolution, high frame rate video up to 120 frames per second

• Christie Terra input card integrates into SDVoE networks

• Compatible with most Christie Boxer lenses

• Full-color LCD display to provide information at-a-glance

• Integrated keypad control interface

List of components

Verify all components were received with the projector.

• Power cord

• IR remote keypad

• Network cable

• Tools

• Fiber optic support

• Laser illumination source interlock jumper for J33 harness (P/N: 001-114198-XX)

• Fiber connector safety cover

Introduction

Display panel components

Identify the main components of the display panel (also known as the home page).

ID Component Description

A Projector Information Provides information about the projector such as the projector

B Projector and Component

Controls

name, serial number

Indicates the states of the projector and its components.

, software version, and projector ID.

ev. 1 (01-2020)

Introduction

ID Component Description

C Power and Temperature Indicates the light source mode, power mode, and intake

temper

ature.

D Status Contains information about the health of the projector including

the number of warnings and errors.

Provides access to the status system.

E IP Settings Displays the IP address and subnet values.

Provides access to changing the IP settings.

F Test Pattern Displays the currently selected test pattern. If no test pattern is

selected, Off is displayed.

Provides access to the list of test patterns.

G Input Displays the signal for the currently selected input.

Provides access to the list of input signals.

ev. 1 (01-2020)

IR remote keypad

Introduction

The IR remote k

eypad controls the projector by way of wireless communications from a battery-

powered infrared (IR) transmitter.

Button Description

A Powers on the projector light source.

B Opens the aspect ratio dialog.

ev. 1 (01-2020)

+ 40 hidden pages