Christie 4000, HD4, HD2, HD7 User Manual

Mirage S+/HD, Matrix S+/HD,

Christie HD/DS+/DW, DLV

USER MANUAL

020-100001-05

China RoHS Compliance Information

关于中国《电子信息产品污染控制管理办法》的说明

• Environmentally Friendly Use Period

环保使用期限

The year number in the centre of the label indicates the Environmentally Friendly Use Period, which is required to mark on the electronic information product sold in China according to the China RoHS regulations.

本标志中表示的年数是根据《电子信息产品污染控制管理办法》（2006年2月28日）以及《电子信息产品污染控制标识要求》（2006年11月6日）制定的、适用于在中华人民共和国境内销售的电子信息产品的环保使用期限。

• Material Concentration Values Table 有毒有害物质含量表

Part Name

部件名称

铅

（Pb）汞（Hg）镉（Cd）

Low voltage

power supply

(LVPS)

AC relay

Ballast 镇流器

TIPM PCB

Built-in keypad

Three-chip panel

driver

High Definition

Panel Driver

Dual slot

backplane

module

Lamp Contact

PCB

Blower/Fan

Sensor

Illumination optics

system

Projection Lens

Auxiliary optics

Mechanical

enclosure*

Software CD 软件光盘

Lamp

Battery

Note: O : indicates that the concentration value of the particular hazardous substance contained in all the homogeneous materials for this part, according to EIP-A, EIP-B, EIP-C, is below the stipulated levels in China SJ/T11363-2006. 表示该有毒有害物质在该部件所有均质材料中的含量均在SJ/T11363-2006规定的限量要求以下。 X: indicates that the concentration value of the particular hazardous substance contained in all the homogeneous materials for this part, according to EIP-A, EIP-B, EIP-C, may be above the stipulated levels in China SJ/T11363-2006. 表示该有毒有害物质至少在该部件的某一均质材料中的含量可能超出SJ/T11363-2006规定的限量要求。 * This part uses metallic alloys, which may contain Lead. 因该部件使用金属合金材料，故可能含有铅。

低压电源

继电器

TIPM电路板

控制键盘

三芯驱动板

高清晰度驱动板

双槽底板模块

灯连接板

吹风机/风扇

传感器

照明光学系统

投影镜头

辅助光学器件

机械附件

灯泡电池

X O O O O X

X O O O O O X O O O O X X O O O O O X O O O O O X O O O O O

X O O O O O

O O O O O O O O O O O O X O X O O O

X O X O O O X O X O O O X O O O O O

O O O O O O X O X O O O O O O O O O

Material Concentration

(有毒有害物质或元素)

六价铬

(Cr 6+）

多溴联苯（PBB）

多溴二联苯醚

（PBDE）

Mirage S+/HD, Matrix S+/HD, Christie HD/DS+/DW, DLV User Manual i

020-100001-05 Rev. 1 (12-2008)

1 INTRODUCTION

2 INSTALLATION &

SETUP

3 OPERATION

4 MAINTENANCE

5 TROUBLESHOOTING

6 SPECIFICATIONS

APPENDICES

Table of Contents

1.1 Projector Overview ......................................................................................... 1-1

1.2 Components..................................................................................................... 1-3

1.3 Purchase Record and Servicing ....................................................................... 1-4

2.1 Quick Setup ..................................................................................................... 2-1

2.2 Installation Considerations .............................................................................. 2-3

2.3 Connecting Sources ....................................................................................... 2-12

2.4 Connecting Communications ........................................................................ 2-15

2.5 System Integration – GPIO Connector .......................................................... 2-19

2.6 Power Connection ......................................................................................... 2-19

3.1 About the Projector ....................................................................................... 3-1

3.2 Using the Remote or Built-in Keypad ............................................................. 3-3

3.3 Navigating the Menus ................................................................................... 3-10

3.4 Using Inputs and Channels ............................................................................ 3-14

3.5 Adjusting the Image ...................................................................................... 3-19

3.6 Adjusting System Parameters and Advanced Controls ................................. 3-39

3.7 Working with PIP and Seamless Switching .................................................. 3-53

3.8 Working with the Lamp ............................................................................... 3-56

3.9 Status Menu ................................................................................................. 3-60

3.10 Using Multiple Projectors ............................................................................. 3-60

3.11 Remote Control of the Projector .................................................................. 3-71

3.12 Error Conditions ............................................................................................ 3-71

4.1 Warnings and Safety Guidelines ..................................................................... 4-1

4.2 Cleaning and Maintenance Guide ................................................................... 4-4

4.3 Replacing Remote Batteries ............................................................................ 4-5

4.4 Lamp and Filter Replacement ......................................................................... 4-5

4.5 Replacing the Projection Lens ....................................................................... 4-11

5.1 Displays ........................................................................................................... 5-1

5.2 Lamp .............................................................................................................. 5-3

5.3 Ethernet ........................................................................................................... 5-3

5.4 3D Sync Input ................................................................................................. 5-4

6.1 Specifications .................................................................................................. 6-1

Appendix A: Glossary ............................................................................................... A-1

Appendix B: Keypad Reference ................................................................................. B-1

Appendix C: Serial Communications ......................................................................... C-1

Appendix D: Throw Distance .................................................................................... D-1

Appendix E: System Integration ................................................................................ E-1

Appendix F: Optional Input Modules ......................................................................... F-1

Appendix G: Index .................................................................................................... G-1

NOTE: Due to continuing research, all information in this manual is subject to change without notice.

Mirage S+/HD, Matrix S+/HD, Christie HD/DS+/DW, DLV User Manual iii

020-100001-05 Rev. 1 (12-2008)

1.1 Projector Overview

Section 1

Introduction

The Mirage S+/HD, Matrix S+/HD, Christie DH/DS/DW, DLV User Manual supports software v1.6g or higher. The projectors listed below are all professional 3-chip projectors, based on nextgeneration Digital Light Processing™ (DLP™) technology by Texas Instruments™ to deliver high quality, crisp, clean images.

Mirage S+3K/6K/8K and Mirage HD3/6/8 projectors provide a powerful combination of SXGA+ and HD + resolutions, high brightness and high contrast ratios to produce flawless, realistic three-dimensional graphic images for simulation, virtual reality and other stereographic related applications.

Additional reliable and compact projectors are the Matrix S+2K/5K/HD2/HD4/HD7, Matrix 4000. With their purpose built simulation features such as RGB color matching, and gamma controls, it can be used to simulate any application.

The DLV1400-DX and DLV1920-DX are designed for the demands of 24/7 control room applications and provide long-term reliability and performance.

This guide applies to the following projector models:

Mirage S+3K

Mirage S+6K

Mirage S+8K

Mirage HD3

Mirage HD6

Mirage HD8

Matrix S+2K

Matrix S+5K

Matrix HD2

Matrix HD4

Matrix HD7

Matrix 4000

DLV1400-DX

DLV1920-DX

Christie DS+6K

Christie DS+8K

Christie DS+5Kc

Christie HD3K

Christie HD6K

Christie HD8K

Christie HD2Kc

Christie HD5Kc

Christie HD7Kc

Christie DW5K

Christie DW8K

Christie DW6Kc

Christie DW4Kc

Mirage S+/HD, Matrix S+/HD, Christie HD/DS+/DW, DLV User Manual 1-1

020-100001-05 Rev. 1 (12-2008)

Section 1: Introduction

Main Features 

• Native SXGA+, HD or HD2 resolution (model dependant) with all others fully

scaleable

• Internal scaling of stereo signals (Mirage models)

• 10-bit video processing

• Built-in multi-standard video decoder

• Display of NTSC, PAL and SECAM video input

• User replaceable Cermax

• LiteLOC

™

for constant brightness

• Intelligent Lens System (ILS

Xenon lamp

™

) to save and restore lens settings

• Motorized lens mount for all models

• Auto-setup feature

• Integrated ChristieNET™

• Networking ability through RS232 and RS422 connectors

• Status LED display on built-in keypad for easy projector status monitoring

• Control with IR, wired or built-in keypad

• Two input slots for Optional Input Modules

Refer to Section 6 for a complete list of Specifications including Brightness and Contrast and Optional Input Modules

Inputs 

There are two different types of input face plate configurations (model dependant). See Figure 1.1 & 1.2. These configurations may include the following inputs:

• One analog RGBHV/YPbPr input with five BNCs

• One DVI-I input for either digital RGB/YCrCb or analog RGB/YPbPr signals

• One analog composite-video input

• One analog S-video input

• Built-in multi-standard video decoder (NTSC, NTSC 4.43, PAL, PAL-M, PAL-

N, PAL-60 AND SECAM)

• One Dual SD/HD-SDI module (standard on Christie HD models only)

• Compatible with all currently used HDTV formats

For simplicity, this manual refers to the configuration in Figure 1.1 only.

Figure 1.1

1-2 Mirage S+/HD, Matrix S+/HD, Christie HD/DS+/DW, DLV User Manual 020-100001-05 Rev. 1 (12-2008)

Section 1: Introduction



Figure 1.2

How the projector works 

1.2 Components

Lamp Type Model Name Resolution ChristieTWIS

500W Models DLV1400-DX SXGA+ Optional

1000W Models DW5K, 4Kc HD2 Optional

1200W Models DW8K, DW6Kc HD2 Optional

NOTE: Kc models include the same features, but are color corrected to film color standards.

The projector accepts data/graphics and video input signals for projection onto front or rear flat screens. High brightness light is generated by an internal Xenon lamp then modulated by three Digital Micro-mirror Device (DMD) panels that provide digitized red, green or blue color information. Light from the “on” pixels of each panel is reflected, converged and then projected to the screen through a single front lens, where all pixels are perfectly superimposed as a sharp full-color image (2D or 3D for Mirage models only).

The following listed items are shipped with your projector. Ensure you have received all these items before using your projector.

• User Manual

• IR remote keypad (includes two, 1.5V AA batteries and a mini-stereo cable for

conversion to wired)

• Line cord

• Stereo 3D Cable (Mirage only)

• Warranty Card

3D Motorized Lens

Mount



DLV1920-DX HD Optional Christie HD3K HD Optional Christie HD2Kc HD Optional Mirage S+3K SXGA+ Optional Mirage HD3 HD Optional Matrix S+2K SXGA+ Matrix HD2 HD

Christie DS+6K/5Kc SXGA+ Optional Christie HD6K/5Kc HD Optional Mirage S+6K SXGA+ Optional Mirage HD6 HD Optional Matrix S+5K SXGA+ Matrix HD4 HD

Matrix 4000 SXGA+

Christie DS+8K SXGA+ Optional Christie HD8K/7Kc HD Optional Mirage S+8K SXGA+ Optional Mirage HD8 HD Optional Matrix HD7 HD

   

  

 

  

 

  



 





 



Mirage S+/HD, Matrix S+/HD, Christie HD/DS+/DW, DLV User Manual 1-3

020-100001-05 Rev. 1 (12-2008)

Section 1: Introduction

Whether the projector is under warranty or the warranty has expired, Christie’s highly

1.3 Purchase Record and Warranty Registration

trained and extensive factory and dealer service network is always available to quickly diagnose and correct projector malfunctions. Service manuals and updates are available to service technicians for all projectors.

If you encounter any problems with the projector and require assistance, contact your dealer or Christie Digital Systems. Fill out the information in the table below and keep with your records for future reference.

Purchase Record

Dealer: Dealer Phone Number: Projector Serial Number: Purchase Date: Installation Date, if applicable:

NOTE: The serial number can be found on the license label, which is located at the back of the projector.

You can also register your product on-line by visiting www.christiedigital.com  Service and Support  Product Registration. This will keep you in touch with all

the latest product information, such as updates, technical bulletins, downloads and Christie newsletters.

For complete details on the warranty of your Christie product, please contact your Christie dealer.

1-4 Mirage S+/HD, Matrix S+/HD, Christie HD/DS+/DW, DLV User Manual 020-100001-05 Rev. 1 (12-2008)

2.1 Quick Setup

Section 2

Installation & Setup

The instructions provided here are for those that are familiar with the projector and wish to quickly set it up and use it temporarily. Refer to the remaining subsections of this manual for a more complete setup.

Step 1 

Ste

2 

Install a Projection Lens

The projection lens is shipped separately from the projector and must be installed prior to setting up the projector. Install the projection lens as described in 4.5 Replacing the Projection Lens.

Remove the lens plug from the lens opening in the projector before installing

the lens.

Remove the lens when shipping the projector and reuse the lens plug to

prevent dust and debris from entering and settling on the projector’s optical components.

Position the Projector

Place the projector on a sturdy, level surface and position it so that it is perpendicular to the screen at a suitable distance. In general, the further back the projector is positioned from the screen, the larger the image will be.

If required, you can level the projector by adjusting its three feet. With the projector positioned perpendicular to the screen the image will appear rectangular instead of keystoned.

For more detailed instructions on positioning the projector refer to Projector Position and Mounting later in this section.

Ste

Mirage S+/HD, Matrix S+/HD, Christie HD/DS+/DW, DLV User Manual 2-1

020-100001-05 Rev. 1 (12-2008)

3 

Connect a Source

Located at the back of the projector is the input panel where all source connections are made. Each input is clearly labeled for easy identification.

Using the appropriate cable(s), connect your source. Connect RGB and YPbPr sources to

INPUT 1 located in the upper right corner of the input panel. Use the DVI-I

connector at video to

NOTE: One of the available optional input modules can be installed at

INPUT 6

Refer to 2.3 Connecting Sources for more details on connecting a specific source.

INPUT 2 to connect analog or digital display signals. Connect composite

INPUT 3 and S-video to INPUT 4.

INPUT 5 or

for additional connections.

Section 2: Installation and Setup

Ste

4 

5 

Connect the Line Cord

The North American-rated line cord is provided with each projector. Ensure

that you are using a line cord, socket and power plug that meets the appropriate local rating standards.

Plug the line cord to the AC receptacle located on the right hand side of the projector and the three-pronged end into a grounded AC outlet. Ensure the socket outlet is installed near the equipment and is easily accessible. The input voltage to the projector must be capable of 100 – 240 VAC in 500W and 1000W models and 200240 VAC in 1200W models. (See also Section 6 – Specifications for complete details on all power requirements.)

Use the approved North American-rated line cord supplied with the projector. If you are connecting to an area outside of North America ensure an appropriately rated line cord is used.

Turn the Projector ON

Press the

POWER button on either the remote or built-in keypad to turn the projector on. Wait a few minutes to allow the projector to warm up. The LED status window displays an active pattern of segments to indicate the projector is changing its state from powered down to powered up. The message “On” appears in the display when the projector has completed its initialization and is ready for use.

Ste

6 

7 

Select a Source

Press one of the input keys on the remote or built-in keypad to select and display the image for the source you connected in Step 3.

Adjust Image

Adjust the more common image settings, such as Brightness, Contrast, Gamma, Focus, Zoom etc. using the direct keys on the IR remote.

You can also access the menu system and adjust these and other image settings by

pressing

on the remote.

2-2 Mirage S+/HD, Matrix S+/HD, Christie HD/DS+/DW, DLV User Manual 020-100001-05 Rev. 1 (12-2008)

Section 2: Installation and Setup

2.2 Installation Considerations

Proper installation of your projector will ensure the quality of your display. Whether you are installing a projector temporarily or permanently you should take the following into account to ensure your projector performs optimally.

Installation type 

Choose the installation type that best suits your needs: front or rear screen, floor mount or inverted mount.

Front Screen, Floor Mount Installation

ADVANTAGES CONSIDERATIONS

• Easy to set up

• Can be moved or changed quickly

• Easy to access

Front Screen, Inverted Mount (ceiling) Installation

ADVANTAGES CONSIDERATIONS

• Does not take up audience space

• Projector is unobtrusive

• Projector cannot be accidentally moved

Rear Screen, Floor Mount Installation

ADVANTAGES CONSIDERATIONS

• Projector is completely hidden

• Projector is easily accessed

• Usually good ambient light rejection

Rear Screen, Inverted Mount (ceiling) Installation

ADVANTAGES CONSIDERATIONS

• Projector is completely hidden

• Usually good ambient light rejection

Rear Screen, Floor Mount with Mirror

ADVANTAGES CONSIDERATIONS

• Projector is completely hidden

• Usually good ambient light rejection

• Requires less space behind screen than other

rear screen installations

• Shares floor space with audience

• Installation is more permanent

• It is more difficult to access the projector

• Requires separate room

• Installation cost is usually higher

• Requires separate room

• Installation cost is usually higher

• Requires separate room

• Installation cost is usually higher

Screen T

e 

Front Screen Installations

In front screen installations the projector and audience are positioned in front of the screen, which can be flat or curved.

Flat screens are most recommended with this projector. They offer a gain of about one with a viewing angle just less than 180°. This type of screen reflects incident light equally in all directions so the audience can see the display from various angles.

Curved screens have a gain greater than one with a viewing angle much less than 180°. This type of screen does not reflect incident light equally in all directions instead it is concentrated in a viewing cone. The audience sitting within the viewing cone area will see a brighter image than those sitting just outside this area.

Mirage S+/HD, Matrix S+/HD, Christie HD/DS+/DW, DLV User Manual 2-3

020-100001-05 Rev. 1 (12-2008)

Section 2: Installation and Setup

Rear screen installations

There are two basic types of rear screens: diffused and optical.

A diffused screen has a surface, which spreads the light striking it. Purely diffused screens have a gain of less than one. The main advantage of the diffused screen is its wide viewing angle, similar to that of a flat screen for front screen projection. This type of screen is suitable when a wide viewing angle is required but there is low ambient room lighting.

Optical screens take light from the projector and redirect it to increase the light intensity at the front of the screen. This reduces it in other areas. A viewing cone, similar to that of a curved front screen installation is created. This type of screen is better suited for brightly lit rooms where the audience is situated within the viewing cone.

Screen size

Choose a screen size, which is appropriate for your lens and application. Keep in mind that if the projector will be used to display text information, the image size must allow the audience to recognize all text clearly. The eye usually sees a letter clearly if eyeto-text distance is less than 150 times the height of the letter. Small text located too far from the eye will likely be illegible at a distance no matter how sharply and clearly it is displayed.

2-4 Mirage S+/HD, Matrix S+/HD, Christie HD/DS+/DW, DLV User Manual 020-100001-05 Rev. 1 (12-2008)

Section 2: Installation and Setup

To fill a screen with an image, the aspect ratio of the screen should be equal to the aspect ratio of the image (expressed as the ratio of its width to its height). Standard video from a VCR has a 4:3 or 1.33:1 aspect ratio. For example, to display a VCR output with a 4:3 aspect ratio onto a 10-foot (3m) high screen, the screen must be at least 13.3feet (4m) wide.

Ambient Li

hting 

Other Considerations 

Projector Position and  Mountin

The high brightness of this projector is well suited for locations where ambient lighting might be considered less than ideal for projection. A typical room with ceiling lights and windows rarely requires special attention. Contrast ratio in your images will be noticeably reduced only if light directly strikes the screen, such as when a shaft of light from a window or floodlight falls on the image. Images may then appear washed out and less vibrant.

In general, avoid or eliminate light sources directed at the screen.

Other considerations and tips that can help improve your installation:

• Keep the ambient temperature constant and below 35°C (95°F). Keep the

projector away from heating and/or air conditioning vents. Changes in temperature may cause drifts in the projector circuitry, which may affect performance.

• Keep the projector away from devices, which radiate electromagnetic energy such

as motors and transformers. Common sources of these include slide projectors, speakers, power amplifiers, elevators, etc.

Choose the best screen size for the application. Since more magnification reduces brightness, use a screen size appropriate for the venue but not larger than required. Installing a large screen in a small room is similar to watching television at a close range; too large a screen can overpower a room and interfere with the overall effect. A good rule of thumb is to be no closer than 1.5 times the width of the screen.

Throw distance

Throw distance is the distance measured from your projector’s front feet to the screen. This is an important calculation in any projector installation as it determines whether or not you have enough room to install your projector with a desired screen size and if your image will be of the right size for your screen.

You can quickly estimate the throw distance by taking the horizontal width of the screen and multiplying it by the lens throw ratio. The result of this calculation tells you roughly how far back the projector should be positioned from the screen in order to project a focused image large enough to fill the screen. For example, using a 0.73:1 lens, throw distance would roughly be 0.73 x screen width.

IMPORTANT: Once you determine the type of lens and screen size you’re going to use, calculate the precise throw distance using the formula or graphs located in Appendix D. Due to lens manufacturing tolerances for lens focal length, actual throw distance can vary ±5% between lenses described as having the same throw ratio.

Mirage S+/HD, Matrix S+/HD, Christie HD/DS+/DW, DLV User Manual 2-5

020-100001-05 Rev. 1 (12-2008)

Section 2: Installation and Setup

Vertical and horizontal position

The correct vertical and horizontal position of the projector in relation to the screen depends on the lens type and the screen size. Ideally, the projector should be positioned perpendicular to the screen. This way, the image will appear rectangular instead of keystoned (trapezoidal).

The vertical position of the image can be offset – that is moved above or below the optical axis (lens center) by adjusting the fully motorized lens mount with the keypad. The amount of vertical offset available depends directly on the lens installed in the projector and can be slightly limited if horizontal offset has been applied. Vertical offset can also be expressed as the percent of half the image height OR the number of pixels of shift from lens center. Refer to Figure 2.1 for some illustrated examples of vertical offset.

Table 2.1 along with Figure 2.2 show the maximum vertical offset of a lens or alternatively, how much of your projected image will appear above or below lens center if the maximum vertical offset is applied using that lens.

Table 2.1. Lens Offsets

Lens Type Offset Movement Max. Amount of Display

(All motorized

lenses)

SXGA+ Lenses 100% 50% 1050 pixels  or  100% 1050 pixels  or  75%

HD Lenses 119% 42% 1183 pixels  or  100% 1363 pixels  or  71%

 or   or 

Above or Below Lens Center

Max. Amount of Display

Right or Left of Lens Center

NOTES: 1) Offsets are subject to ±7% centering tolerance 2) % Offset = # pixels of offset / half panel resolution x 100.

2-6 Mirage S+/HD, Matrix S+/HD, Christie HD/DS+/DW, DLV User Manual 020-100001-05 Rev. 1 (12-2008)

Section 2: Installation and Setup

Figure 2.1. Vertical Offset Examples

Mirage S+/HD, Matrix S+/HD, Christie HD/DS+/DW, DLV User Manual 2-7

020-100001-05 Rev. 1 (12-2008)

Section 2: Installation and Setup

Figure 2.2. Lens Vertical Offsets

2-8 Mirage S+/HD, Matrix S+/HD, Christie HD/DS+/DW, DLV User Manual 020-100001-05 Rev. 1 (12-2008)

Section 2: Installation and Setup

The horizontal position of the image can be offset – that is moved to the left or right of lens center, by adjusting the fully motorized lens mount through software. The amount of horizontal offset available depends on the lens installed and if the image has already been vertically offset. Horizontal offset can also be expressed as the percent of half the image width – the number of pixels of shift to one side of lens center. Refer to Figure 2.3 for some illustrated examples of horizontal offset.

See also Table 2.1 along with Figure 2.4 which shows the maximum horizontal offset of a lens or alternatively, how much of your projected image will appear to one side of lens center if the maximum horizontal offset is applied using that lens.

Figure 2.3. Horizontal Offset Examples

Mirage S+/HD, Matrix S+/HD, Christie HD/DS+/DW, DLV User Manual 2-9

020-100001-05 Rev. 1 (12-2008)

Section 2: Installation and Setup

Figure 2.4. Lens Horizontal Offsets

2-10 Mirage S+/HD, Matrix S+/HD, Christie HD/DS+/DW, DLV User Manual 020-100001-05 Rev. 1 (12-2008)

Section 2: Installation and Setup

Mounting

There are several methods for mounting the projector. Depending on your chosen installation, one method may be more suitable than another. In typical front and rear screen installations the projector can be mounted to a secure and level surface, such as a table or cart. Carts are useful when the projector has to be moved during a presentation or from site to site. It is recommended you lock the wheels on a cart, when it’s in position, to prevent someone from accidentally moving it during a presentation.

CEILING MOUNT - The projector can also be inverted and suspended from the ceiling

using a specially designed ceiling mount fixture. This type of mounting is recommended for fixed installations and for those that want the projector out of plain view or have a limited amount of space for projector and audience. For more information, contact your dealer.

Use only the CHRISTIE approved ceiling mount kit designed for your

projector. Refer to the installation instructions and safety guidelines provided in the kit.

SPECIAL MOUNTING – The projector can be rotated (front-to-back) up to 360 degrees

and mounted without it affecting performance. However, the side-to-side tilt limit of the projector must not exceed ±15 degrees. This tilt limit is required to ensure optimal performance of the projector.

STACKING – An optional stacking frame is available for all models which allows

stacking up to a maximum of three projectors in an upright or inverted orientation. Refer to the instructions provided in the Stacking Frame kit (104-117101-01) for details regarding the assembly.

Adjusting projector height

You can modify the height of the projector to remedy a slightly uneven mounting surface by adjusting the two feet threaded into the bottom chassis. Turn each foot clock-wise or counter-clockwise until the project is level on all sides.

Folded Optics

In rear screen applications where space behind the projector is limited, a mirror may be used to fold the optical path. See Figure 2.5. The position of the projector and mirror must be accurately set – if considering this type of installation call your dealer for assistance.

Figure 2.5. Folded Optical Path

Mirage S+/HD, Matrix S+/HD, Christie HD/DS+/DW, DLV User Manual 2-11

020-100001-05 Rev. 1 (12-2008)

Section 2: Installation and Setup

Sources connect to the Input Panel located at the back of the projector. See Figure 2.6.

2.3 Connecting Sources

The upper right corner ( analog RGB source, or it can also be used for YPbPr signals or additional video sources. Just beside these BNCs, the DVI-I connector ( analog display signals from a computer. Connect analog composite video at or S-video at

INPUT 4 from devices such as VCRs, laser disc players or DVD players.

There are also several optional interfaces available for connecting other sources— these interfaces slide into the remaining unused option slot, and can be done while the projector is running.

INPUT 1) typically accepts an RGB signal from an external

INPUT 2) accepts digital or

INPUT 3

RGB Signals 

Figure 2.6. Input Panel

NOTES: 1) See Section 6 – Specifications for details regarding compatible inputs.

2) Use high quality shielded cables only for all connections.

INPUT 1 consists of five BNCs (connectors) for linking to a variety of sources. The

typical connection would be to an RGB source such as a PC, Mac, DEC, Sun, SGI and others. This projector supports multiple sync types with RGB signals: sync-on-green, composite sync, and separate H & V syncs.

NOTE: Depending on your source, you may need a custom adapter cable with BNC connectors at the projector end and a different type of connector at the other (such as a 15-pin "D" connector for some computer sources). Contact your dealer for details.

Connect the outputs to the

SYNC BNC input(s) first. Then connect the red, green and blue source

RED, GREEN, and BLUE BNCs on the INPUT 1 panel. If the source uses

sync-on-green, only the red, green, and blue connections are required. If the source provides a composite sync output, connect it to the

SYNC input labeled HOR/COMP. If

the source provides separate horizontal and vertical sync outputs, connect horizontal sync to the labeled

SYNC input labeled HOR/COMP and connect vertical sync to SYNC input

VERT. See Figure 2.7.

2-12 Mirage S+/HD, Matrix S+/HD, Christie HD/DS+/DW, DLV User Manual 020-100001-05 Rev. 1 (12-2008)

Section 2: Installation and Setup

YPbPr Signals 

(COMPONENT VIDEO)

Figure 2.7. Connecting RGB and Sync

NOTES: 1) If for some reason the projector fails to recognize a signal as an RGB signal, specify this Color Space option within the Image Settings menu. See 3.5 Adjusting the Image. 2) To connect YPbPr signals–such as from DVDs or analog HDTV sources–to

INPUT 1, use the red, green and blue BNCs as described in YPbPr Signals

(below).

Connect a YPbPr signal (component video) to INPUT 1 or INPUT 2 as shown in Figure

2.8.

NOTES: 1) If, for some reason, the projector fails to recognize a YPbPr signal, specify this Color Space option within the Image Settings menu. See 3.5, Adjusting

the Image. 2) Do not connect digital

. Install an appropriate optional module in INPUT 5 or INPUT 6 for this.

Figure 2.8. Connecting YPbPr sources

component signals (known as YCbCr) to INPUT

Mirage S+/HD, Matrix S+/HD, Christie HD/DS+/DW, DLV User Manual 2-13

020-100001-05 Rev. 1 (12-2008)

Section 2: Installation and Setup

Com

osite and S-Video 

DVI Di

ital Video 

INPUT 3 and INPUT 4 provide simultaneous connection of both a composite video

source (

INPUT 3) and an S-Video source (INPUT 4). See Figure 2.9.

Figure 2.9.Connecting Composite or S-Video sources

Use the DVI-I connector at INPUT 2 to connect either analog or digital video devices to the projector. When connecting devices that transmit an analog video signal such as VCRs, laptops, and PCs use the DVI cable provided with the projector. Plug the DVI-I (single link) connector end to the projector and the 15-pin VGA connector to the device.

tional Inputs 

Use a cable with DVI-I connectors at both ends to connect devices that transmit digital and analog video signals such as high-quality DVD players, satellite receiver and digital cable TVs.

NOTES: 1) To ensure true digital output from devices that transmit digital signals, connect to the DVI-I connector. 2) DVI loop through is not available unless you have the optional DVI Input Module installed at

INPUT 5 or INPUT 6.

Optional modules allow you to increase your total number of inputs and/or accommodate different signal types, whether analog or digital. Install in the areas labeled

INPUT 5 or INPUT 6. Options include:

• RGB 500 Input Module

• RGB 400 Active Loop Thru Input Module

• RGB 400 Buffered Amplifier Input Module

• PC250 Analog Input Module

• Serial Digital Input Module

• DVI Input Module (standard on Mirage HD models)

• Dual SD/HD-SDI Module (standard on Christie HD models)

NOTE: See Appendix F – Optional Input Modules for a brief description of each interface.

2-14 Mirage S+/HD, Matrix S+/HD, Christie HD/DS+/DW, DLV User Manual 020-100001-05 Rev. 1 (12-2008)

Section 2: Installation and Setup

2.4 Connecting Communications

As an alternative to the projector’s keypad or remote, you may wish to communicate with the projector using a PC or other controller. Such a device sends commands and receives feedback via serial links (RS232 and RS422), Ethernet or GPIO communications to the projector, all described below.

Remote Keypads 

Serial Port Connections 

As desired, direct the projector’s IR remote keypad towards the display screen or the projector’s IR sensors. Alternatively, connect a wired (tethered) version of the remote to the 3.5mm RCA jack labeled as

REMOTE on the projector’s input panel. Note that

response to a wired keypad must also be enabled in the Communications menu—see

3.6, Adjusting System Parameters and Advanced Controls for more information.

There are two types of serial ports available on the projector: RS232 and RS422. You can connect a device with a serial interface, such as a computer to either of these connectors (not both) and control the projector remotely by entering specific serial communication commands.

Connecting RS-232

The two nine-pin DIN connectors labeled RS232 IN and RS232 OUT on the input panel are dedicated to serial communication (see Figure 2.10). Using the appropriate serial communication cables (see Appendix C) connect the controlling source, such as a personal computer to the RS232 IN connector. Then set the baud rate to match that of the computer. Refer to Section 3 for details on changing the projector’s baud rate.

Figure 2.10. Connecting RS232

Connecting RS-422

If you wish to control the projector with a computer and or other controlling device with RS-422 capability, connect a RS-422 serial communication cable between the computer and the RS-422 port on the projector (see Figure 2.11). RS-422 is better suited for serial communication over long distances then is RS-232 communication.

Use the RS-422 port only if your device had RS-422 capability – always

consult the literature provided with your equipment before connecting. Connecting to the RS-422 port with incompatible equipment could damage your projector.

Mirage S+/HD, Matrix S+/HD, Christie HD/DS+/DW, DLV User Manual 2-15

020-100001-05 Rev. 1 (12-2008)

Section 2: Installation and Setup

Figure 2.11. Connecting RS422

Ethernet Communications 

Ethernet Communications

To add the projector to an existing Ethernet network with other equipment such as controllers and other projectors, connect standard CAT5 Ethernet cable between your Ethernet controller (or hub) and the Ethernet port on the side of the projector.

Connecting Multiple  Pro

ectors

Upon connection to an Ethernet network, the projector’s factory default IP address of

0.0.0.0.0 will automatically enable the DHCP function (if available on the network) to assign a new IP address that is valid and unique for that network. Or, if there is no DHCP function available on the network (or if a specific static IP address for the projector is preferred or required), you can set the address in the Ethernet Settings menu or via an ASCII serial command.

Regardless of how it is assigned, once a projector has a valid and unique address it will respond to commands sent to this address. To determine the projector’s current IP address, consult the Status or Communications menus.

Refer to Section 3 for further information about setting up and using a projector connected via Ethernet.

Log on to www.christiedigital.com for detailed information on ChristieNET™.

RS-232 NETWORK: If you want to connect multiple projectors in a network with serial

communication, connect the controlling source to the RS232 IN connector of the first projector in the network. Then take another serial communication cable and connect one end to the RS232 OUT connector and the other end to the RS232 IN connector of the next projector. Continue this pattern of connection with all projectors in the network. The last projector in the network will only have a connection to the RS232 IN connector. See Figure 2.12.

2-16 Mirage S+/HD, Matrix S+/HD, Christie HD/DS+/DW, DLV User Manual 020-100001-05 Rev. 1 (12-2008)

Section 2: Installation and Setup

Figure 2.12. RS232 Network

MIXED NETWORK: To control multiple projectors with a computer/controller having an

RS422 interface, first set them all to the same baud rate as your RS422 controller.

NOTE: You must enable this combination of RS422 and RS232 in the Communications menu. Set the “Network Routing” option to “RS232 and RS422 Joined”. See Section 3 for details.

Then chain the projectors together by connecting an (already connected to the computer/controller through the

RS232 port of the first projector

RS422 port) to an RS232

port on the next projector in the chain. Continue connecting projectors in this manner until you’ve reached the last projector in the chain, so that only the last projector has one unused

RS232 port. See Figure 2.13.

Figure 2.13. Mixed Network

Note that communication parameters such as baud rate must be set to match the particular controlling device before connecting as a network—refer to the documentation that came with your controlling device in order to determine the proper baud rate. See 3.6, Adjusting System Parameters and Advanced Controls if you need help changing the projector baud rate. In addition, set the Network Routing to “RS232 and RS422 Joined” if you want to reach all projectors.

NOTES: 1) To avoid damage, connect only properly wired serial communication cables. See Appendix C for details. 2) It is recommended that each RS232 communication cable be no more than 25 feet in length. Use high quality cables.

ETHERNET NETWORK SETUP: To add one or more projectors to an Ethernet network,

use standard CAT5 cable to connect each projector’s Ethernet port to a hub belonging to the network. A controller or PC must also be connected to the hub. See Figure 2.14.

Mirage S+/HD, Matrix S+/HD, Christie HD/DS+/DW, DLV User Manual 2-17

020-100001-05 Rev. 1 (12-2008)

Section 2: Installation and Setup

Figure 2.14. Ethernet Network

SETTING THE PROJECTOR’S IP ADDRESS: Upon connection to most Ethernet

networks, each projector’s factory default IP address of 0.0.0.0 triggers the network’s DHCP (Dynamic Host Configuration Protocol) server function to automatically assign an IP address that is valid and unique for use on that network. Depending on the network, this DHCP-assigned IP address usually remains stable for a single session, but may change with subsequent power-ups and logins. On some networks, the address will remain stable from session to session. In all cases, the projector’s IP address and port appear in the Status menu as well as the Ethernet Settings submenu. See Figure 2.15.

Figure 2.15. Setting the Projector’s IP Address

Note that if a projector’s IP address is anything other than 0.0.0.0 (shown as

000.000.000.000 in the Ethernet Settings menu) upon connection to an Ethernet network, or if DHCP is not available on the network, the automatic DHCP server function for supplying a valid and unique IP address to the projector is disabled. Instead, a specific and static IP address must be defined in projector memory—enter the new address in the Ethernet Settings submenu, or send to the projector via a serial command. The IP address will be in effect until it is changed again, or until the DHCP checkbox is re-enabled for use with a DHCP server on the network.

CHANGING THE PORT#: On some Ethernet networks, firewall restrictions may require

that the port number of the projector be changed from its default of 3002. If so, enter a new port number in the Ethernet Settings menu or include the new port# in an XIP serial command sent to the projector. It is highly recommended not to use a port# below 1024, as these ports are typically reserved for and used by common IP applications.

SUBNET MASK AND DEFAULT GATEWAY: The Subnet Mask and Default Gateway are

automatically assigned when DHCP is enabled. If a static IP is being used, it must be assigned before the subnet mask. The Default Gateway is an optional router device used to send and receive data outside the subnet.

2-18 Mirage S+/HD, Matrix S+/HD, Christie HD/DS+/DW, DLV User Manual 020-100001-05 Rev. 1 (12-2008)

Section 2: Installation and Setup

ArtNet INTERFACE SETTINGS: Refer to Section 3.6 – Adjusting System Parameters

and Advanced Control, System Configuration – Communication for additional

information about ArtNet settings.

arating Networks 

By default, communications originating from one type of serial controller—RS232 vs. RS422 vs. Ethernet—stay on the corresponding network path. A “Separate” setting indicates this separation for “Network Routing” in the Communications menu. If you are using an RS422 controller, for example, it will communicate only with the projector to which it is connected unless you change this setting to either “RS232 and RS422 Joined” or “All Joined”.

Communicating to  All Ports

To relay all messages to all ports—RS232, RS422, and Ethernet—set the “Network Routing” option in the Communications menu for each projector to “All Joined”. This configuration is useful if you are using a non-RS232 controller with the RS232 linking available between these projectors. For example, you may want to use both an RS422compatible controller and an Ethernet-connected PC for working with a network of projectors linked via their RS232 in/out ports.

2.5 System Integration GPIO Connector

Figure 2.16. Joining All Networks

To isolate just RS422 communications, select “RS232 and Ethernet Joined”. In Figure

2.16, only projector #3 will respond to the RS422 controller. To isolate just Ethernet communications, select “RS232 and RS422 Joined”—only projector #1 will respond via Ethernet.

The GPIO connector on the input panel can be used to provide a method of interfacing a wide range of external I/O devices to the projector.

Refer to Appendix E: System Integration for complete details on pin configuration and how to program the various pins on the connector.

Mirage S+/HD, Matrix S+/HD, Christie HD/DS+/DW, DLV User Manual 2-19

020-100001-05 Rev. 1 (12-2008)

Section 2: Installation and Setup

2.6 Power Connection

The North American rated line cord is provided with each projector. Ensure

that you are using a line cord, socket and power plug that meets the appropriate local rating standards.

Plug the line cord to the AC receptacle located at the back of the projector, below the input panel, and the three-pronged end into a grounded AC outlet. Ensure the socket outlet is installed near the equipment and is easily accessible. The input voltage to the projector must be capable of 100 – 240 VAC in 500W and 1000W models and 200240VAC in 1200W models. (See also Section 6 – Specifications for complete details on all power requirements.)

Use the approved North American-rated line cord supplied with the projector. If you are connecting to an area outside of North America ensure an appropriately line cord rated for the region of use is used.

Always power down the projector before unplugging the AC line cord. Wait 5-10 minutes for the main exhaust fan to turn off and for the lamp to cool sufficiently before unplugging the projector.

WARNINGS

Do not attempt operation if the AC supply and cord are not

within the specified voltage and power range.

Wait for the cooling fans to turn off before unplugging the

projector.

2-20 Mirage S+/HD, Matrix S+/HD, Christie HD/DS+/DW, DLV User Manual 020-100001-05 Rev. 1 (12-2008)

+ 152 hidden pages