Page 1
User Guide
©2019 Artsana USA, Inc. 6/19
For future use, STORE USER GUIDE
in location on bottom of base.
Booster Car Seat
www.chiccousa.com
IS0180E_01
Page 2
TABLE OF CONTENTS
If you have any problems with your Chicco Booster Seat,
or any questions regarding installation or use, please call:
Chicco Customer Service
1-877-424-4226
Please have Model and Serial Number available when you call.
These are located on a label on the bottom of the Booster Seat.
For future reference, fill in the information below. The information can be found on the label
on the bottom of the Child Restraint.
Model Number:
Serial Number:
Manufactured In:
Registration and Recall 2
Child Guidelines 4
Safe Use Checklist 6
Important Warnings 8
Best Practices 12
Need Help? 13
BOOSTER SEAT OVERVIEW
Booster Seat Components 14
High-Back Mode 16
Backless Mode 18
VEHICLE INFORMATION
Vehicle Seating Positions 20
Vehicle Seat Belts 22
What is LATCH? 24
ASSEMBLY INFORMATION
Assembly 26
HIGH-BACK MODE
Adjusting Backrest Height 32
Install High-Back Booster Seat 34
Securing Child in Booster Seat 38
BACKLESS MODE
Removing Backrest 46
Using Shoulder Belt Clip 50
Install Backless Booster Seat 52
Securing Child in Booster Seat 56
Adjusting Shoulder Belt Clip Height 58
SAFETY INFORMATION
Secure Child Checklist 62
Booster Seat Safe Use Checklist 64
ADDITIONAL INFORMATION
Installation on an Aircraft 66
Cup Holder 68
Release LATCH Connectors 70
Removing Fabric Covers 72
Cleaning and Maintenance 90
Page 3
REGISTRATION AND RECALL REGISTRATION AND RECALL
Please complete the Registration Card that came with
your Booster Seat and mail it promptly.
Child Restraints could be recalled for safety reasons. You must register this restraint to be reached in
a recall. Send your name, address, e-mail address if available, and the restraint’s model number and
manufacturing date to:
Artsana USA, Inc.
1826 William Penn Way
Lancaster, PA 17601
or call 1-877-424-4226
or register online at http://www.chiccousa.com/carseatregistration.aspx
For recall information, call the U.S. Government’s Vehicle Safety Hotline at
1-888-327-4236 (TTY: 1-800-424-9153), or go to http://www.NHTSA.gov.
PAGE INTENTIONALLY LEFT BLANK
2
3
Page 4
CHILD GUIDELINES CHILD GUIDELINES
This Booster Seat is designed for children who demonstrate an ability to sit
in a seat belt and meet the following requirements. ONLY use this Booster
Seat if the child meets the following requirements:
4
• Child is at least 4 years old.
• Child can sit relatively still, in the same seated position
throughout the car ride.
• Child can leave the shoulder and lap belt properly positioned
on their body, and can do this every time in the car.
• Weight is between 30 and 110 pounds (13.6 and 50 kg).
• Height is between 38-57 inches (97-145 cm).
YOUR CHILD’S SAFETY DEPENDS ON YOU! You MUST follow the
detailed instructions in this User Guide to ensure the steps in this User
Guide are performed correctly!
High-Back Mode
on page 16.
HIGH-BACK
30 lbs 40 lbs 100 lbs 110 lbs
(13.6 kg) (18 kg) (45.3 kg) (50 kg)
BACKLESS
Backless Mode
on page 18.
5
Page 5
SAFE USE CHECKLIST SAFE USE CHECKLIST
Make sure your child can sit in the seat properly and meets the
requirements listed in the “Child Guidelines” section on page 4:
Choose the appropriate Booster Seat configuration:
HIGH-BACK MODE requirements on page 16
BACKLESS MODE requirements on page 18
Select a safe seating location in your car:
Refer to the “Vehicle Seating Positions” section on page 20 and 21.
Secure your child:
Refer to the “Safety Information” section on page 62.
6
7
Page 6
IMPORTANT WARNINGS
IMPORTANT WARNINGS
8
WARNING
DEATH or SERIOUS INJURY CAN OCCUR
FAILURE TO FOLLOW THESE INSTRUCTIONS AND THE PRODUCT
LABELS CAN RESULT IN SERIOUS INJURY OR DEATH TO YOUR CHILD.
Take Time to Read This User Guide
• Carefully read and understand all instructions and warnings in this User Guide. Your child’s safety depends
on you knowing how to setup, install and use this Booster Seat properly.
• Before installing this Booster Seat in a vehicle, be sure to also check the vehicle owner’s manual for
information on proper installation.
• NEVER allow others to use this Booster Seat until they have read and understood all instructions in this
User Guide.
• This Booster Seat is not intended for use outside of the vehicle.
Make Sure Child Fits This Booster Seat
• Use ONLY with children who weigh between 30 lbs (13.6 kg) and 110 lbs (50 kg) and whose height is 38-57
inches (97 -145 cm). Determine the right installation setup for your child’s age, weight, height, and ability to sit
properly at all times.
WARNING
DEATH or SERIOUS INJURY CAN OCCUR
Install Child Restraint Correctly
• DO NOT PLACE THIS BOOSTER SEAT IN A VEHICLE SEATING LOCATION WITH A FRONTAL AIR
BAG, UNLESS THE AIR BAG CAN BE TURNED OFF. If the airbag inflates, it can cause serious injury or
death to your child. For vehicles with side air bags, refer to you vehicle owners manual for information on
your booster seat installation.
• ALWAYS install this Booster Seat in a back seat if possible.
According to accident statistics, children are safer when properly restrained in a rear seating
position rather than in the front seat.
• NEVER install in rear facing, side facing or on the back of a folded down vehicle seat.
• NEVER use this Booster Seat with only a Vehicle Lap Belt.
• Use ONLY the vehicle’s lap and shoulder belt system when restraining the child in this booster seat.
• To avoid injury to others, ALWAYS secure this Child Restraint with the vehicle’s Lap-Shoulder Belt when
unoccupied.
• DO NOT use this Booster Seat beyond the “Do Not Use After” date. Check manufacturer’s label on
underside of Booster Seat.
9
Page 7
IMPORTANT WARNINGS
IMPORTANT WARNINGS
10
WARNING
DEATH or SERIOUS INJURY CAN OCCUR
Secure Child Properly
• Position Lap-Shoulder Belt on your child. A loose or improperly positioned Lap-Shoulder Belt could cause
the child to be ejected in a sudden stop or crash, resulting in serious injury or death.
• Make sure vehicle Lap-Shoulder Belt is not loose. The belt must be kept snug across child’s thighs and
resting on the shoulder and across the center of the chest.
• NEVER use clothing or blankets that interfere with fastening or tightening the Lap-Shoulder Belt. An
unsecured child could be ejected in a sudden stop or crash!
• ALWAYS check to make sure the vehicle seat buckle is securely latched.
• NEVER leave your child unattended in the vehicle.
• Do not allow children to play in or around the Booster Seat.
WARNING
DEATH or SERIOUS INJURY CAN OCCUR
Check Condition of Restraint
• DO NOT use if the vehicle belts are cut, frayed or damaged.
• DO NOT use any accessories, pads or products not included with this Booster Seat, unless approved
by Chicco USA. Doing so will void the warranty of this Booster Seat.
• You MUST replace this Booster Seat if it has been involved in a crash, even if you cannot see visible
damage. A damaged Booster Seat may not protect your child in a future crash.
• Do not modify your Booster Seat.
• Do not use Booster Seat if any component is damaged, broken, or missing. Call 1-877-424-4226 to
find out if the damaged part or parts can be replaced.
11
Page 8
BEST PRACTICES
NEED HELP?
12
• Ensure all vehicle occupants are properly restrained before traveling.
Unrestrained occupants can be thrown around and may be seriously injured or
seriously injure other occupants in a sharp turn, sudden stop or crash.
• Do not leave loose objects, such as books, bags, etc., in the back of the vehicle.
In the event of a sharp turn, sudden stop, or crash, loose objects can be thrown
around and possibly cause serious injury to vehicle occupants.
• Cover the Booster Seat when the vehicle is parked in sunlight. Parts of a Booster
Seat can become very hot if left in the sun. Contact with these parts can burn
a child’s skin. Always check the surface of any metal or plastic parts before
putting your child in the Booster Seat.
• To avoid strangulation, do not allow children to play with vehicle seat belts. If
possible, move unused belts out of reach.
• Do not use anything to raise the Booster Seat off the vehicle seat such as a
noodle or towel. In a sharp turn, sudden stop, or crash, the Booster Seat could
slide and potentially cause serious injury.
• Never use a second-hand Booster Seat with an unknown history.
• Never use any accessories that are not included with this child restraint, unless
specifically approved by Chicco. For more information, go to www.chiccousa.
com.
Need Help Securing Your Booster Seat?
The following sources are available to help ensure your Booster Seat is
properly installed:
• Contact Chicco, USA by visiting our website at www.chiccousa.com or
calling our Customer Service 1-877-424-4226. Please have Model and
Serial Number available when you call. These are located on a label on
the bottom of the Booster Seat.
• Refer to your vehicle manual for Booster Seat installation tips.
• Contact a certified Child Passenger Safety Technician in your area by
visiting safercar.gov and select “Find Local Child Seat Help” or call
1-866-SEAT CHECK (1-866-732-8243).
13
Page 9
BOOSTER SEAT COMPONENTS BOOSTER SEAT COMPONENTS
Headrest
Shoulder
Belt Guide
Shoulder Positioning
Clip & Webbing
(Backless Mode)
Backrest
Connection
Release
Height
Adjust Lever
Backrest
Lap Belt Guide
BOOSTER SEAT OVERVIEW
14
Armrest
Cup Holder
LATCH
Adjustment
Strap
LATCH
Connector
User Guide
Storage
LATCH
Connector
Shoulder Belt
Clip Storage
BOOSTER SEAT OVERVIEW
15
Page 10
HIGH-BACK MODE
HIGH-BACK MODE
WARNING! High-Back Mode use of this Booster Seat is ONLY for
children who meet ALL of the requirements shown here. If the child is not
within these requirements because they are too small, select a different
child seat (such as a forward facing harness seat or convertible seat).
To ensure a correct installation of the Booster Seat, you must follow the step
by step instructions in this user guide.
BOOSTER SEAT OVERVIEW
16
High-Back Mode:
30 – 100 lbs (13.6 – 45.3 kg)
Use High-Back Mode with children:
• Who are at least four years old.
30 lbs 100 lbs
(13.6 kg) (45.3 kg)
• Who weigh between 30 and 100 lbs
(13.6 – 45.3 kg).
• Who are 38”to 57” (97 -145 cm) tall and the
child’s ears are below the headrest.
• Who demonstrate an ability to sit relatively
still and properly in a seat belt at all times.
See Adjusting Shoulder Belt
Guide Height on page 38.
HIGH-BACK
BOOSTER SEAT OVERVIEW
17
Page 11
BACKLESS MODE BACKLESS MODE
WARNING! Backless Mode use of this Booster Seat is ONLY for children
who meet ALL of the requirements shown here. If the child is not within
these requirements because the child is too small, review the HIGH-BACK
BOOSTER MODE guidelines on page 16 or select a different child seat.
To ensure a correct installation of the Booster Seat, you must follow the step
by step instructions in this user guide.
BOOSTER SEAT OVERVIEW
18
Backless Mode:
40 – 110 lbs (18 – 50 kg)
Use Backless Mode with children:
• Who are at least four years old.
• Who weigh between 40 and 110 lbs
(18 – 50 kg).
• Who are 38”- 57”(97 -145 cm) tall and the child’s
ears are below vehicle seat.
• Who demonstrate an ability to sit relatively
still and properly in a seat belt at all times.
See Adjusting Shoulder Belt
Clip Height on page 58.
BACKLESS
40 lbs 110 lbs
(18 kg) (50 kg)
BOOSTER SEAT OVERVIEW
19
Page 12
VEHICLE SEATING POSITIONS VEHICLE SEATING POSITIONS
VEHICLE INFORMATION
The back seat is the safest place for children 12 and under. See your vehicle
20
owner’s manual for Booster Seat installation and instructions.
WARNING! WHEN USING THIS CHILD RESTRAINT, DO NOT PLACE
THIS CHILD RESTRAINT IN A VEHICLE SEATING LOCATION WITH A
FRONTAL AIR BAG, UNLESS THE AIR BAG CAN BE TURNED OFF.
Some vehicles have no seating positions which are compatible with this Booster
Seat. Only forward-facing vehicle seats can be used with this Booster Seat.
Never use side or rear facing seats. If in doubt, contact the vehicle manufacturer
for assistance.
This Booster Seat must be
installed in a vehicle seat with
a 3-point seat belt (shoulder
belt and lap belt). NEVER use
lap belt only.
VEHICLE INFORMATION
21
Page 13
VEHICLE SEAT BELTS VEHICLE SEAT BELTS
Vehicle seat belts differ from vehicle to vehicle. Refer to your vehicle owner’s
manual for specific information about seat belts and their use with booster
seats.
Shoulder belt with switchable retractor:
Refer to your vehicle owners manual for information regarding switchable
retractors and booster seat use.
Inflatable seat belts:
Follow the vehicle manufacturer’s instructions for use with this Booster Seat.
VEHICLE INFORMATION
22
The following types of vehicle belts MUST NOT be used to install this
Booster Seat.
If any of the belt types listed below are in the chosen seating position, you
must choose another vehicle seating position.
1 2
1. Never use a Lap belt with motorized
Shoulder belt.
2. Never use vehicle belts that are
attached to the door or that move along
a track.
3. Never use a Lap-only belt.
3
VEHICLE INFORMATION
23
Page 14
WHAT IS LATCH? WHAT IS LATCH?
Vehicle
Lower Anchor
Points
Vehicle
Seat Crease
WARNING: This Booster Seat is designed to be used with
lower LATCH anchors at the standard spacing (11 inches (28 cm))
ONLY! Refer to vehicle owner’s manual for information about
LATCH and Booster Seat installation positions.
LATCH = Lower Anchors and Tethers for CHildren
On this Booster Seat, Lower Anchors are only used to restrain the Booster Seat,
not to restrain your child. To secure your child, a vehicle Lap-Shoulder Belt
MUST be used.
Please refer to the vehicle owner’s manual for designated Lower Anchor locations
in vehicles.
anchors may also be used to secure the Booster Seat.
VEHICLE INFORMATION
If the vehicle is equipped with LATCH, the vehicle lower anchor points may be visible at the
seat crease. If not visible, the seating position may be marked with a symbol as shown or a
colored dot. The top tether anchor is not used with this Booster Seat.
Some vehicles owner’s manual use the term “ISOFIX”. ISOFIX lower
VEHICLE INFORMATION
24
25
Page 15
ASSEMBLYASSEMBLY
R
Assemble the Cup Holder
Match up the letter (L or R) on the bottom of the Cup Holder with the
1
matching letter on the Booster Seat and insert the Cup Holder into the
correct side.
Lip
ASSEMBLY INFORMATION
26
Make sure the Cup Holder lip fits behind the groove on the Booster Seat
bottom, as shown.
1
R
R
R
ASSEMBLY INFORMATION
27
Page 16
Assemble the Armrests
Attach both Armrests to the Booster Seat Bottom, as shown. Press
2
firmly on Armrests until they click into place. Pull up on both
Armrests to make sure they are securely attached.
Never use Booster Seat without Armrests attached.
ASSEMBLYASSEMBLY
2
“CLICK”
ASSEMBLY INFORMATION
28
ASSEMBLY INFORMATION
29
Page 17
ASSEMBLYASSEMBLY
3
4a
4b
ASSEMBLY INFORMATION
30
Assemble the Backrest
Attach the Backrest to the Booster Seat Bottom, by hooking the Backrest
over the seat bar hinge on the seat bottom, as shown.
Slide the edge of the Fabric Panel between the Fabric Cover and the Seat
Back Frame. Be sure Fabric Panel is laying flat against the Seat Back
frame to provide padding for your child.
Rotate the Backrest up until it clicks into an upright position.
4a
3
4b
ASSEMBLY INFORMATION
“CLICK”
31
Page 18
ADJUSTING BACKREST HEIGHT ADJUSTING BACKREST HEIGHT
1
While holding the Booster Seat firmly with one hand on the seat, use
the other hand to squeeze the Height Adjuster Lever located at the
back of the Headrest.
Raise/Lower the Backrest to correctly fit the Booster Seat to your
2
child.
When correct position is reached, release the Height Adjust Lever and
slightly raise or lower the Backrest until you hear a click, indicating
HIGH-BACK MODE
that the Backrest is locked into position.
The Booster Seat Backrest has 10 height positions to allow the Booster Seat to
grow with your child. Ensure that the child’s head is positioned correctly within the
Headrest and that the Shoulder Belt is placed correctly over the child’s shoulder.
1
2
2
“CLICK”
“CLICK”
HIGH-BACK MODE
32
33
Page 19
INSTALL HIGH-BACK BOOSTER SEAT INSTALL HIGH-BACK BOOSTER SEAT
1
Place the Booster Seat on the vehicle seat, push the Booster Seat
Backrest against the back of the vehicle seat.
2
Check that the head restraint of the vehicle seat does not interfere with
the Headrest of the Booster Seat. If the vehicle head restraint pushes
the Booster Seat Headrest forward, raise or remove the vehicle head
restraint, if possible. If it is not possible to move the vehicle head
restraint out of the way, use the Booster Seat in the Backless Mode.
Ensure the child is the proper size to use the Backless Booster Seat.
Refer to page 18.
1
2
HIGH-BACK MODE
34
HIGH-BACK MODE
Always replace the vehicle head restraint when the Booster Seat is removed.
35
Page 20
INSTALL HIGH-BACK BOOSTER SEAT INSTALL HIGH-BACK BOOSTER SEAT
HIGH-BACK MODE
36
Use of LATCH Connectors with this Booster Seat is optional. If the LATCH Connectors
are not used, pull the LATCH Tightening Strap snug so that the LATCH Connectors do
not interfere with the seat belt.
3
If using the LATCH Connectors, release the LATCH Adjustment Strap,
press in the button located on the front of the seat bottom and pull out
both LATCH Connectors.
Locate the LATCH lower anchor bars in your vehicle. Attach both LATCH
4
Connectors to the vehicle lower anchor bars.
Pull on the LATCH Adjustment Strap and push back on the seat
5
bottom to snug up the Booster Seat to the vehicle seat back.
4
“CLICK”
3
“CLICK”
5
HIGH-BACK MODE
37
Page 21
SECURING CHILD IN BOOSTER SEAT SECURING CHILD IN BOOSTER SEAT
Place the child into the Booster Seat, making sure the child is sitting with
1
his/her back against the Booster Seat Backrest.
The Shoulder Belt Guide must be positioned at or just slightly above the
2
child’s shoulders. Adjust the seat back to the proper height. Make sure
the shoulder belt lays across the shoulder and over the center of the
child’s chest. The lap belt should lay over the child’s thighs.
1
HIGH-BACK MODE
38
If Shoulder Belt Guide is NOT positioned at or just slightly above the child’s
shoulders see page 32 for Adjusting Backrest Height.
Child’s ears must be below Headrest when sitting on Booster Seat. If the child’s
ears are above the Headrest, use the Backless Booster Mode refer to page 46.
2
HIGH-BACK MODE
39
Page 22
SECURING CHILD IN BOOSTER SEAT SECURING CHILD IN BOOSTER SEAT
Route the lap belt UNDER the 1st Armrest, across the child’s thighs,
3a
then route the shoulder belt and the lap belt UNDER the 2nd Armrest
closest to the vehicle buckle as shown. Lap-Shoulder belts MUST be
under the ARMRESTS, as shown.
3a
Buckle the seat belt.
3b
HIGH-BACK MODE
40
3b
HIGH-BACK MODE
41
Page 23
SECURING CHILD IN BOOSTER SEAT SECURING CHILD IN BOOSTER SEAT
Slide the shoulder belt through the orange Shoulder Belt Guide (A).
4
Make sure belt is below belt guide clip (B).
The lap belt should lay flat and snug across the child’s thighs. And,
when the shoulder belt is pulled up, it will lay flat and snug across the
child’s chest.
The seat belt can remain in the Shoulder Belt Clip until the seat is
removed from the Vehicle.
4
4a
4b
HIGH-BACK MODE
HIGH-BACK MODE
42
43
Page 24
SECURING CHILD IN BOOSTER SEAT SECURING CHILD IN BOOSTER SEAT
Ensure the child is secured correctly as shown.
5
5
HIGH-BACK MODE
44
HIGH-BACK MODE
45
Page 25
REMOVING BACKREST
To remove the Backrest, turn the seat over and press down on the
1
Backrest Connection Release at the base of the seat back under the
seat bar.
At the same time rotate the seat back (A) and remove Backrest from
2
the Booster Seat bottom (B), as shown.
REMOVING BACKREST
2a
1
BACKLESS MODE
46
2b
BACKLESS MODE
47
Page 26
REMOVING BACKREST
Tuck the Fabric Panel between the fabric cover and the seat surface, as
3
shown.
REMOVING BACKREST
3
BACKLESS MODE
48
BACKLESS MODE
49
Page 27
USING SHOULDER BELT CLIP
The Shoulder Belt Clip is stored under the Booster Seat bottom.
1
Remove the Shoulder Belt Clip and Strap stored underneath seat.
Place the Booster Seat onto the vehicle seat.
2
1
USING SHOULDER BELT CLIP
2
BACKLESS MODE
50
BACKLESS MODE
51
Page 28
INSTALLING BACKLESS BOOSTER SEAT
If using LATCH Connectors, release LATCH Adjustment Strap, press in the
3
button located on the front of the seat bottom (A) and pull out on both
LATCH Connectors (B).
Use of
LATCH Connectors
Connectors
Connectors do not interfere with the seat belt. Skip to “Securing Child in Booster
Seat” section page 56.
are not used, pull the LATCH Adjustment Strap snug so that the
with this Booster Seat is optional. If the
LATCH
LATCH
INSTALLING BACKLESS BOOSTER SEAT
3a
3b
BACKLESS MODE
52
BACKLESS MODE
53
Page 29
INSTALLING BACKLESS BOOSTER SEAT
Locate the LATCH lower anchor bars in your vehicle. Attach both
4
LATCH Connectors to the vehicle lower anchor bars.
INSTALLING BACKLESS BOOSTER SEAT
5
BACKLESS MODE
54
Pull on the LATCH Adjustment Strap and push back on the seat bottom
to snug up the Booster Seat to the vehicle seat back.
4 5
“CLICK”
BACKLESS MODE
“CLICK”
55
Page 30
SECURING CHILD IN BOOSTER SEAT
Place the child into the Booster Seat, making sure the child is sitting
1
with his/her back against the vehicle seat back.
SECURING CHILD IN BOOSTER SEAT
Child’s ears must be below vehicle seat back or vehicle head restraint when sitting
on Booster Seat. If the child’s ears are above the vehicle seat back or vehicle head
restraint when it is fully extended, use the High-Back Mode. Refer to page 32.
2a
BACKLESS MODE
2b
56
Route the lap belt UNDER the 1st Armrest, across the child’s thighs,
Then route the shoulder belt and the lap belt UNDER the 2nd Armrest
closest to the vehicle buckle as shown. Lap-Shoulder belts MUST be
under ARMRESTS, as shown.
Buckle the seat belt.
2a
1
2b
BACKLESS MODE
57
Page 31
SECURING CHILD IN BOOSTER SEAT
3
To adjust the Shoulder Positioning Clip, pull the clip up or down to
adjust the Shoulder Positioning Clip to be at or slightly above the child’s
shoulders.
4
Slide the vehicle shoulder belt through the Shoulder Positioning Clip
(as shown). Shoulder Positioning Clip must be at child’s shoulder.
If necessary, readjust the location of the Clip to ensure that the seat belt
lays flat and snug across the child’s chest and the lap belt lays flat and
snug across the child’s thighs.
BACKLESS MODE
3
SECURING CHILD IN BOOSTER SEAT
4
BACKLESS MODE
58
59
Page 32
SECURING CHILD IN BOOSTER SEAT
Child is now secured correctly, as shown.
5
When using in Backless Mode, the Shoulder Positioning Clip must be used until the
seat belt naturally lays flat across the center of the child’s shoulder.
SECURING CHILD IN BOOSTER SEAT
5
BACKLESS MODE
60
BACKLESS MODE
61
Page 33
SECURING CHILD CHECKLIST SECURING CHILD CHECKLIST
SAFETY INFORMATION
62
ALWAYS check to make sure vehicle seat belt is
securely buckled. If buckle separates, child could be killed
or seriously injured.
Check that the seat belt is not twisted.
Check that the shoulder belt is snug on the child’s shoulder and
that it does not rub on the neck. It should lie flat across the
child’s chest and middle of shoulder. The Shoulder Belt Guide
should be at or just above the child’s shoulder. If necessary,
raise or lower the Booster Seat Backrest.
DO NOT use anything (pillows, blankets, etc.)
between the Booster Seat and the vehicle seat or
between the child and the Booster Seat. Avoid
bulky clothing that interferes with proper seat belt
placement. In the event of an accident, the Booster
Seat may not operate correctly.
Do not let your child slide forward
or downward while in the Booster
Seat.
Never use the vehicle belt in any
position other than those indicated
in this User Guide!
SAFETY INFORMATION
63
Page 34
BOOSTER SEAT SAFE USE CHECKLIST BOOSTER SEAT SAFE USE CHECKLIST
To avoid injury to others, ALWAYS secure this Booster Seat when
unoccupied. An unsecured Booster Seat could injure other occupants in
a sudden stop or crash.
Secure the unoccupied Booster Seat with either LATCH or the vehicle belt
by following the appropriate steps below. The LATCH system is adequate
to secure the Backless Booster Seat, but the Lap-Shoulder belt should be
used to secure the High-Back Booster Seat.
Follow steps 3-5 to use LATCH page 52.
1
High-Back Mode, follow steps 3-4 to use Lap-Shoulder belt page 40.
2
SAFETY INFORMATION
Backless Mode, follow step 2 to use Lap-Shoulder belt page 56.
1
2
SAFETY INFORMATION
64
65
Page 35
INSTALLATION ON AN AIRCRAFT
• This Booster Seat is NOT certified for aircraft use. Aircraft do not have
lap-shoulder belts to secure your child.
INSTALLATION ON AN AIRCRAFT
ADDITIONAL INFORMATION
66
ADDITIONAL INFORMATION
67
Page 36
CUP HOLDER CUP HOLDER
WARNING! DO NOT place hot liquids in cup holder. If spilled, hot
liquids could burn child. PLASTIC CONTAINERS ONLY - No glass or metal
containers. Only use cups with less than 12 oz. (355 ml) capacity. Never
place sharp or pointed objects in Cup Holder. In a crash these objects could
hit you or your child and cause serious injuries.
To remove the Cup Holders press in on the release button on the bottom
1
of the Booster Seat.
The Cup Holders can also be folded in to allow others to sit next to the
2
Booster Seat.
1
2
ADDITIONAL INFORMATION
68
ADDITIONAL INFORMATION
69
Page 37
RELEASE LATCH CONNECTORS RELEASE LATCH CONNECTORS
To release the LATCH Connectors and remove the Booster Seat, press
1
in the button located on the front of the seat bottom while pulling the
Booster Seat out to loosen the LATCH Connectors.
Then pull out on the loops on the LATCH Straps, as shown. Pull the
2
LATCH Adjustment Strap tight to store the LATCH Connectors.
1
2
ADDITIONAL INFORMATION
70
ADDITIONAL INFORMATION
71
Page 38
REMOVING FABRIC COVERS REMOVING FABRIC COVERS
Booster Seat bottom
Remove both Cup Holders and flip the Booster Seat bottom over and
1
unhook 6 elastic loops, as shown.
If Backrest is attached to the seat bottom, see page 46 for removing Backrest.
Both Cup Holders need to be removed before fabric can be removed, refer to
page 68.
ADDITIONAL INFORMATION
72
1
ADDITIONAL INFORMATION
73
Page 39
REMOVING FABRIC COVERS
Flip the fabric over and remove the Foam Pad before washing the fabric.
2
Make sure to insert the Foam Pad into the fabric seat bottom before
reinstalling onto the seat bottom frame.
REMOVING FABRIC COVERS
2
ADDITIONAL INFORMATION
74
ADDITIONAL INFORMATION
75
Page 40
REMOVING FABRIC COVERS REMOVING FABRIC COVERS
Backrest fabric cover
On the Booster Seat Backrest, unhook 6 elastic loops as shown. Four
1
behind the Headrest and two at the bottom of the seat back.
ADDITIONAL INFORMATION
76
1
ADDITIONAL INFORMATION
77
Page 41
REMOVING FABRIC COVERS REMOVING FABRIC COVERS
Backrest fabric cover
Lift up on the plastic tabs at the top of the Headrest and below the
2
Shoulder Belt Guides, as shown. Pull the Backrest fabric cover forward
to remove.
ADDITIONAL INFORMATION
78
2
ADDITIONAL INFORMATION
79
Page 42
REMOVING FABRIC COVERS REMOVING FABRIC COVERS
Repeat Removing Fabric steps in the reverse order, ensuring that the fabric
cover fits onto and around the frame correctly, in particular around the orange
belt guides.
Position the fabric cover on the Booster Seat Backrest and reattach all
1
elastic loops.
Tuck in the fabric along the Backrest edges.
2
ADDITIONAL INFORMATION
80
1
2
ADDITIONAL INFORMATION
81
Page 43
REMOVING FABRIC COVERS REMOVING FABRIC COVERS
3
Insert the plastic tab on the top of the Headrest into the long groove right
above the top edge of the Backrest.
Insert the plastic tab below the Shoulder Belt Guide, slide between the
4
Backrest and foam. Repeat for the other side.
3
4
ADDITIONAL INFORMATION
82
ADDITIONAL INFORMATION
83
Page 44
REMOVING FABRIC COVERS REMOVING FABRIC COVERS
The foam pad MUST be inserted into the seat bottom fabric, see page 74.
5
Position the fabric cover on the Booster Seat bottom and tuck in the fabric
along the belt guide edges. Flip the seat bottom over. Then tighten the
fabric over the Booster Seat bottom further by reattaching the elastic
loops, as shown.
Be sure to fit fabric cover carefully around all orange belt guides.
The Booster Seat must NEVER be used without the fabric cover. It may
not perform as intended in the event of a crash.
ADDITIONAL INFORMATION
84
5
ADDITIONAL INFORMATION
85
Page 45
REMOVING ARMREST COVERS REMOVING ARMREST COVERS
Armrest covers
Locate the Armrest release button directly under the front of the Armrest.
1
Pull on the button and at the same time lift up on the front edge to remove
the Armrest pad.
1
ADDITIONAL INFORMATION
86
ADDITIONAL INFORMATION
87
Page 46
REMOVING ARMREST COVERS REMOVING ARMREST COVERS
Pull back on the edges of the Armrest fabric covers and slide the fabric off
2
the Armrest base.
3
To reattach the Armrest, insert the Back Tab into the Armrest base and
3
push down on the front edge until it clicks into the base.
2
NEVER use seat without Armrest fabric covers.
Back
Tab
ADDITIONAL INFORMATION
88
Back
Tab
ADDITIONAL INFORMATION
89
Page 47
CLEANING AND MAINTENANCE
DO NOT USE BLEACH, solvents or household cleaners as they may
weaken plastics and straps.
DO NOT USE SOAPS OR LUBRICANTS on the LATCH Connectors or
straps. It may cause them to malfunction.
• Fabrics may be spot-cleaned:
Hand wash using mild soap and water, or machine wash in cold water
on delicate cycle using mild detergent. Hang to dry. See page 72 for
removal instructions.
• Foam Insert:
Hand rinse and air dry.
ADDITIONAL INFORMATION
• Cleaning Plastics:
Sponge clean using warm water and mild soap. Towel dry.
CLEANING AND MAINTENANCE
• Cleaning LATCH Connectors Hardware and Straps:
LATCH Connectors hardware and straps cannot be replaced. Sponge
clean using warm water. Air dry.
• Storing the Booster:
When it is not installed in the car, it is recommended to store the
Booster in a dry place, away from sources of heat, dust, humidity and
direct sunlight.
ADDITIONAL INFORMATION
90
91
Page 48
Loading...