Chicago Electric MIG 200 User Manual
WELDER DUAL
®
MIG 200
Model 93804
ASSEMBLY AND OPERATING INSTRUCTIONS
Due to continuing improvements, actual product may differ slightly from the product described herein.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at: http://www.harborfreight.com
TO PREVENT SERIOUS INJURY,
READ AND UNDERSTAND ALL WARNINGS
AND INSTRUCTIONS BEFORE USE.
Copyright 2006 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
©
without the express written consent of Harbor Freight Tools.
For technical questions, please call 1-800-444-3353.
Contents
PRODUCT SPECIFICATIONS................................................... 3
GENERAL SAFETY RULES ..................................................... 3
Specific Safety Rules ........................................................................6
Grounding...........................................................................................9
Extension Cords ...............................................................................10
Symbology ........................................................................................ 10
UNPACKING............................................................................. 10
ASSEMBLY INSTRUCTIONS ................................................... 11
To Attach The Wheels .......................................................................11
To Install The Wire Spool ..................................................................11
To Route The Wire .............................................................................12
To Change Wire Settings .................................................................15
Setting The Gun Polarity For Wire Type .........................................16
To Attach The Ground Cable With Clamp ...................................... 16
To Install A Gas Cylinder .................................................................17
OPERATING INSTRUCTIONS ................................................. 18
Before You Begin Welding ...............................................................18
Duty Cycle (Duration of Use)...........................................................18
Setting Up The Weld..........................................................................19
Holding The Welding Torch ..............................................................20
Weld Settings Chart .......................................................................... 21
Volt-Ampere Curves ......................................................................... 22
Weld Diagnosis .................................................................................23
When the Weld is Completed .......................................................... 25
INSPECTION, MAINTENANCE, AND CLEANING ................... 26
Nozzle Inspection, Cleaning, and Replacement ...........................26
Contact Tip Inspection, Cleaning, And Replacement .................. 26
Replacing The Welding Torch Liner ................................................ 27
PARTS LISTS & ASSEMBLY DIAGRAMS ............................... 28
Electrical Schematic.........................................................................33
TROUBLESHOOTING .............................................................. 34
WARRANTY ............................................................................. 36
For technical questions, please call 1-800-444-3353;
Troubleshooting section at end of manual.
Page 2SKU 93804
PRODUCT SPECIFICATIONS
tnerruCgnidleWspmA002~03
yticapaCgnidleW ssenkciht"63.0ot"20.0gnidlewroF
elcyCytuD
noitpmusnoCrewoP spmA83/esahPelgniS/zH06/tloV032
egatloVnepO43-61
gulPrewoPderiuqeR
epyT
gnitaRdroCrewoPC
eziStelnIsaG"4/1
etaRwolFsaG )ruoHrepteeFcibuC(HFC57.13~5.01
elbaCdnuorG pmalcgnidnuorghtiwgnoL"7'6
lbaCrewoPhcroTgnoL"7'8
e
)thgiLhtiw(noitcetorPdaolrevOlamrehT nwodloocretfatratserdnanwodtuhscitamotuA
eriW )mm2.1otmm8.0("540.0ot"30.0
eziS
piThcroT8.0
snoisnemiDllarevOH"12xW"01xL"2/1-62
thgieWteNsdnuoP6.48
SAVE THIS MANUAL
1
1sdleW(
/
2
tnelaviuqero05-6L#AMEN
3xGWA8
spmA002@%51/spmA08@%001
)egarepmalluf@setunim01fotuosetunim
)dedulcniton(kcoltsiwt,deziralop,CAV022,gnorP-3
You will need this manual for the safety warnings and precautions, assembly, operating,
inspection, maintenance and cleaning procedures, parts list and assembly diagram.
Keep your invoice with this manual. Write the invoice number on the inside of the front
cover. Keep this manual and invoice in a safe and dry place for future reference.
GENERAL SAFETY RULES
WARNING!
READ AND UNDERSTAND ALL INSTRUCTIONS
Failure to follow all instructions listed below may result in
electric shock, fire, and/or serious injury.
SAVE THESE INSTRUCTIONS
WORK AREA
1. Keep your work area clean and well lit. Cluttered benches and dark areas invite
accidents.
2. Do not operate power tools in explosive atmospheres, such as in the presence
of flammable liquids, gases, or dust. Power tools create sparks which may ignite
the dust or fumes.
3. Keep bystanders, children, and visitors away while operating a power tool.
Distractions can cause you to lose control. Protect others in the work area from
debris such as chips and sparks. Provide barriers or shields as needed.
For technical questions, please call 1-800-444-3353;
Troubleshooting section at end of manual.
Page 3SKU 93804
ELECTRICAL SAFETY
4. Grounded tools must be plugged into an outlet properly installed and grounded
in accordance with all codes and ordinances. Never remove the grounding
prong or modify the plug in any way. Do not use any adapter plugs. Check
with a qualified electrician if you are in doubt as to whether the outlet is properly
grounded. If the tools should electrically malfunction or break down, grounding
provides a low resistance path to carry electricity away from the user.
5. Avoid body contact with grounded surfaces such as pipes, radiators, ranges,
and refrigerators. There is an increased risk of electric shock if your body is
grounded.
6. Do not expose power tools to rain or wet conditions. Water entering a power
tool will increase the risk of electric shock.
7. Do not abuse the Power Cord. Never use the Power Cord to carry the tools or
pull the Plug from an outlet. Keep the Power Cord away from heat, oil, sharp
edges, or moving parts. Replace damaged Power Cords immediately. Damaged
Power Cords increase the risk of electric shock.
8. When operating a power tool outside, use an outdoor extension cord marked
“W-A” or “W”. These extension cords are rated for outdoor use, and reduce the risk
of electric shock.
PERSONAL SAFETY
9. Stay alert. Watch what you are doing, and use common sense when operating
a power tool. Do not use a power tool while tired or under the influence of
drugs, alcohol, or medication. A moment of inattention while operating power
tools may result in serious personal injury.
10. Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep
your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry,
or long hair can be caught in moving parts.
11. Avoid accidental starting. Be sure the Power Switch is off before plugging in.
Carrying power tools with your finger on the Power Switch, or plugging in power
tools with the Power Switch on, invites accidents.
12. Remove adjusting keys or wrenches before turning the power tool on. A wrench
or a key that is left attached to a rotating part of the power tool may result in personal
injury.
13. Do not overreach. Keep proper footing and balance at all times. Proper footing
and balance enables better control of the power tool in unexpected situations.
14. Always wear eye, hearing, and breathing protection. For welding safety
equipment, refer to number 9 on page 6.
TOOL USE AND CARE
For technical questions, please call 1-800-444-3353;
Troubleshooting section at end of manual.
Page 4SKU 93804
15. Use clamps (not included) or other practical ways to secure and support the
workpiece to a stable platform. Holding the work by hand or against your body is
unstable and may lead to loss of control.
16. Do not force the tool. Use the correct tool for your application. The correct tool
will do the job better and safer at the rate for which it is designed.
17. Do not use the power tool if the Power Switch does not turn it on or off. Any
tool that cannot be controlled with the Power Switch is dangerous and must be
replaced.
18. Disconnect the Power Cord Plug from the power source before making any
adjustments, changing accessories, or storing the tool. Such preventive safety
measures reduce the risk of starting the tool accidentally.
19. Store idle tools out of reach of children and other untrained persons. Tools are
dangerous in the hands of untrained users.
20. Maintain tools with care. Keep cutting tools sharp and clean. Properly
maintained tools with a sharp cutting edge are less likely to bind and are easier to
control. Do not use a damaged tool. Tag damaged tools “Do not use” until repaired.
21. Check for misalignment or binding of moving parts, breakage of parts, and
any other condition that may affect the tool’s operation. If damaged, have the
tool serviced before using. Many accidents are caused by poorly maintained
tools.
22. Use only accessories that are recommended by the manufacturer for your
model. Accessories that may be suitable for one tool may become hazardous when
used on another tool.
SERVICE
23. Tool service must be performed only by qualified repair personnel. Service or
maintenance performed by unqualified personnel could result in a risk of injury.
24. When servicing a tool, use only identical replacement parts. Follow instructions
in the
unauthorized parts or failure to follow maintenance instructions may create a risk of
electric shock or injury.
“Inspection, Maintenance, And Cleaning”
section of this manual. Use of
For technical questions, please call 1-800-444-3353;
Troubleshooting section at end of manual.
Page 5SKU 93804
SPECIFIC SAFETY RULES
1. Ground this product. This Welder requires the attachment and use of a UL®listed, 220 volt, grounded, 3-prong, electrical Power Cord Plug (not included). Only
a qualified electrician should install the Power Cord Plug. Never remove the
grounding prong or modify the Power Cord Plug in any way. Do not use adapter
plugs with this product. To comply with the National Electric Code, and to provide
additional protection from the risk of electrical shock, this product should only be
connected to a 220 volt, 3-hole outlet that is properly grounded.
2. Maintain labels and nameplates on the Welder. These carry important information.
If unreadable or missing, contact Harbor Freight Tools for a replacement.
3. Avoid unintentional starting. Make sure you are prepared to begin work before
turning on the Welder.
4. Do not force the Welder. This tool will do the work better and safer at the speed
and capacity for which it was designed.
5. Never leave the Welder unattended when it is plugged into an electrical outlet.
Turn off the tool, and unplug it from its electrical outlet before leaving.
6. Industrial applications must follow OSHA guidelines.
7. Never stand on the Welder. Serious injury could result if the Welder is tipped or if
hot surfaces are accidently contacted.
8. Maintain a safe working environment. Keep the work area well lit. Make sure
there is adequate surrounding workspace. Always keep the work area free of
obstructions, grease, oil, trash, and other debris. Do not use a power tool in areas
near flammable chemicals, dusts, and vapors. Do not use this product in a damp or
wet location.
9.
• Leather leggings, fire resistant shoes or boots should be worn when using this
• Keep clothing free of grease, oil, solvents, or any flammable substances. Wear
• Wear an approved head covering to protect the head and neck. Use aprons,
• When welding/cutting overhead or in confined spaces, wear flame resistant ear
Prevent eye injury and burns. Wearing and using ANSI-approved personal
safety clothing and safety devices reduce the risk for injury.
• Wear ANSI-approved safety impact eye goggles with a welding helmet
with protective lens.
product. Do not wear pants with cuffs, shirts with open pockets, or any clothing
that can catch and hold molten metal or sparks.
dry, insulating gloves and protective clothing.
cape, sleeves, shoulder covers, and bibs designed and approved for welding
and cutting procedures.
plugs or ear muffs to keep sparks out of ears.
For technical questions, please call 1-800-444-3353;
Troubleshooting section at end of manual.
Page 6SKU 93804
10.
Prevent accidental fires. Remove any combustible material from the work
area.
• When possible, move the work to a location well away from combustible
materials. If relocation is not possible, protect the combustibles with a
cover made of fire resistant material.
• Remove or make safe all combustible materials for a radius of 35 feet (10 meters)
around the work area. Use a fire resistant material to cover or block all open
doorways, windows, cracks, and other openings.
• Enclose the work area with portable fire resistant screens. Protect combustible
walls, ceilings, floors, etc., from sparks and heat with fire resistant covers.
• If working on a metal wall, ceiling, etc., prevent ignition of combustibles on the
other side by moving the combustibles to a safe location. If relocation of
combustibles is not possible, designate someone to serve as a fire watch,
equipped with a fire extinguisher, during the cutting process and for at least one
half hour after the cutting is completed.
• Do not weld or cut on materials having a combustible coating or combustible
internal structure, as in walls or ceilings, without an approved method for
eliminating the hazard.
• Do not dispose of hot slag in containers holding combustible materials. Keep a
fire extinguisher nearby and know how to use it.
• After spot welding, make a thorough examination for evidence of fire. Be aware
that easily-visible smoke or flame may not be present for some time after the fire
has started. Do not weld or cut in atmospheres containing dangerously reactive
or flammable gases, vapors, liquids, and dust. Provide adequate ventilation in
work areas to prevent accumulation of flammable gases, vapors, and dust. Do
not apply heat to a container that has held an unknown substance or a
combustible material whose contents, when heated, can produce flammable or
explosive vapors. Clean and purge containers before applying heat. Vent closed
containers, including castings, before preheating, welding, or cutting.
11. Avoid overexposure to fumes and gases. Always keep your head out of the
fumes. Do not breathe the fumes. Use enough ventilation or exhaust, or both, to
keep fumes and gases from your breathing zone and general area.
• Where ventilation is questionable, have a qualified technician take an air
sampling to determine the need for corrective measures. Use mechanical
ventilation to improve air quality. If engineering controls are not feasible, use an
approved respirator.
• Work in a confined area only if it is well ventilated, or while wearing an air-
supplied respirator.
• Follow OSHA guidelines for Permissible Exposure Limits (PEL’s) for various
fumes and gases.
• Follow the American Conference of Governmental Industrial Hygienists
recommendations for Threshold Limit Values (TLV’s) for fumes and gases.
For technical questions, please call 1-800-444-3353;
Troubleshooting section at end of manual.
Page 7SKU 93804
• Have a recognized specialist in Industrial Hygiene or Environmental Services
check the operation and air quality and make recommendations for the specific
welding or cutting situation.
Inhalation Hazard
Welding Produces TOXIC FUMES and GASSES.
Exposure to welding gasses can increase the risk of developing
certain cancers, such as cancer of the larynx and lung cancer.
Also, some diseases that may be linked to exposure to welding gasses
or fumes are:
•
Early onset of Parkinson’s Disease • Heart Disease
• Damage to the reproductive organs • Ulcers
• Inflammation of the small intestine or stomach • Kidney damage
• Respiratory diseases such as emphysema, bronchitis or pneumonia
Safety precautions, such as using natural or forced air ventilation
and wearing a NIOSH-approved respirator, are ESSENTIAL to reduce
the risk of developing the above illnesses.
12. Read and understand all instructions and safety precautions as outlined in
the manufacturer’s manual for the material you will weld or cut.
13. Do not touch live electrical parts. Wear dry, insulating gloves. Do not touch
electrode or conductor tong with bare hand. Do not wear wet or damaged gloves.
14. Protect yourself from electric shock. Do not use outdoors. Insulate yourself from
the workpiece and ground. Use nonflammable, dry insulating material if possible, or
use dry rubber mats, dry wood or plywood, or other dry insulating material big enough
to cover your full area of contact with the work or ground.
15. Ensure that the unit is placed on a stable location before use. If this unit falls
while plugged in, severe injury, electric shock, or fire may result.
16.
• Keep cylinders away from any electrical circuits, including welding circuits.
• Keep protective cap in place over the valve except when the cylinder is in use.
• Use only correct gas shielding equipment designed specifically for the type of
• Always protect gas cylinders from heat, being struck, physical damage, slag,
• Always use proper procedures to move cylinders.
Cylinders can explode when damaged:
• Never weld on a pressurized or a closed cylinder.
• Never lay a welding torch on a cylinder.
• Never allow a welding electrode to touch the cylinder.
welding you will do. Maintain this equipment properly.
flames, sparks, and arcs.
For technical questions, please call 1-800-444-3353;
Troubleshooting section at end of manual.
Page 8SKU 93804
17. Use the right tool for the job. Do not attempt to force small equipment to do the
work of larger industrial equipment. There are certain applications for which this
Welder was designed. It will do the job better and more safely at the rate for which
it was intended. Do not modify this Welder, and do not use this Welder for a purpose
for which it was not intended.
18.
19.
20.
WARNING! People with pacemakers should consult their physician(s) before
using this product. Electromagnetic fields in close proximity to a heart pacemaker
could cause interference to or failure of the pacemaker.
WARNING! The warnings and cautions discussed in this manual cannot cover
all possible conditions and situations that may occur. It must be understood by the
operator that common sense and caution are factors which cannot be built into this
product, but must be supplied by the operator.
WARNING! This product, when used for welding and similar applications,
produces chemicals known to the State of California to cause cancer and birth
defects (or other reproductive harm).
(California Health & Safety Code § 25249.5,
SAVE THESE INSTRUCTIONS
et seq.
)
GROUNDING
NOTE:
This Welder requires the installation of a 3-Prong, 220 VAC, polarized,
twistlock Power Cord Plug (not included).
NEMA configuration # L6-50 or equivalent
The Plug must be installed by a certified electrician.
WARNING!
Improperly connecting the grounding wire can result in the risk of electric shock. Check with a qualified electrician if you are in doubt as to
whether the outlet is properly grounded. Do not modify the power cord
plug used with the tool. Never remove the grounding prong from the
plug. Do not use the tool if the power cord or plug is damaged. If damaged, have it repaired by a service facility before use. If the plug will not
fit the outlet, have a proper outlet installed by a qualified electrician.
GROUNDED TOOLS: TOOLS WITH THREE PRONG PLUGS
1. Tools marked with “Grounding Required” have a three wire cord and three prong
grounding plug. The plug must be connected to a properly grounded outlet. If the
tool should electrically malfunction or break down, grounding provides a low
resistance path to carry electricity away from the user, reducing the risk of electric
shock.
For technical questions, please call 1-800-444-3353;
Troubleshooting section at end of manual.
Page 9SKU 93804
2. The grounding prong in the plug is connected through the green wire inside the
cord to the grounding system in the tool. The green wire in the cord must be the only
wire connected to the tool’s grounding system and must never be attached to an
electrically “live” terminal.
3. Your tool must be plugged into an appropriate outlet, properly installed
electrician
and grounded in accordance with all codes and ordinances.
EXTENSION CORDS
AN EXTENSION CORD MUST NEVER BE USED WITH THIS ITEM. Use of an
extension cord could result in damage to the item or fire.
SYMBOLOGY
Double Insulated
Canadian Standards
Association
Underwriters Laboratories,
Inc.
V ~
A
Volt s Alternating Current
Amperes
by a certified
no
xxxx/min.
No Load Revolutions per
Minute (RPM)
UNPACKING
When unpacking both boxes, check to make sure all the parts shown on the Parts Lists
on pages 28 through 32 are included. If any parts are missing or broken, please call
Harbor Freight Tools at the number shown on the cover of this manual as soon as possible.
For technical questions, please call 1-800-444-3353;
Troubleshooting section at end of manual.
Page 10SKU 93804
ASSEMBLY INSTRUCTIONS
WARNING!
Always turn off the Welder and unplug the unit from its electrical
outlet prior to performing any assembly, maintenance, or service.
TO ATTACH THE WHEELS
Attach the
four
Swivel Wheels (15A) at the front and at the rear of the Base (2A) of
the unit, using the Bolts, Lock Washers, and Washers provided.
(See Assy. Diagram, page 28.)
TO INSTALL THE WIRE SPOOL
1. Use the Handle (5A) and lift the Door (6A) of the Welder to expose the Wire Feed
Assembly. (See Figure D.)
(2B)
BRAKE
WASHER
(5B)
WELDING
WIRE
SPOOL
(4B)
RETAINING
SPOOL RING
(2B)
NUT
(1B)
NUT
(1B)
FIGURE D
THREADED
SHAFT
RETAINING
SPOOL RING
(2B)
SPRING
(3B)
RETAINING
SPOOL RING
2. Unscrew and remove the two Nuts (1B) from the Threaded Shaft. Then, pull out and
remove the
3. Insert the Spool (4B) onto the
Spool’s Welding Wire unwinds from the
outer
Retaining Spool Ring (2B). (See Figure D.)
inner
Retaining Spool Ring (2B), making sure the
bottom (clockwise). (See Figure D.)
4. Insert the outer Retaining Spool Ring (2B) into the Spool (4B). Then, firmly screw
the two Nuts (1B) back onto the Threaded Shaft. (See Figure D.)
For technical questions, please call 1-800-444-3353;
Troubleshooting section at end of manual.
Page 11SKU 93804
Loading...