3 in 1 JUMPSTARTER/ AIR COMPRESSOR
39954
Set up And Operating Instructions
Visit our website at: http://www.harborfreight.com
Read this material before using this product. Failure to do so can result in serious injury. Save this manual.
Copyright© 1999 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. Tools required for assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
Manual Revised 06d, 08j , 09d
|
|
Specifications |
|
|
|
|
|
|
Battery Type |
Sealed, lead-acid, rechargeable, 17 Ah |
|
|
Power Output |
12 VDC, 900 amps peak; 400 amps starting power |
|
|
Cables |
Rubber insulated (#4) copper; 400 amp clamps |
|
|
Compressor |
260 PSI maximum pressure |
|
|
Output Socket |
12 VDC Cigarette lighter output |
|
|
Features |
• Overload protection |
|
|
|
• Automatic charge cutoff (at 14.5~15.5 volts) to help |
|
|
|
prevent overcharging |
|
|
|
• Inflating Needle and Air Raft Tips |
|
Note: Performance of this unit may vary depending on variations in local line voltage.
Save This Manual
You will need the manual for the safety warnings and precautions, assembly instructions, operating and maintenance procedures, parts list and diagram. Keep your invoice with this manual. Write the invoice number on the inside of the front cover. Keep the manual and invoice in a safe and dry place for future reference.
Safety Warnings and Precautions
WARNING: When using tool, basic safety precautions should always be followed to reduce the risk of personal injury and damage to equipment.
Read all instructions before using this tool!
1.Wear eye protection. When working on or around lead-acid batteries, always wear ANSI-approved eye protection.
2.Avoid contact with Battery Acid. If splashed, immediately wash effected area with clean water. Continue washing area until medical help arrives.
3.Connect cables to proper polarities. Connect RED POSITIVE (+) cable to Positive
BatteryTerminal first. ConnectBLACK NEGATIVE (-) cable to body ground(a non moving metal part) second. Do not connect the BLACK NEGATIVE (-) cable to the Negative Battery Terminal. Turn vehicle ignition off before making cable connections.
4.Use this tool in well ventilated areas. Do not attempt to jump start vehicle around flammable gases or liquids.
5.Do not allow the Black and Red clamps to touch. If this happens it can melt clamps or other metal objects. Place them only on the corresponding terminals.
6.12 Volt Systems Only. Use only with vehicles and boats with 12 volt electrical systems.
7.For emergency use only. Do not use this system in the place of a vehicle battery. Only use to jump start your vehicle.
8.Avoid working alone. If an accident happens, an assistant can bring help.
REV 08b, 08k
SKU 39954 For technical questions, please call 1-800-444-3353. |
Page 2 |
9.Avoid electrical shock. Use extreme caution when clamping around uninsulated conductors or bus bars. Prevent body contact with grounded surfaces such as pipes, radiators, ranges, and cabinet enclosures when testing voltages.
10.Keep work area clean. Cluttered areas invite injuries.
11.Avoid damaging Jumpstarter System. Use only as specified in this manual.
12.Observe work area conditions. Do not use tool in damp or wet locations. Don’t expose to rain. Keep work area well lighted.
13.Keep children away. Children must never be allowed in the work area. Do not let them handle machines, tools, or extension cords.
14.Store idle equipment. When not in use, tools must be stored in a dry location to inhibit rust. Always lock up tools and keep out of reach of children.
15.Do not place this unit in direct sunlight, direct heat or moisture.
16.Dress properly. Do not wear loose clothing or jewelry as they can be caught in moving parts. Protective, electrically nonconductive clothes and nonskid footwear are recommended when working. Wear restrictive hair covering to contain long hair.
17.Use eye and ear protection. Always wear ANSI-approved impact safety goggles.
18.Do not overreach. Keep proper footing and balance at all times. Do not reach over or across electrical cables or frames.
19.Maintain tools with care. Inspect tool cords periodically and, if damaged, have them repaired by an authorized technician.
20.Stay alert. Watch what you are doing, use common sense. Do not operate any tool when you are tired.
21.Check for damaged parts. Before using any tool, any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment and binding of moving parts; any broken parts or mounting fixtures; and any other condition that may affect proper operation. Any part that is damaged should be properly repaired or replaced by a qualified technician. Do not use the tool if any switch does not turn On and Off properly.
22.Replacement parts and accessories. When servicing, use only identical replacement parts. Use of any other parts will void the warranty. Only use accessories intended for use with this tool. Approved accessories are available from Harbor Freight Tools.
23.Do not operate tool if under the influence of alcohol or drugs. Read warning labels on prescriptions to determine if your judgment or reflexes are impaired while taking drugs.
If there is any doubt, do not operate the tool.
24.People with pacemakers should consult their physician(s) before use. Electromagnetic fields in close proximity to heart pacemaker could cause pacemaker interference or pacemaker failure.
25.The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator.
SKU 39954 For technical questions, please call 1-800-444-3353. |
Page 3 |