User Manual
Table of Contents
1. Before You Begin ........................................................................... 3
What Is Included ........................................................................................... 3
Unpacking Instructions .................................................................................. 3
Claims ........................................................................................................... 3
Text Conventions .......................................................................................... 3
Icons .............................................................................................................. 3
Document Information ................................................................................... 3
Product at a Glance ...................................................................................... 4
Safety Notes .................................................................................................. 4
2. Introduction .................................................................................... 5
Product Overview .......................................................................................... 5
Product Dimensions ...................................................................................... 6
3. Setup ............................................................................................... 7
AC Power ...................................................................................................... 7
Fuse Replacement ................................................................................................. 7
Mounting ....................................................................................................... 8
Orientation ............................................................................................................. 8
Rigging ................................................................................................................... 8
4. Operation ........................................................................................ 9
Control Panel Operation................................................................................ 9
Fluid Tank Indicator LEDs ............................................................................. 9
Wired Timer Remote Operation .................................................................. 10
Menu Map ................................................................................................... 11
Configuration (DMX) ................................................................................... 11
Starting Address .......................................................................................... 11
Configuration (Standalone Mode) ............................................................... 12
Manual Mode ....................................................................................................... 12
DMX Channel Assignments and Values ..................................................... 12
2-CH ..................................................................................................................... 12
5. Technical Information .................................................................. 13
Hazer Maintenance ..................................................................................... 13
Storage ........................................................................................................ 13
General Troubleshooting............................................................................. 14
Returns .............................................................................................. 15
Contact Us ........................................................................................ 15
Page 2 of 16 Hurricane™ Haze 2D User Manual Rev. 12
6. Technical Specifications .............................................................. 16
1. Before You Begin
What Is
Unpacking
Instructions
Immediately upon receiving this product, carefully unpack it and check the container in
Claims
For other issues such as missing components or parts, damage not related to
Text
Conventions
<Menu>
A key to be pressed on the product’s control panel
1–512
A range of values
50/60
A menu option not to be modified (for example, showing the
operating mode/current status)
Menu > Settings
A sequence of menu options to be followed
ON
A value to be entered or selected
Icons
Document
The information and specifications contained in this document are subject to change
assumes no responsibility or liability for any errors or
Author
Date
Editor
Date
• Hurricane™ Haze 2D
Included
• Power Cord
• Timer Remote (15 ft length)
• Warranty Card
• Quick Reference Guide
which you received it.
If the container or the material inside the container (the product and included
accessories) appear damaged from shipping, or show signs of mishandling, upon
receipt notify the carrier immediately, not Chauvet. Failure to do so in a timely manner
may invalidate your claim with the carrier. In addition, keep the container and all the
packing material for inspection.
shipping, or concealed damage, file a claim with Chauvet within seven (7) days of
receiving the merchandise.
Information
Convention Meaning
A set of values of which only one can be chosen
Settings
Icon Meaning
Critical installation, configuration, or operation information.
Failure to comply with this information may render the
product partially or completely inoperative, cause damage
to the product, or cause harm to the user.
Important installation or configuration information. Failure
to comply with this information may prevent the product
from functioning correctly.
Useful information.
without notice. Chauvet
omissions that may appear in this manual.
© Copyright 2014 Chauvet. All rights reserved.
Electronically published by Chauvet in the United States of America.
A. Leon 10/30/14 M. Trouard 10/30/14
Hurricane™ Haze 2D User Manual Rev. 12 Page 3 of 16
Product at a
Glance
x
x
Outdoor Use
x
Auto-ranging Power Supply
x
Sound-Activated
x
Replaceable Fuse
P
DMX
P
User-Serviceable
x
Master/Slave
x
Duty Cycle
x
Safety Notes
between cleanings, to increase the life of your product.
Use on Dimmer
Please read the following Safety Notes carefully before working with the
product. The Notes include important safety information about installation,
usage, and maintenance.
• Always connect the product to a grounded circuit to avoid the risk of electrocution.
• Always disconnect this product from the power source before cleaning it or
replacing the fuse.
• Make sure the power cord is not crimped or damaged.
• Never disconnect the power cord by pulling or tugging on the cord.
• Do not touch the output nozzle on this product. It is very hot during operation and
it may remain hot for several hours after turning the unit off.
• If mounting this product overhead, always secure it to a fastening device using a
safety cable.
• Do not mount this product on a flammable surface (e.g., wood, linoleum, carton,
plastic, or carpet).
• Always make sure that the voltage of the outlet to which you ar e conne cti ng the
product is within the range stated on the decal or rear panel of the product.
• Keep this User Manual for future consultation. If you sell this product to another
user, be sure that they also receive this document.
• This product is for indoor use only! To prevent risk of fire or shock, do not expose
this product to rain or moisture.
• Make sure there are no flammable materials close to the unit while operating.
• Always install this product in a location with adequate ventilation, at least
20 in (50 cm) from adjacent surfaces.
• Be sure that no ventilation slots on the unit’s housing are blocked.
• Make sure to replace the fuse with another of the same type and rating.
• The maximum ambient temperature (Ta) is 104 °F (40 °C). Do not operate this
product at higher temperatures.
• In the event of a serious operating problem, stop using the unit immediately.
• Never try to repair this product. Repairs carried out by unskilled people can lead
to damage or malfunction. Please contact the nearest authorized techni ca l
assistance center.
• Never connect this product to a dimmer pack.
• Make sure there are no flammable materials close to the unit while operating.
• Depending on the amount of fog/haze generated, all fog machines may set off
smoke detectors.
• Do not use for space heating purposes.
• Use only CHAUVET® water-based haze fluid.
• Drain the tank before transporting the product.
• To eliminate unnecessary wear and improve its lifespan, during periods of non-
use completely disconnect the product from power via breaker or by unplugging it.
FCQ (Fog Cleaner Quart) was specifically developed by Chauvet to clean your
Hurricane™ Haze 2D. Make sure you use FCQ regularly, no longer than 90 days
Auto Programs
Page 4 of 16 Hurricane™ Haze 2D User Manual Rev. 12
2. Introduction
Product Overview
Control Board
DMX In
DMX Out
Wired Remote
Power In
Fuseholder
Power Switch
Rubber feet (4)
Fluid & wired remote
storage access panel
Hurricane™ Haze 2D User Manual Rev. 12 Page 5 of 16
Product Dimensions
Page 6 of 16 Hurricane™ Haze 2D User Manual Rev. 12
3. Setup
AC Power
(circuit breaker or fuse),
an appropriate electrical ground to avoid the risk of
a rheostat (variable resistor) or dimmer circuit,
Fuse Replacement
with a fuse of the exact
The product does not ship with a spare fuse; however, the safety cap has room
Spare fuse holder
(inside safety cap)
Installed fuse (held
by plastic clip)
Safety cap
This product can work with an input voltage of either 120 VAC, 60 Hz or
230 VAC, 50 Hz depending on the model.
To determine the power requirements for a particular product, see the label affixed to
the back plate of the product or refer to the product’s specifications chart. The listed
current rating indicates the product ’s average current draw under normal conditions.
Always connect this product to a protected circuit
making sure that it has
electrocution or fire.
Never connect this product to
even if the rheostat or dimmer channel serves only as a 0 to 100% switch.
Disconnect this product from the power outlet before replacing the fuse.
1. Wedge the tip of a flat-head screwdriver into the slot of the fuse holder.
2. Pry the fuse out of the housing.
3. Remove the blown fuse from the holder and replace
same type and rating.
4. Insert the fuse holder back in place and reconnect power.
for a spare.
Hurricane™ Haze 2D User Manual Rev. 12 Page 7 of 16
Mounting
Orientation
provided there is
Rigging
to a rigging point, whether an elevated
Bracket Knob (2)
Mounting Bracket
Safety cable
Safety Cable
The Hurricane™ Haze 2D may be mounted in any position
adequate room for ventilation around it.
Be sure that the structure or surface onto which you are mounting this product can
support its weight. Please see the Technical Specifications section of this manual
for weight information.
Make sure to mount the product securely
platform or a truss.
When rigging this product onto a truss, you should use a mounting clamp of
appropriate weight capacity. The bracket has a 13 mm hole, which is appropriate
for this purpose.
When mounting this product overhead, always use a safety cable.
Before deciding on a location for this product, always make sure tha t it will be easy
to access the unit for maint en a nce and programming purposes.
When po wer linki ng multi ple products, you must always consider the length of the
power linking cable and mount the products close enough for the cable to reach
them.
The bracket knobs allow for directional adjustment when aiming the product to the
desired angle. Only loosen or tighten the bracket knobs using your bare hands.
Using tools could damage the knobs.
Mounting Diagram
Page 8 of 16 Hurricane™ Haze 2D User Manual Rev. 12
4. Operation
Control
Operation
Important note regarding the priority level for the three types of methods used
3. Remote controller
Fluid Tank
Indicator
Note: The Hurr ic an e ™ Haze 2D may be operat io nal wh il e the heater is warming up.
To access the control panel functions, use the three buttons located underneath the
Panel
display.
Button Function
<MENU>
Press to scroll through the
operating modes
<UP>
<DOWN>
to control the operation of your Hurricane™ Haze 2D.
If using the remote control and the digital display is touched, the digital display will
take priority control. If using the digital display, and then connect the product to a
DMX controller, the DMX will take priority control. The priority control levels are:
1. DMX
2. Digital display
Indicator LEDs show the status of the fill tank, as follows:
• Red - the heater is currently warming up
LEDs
• Flashing Red - the heater is currently warming up and requires refilling
• Blue - the hazer is ready
• Flashing Blue - the heater is warmed but the fluid tank requires refilling
See the General Troubleshooting section to identify possible sources of trouble
and find solutions.
Press to find a higher value
Press to find a lower value
Hurricane™ Haze 2D User Manual Rev. 12 Page 9 of 16
Wired Timer
Operation
Interval
Adjustment
Timer LED
Manual
LED
Manual/Power
LED
Manual Control
Continuous
Timer On/Off
Latching Button
Duration
Output
OUTPUT
Important: Using the Control Board, set the Fan and Haze output to 0. You can then
Remote
The wired timer c ontr oller a llows you to automaticall y trigg er f og out put b y set ti ng inter v al and durat io n
times. LED indicator lights displa y the m achine and control ler’s c urrent st ate. Rotar y knobs set inter va l
and duration times, while manual and continuous buttons allow overriding control.
1. Plug in the fog machine to power and turn the power switch to the product on.
2. Plug in the timer controller to the Manual Controller socket on the back of the fog machine.
3. Press the <TIMER ON/OFF> latching button on the timer controller. The Timer LED Indicator
above the button will light up. The <TIMER ON/OFF> latching button will remain on until it is
pressed again.
4. Set the INTERVAL, DURATION, and OUTPUT adjustment knobs to the desired positions.
• INTERVAL knob sets the amount of time in between bursts of fog
• DURATION knob sets the length of time that the fog machine will run during the burst
• OUTPUT knob adjusts the fog output
connect and operate the included wired remote with the Hurricane™ Haze 2D.
5. Press the <CONTINUOUS> latching button and the fog machine outputs fog until the button is
pressed again. The Manual/Power LED Indicator above the button will light up during
continuous operation.
Note: The duration of continuous fog output is based on the capability of the fog
machine.
6. Press the <MANUAL> button to momentarily output fog. The fog machine will output fog for
as long as you hold down the button. During manual operation the Manual Momentary LED
Indicator above the button will light up.
Note: The duration of manual fog output is based on the capability of the fog machine.
Adjustment
Adjustment
Indicator
Momentary
Momentary Button
Latching Button
Page 10 of 16 Hurricane™ Haze 2D User Manual Rev. 12
Menu Map
Mode
Programming Steps
Description
Configuration
cable from the DMX output of the DMX controller to the
Starting
channel mode for basic
When selecting a starting DMX address, always consider the number of DMX
channels the selected DMX mode uses. If you choose a starting address that is too
DMX Mode d*** 001–512
Manual Mode
Set this product in DMX mode to control it with a DMX controller.
(DMX)
• Connect this product to a suitable power outlet.
• Turn this product on.
• Connect a DMX
The Hurricane™ Haze 2D has one DMX personality, a 2-
Address
control.
The Hurricane™ Haze 2D uses up to two channels in its 2-channel DMX mode, which
defines the highest configurable address to 511.
high, you could restrict the access to some of the product’s channels.
If you are not familiar with the DMX protocol, download the DMX Primer from
www.chauvetlighting.com
To select the starting address, do the following:
1. Press <MENU> repeatedly until d*** shows on the display.
2. Use <UP> or <DOWN> to select the starting address.
Haze Volume h001–h005
Blower Speed f001–f005
DMX input socket of this product.
.
Selects the DMX starting address
Low–high
Low–high
Hurricane™ Haze 2D User Manual Rev. 12 Page 11 of 16
Configuration
Mode)
Manual Mode
that is operating in any standalone mode, whether
DMX signals that could interfere
DMX Channel Assignments and V alues
2-CH
000 ó 005
Off 006 ó 075
Level 1
076 ó 125
Level 2
126 ó 165
Level 3 166 ó 185
Level 4
186 ó 255
Level 5
000 ó 038
Off 039 ó 069
Level 1 070 ó 101
Level 2
102 ó 132
Level 3 133 ó 187
Level 4
188 ó 255
Level 5
(Standalone
Set this product in one of the standalone modes to control it without a DMX controller.
1. Connect this product to a suitable power outlet.
2. Turn this product on.
Never connect a product
Static, Automatic, or Sound to a DMX string connected to a DMX controller.
Products in standalone mode may transmit
with the DMX signals from the controller.
To enable the Automatic Mode, follow the instructions below:
1. Press <MENU> repeatedly until h*** shows on the display.
2. Use <UP> or <DOWN> to adjust the haze volume.
3. Press <MENU> repeatedly until f*** shows on the display.
4. Use <UP> or <DOWN> to adjust the blower speed.
Channel Function Value Setting
1 Blower speed
2 Haze volume
Page 12 of 16 Hurricane™ Haze 2D User Manual Rev. 12
5. Technical Information
Hazer Maintenance
hours of continuous
between cleanings, to increase the life of your product.
Storage
on a monthly basis to achieve the best
Do not allow the hazer to become clogged. After every 40
operation, use CHAUVET® Fog Cleaner Quart (FCQ) through the system to prevent
the accumulation of particulate matter in the heating element.
The recommended cleaning procedure is as follows.
1. Unplug the product from power.
2. Empty all fog fluid from the machine.
3. Add cleaning solution to the tank.
4. Connect the product to power and allow it to warm up.
5. Run the unit in a well-venti late d area until the ta nk is almost empty . Do not
allow the pump to run dry.
6. Refill with hazer fluid to continue using the hazer. Run the machine briefly to
clear any remaining cleaning solution from the pump and heater.
Do not operate the machine without fluid at any time.
Fog Cleaner Quart (FCQ) was specifically developed by Chauvet to clean your
Hurricane™ Haze 2D. Make sure you use FCQ regularly, no longer than 90 days
Before storing the hazer, run FCQ through the system as described in the cleaning
procedure above; however, only follow steps 1 through 5. Do not refill the tank with
fog fluid if storing the hazer. Cleaning the system prior to storage will help prevent
any particles from condensing inside the pump or heater while not in use.
Test-run your Hurricane™ Haze 2D
performance.
Hurricane™ Haze 2D User Manual Rev. 12 Page 13 of 16
General Troubleshooting
Allow the product to warm up completely. This should take less than 10
Allow the product to warm up completely.
Turn fog machine 45° to flatten out the bubble and allow the fog fluid to
Turn off the product for 5 seconds, and then turn it back on. Repeat as
Note: After more than 10 attempts, contact Customer Service.
Clean thoroughly with CHAUVET® FCQ. For full instructions, see Hazer
Blocked pipes
Contact Customer Service
Failing part
Contact Customer Service
Clean thoroughly with CHAUVET® FCQ. For full instructions, see Hazer
Maintenance. Refill with CHAUVET® water-based haze fluid.
Failing part
Contact Customer Service
Maintenance. Refill with CHAUVET® water-based haze fluid.
Blocked pipes
Contact Customer Service
Failing part
Contact Customer Service
Normal
Blue
Normal
Normal function
circuit
nominal current
Short circuit along the
Change to another outlet
Loose or damaged power
Blown fuse
Replace blown fuse with a goo d one of the same type and rating
Internal problem
Send product for repair
Use the right fader(s) on the controller
Wrong DMX person al it y on
Set the correct DMX product’s personality
the DMX controller
Loose or damaged DMX
Internal problem
Send product for repair
Interference with AC or
radio signals
Too many products
connected
Terminator not connected
Install a terminator, as indicated in the “DMX Primer” section.
If you still experience problems after trying the solutions presented here, contact Chauvet
Symptom Indicator Status Possible Cause Possible Action
No output or short output
Spitting fluid
Circuit breaker or fuse
keeps blowing
Red Heater warming up
Red flashing Air bubble in fluid line
Incorrect fluid
Blue
Incorrect fluid
Blue blinking
Blue
N/A
Blocked pipes Contact Customer Service
Incorrect fluid
Excessive load on the
power lines
No energy on power outlet
minutes.
flow properly
necessary.
Maintenance. Refill with CHAUVET® water-based haze fluid.
Clean thoroughly with CHAUVET® FCQ. For full instructions, see
Make sure that the total load do es not e xce ed 80% of t he br eak er or fuse
Check the power lines and power cords
Check power outlet
Hazer
Product does not power
up
Product does not respond
to DMX
Blue
Intermittent DMX
Problems
Technical Support.
cord
Wrong starting address on
the product
the product
Wrong polarity setting on
cable
Signal cables are not DMX
compatible
DMX cable too long
Check the power cord
Set the correct starting address on the product
Assign the faders accordingly
Change the signal polarity on the controller
Check the DMX cable before the faul t y unit
Replace non DMX cables with tr ue D M X cabl es
Keep DMX cables away from AC wires or radio equipment
Install an optically coupled DMX amplifier right before the product with
intermittent problems
Install an optically coupled DMX amplifier after unit #32
Page 14 of 16 Hurricane™ Haze 2D User Manual Rev. 12
R
To return a product or request support:
distributors outside the U.S., United Kingdom, Ireland, or Mexico.
contact your distributor
products to them.
Call the corresponding Chauvet Technical Support office and request a Return Merchandise Authorization (RMA)
Clearly label the package with the RMA number. Chauvet will refuse any product returned without an RMA number.
Before sending the product, clearly write the following information on a piece of paper and place it inside the box:
responsibility. FedEx packing or double-boxing is recommended.
reserves the right to use its own discretion to repair or replace returned
C
WORLD HEADQUARTERS - Chauvet
General Information
Toll free: (800) 762-1084
Technical Support
World Wide Web www.chauvetlighting.com
UNITED KINGDOM AND IRELAND - Chauvet Europe Ltd.
General Information
Fax: +44 (0)1773 511110
Technical Support
MEXICO - Chauvet Mexico
General Information
Voice: +52 (728) 285-5000
Technical Support
Outside the U.S., United Kingdom, Ireland, or Mexico, contact your dealer. Follow their instructions to request support or
to return a product. Visit our website for contact details.
ETURNS
• In the U.S., contact Chauvet World Headquarters (see Contact Us).
• In the UK or Ireland, contact Chauvet Europe Ltd. (see Contact Us).
• In Mexico, contact Chauvet Mexico (see Contact Us).
• In any other country, DO NOT contact Chauvet. Contact your distributor. See www.chauvetlighting.com for
If you live outside the U.S., United Kingdom, Ireland, or M exico,
of record and follow their instructions on how to return Chauvet
Visit our website for contact detai ls.
number before shipping the product. Be prepared to provide the model number, serial number, and a brief description of
the cause for the return.
You must send the merchandise prepaid, in its original box, and with its original packing and accessories. Chauvet will
not issue call tags.
Write the RMA number on a properly affixed label. DO NOT write the RMA number
directly on the box.
• Your name
• Your address
• Your phone number
• RMA number
• A brief description of the problem
Be sure to pack the product properly. Any shipping damage resulting from inadequate packaging will be your
Chauvet
product(s).
ONTACT US
Address:5200 NW 108th Avenue
Sunrise, FL 33351
Voice: (954) 577-4455
Fax: (954) 929-5560
Address:Unit 1C
Brookhill Road Industrial Estate
Pinxton, Nottingham, UK
NG16 6NT
Voice: +44 (0)1773 511115
Address:Av. Santa Ana 30
Parque Industrial Lerma
Lerma, Mexico C.P. 52000
Hurricane™ Haze 2D User Manual Rev. 12 Page 15 of 16
Voice: (954) 577-4455 (Press 4)
Fax: (954) 756-8015
Email: tech@chauvetlighting.com
Email: uktech@chauvetlighting.com
World Wide Web www.chauvetlighting.co.uk
Email: servicio@chauvet.com.mx
World Wide Web www.chauvet.com.mx
6. Technical Specifications
Dimensions and
Length
Width
Height
Weight
11.2 in (285 mm)
10.5 in (267 mm)
13.7 in (350 mm)
18.7 lb (8.5 kg)
Note: Dimensions in inches rounded to the nearest decimal digit.
Power
Power Supply Type
Range
Voltage Selection
120 V, 60 Hz
230 V, 50 Hz
Parameter
120 V, 60 Hz
230 V, 50 Hz
Consumption
533 W (4.4 A)
533 W (2.3 A)
Fuse size
F 7, 250 V
F 5, 250 V
Power I/O
Input
Connectors
IEC
Cord plug
Edison
Operation
Heat-up Time
Tank Capacity
Fluid Consumption
5 min
2.5 l
8.2 ml/min
Fog output
Ft3/min (m3/min)
1,200 (34)
Approved Fluids
Chauvet® Haze Fluid
(Gallon)
HFG
Thermal
Maximum External Temp.
Cooling System
104 °F (40 °C)
Convection
DMX
I/O Connectors
Connector Type
Channel Range
3-pin XLR
Sockets
2
Ordering
Product Name
Item Code
Item Number
05070344 (120 V)
05070389 (230 V)
HHAZE2D
220VHHAZE2D
Weight
Model-specific
or
Fixed voltage
Hurricane™ Haze 2D
Page 16 of 16 Hurricane™ Haze 2D User Manual Rev. 12
UL 499
CSA C22.2 No. 64
Loading...