Stainless steel split door design. The top half
rises while the lower half folds down to
provide a space saving drain table.
Spray Arm Assembly
Stainless steel spray arm assemblies, with
stainless steel jets and quick-release
mechanism for easy cleaningandreassembly.
Filter
Perforated, removable, stainless steel basket.
Water Pump
7-1/2 Hp, 208/240 or 440/480 volt, 1 phase or
3 phase, 60 cycle with output of 120 gallons
per minute at 35 to 45 P.S.I.
Digital Control& Information Center
12 volt control circuit with push pad
operation of “power on,”“stop”and “short,
medium or long wash cycles.” A digital
display indicates “time remaining” for each
cycle. LED’s indicate wash, rinse and unload
functions. A buzzer is also included to
provide an audible indication of time to
unload. Pre-programmed circuit board
allows the push pad to be used as a
“diagnostic center” by displaying “error
codes” for ease of troubleshooting.
Gauges
Special moisture resistant design, measures
wash temperature, rinse temperature and
wash jet pressure.
WashTank
Stainless steel with electric infrared, gas,
steam or steam coil heating, thermostatically
controlled, low-water protected, sloped to
drain with a 36-gallon capacity (27 gallons
if infrared gas heated)
RinseTank
Stainless steel with electric, infrared gas or
steam coil heating to provide 180°F/190°F
hot sanitizing rinse. Uses 5 gallons per
27-second cycle.
Racks
Stainless steel rod, built to match specific
washing requirements.
Due to an ongoing value analysis program at Champion, specifications contained in this catalog are subject to change without notice.
Champion Industries, Inc., P. O. Box 4149, Winston-Salem, NC 27115 • 336/661-1556 • Fax: 336/661-1979 • www.championindustries.com
2674 N. Service Road, Jordan Station, Ontario, Canada L0R 1S0 • 800/263-5798 • Fax: 905/562-4618
SPECIFICATIONS
MODEL SD-20 POT, PAN &
UTENSIL WASHER
WasherAutomatic washing machine designed to wash all pots, pans and utensils commonly used
in baking and cooking operations.
Cabinet50" wide x 36" deep x 71-1/8" high. Overall height with door open: 87-5/8". Door opening:
40" wide x 28-1/2" high. Constructed of 12, 14 & 16 gauge, type 304 #3 finish, stainless
steel. All seams tig-welded, cleaned and polished.
DoorFront-loading, split door design for easy loading and unloading. The top half of the door
system rises while the lower half folds down to create a space saving drain table. Door is
interlocked with proximity switch to prevent machine operation while door is open. Door
construction: 16 gauge, type 304 #3 finish, stainless steel.
Recirculating WashTankHeated by 12kW total 208/240, 480 or optional 575 volt electric immersion heaters,
thermostatically controlled 150°F wash temperature and low water protection system.
36 gallons (27 gallons if infrared heated), 14 gauge stainless steel, sloped to drain. Infrared
gas and steam heating options available.
Wash Tank FilterPerforated, stainless steel basket type, double filter system for increased effectiveness and
easy cleaning without emptying wash tank.
Wash Tank Fill ValveSize 1/2" brass material, solenoid type, automatic.
Wash Tank Drain ValveSize 1-1/4" brass material, gate type for manual or electrically operated ball valve
for automatic option.
Wash Pump7-1/2 hp, 208/240, 480 or optional 575 volt, 3 phase, 60 cycle. Close coupled; 120 gallons
per minute at 35 to 45 psi, mounted on 12 gauge stainless steel formed channel base.
Spray Arm AssembliesWater driven, stainless steel spray arm assemblies, with stainless steeljets and quick-release
mechanism for easy cleaning and reassembly.
Sanitizing Rinse TankStainless steel, 10 gallon capacity, with 12kW total 208/240, 480 or optional 575 volt
electric booster heater to provide 180°-190°F hot sanitizing rinse. Uses 5 gallons per
27 second cycle. Infrared gas and steam coil heating options available.
Final Rinse PipingType 304 stainless steel tubing with brass compression fittings and brass or optional
stainless steel full cone rinse jets.
Control& Information Center12 volt control circuit with push pad operation of “Power On,” “Stop”and “Short, Medium
or Long Wash Cycles.” A digital display indicates “Time Remaining” for each cycle. LED’s
indicated wash, rinse and unload functions. A buzzer is also included to provide an audible
indication when the machine is ready to unload. A pre-programmed circuit board allows
the push pad to be used as a “Diagnostic Center”by displaying“Error Codes” for ease of
troubleshooting. Moisture resistant gauges measure Wash Temperature, Wash Pressure
and Rinse Temperature.
External Rinse HoseExternally mounted rinse hose with spray gun for easy cleaning and maintenance
of machine.
Steam Exhaust VentSteam exhaust vent 6-3/4" I.D., consisting of 16 gauge rolled collar for PVC pipe
connection bolted to the top of the machine. Machine pre-wired with control timer
for the addition of a fan.
2674 N. Service Road,
Jordan Station, Ontario, Canada L0R 1S0
Tel: 800/263-5798 Fax: 905/562-4618
(2M) 3/05 Printed in U.S.A.
Champion Industries, Inc.
P. O. Box 4149, Winston-Salem, NC 27115
Tel: 336/661-1556 Fax: 336/661-1979
www.championindustries.com
SPECIFICATIONS
MODEL SD-20 POT, PAN &
UTENSIL WASHER
Optional Exhaust FanDraft inducer fan side mounted on exhaust duct to extract excess steam after final rinse
RacksCustomized to hold your specific items. Standard bakery racks include utensil basket with
(2) hold-down lids and (2) bun/sheet pans insert designed to hold (10) pans, constructed
of stainless steel rod, mig-welded.
ConnectionsWater Inlet: 120°F, 3/4" NPT
Water Drain and Overflow: 1-1/4" NPT
Electrical: Two point connection (except 575 volt) through knock out on
electrical enclosure.
Steam Heating Option: 1/2" NPT
Natural or Propane Gas Heating Option: 1/2" NPT
WeightCrated: 1,100 lbs. Uncrated: 850 lbs.
NOTE: All weights are approximate. Weights will vary depending on the number of options
included with the machine.
Services120 Volt -1 phase, 5 running amps, 15 amp service, plus one of the following: