Chamberlain WD822KD User Manual

GARAGE DOOR OPENER

Model WD822KD 1/2 HP

For Residential Use Only

The Chamberlain Group, Inc.

845 Larch Avenue

Elmhurst, Illinois 60126-1196

www.chamberlain.com

Owner’s Manual

■

Please read this manual and the enclosed safety materials carefully!

■

Fasten the manual near the garage door after installation.

■

The door WILL NOT CLOSE unless The Protector System® is connected and properly aligned.

■

Periodic checks of the opener are required to ensure safe operation.

■

The model number label is located on the left side panel of your opener.

Introduction 2-7

Safety symbol and signal word review . . . . . . . . . . . . . . . 2

Preparing your garage door . . . . . . . . . . . . . . . . . . . . . . . 3

Tools needed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Planning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5

Carton inventory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Hardware inventory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Assembly 8-11

Assemble the rail and install the trolley. . . . . . . . . . . . . . . 8

Fasten the rail to the motor unit and

Install the idler pulley . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Install the belt and attach the belt cap retainer . . . . . . . . 10

Set the tension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Installation 11-26

Installation safety instructions . . . . . . . . . . . . . . . . . . . . 11

Determine the header bracket location . . . . . . . . . . . . . . 12

Install the header bracket . . . . . . . . . . . . . . . . . . . . . . . . 13

Attach the rail to the header bracket . . . . . . . . . . . . . . . . 14

Position the opener. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Hang the opener . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Install the door control . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Install the lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Attach the emergency release rope and handle. . . . . . . . 17

Electrical requirements . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Install The Protector System

Fasten the door bracket. . . . . . . . . . . . . . . . . . . . . . . 23-24

Connect the door arm to the trolley . . . . . . . . . . . . . 25-26

. . . . . . . . . . . . . . . . . . 19-22

Adjustment 27-29

Adjust the travel limits . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Adjust the force. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Test the safety reversal system. . . . . . . . . . . . . . . . . . . . 29

Test The Protector System

. . . . . . . . . . . . . . . . . . . . . . 29

Operation 30-34

Operation safety instructions . . . . . . . . . . . . . . . . . . . . . 30

Using your garage door opener . . . . . . . . . . . . . . . . . . . 30

Using the wall-mounted door control . . . . . . . . . . . . . . . 31

To open the door manually . . . . . . . . . . . . . . . . . . . . . . . 31

Care of your garage door opener . . . . . . . . . . . . . . . . . . 32

Having a problem? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Diagnostic chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Programming 35-36

To add or reprogram a hand-held remote control. . . . . . 35

To erase all codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

3-Button remotes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

To add, reprogram or change

a Keyless Entry PIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Repair Parts 37-38

Rail assembly parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Installation parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Motor unit assembly parts . . . . . . . . . . . . . . . . . . . . . . . 38

Accessories 39

Repair Parts and Service 40

Warranty 40

INTRODUCTION

Safety Symbol and Signal Word Review

This garage door opener has been designed and tested to offer safe service provided it is installed, operated, maintained and tested in strict accordance with the instructions and warnings contained in this manual.

When you see these Safety Symbols and Signal Words on the following pages, they will alert you to the possibility of serious injury or death if you do not comply with the

Mechanical

Electrical

warnings that accompany them. The hazard may come from something mechanical or from electric shock. Read the warnings carefully.

When you see this Signal Word on the following pages, it will alert you to the possibility of damage to your garage door and/or the garage door opener if you do not comply with the cautionary statements that accompany it. Read them carefully.

Preparing your garage door

Before you begin:

• Disable locks.

• Remove any ropes connected to garage door.

• Complete the following test to make sure your garage

door is balanced and is not sticking or binding:

1. Lift the door about halfway as shown. Release the door. If balanced, it should stay in place, supported entirely by its springs.

2. Raise and lower the door to see if there is any binding or sticking.

If your door binds, sticks, or is out of balance, call a trained door systems technician.

Sectional Door

To prevent possible SERIOUS INJURY or DEATH:

• ALWAYS call a trained door systems technician if garage door binds, sticks or is out of balance. An unbalanced garage door may NOT reverse when required.

• NEVER try to loosen, move or adjust garage door, door springs, cables, pulleys, brackets or their hardware, ALL of which are under EXTREME tension.

• Disable ALL locks and remove ALL ropes connected to garage door BEFORE installing and operating garage door opener to avoid entanglement.

To prevent damage to garage door and opener:

• ALWAYS disable locks BEFORE installing and operating the opener.

• ONLY operate garage door opener at 120V, 60 Hz to avoid malfunction and damage.

Stepladder

One-Piece Door

Carpenter’s Level (optional)

Drill

Tape Measure

Drill Bits 3/16", 5/16" and 5/32"

Sockets and Wrench 1/2", 5/8", 7/16", 9/16" and 1/4"

Tools needed

During assembly, installation and adjustment of the opener, instructions will call for hand tools as illustrated below.

Pencil

Wire Cutters

Pliers

Hack Saw

Claw Hammer

Screwdriver

Adjustable End Wrench

Planning

Identify the type and height of your garage door. Survey your garage area to see if any of the conditions below apply to your installation. Additional materials may be required. You may ﬁ nd it helpful to refer back to this page and the accompanying illustrations as you proceed with the installation of your opener.

Depending on your requirements, there are several installation steps which may call for materials or hardware not included in the carton.

•

Installation Step 1 – Look at the wall or ceiling above the garage door. The header bracket must be securely fastened to structural supports.

•

Installation Step 5 – Do you have a ﬁ your garage? If so, a support bracket and additional fastening hardware may be required.

• Installation Step 10 – Depending upon garage construction, extension brackets or wood blocks may be needed to install sensors.

• Installation Step 10 – Alternate ﬂ oor mounting of the safety reversing sensor will require hardware not provided.

nished ceiling in

• Do you have an access door in addition to the garage door? If not, Model 7702CB Emergency Key Release is required. See Accessories page.

• Look at the garage door where it meets the ﬂ oor. Any gap between the ﬂ oor and the bottom of the door must not exceed 1/4" (6 mm). Otherwise, the safety reversal system may not work properly. See Adjustment Step 3. Floor or door should be repaired.

SECTIONAL DOOR INSTALLATIONS

• Do you have a steel, aluminum, ﬁ berglass or glass panel door? If so, horizontal and vertical reinforce ment is required (Installation Step 11).

• The opener should be installed above the center of the door. If there is a torsion spring or center bearing plate in the way of the header bracket, it may be installed within 4 feet (1.2 m) to the left or right of the door center. See Installation Steps 1 and 11.

• If your door is more than 7 feet (2.1 m) high, see rail extension kits listed on Accessories page.

SECTIONAL DOOR INSTALLATION

Horizontal and vertical reinforcement is needed for lightweight garage doors (ﬁ berglass, steel, aluminum, door with glass panels, etc.). See page 23 for details.

Header Wall

Vertical Centerline of Garage Door

Gap between ﬂ oor and bottom of door must not

Safety Reversing Sensor

exceed 1/4" (6 mm).

Torsion Spring

Wallmounted Door Control

Extension Spring

Safety Reversing Sensor

Access Door

FINISHED CEILING

Support bracket & fastening hardware is required. See page 15.

Header Bracket

Header Wall

Garage Door

Garage Door Spring

Door Bracket

Motor unit

Trolley Stop Bolt

Straight Door Arm

CLOSED POSITION

Trolley

Belt

Emergency Release Rope & Handle

Curved Door Arm

Planning (Continued)

ONE-PIECE DOOR INSTALLATIONS

• Generally, a one-piece door does not require reinforcement. If your door is lightweight, refer to the information relating to sectional doors in Installation Step 11.

• Depending on your door’s construction, you may need additional mounting hardware for the door bracket (Step 11).

Without a properly working safety reversal system, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a closing garage door.

• The gap between the bottom of the garage door and the ﬂ oor MUST NOT exceed 1/4" (6 mm). Otherwise, the safety reversal system may NOT work properly.

• The ﬂ oor or the garage door MUST be repaired to eliminate the gap.

ONE-PIECE DOOR WITHOUT TRACK

Header Wall

Gap between ﬂ oor and Safety Reversing Sensor

bottom of door must not

exceed 1/4" (6 mm).

ONE-PIECE DOOR WITH TRACK

FINISHED CEILING

Support bracket & fastening hardware is required. See page 15.

Rail

Access Door

Safety Reversing Sensor

Wall-mounted Door Control

Header Wall

Motor unit

Trolley Stop Bolt

Door Bracket

Header Bracket

Garage Door

CLOSED POSITION

Trolley

Belt

Rail

Straight Door Arm

Curved Door Arm

Emergency Release Rope & Handle

Safety Reversing Sensor

Gap between ﬂ oor and bottom of door must not exceed 1/4" (6 mm).

Access Door

Safety Reversing Sensor

Header Wall

Trolley Stop Bolt

Header Bracket

CLOSED POSITION

Door Bracket

Garage Door

Belt

Curved Door Arm

Straight Door Arm

Trolley

Rail

Emergency Release Rope & Handle

Carton Inventory

Your garage door opener is packaged in one carton which contains the motor unit and all parts illustrated below. Accessories will depend on the model purchased. If anything is missing, carefully check the packing material.

Parts may be stuck in the foam. Hardware for assembly and installation is shown on the next page. Save the carton and packing material until installation and adjustment is complete.

SECURITY✚ 3-Button Remote Control (2)

Trolley

Belt

Rail Front (header) Section

SECURITY✚ Keyless entry

2-Conductor Bell Wire White & White/Red

Motor Unit with 2 Light Lenses

Hanging Brackets

Multi-Function Door Control

Rail Center/Back Sections

Belt Cap Retainer

“U” Bracket

Idler Pulley

Curved Door Arm Section

Door Bracket

Header Bracket

Straight Door Arm Section

Safety Sensor Bracket (2)

The Protector System (2) Safety Reversing Sensors (1 Sending Eye and 1 Receiving Eye) with 2-Conductor White & White/Black Bell Wire attached

Safety Labels

and

Literature

Hardware Inventory

Separate all hardware and group as shown below for the assembly and installation procedures.

ASSEMBLY HARDWARE

Spring/Trolley Nut (1) Nut

Bolt 1/4"-20x1-3/4" (2)

Trolley Threaded Shaft (1)

Lock Nut 1/4"-20 (2)

Lock Washer 3/8" (1)

3/8" (1)

Master Link (2)

INSTALLATION HARDWARE

Carriage Bolt 1/4"-20x1/2" (2)

Lag Screw 5/16"-9x1-5/8" (2)

Wing Nut 1/4"-20 (2)

Hex Bolt 5/16"-18x7/8" (4)

Ring Fastener (3)

Lock Washer 5/16" (7)

Idler Bolt (1)

Nut 5/16"-18 (8)

Insulated Staples (30)

Lag Screw 5/16"-18x1-7/8" (2)

1/4"-14x5/8" (2)

Clevis Pin 5/16"x1-1/2" (1)

Handle Rope

Screw 6ABx1-1/4" (2)

Drywall Anchors (2)Self-Threading Screw

Clevis Pin 5/16"x1" (1)

Screw 6-32x1" (2)

Spacer (2)

Clevis Pin 5/16"x1-1/4" (1)

ASSEMBLY STEP 1

Assemble the Rail & Install the Trolley

To avoid installation difﬁ culties, do not run the garage door opener until instructed to do so.

The front rail has a cut out “window” at the door end (see illustration). The hole above this window is larger on the top of the rail than on the bottom. A smaller hole 3-1/2" (8.9 cm) away is close to the rail edge. Rotate the back rail so it has a similar hole close to the opposite edge, about 4-3/4" (12 cm) from the far end.

1. Remove the straight door arm and hanging bracket packaged inside the front rail and set aside for Installation Step 5 and 12. NOTE: To prevent INJURY

while unpacking the rail carefully remove the straight door arm stored within the rail section.

2. Align the rail sections on a ﬂ at surface as shown and slide the tapered ends into the larger ones. Tabs along the side will lock into place.

To prevent INJURY from pinching, keep hands and ﬁ ngers away from the joints while assembling the rail.

3. Place the motor unit on packing material to protect the cover, and rest the back end of the rail on top. For convenience, put a support under the front end of the rail.

4. As a temporary stop, insert a screwdriver into the hole 10" (25 cm) from the front end of the rail, as shown.

5. Check to be sure there are 4 plastic wear pads inside the inner trolley. If they became loose during shipping, check all packing material. Snap them back into position as shown.

6. Slide the trolley assembly along the rail from the back end to the screwdriver.

Trolley

Idler Pulley Hole

Window Cut-Out

Screwdriver

KEEP LARGER HOLE ON TOP

FRONT RAIL (TOP)

Tabs

Front Rail (TO DOOR)

Tapered End

Back Rails (TO MOTOR UNIT)

Tapered End

Outer Trolley

Tapered End

Inner Trolley

Wear Pads

ASSEMBLY STEP 2

Fasten the Rail to the Motor Unit

• Insert a 1/4"-20x1-3/4" bolt into the cover protection bolt hole on the back end of the rail as shown. Tighten securely with a 1/4"-20 lock nut. Do NOT overtighten.

• Remove the two bolts from the top of the motor unit.

• Place the “U” bracket, ﬂ at side down, on the motor unit and align the bracket holes with the bolt holes. Fasten with the previously removed bolts.

• Align the rail assembly with the top of the motor unit. Slide the rail end onto the “U” bracket, all the way to the

stops that protrude on the top and sides of the bracket.

HARDWARE SHOWN ACTUAL SIZE

Lock Nut 1/4"-20

Bolt 1/4"-20x1-3/4"

ASSEMBLY STEP 3

Install the Idler Pulley

• Lay the belt beside the rail, as shown. Grasp the end with the hooked trolley connector and pass approximately 12" (30 cm) of belt through the window. Keep the ribbed side toward the rail, and allow it to hang until Assembly Step 5.

• Remove the tape from the idler pulley. The inside center should be pre-greased. If dry, regrease to ensure proper operation.

• Place the idler pulley into the window as shown.

• Insert the idler bolt from the top through the rail and pulley. Tighten with a 3/8" lock washer and nut underneath the rail until the lock washer is compressed.

• Rotate the pulley to be sure it spins freely.

• Insert a 1/4"-20x1-3/4" bolt into the trolley stop hole in the front of the rail as shown. Tighten securely with a 1/4"-20 lock nut.

To avoid SERIOUS damage to garage door opener, use ONLY those bolts/fasteners mounted in the top of the opener.

Rail

Trolley Stop Hole

Idler Pulley

Motor Unit Sprocket

Bolt

“U” Bracket

Bolt

Cover Protection Bolt Hole

SLIDE RAIL TO STOPS ON TOP AND SIDES OF BRACKET

Lock Nut

Idler Bolt

Lock Washer 3/8"

Bolts

Screwdriver

Nut 3/8"

Trolley Connector

Pulley

Bolt

Nut

Washer

Grease Inside Pulley

Idler Pulley

Lock Nut

Lock Washer 3/8"

HARDWARE SHOWN ACTUAL SIZE

Lock Nut 1/4"-20

Nut 3/8"

Bolt 1/4"-20x1-3/4"

Idler Bolt

ASSEMBLY STEP 4

Install the Belt and Attach the Belt Cap Retainer

1. Pull the belt around the idler pulley and toward the trolley. The ribbed side must contact the pulley.

2. Hook the trolley connector into the retaining slot on the trolley as shown.

3. With the trolley against the screwdriver, dispense the remainder of the belt along the rail length toward the motor unit and around the sprocket. The sprocket teeth must engage the belt.

4. Check to make sure the belt is not twisted and the FLAT side of the trolley threaded shaft is facing the rail. Connect the trolley threaded shaft with the master link, as illustrated:

• Push pins of master link bar through holes in end of

belt and trolley threaded shaft.

• Push master link cap over pins and past pin notches.

• Slide clip-on spring over cap and onto pin notches

until both pins are securely locked in place.

5. Insert the trolley threaded shaft through the hole in the trolley. Be sure the belt is not twisted and the FLAT side

faces the rail.

6. Hold the belt at the trolley shaft as you thread the spring nut by hand onto the shaft until ﬁ nger tight against the trolley. Do not use any tools.

7. Remove the screwdriver.

8. Position the belt cap retainer over the motor unit sprocket as shown and fasten to the mounting plate with 8x3/8" hex screws provided.

To avoid possible SERIOUS INJURY to ﬁ ngers from moving garage door opener:

• ALWAYS keep hand clear of sprocket while operating opener.

• Securely attach sprocket cover BEFORE operating.

HARDWARE SHOWN ACTUAL SIZE

Spring/Trolley NutHex Screw 8x3/8"

Idler Pulley

Spring Nut

Master Link Clip-On Spring

Master Link Cap

Trolley Connector

Retaining Slot

Hole

Trolley Threaded Shaft

Belt Cap Retainer

Pin Notch

Master Link Bar

Hex Screws #8x3/8"

Motor Unit Sprocket

Mounting Plate

ASSEMBLY STEP 5

WARNING

WARNING WARNING

Set the Tension

• Insert a screwdriver tip into one of the nut ring slots and brace it ﬁ rmly against the trolley.

• Place a 7/16" open end wrench on the square end. Rotate the nut about 1/4 turn until the spring releases and snaps the nut ring against the trolley.

This sets the spring to optimum belt tension.

Nut Ring Slot

Square End

You have now ﬁ nished assembling your garage door opener. Please read the following warnings before proceeding to the installation section.

Square End

BEFORE

(2.5 cm)

Trolley

Nut RingNut Ring

AFTER RELEASE

1-1/4"

(3.18 cm)

INSTALLATION

IMPORTANT INSTALLATION INSTRUCTIONS

To reduce the risk of SEVERE INJURY or DEATH:

1. READ AND FOLLOW ALL INSTALLATION WARNINGS AND INSTRUCTIONS.

2. Install garage door opener ONLY on properly balanced and lubricated garage door. An improperly balanced door may NOT reverse when required and could result in SEVERE INJURY or DEATH.

3. ALL repairs to cables, spring assemblies and other hardware MUST be made by a trained door systems technician BEFORE installing opener.

4. Disable ALL locks and remove ALL ropes connected to garage door BEFORE installing opener to avoid entanglement.

5. Install garage door opener 7 feet (2.13 m) or more above ﬂ oor.

6. Mount emergency release handle 6 feet (1.83 m) above ﬂ oor.

7. NEVER connect garage door opener to power source until instructed to do so.

8. NEVER wear watches, rings or loose clothing while installing or servicing opener. They could be caught in garage door or opener mechanisms.

9. Install wall-mounted garage door control:

• within sight of the garage door.

• out of reach of children at minimum height of

5 feet (1.5 m).

• away from ALL moving parts of the door.

10. Place entrapment warning label on wall next to garage door control.

11. Place manual release/safety reverse test label in plain view on inside of garage door.

12. Upon completion of installation, test safety reversal system. Door MUST reverse on contact with a 1-1/2" (3.8 cm) high object (or a 2x4 laid ﬂ at) on the ﬂ oor.

INSTALLATION STEP 1

Determine the Header Bracket Location

To prevent possible SERIOUS INJURY or DEATH:

• Header bracket MUST be RIGIDLY fastened to structural support on header wall or ceiling, otherwise garage door might NOT reverse when required. DO NOT install header bracket over drywall.

• Concrete anchors MUST be used if mounting header bracket or 2x4 into masonry.

• NEVER try to loosen, move or adjust garage door, springs, cables, pulleys, brackets, or their hardware, ALL of which are under EXTREME tension.

• ALWAYS call a trained door systems technician if garage door binds, sticks, or is out of balance. An unbalanced garage door might NOT reverse when required.

Installation procedures vary according to garage door types. Follow the instructions which apply to your door.

1. Close the door and mark the inside vertical centerline of the garage door.

2. Extend the line onto the header wall above the door.

You can fasten the header bracket within 4 feet

(1.22 m) of the left or right of the door center only if a torsion spring or center bearing plate is in the way; or you can attach it to the ceiling (see page 13) when clearance is minimal. (It may be mounted on the wall upside down if necessary, to gain approximately 1/2" (1 cm).)

If you need to install the header bracket on a 2x4

(on wall or ceiling), use lag screws (not provided) to securely fasten the 2x4 to structural supports as shown here and on page 13.

3. Open your door to the highest point of travel as shown. Draw an inter secting horizontal line on the header wall above the high point:

• 2" (5 cm) above the high point for sectional door

and one-piece door with track.

• 8" (20 cm) above the high point for one-piece door

without track.

This height will provide travel clearance for the top edge

of the door.

NOTE: If the total number of inches exceeds the height

available in your garage, use the maximum height possible, or refer to page 13 for ceiling installation.

Header Wall

Highest Point of Travel

Door

Sectional door with curved track

Door

Unﬁ nished Ceiling

Vertical Centerline of Garage Door

Level (optional)

2" (5 cm)

Track

Header Wall

8" (20 cm)

2x4

Header Wall

Door

One-piece door with horizontal track

Header Wall

Door

OPTIONAL CEILING MOUNT FOR HEADER BRACKET

Structural Supports

2" (5 cm)

Track

Highest Point of Travel

8" (20 cm)

Highest Point of Travel

Jamb Hardware

One-piece door without track: jamb hardware

Highest Point of Travel

Pivot

One-piece door without track: pivot hardware

+ 28 hidden pages

Chamberlain WD822KD User Manual

Model WD822KD 1/2 HP

TABLE OF CONTENTS

INTRODUCTION

Safety Symbol and Signal Word Review

Preparing your garage door

Tools needed

Planning

ONE-PIECE DOOR INSTALLATIONS

Carton Inventory

Hardware Inventory

Assemble the Rail & Install the Trolley

Fasten the Rail to the Motor Unit

Install the Idler Pulley

Install the Belt and Attach the Belt Cap Retainer

Set the Tension

INSTALLATION

Determine the Header Bracket Location