CDI Torque SPLIT BEAM CLICK TORQUE WRENCH User Manual
This torque wrench as calibrated at the factory, is
certified to meet the current ASME specification.
Additionally, all wrenches are calibrated on a torque
standard traceable to the National Institute of
Standards and Technology (N.I.S.T.).
CONvERsION TAbLE
To Convert Multiply
From To By
in. oz. in. lb. 0.06250
FOR YOUR PERMANENT FILECERTIFICATION
WRENCH MODEL NUMBER:
WRENCH SERIAL NUMBER:
For Warranty Claims, Contact CDI Torque Products
at (626) 965-0668.
OPERATION MANUAL
sPLIT bEAM CLICk
TORQUE WRENCH
in. lb. in. oz. 16
in. lb. ft. lb. 0.08333
in. lb. cmkg 1.15212
in. lb. mkg 0.01152
in. lb. Nm 0.11298
in. lb. dNm 1.12984
ft. lb. in. lb. 12
ft. lb. mkg 0.13825
ft. lb. Nm 1.35581
dNm in. lb. 0.88507
dNm Nm 0.1
Nm dNm 10
Nm cmkg 10.1971
Nm mkg 0.10197
Nm in. lb. 8.85074
Nm ft. lb. 0.73756
cmkg in. lb. 0.86796
LIMITED WARRANTY
The CDI Split Beam Click Torque Wrench is backed
by a one year warranty. This warranty covers
manufacturer defects and workmanship. The
warranty excludes misuse, abuse and normal
wear and tear. Exclusion is not allowed in some
states and may not apply. This warranty gives
you specific legal rights, and you may have other
rights, which vary from state to state.
IMPORTANT ENVIRONMENTAL NOTES:
1. This equipment may contain hazardous materials which can be
harmful to the environment.
2. Do not dispose of this equipment as municipal waste. Return it
to the distributor or a designated collection center.
Thank you for caring about our environment!
cmkg Nm 0.09806
mkg in. lb. 86.7961
mkg ft. lb. 7.23301
mkg Nm 9.80665
19220 SAN JOSE AVENUE • CITY OF INDUSTRY, CA 91748 • USA
(626) 965-0668
Find other ne torque products at WWW.CDITORQUE.COM
Form 20-301-CDI
6/2010 Rev. N/C
sAFETY MEssAGEs
WARNING
Read operation manual completely
before using torque instrument and
store for future reference.
ADJUsTMENTs OF
TORQUE sETTINGs
SET KNOB
APPLY FORCE
SCALE
WINDOW
Wear safety goggles-both user and
bystanders
• An out of calibration torque wrench
can cause part or tool breakage
• Periodic re-calibration is necessary to
maintain accuracy
• Do not exceed rated torque as
overtorquing can cause wrench or part
failure
• Do not use torque instrument to break
fasteners loose
• Do not use cheater extension on the
handle to apply torque
• Broken or slipping tools can cause
injury.
CAUTION - RATCHET HEAD
Ratchet mechanism may slip or break
if dirty, mismatched or worn parts are
used, or direction lever is not fully
engaged. Ratchets that slip or break
can cause injury.
MAINTENANCE / sERvICE
1. The torque wrench’s internal mechanism is
permanently lubricated during assembly. Do not
attempt to lubricate the internal mechanism.
SET
MARK
LOCK
LEVER
1. Pull back on the lock lever to unlock the set knob.
2. With the set knob turned to the lowest value, turn
the knob clockwise to the desired value indicated at
the set mark. If the value is exceeded, back off and
approach the proper seting from the low side.
3. Close the lock lever to lock the set knob at the
torque setting.
4. To torque fastener, keep hand centered on the
handle, apply a slow steady force in the clockwise
direction until a click/impulse is heard or felt. Stop
pulling and allow the wrench to reset.
RELEASE
FORCE TO RESET
UsE OF ExTENsIONs
AND ADAPTERs
When using an extension or adapter (increasing the
effective length of the torque wrench) the output
torque value will change. To calculate the new torque
output of the wrench use the following formula:
TA x L
TW =
TA = Torque exerted @ end of adapter
L = Distance between square drive and hand position
TW = Wrench scale reading
A = Length of adapter or extension
TA TW
A
L + A
L
2. Clean torque wrench by wiping. Do not immerse.
3. Store torque wrench in protective tube at its lowest
torque setting. Do not force handle below lowest
setting.
A number of variables can affect torque accuracy.
These include the length of an adapter or extension,
length of the wrench and variations in hand position
on the wrench will affect the accuracy of the above
calculation.
Loading...