CAT INV1250, INV2000, INV2250 User Manual
517–9204-04
Owner's Manual
INV1250, INV2000, INV2250
Portable Generators
2
Important Safety Information
Most accidents that involve product operation, maintenance and repair are caused by failure to observe
basic safety rules or precautions. An accident can often be avoided by recognizing potentially hazardous
situations before an accident occurs. A person must be alert to potential hazards, including human factors
that can affect safety. This person should also have the necessary training, skills and tools to perform
these functions properly.
Safety precautions and warnings are provided in this manual and on the product. If these hazard
warnings are not heeded, bodily injury or death could occur to you or to other persons. The hazards are
identified by the “Safety Alert Symbol” and followed by a “Signal Word” such as “DANGER”,
“WARNING” or “CAUTION”.
Caterpillar cannot anticipate every possible circumstance that might involve a potential hazard. The
warnings in this publication and on the product are, therefore, not all inclusive. You must not use this
product in any manner different from that considered by this manual without first satisfying yourself that
you have considered all safety rules and precautions applicable to the operation of the product in the
location of use, including site-specific rules and precautions applicable to the worksite. If a tool,
procedure, work method or operating technique that is not specifically recommended by Caterpillar is
used, you must satisfy yourself that it is safe for you and for others. You should also ensure that you are
authorized to perform this work, and that the product will not be damaged or become unsafe by the
operation, lubrication, maintenance or repair procedures that you intend to use.
The information, specifications, and illustrations in this publication are on the basis of information that was
available at the time that the publication was written. The specifications, torques, pressures,
measurements, adjustments, illustrations, and other items can change at any time. These changes can
affect the service that is given to the product. Obtain the complete and most current information before
you start any job.
In the United States, the maintenance, replacement, or repair of the emission control devices and systems
may be performed by any repair establishment or individual of the owner's choosing.
This manual contains safety, operation, and maintenance information. This manual should be stored near
the product. Read, study and keep it with the literature and product information.
Consumer Arbitration Clause
The Limited Warranty included in this User Guide contains important legal terms including, but not limited
to, a Consumer Arbitration Clause calling for mandatory individual arbitration and waiving the ability to
bring a case as a class action. Please review this carefully.
California Proposition 65 Warning
3
Table of Contents
Consumer Arbitration Clause .................................................................................................................... 2
California Proposition 65 Warning ............................................................................................................... 2
SAFETY MESSAGES ................................................................................................................................... 5
Additional Messages ................................................................................................................................. 6
Special Requirements ............................................................................................................................... 6
COMPONENT IDENTIFICATION (INV2000 / INV2250) ............................................................................... 7
COMPONENT IDENTIFICATION (INV1250) ................................................................................................ 8
Engine Type & Serial Number ................................................................................................................... 9
FIRST USE INSTRUCTIONS ....................................................................................................................... 9
Oil .............................................................................................................................................................. 9
Fuel ........................................................................................................................................................... 9
Walk-Around Inspection ............................................................................................................................ 9
CONTROLS ................................................................................................................................................ 10
Display LEDs ........................................................................................................................................... 10
Generator Switch .................................................................................................................................... 10
CO DEFENSETM & Shut Off System (If equipped) ................................................................................ 10
Parallel Receptacles ............................................................................................................................... 11
Engine Smart Control Switch .................................................................................................................. 11
AC/DC Circuit Breakers .......................................................................................................................... 11
USB Receptacles .................................................................................................................................... 11
Low Oil Level Shutdown .......................................................................................................................... 11
GENERATOR OPERATION........................................................................................................................ 12
Optimal Generator Operating Conditions ................................................................................................ 12
Connection to Household Power Supply ................................................................................................. 12
Generator Grounding .............................................................................................................................. 12
AC Usage ................................................................................................................................................ 12
High Altitude Kits ..................................................................................................................................... 12
BEFORE STARTING ENGINE ................................................................................................................... 13
Engine Oil ................................................................................................................................................ 13
Fuel Level - Check .................................................................................................................................. 13
STARTING THE ENGINE ........................................................................................................................... 13
Recoil Start .............................................................................................................................................. 13
STOPPING THE ENGINE ........................................................................................................................... 13
MAINTENANCE .......................................................................................................................................... 14
Air Filter – Check ..................................................................................................................................... 14
Cylinder Head - Clean ............................................................................................................................. 14
Engine Oil Level – Check ........................................................................................................................ 15
Engine Oil – Change ................................................................................................................................ 15
Engine Valve Lash – Inspect/Adjust ....................................................................................................... 15
Fuel Line – Replace ................................................................................................................................ 16
4
Fuel Tank Cap and Strainer – Clean ...................................................................................................... 16
Generator - Inspect ................................................................................................................................. 16
Spark Arrestor - Inspect/Clean/Replace.................................................................................................. 16
Spark Plug – Inspect/Adjust/Replace ...................................................................................................... 17
Walk-Around Inspection .......................................................................................................................... 17
STORAGE ................................................................................................................................................... 18
Storage for 1 to 3 months ........................................................................................................................ 18
Storage for more than 3 months ............................................................................................................. 18
TROUBLESHOOTING ................................................................................................................................ 19
SPECIFICATIONS ...................................................................................................................................... 20
COMBINED EXHAUST AND EVAPORATIVE EMISSIONS CONTROLS WARRANTY STATEMENT ..... 21
Your Warranty Rights and Obligations .................................................................................................... 21
Manufacturer’s Warranty Coverage ........................................................................................................ 21
Owner’s Warranty Responsibilities ......................................................................................................... 21
Defects Warranty Requirements: ............................................................................................................ 21
WARRANTY ................................................................................................................................................ 23
CONSUMER ARBITRATION CLAUSE: MANDATORY BINDING INDIVIDUAL ARBITRATION
INSTEAD OF COURT; CLASS ACTION WAIVER ................................................................................. 23
5
SAFETY MESSAGES
There may be several specific safety messages
on your generator. Please become familiar with
all safety messages.
Ensure that all of the safety messages are legible.
Clean the safety messages or replace the safety
messages if the words cannot be read or if the
illustrations are not visible. Use a cloth, water, and
soap to clean the safety messages. Do not use
solvents, gasoline, or other harsh chemicals.
Solvents, gasoline, or harsh chemicals could
loosen the adhesive that secures the safety
messages.
Replace any safety message that is damaged or
missing. If a safety message is attached to a part
of the generator that is replaced, install a new
safety message on the replacement part.
Read the Manual
Do not operate or work on this generator unless
you have read and understand the instructions
and warnings in the Owner’s Manual. Failure to
follow the instructions or heed the warnings could
result in injury or death. Proper care is your
responsibility.
Hot Surface / Do Not Touch /
Flammable Material
Hot parts or hot components can cause burns or
personal injury. Do not allow hot parts or
components to contact your skin. Use protective
clothing or protective equipment to protect your
skin. Hot exhaust presents a potential fire hazard.
Be sure that nothing flammable is within 1.5
meters of the exhaust.
Carbon Monoxide
Operating a generator indoors can kill you in
minutes. Generator exhaust contains carbon
monoxide. Carbon monoxide is a poison that you
cannot see or smell. Never operate a generator
inside a home or garage, even if doors and
windows are open. Only operate a generator
outdoors and away from windows, doors, and
vents. Always direct engine exhaust away from
occupied structures. If anyone experiences
dizziness, headaches, nausea, or tiredness get to
fresh air immediately and seek medical attention.
Ventilate the area thoroughly before occupying
again.
The carbon monoxide shutoff system (if
equipped) is not a substitute for safe generator
operation. Do Not adjust or modify the carbon
monoxide shutoff system. Failure to follow
instructions can cause the system to malfunction
which can result in hazardous conditions.
DANGER
PELIGRO
Utiliser un générateur à
l’intérieur PEUT VOUS TUER EN
QUELQUES MINUTES. Les gaz
d’échappement du générateur
contiennent du monoxyde de
carbone. C’est un gaz toxique
invisible et inodore.
NE JAMAIS utiliser à l’intérieur
d’une maison ou d’un garage,
MÊME SI les portes et les
fenêtres sont ouvertes.
Utiliser UNIQUEMENT à
l’EXTÉRIEUR et loin des
fenêtres, portes et ventilations.
Si usa un generador en
interiores, MORIRA EN POCOS
MINUTOS. El escape del
generador contiene monóxido
de carbono. Es un veneno que
no tiene olor ni se puede ver.
NUNCA lo use dentro de una
casa o garaje. AUN si las
puertas y vantanas están
abiertas.
Sólo úselo en EXTERIORES
y lejos de ventanas, puertas y
ductos de ventilación.
6
Electrocution
Shock/Electrocution Hazard: Do not operate this
equipment or work on this equipment unless you
have read and understand the instructions and
warnings in the Owner’s Manual. Failure to
follow the instructions or heed the warnings will
result in serious injury or death.
Operation of this equipment may create sparks
that can start fires around dry vegetation. A spark
arrestor may be required. The operator should
contact local fire agencies for laws or regulations
relating to fire prevention requirements.
Electrical backfeed into a utility’s distribution system
can cause property damage, severe injury, or death.
Electrical backfeed warning. Do not connect
generator to a building’s electrical system unless
using an isolation (transfer) switch installed by a
certified, licensed electrician. CA H&S Code
119075 & 119080.
Additional Messages
Do not operate in wet
conditions
No smoking, no exposed
flames, no sparks.
Maintain a minimum distance
of 5 feet (1.5 meters) from
other objects.
Ensure that the unit is
properly grounded.
Earth ground connection
Special Requirements
Electrical equipment, including lines and plug
connections should be covered and protected
from moisture.
In any generator set installation, the frame of the
generator must be connected to an earth
ground. A ground terminal is provided.
The INV1250/INV2000/INV2250 has a
permanent neutral conductor bonded to the
frame.
For 120VAC, use extension cords rated for 125V
at 20A or greater. Use the shortest extension
cord that meets these requirements.
•
Wear a hard hat, protective glasses, and
other protective equipment, as required.
•
When work is performed around an engine
that is operating, wear protective devices for
ears in order to help prevent damage to
hearing.
•
Do not wear loose clothing or jewelry that can
snag on controls or on other parts of the
engine.
•
Ensure that all protective guards and all
covers are secured in place on the engine.
•
Never put maintenance fluids into glass
containers. Glass containers can break.
•
Use all cleaning solutions with care.
The circuit breakers should match the generator
specifications. If the circuit breakers require
replacement, they must be replaced with a
circuit breaker of the same rating and
performance characteristics.
7
COMPONENT IDENTIFICATION (INV2000 / INV2250)
1) Vacuum Relief Valve
2) Fuel Cap
3) Panel Light
4) Recoil Starter
5) Fuel Gauge
6) Spark Plug Cover
7) Spark Arrestor
8) Oil Gauge / Oil Fill / Oil Drain*
9) Air Filter Assembly*
10) Generator Switch
11) Engine Smart Control (ESC) Switch
12) Display LEDs
13) Receptacle – 120 VAC double GFCI
14) AC Circuit Breaker
15) Ground Terminal
16) Parallel Receptacles
17) Receptacle – USB double
18) Receptacle – 12VDC 8.3A
19) DC Circuit Breaker
20) CO DEFENSETM (If equipped)
*behind service access door
1
2
4
3
5
6
7
8
9
Panel without CO DEFENSE
TM
Panel with CO DEFENSE
TM
8
COMPONENT IDENTIFICATION (INV1250)
1) Vacuum Relief Valve
2) Fuel Cap
3) Panel Light
4) Oil Gauge / Oil Fill / Oil Drain*
5) Air Filter Assembly*
6) Fuel Gauge
7) Spark Plug Cover
8) Spark Arrestor
9) Recoil Starter
10) Generator Switch
11) Receptacle – USB double
12) Display LEDs
13) Parallel Receptacles
14) Engine Smart Control (ESC) Switch
15) AC Circuit Breaker
16) Receptacle – 120 VAC
17) CO DEFENSETM (If equipped)
18) Ground Terminal
*behind service access door
1
2
4
3
6 7 8
9
Panel without CO DEFENSE
TM
Panel with CO DEFENSE
TM
11
12
13
14
15
16
18
10
17
5
9
Engine Type & Serial Number
INV1250
INV2000 / INV2250
Cat® portable generators are identified with model numbers, serial numbers, and with performance
specification numbers. The model number and performance specifications are located on the ratings
plate (2). The serial number is located on the serial number plate (1).
FIRST USE INSTRUCTIONS
Oil
Follow the Engine Oil Level-Check procedure to add the proper amount of oil for the unit as described in
the Specifications chart.
Note: The generator is shipped with no oil in the engine, add the proper amount before first use.
Fuel
Follow the Fuel Level – Check procedure to add the proper amount of fuel for the unit as described in the
Specifications chart.
Walk-Around Inspection
Perform the Walk-Around Inspection before each use as described later in this manual.
1
2
2
10
CONTROLS
Display LEDs
This generator is equipped with 3 Display LEDs
that indicate Low Oil (1), Overload (2), and
Output Power (3). The low oil indicator will
illuminate red when there is an insufficient
amount of oil in the crankcase. The overload
indicator will illuminate red when there is a short
circuit in a connected load, or the generator is
overloaded. The output power indicator will
illuminate green when the generator is in normal
operation.
Generator Switch
Turn the generator switch to the choke position
when starting the engine. Refer to Starting the
Engine – Recoil Start. Turn the generator switch
to the on position “I” once it has been started. To
turn off the generator, turn the generator switch
to the off “0” position.
CO DEFENSETM & Shut Off System
(If equipped)
The (carbon monoxide) CO DEFENSETM system
monitors the accumulation of CO gas while the
generator is running and will shut off the engine if
the levels become dangerously high. The CO
DEFENSETM on this generator is not a substitute for
an indoor CO alarm.
Whenever the CO DEFENSETM has shut off the
engine there will be a light on the control panel that
indicates the reason. Read the CO Action Label
(shown above) for the next steps to take.
If the CO DEFENSETM light is flashing “red” you
must leave the area immediately and relocate to an
open outdoor area. Ventilate the area thoroughly
before occupying again. Ensure the generator is
located in an open outdoor area with the exhaust
pointed away from occupied structures. If anyone
experiences dizziness, headaches, nausea, or
tiredness get to fresh air immediately and seek
medical attention.
If the CO DEFENSETM light is a constant “orange”
then a system fault has occurred, or it is indicating
that it has reached the end of its life. This fault can
only be diagnosed and repaired by an Authorized
Service Provider.
The CO DEFENSETM monitors the accumulation of
CO gas from all sources in the area around the
generator. If the CO DEFENSETM light is flashing
“red” this is not an error and safety measures must
be taken immediately.
Note: Tampering with the CO DEFENSETM could result
in hazardous conditions and must be avoided.
Note: The generator must not be operated in ambient
temperatures greater than 131oF (55oC) as this can
damage the CO DEFENSETM.
11
Parallel Receptacles
Two parallel ready generators can be connected
together to increase the total power available to
a load by using the parallel receptacles. The
system seamlessly matches frequency and
automatically distributes the load to each
generator so one is not overloaded. Follow the
parallel kit (sold separately) instructions for
connection and use of a parallel kit.
Engine Smart Control Switch
This generator is equipped with an engine smart
control switch. When in the on position “I” the
engine will vary speed to match the required
power output to conserve fuel, and reduce wear
and noise.
Note: If loads requiring intermittent power, or
multiple large loads are connected, turn the
electronic speed control switch off “O” to avoid
possible engine stall. To avoid extended warmup time, keep the electronic speed control off
until normal operating temperatures have been
reached.
AC/DC Circuit Breakers
The generator comes equipped with circuit
breakers that protect the unit and the load from
short circuit or overload conditions. If the circuit
breaker opens, determine why the circuit breaker
tripped before closing the circuit breaker.
USB Receptacles
The generator comes equipped with a double
USB receptacle. The top is a 5V 1A USB port and
the bottom is a 5V 2.1A USB port.
Low Oil Level Shutdown
The generator is equipped with a low oil level
shutdown that is designed to protect the engine
from damage caused by an insufficient amount
of oil in the crankcase. When the oil level in the
crankcase falls below the safe operating limit,
the low oil level light will illuminate and the
engine will automatically shutdown.
120 VAC, 20 Amp, Single or Duplex
The 120 VAC single or duplex receptacle is
protected against overload by a 20 Amp push to
reset circuit breaker. . It also provides protection
via a Ground Fault Circuit Interruptor (GFCI) with
press to Test and Reset buttons (INV2000/
INV2250). Use the receptacle to power a NEMA
5-20, 120 VAC, single phase, 60 Hz electrical
load requiring 20 Amps of current.
Use only high quality, well insulated, 3-wire
grounded cords rated for 125 V at 20 Amps (or
greater). Keep extension cords as short as
possible (less than 15 feet) to prevent voltage
drop and overheating of wires.
12
GENERATOR OPERATION
Optimal Generator Operating
Conditions
• Temperature: 23oF to 104 oF
(-5oC to 40oC)
• Humidity below 95%
• Height above sea level: < 3000 feet (900
m). If the height of the operating area is over
900 m high, output power will be reduced.
Standard operating conditions are 77oF (25oC)
and 40% humidity. Generator power may be
reduced due to different ambient conditions and
other factors such as fuel quality.
Connection to Household Power
Supply
This generator must be installed in accordance
with all applicable local laws and electrical
codes. The generator must be isolated from the
utility and the connection must be verified by a
qualified electrician.
Generator Grounding
The National Electrical Code requires generators
to be grounded to an approved earth ground.
Correct grounding for the generator is necessary
for optimum engine performance and reduces
the risk of electric shock. Use the ground
terminal (1) to properly ground the generator.
Before using the ground terminal, consult a
qualified electrician, electrical inspector, or local
authority having jurisdiction for local codes or
ordinances that apply for the intended use of the
generator.
AC Usage
Do NOT overload the generator. Exceeding the
rated power of the generator can damage the
generator and the electrical devices connected
to it.
Motor-driven devices require a large starting
current. Make sure that the total power
requirement of these types of loads does not
exceed the rated power of the generator.
When the generator is used to power multiple
loads or electric appliances, start by connecting
the appliance with the highest starting power
requirements, followed by the second highest
and ending with the lowest.
High Altitude Kits
At higher altitudes, the standard air-fuel mixture
is too rich and will cause decreased
performance and increased fuel consumption. A
rich mixture will also foul the spark plug and
make starting difficult. Operation at higher
altitudes for extended periods of time may
increase emissions.
Proper operation can be ensured by installing an
altitude kit when required. High altitude kits
should be installed by a qualified technician.
Contact an authorized service provider if the
portable generator will be operated at altitudes
greater than 3000 feet (0.9 km) above sea level.
Note: At elevations greater than 8000 feet
above sea level, the engine may experience
decreased performance even with the high
altitude kit installed.
13
BEFORE STARTING ENGINE
Engine Oil
Check the oil level before each use. Refer to the
Engine Oil Level - Check procedure in this
manual.
Fuel Level - Check
1. Check the fuel level gauge (2).
2. If the fuel level is low, remove fuel cap
(1).
3. Check the strainer. If the strainer is
dirty, clean the strainer. Refer to Fuel
Tank Cap and Strainer – Clean for
instructions.
4. Add fuel. The use of a fuel stabilizer is
highly recommended as the unit may
sit for long periods of time before
needed.
5. Install the fuel cap after fueling.
To avoid personal injury always use caution
when you are adding fuel:
• Fuel the generator in a well-ventilated
area.
• Always stop the engine before fueling.
• Always fill with the generator on a level
surface.
• Allow the engine to cool before fueling.
• Do not smoke while you are fueling the
generator.
• Do not fuel the generator near open
flames or sparks.
• Do not fill the fuel tank above the full line.
• Avoid repeated or prolonged contact with
skin.
• Avoid prolonged breathing of fuel vapor.
To avoid damaging the generator:
• Use unleaded gasoline with an octane
rating greater than or equal to 86.
• Do not mix oil with the gasoline.
• Do not use gasoline with greater than
10% ethanol content.
• Do not use old gasoline.
• Avoid getting dirt or water into the fuel
tank.
STARTING THE ENGINE
Recoil Start
1. Isolate the generator from the utility.
2. Unplug any electrical devices from the
receptacles.
3. Turn the Engine Smart Control Switch
to the off “0” position.
4. Open the vacuum relief valve on top of
the fuel cap by rotating clockwise to the
on “I” position.
5. Turn the generator switch to the choke
position.
6. Slowly pull the starter handle until
resistance is felt, then quickly pull the
starter handle the rest of the way. If the
engine does not start, repeat step 6
until the engine does start.
7. After the engine has started, turn the
generator switch to the on “I” position.
STOPPING THE ENGINE
1. Disconnect the generator / unplug all
electrical devices.
2. Turn the generator switch to the off “0”
position.
3. Close the vacuum relief valve on top of
the fuel cap by rotating counterclockwise to the off “0” position.
NOTE: To stop the engine in an emergency, turn
the generator switch to the off “0” position.
2
1
14
MAINTENANCE
Ensure that all safety information, warnings, and
instructions are read and understood before any
maintenance procedures are performed.
Use service hours or calendar time, WHICH
EVER OCCURS FIRST, to determine the
correct maintenance intervals.
Stop the engine before servicing. Put the
generator on a level surface and remove the
spark plug cap to prevent the engine from
starting. Do not operate the engine in an
unventilated room or other enclosed area.
When Required:
Fuel Tank Cap and Strainer – Clean
Every Use:
Engine Oil Level – Check
Walk-Around Inspection
First 20 Service Hours or 1 Month:
Engine Oil – Change
Every Month:
Generator – Inspect
Every 50 Service Hours or 3 Months:
Spark Arrester – Inspect/Clean/Replace
Every 100 Service Hours or 6 Months:
Engine Oil – Change
Air Filter – Check
Spark Plug – Inspect/Adjust/Replace
Every 300 Service Hours or 1 Year:
Cylinder Head – Clean
Engine Valve Lash – Check
Every 2 Years:
Fuel Line – Check/Replace if necessary
NOTE: Only use Caterpillar genuine parts.
Air Filter – Check
A dirty air filter will restrict air flow into the
carburetor, will cause poor fuel economy, and
may damage the engine. To keep the generator
in good operating condition, service the air filter
regularly. Service more frequently when
operating the generator in extremely dusty areas.
Note: Never operate the generator without the
air filter in place. Operating the generator without
the air filter in place will result in rapid engine
wear.
Open the left service door (1). Remove the air
filter cover bolt (2) and remove the air filter cover
(3) by lifting out the service door opening. Make
sure that the air filter is clean and not damaged.
If the air filter is dirty, wash the filter. If the air
filter is damaged, replace the air filter.
Use a nonflammable solvent or a mixture of
household detergent and warm water to wash
the filter. Rinse the filter thoroughly to remove all
of the cleaning solution. After the filter has dried,
pour a small amount of engine oil into the filter
and squeeze to distribute the oil throughout.
Remove excess oil and replace the filter.
Note: Do not wring out the filter. Wringing out the
filter may damage the filter.
Use a damp rag to wipe dirt from the case and
cover. Install the filter into the housing. Place the
air filter cover over the filter and reinstall the air
filter cover bolt. Reinstall the service door.
Cylinder Head - Clean
Only qualified service personnel should perform
this maintenance procedure. Contact your local
service center to schedule this maintenance.
1
2
3
1
2
3
INV1250
INV2000 / INV2250
15
Engine Oil Level – Check
Always check the engine oil with the generator
on a level surface and with the engine stopped.
1.
Open the service door (1). Remove the
oil level gauge (2) and wipe clean.
2.
Check the oil level by re-inserting the oil
level gauge (do not screw in tight).
3.
If the oil level is low (4), add the
recommended engine oil, using the
funnel supplied, until the oil level reaches
the upper mark (3) on the oil level
gauge. Use the chart below to
determine which viscosity oil to use.
4.
After adding oil, install and tighten the oil
level gauge (2), and close the service
door (1).
Note: Non-detergent and 2-stroke engine oils will
damage the engine and must not be used.
Engine Oil – Change
1. Operate the engine until it reaches
normal operating temperature. Stop the
engine and use a suitable container to
collect the used oil.
2. Close the vacuum relief valve on top of
the fuel cap by rotating counterclockwise to the off “0” position.
3. Open the service door (1). Remove the
oil level gauge (2), wipe clean, and set
aside.
4. Attach the oil funnel supplied, and tilt
the generator so the used oil flows
from the engine into the container and
fully tilt the generator until the
crankcase is empty. Wipe the funnel
clean.
5. Refill the oil, using the funnel supplied,
and check the oil level. Refer to Engine
Oil Level – Check.
6. Install and tighten the oil level gauge.
Close the service door (1).
7. Dispose of the used oil properly.
8. Start the engine for a brief period and
check for leaks.
9. Stop the engine and check the oil level.
Refer to Engine Oil Level – Check.
Engine Valve Lash – Inspect/Adjust
Only qualified service personnel should perform
this maintenance procedure. Contact your local
service center to schedule this maintenance.
Recommended Lubricant Viscosities for
Ambient Temperature
Oil Viscosities
oC o
F
Min
Max
Min
Max
SAE 0W-40
-40
40
-40
104
SAE 5W-40
-30
50
-22
122
SAE 10W-30
-18
40 0 104
SAE 15W-40
-10
50
14
122
2
3
4
2
1 2 1
16
Fuel Line – Replace
Only qualified service personnel should perform
this maintenance procedure. Contact your local
service center to schedule this maintenance.
Fuel Tank Cap and Strainer – Clean
Wipe off the fuel cap (1) and surrounding area
before removing the fuel cap. Wiping off the fuel
cap and surrounding area before removing the
fuel cap helps to reduce the amount of
contaminants allowed into the fuel system.
If there is a build-up of debris in the fuel strainer
(2), remove the strainer and rinse out the
strainer. Allow the strainer to dry before
installing the strainer.
Generator - Inspect
Once a month start the engine and run the
engine until it reaches normal operating
temperature (about 10 minutes). Plug in a
corded device and turn on the device to ensure
that the generator is providing power. Once you
have verified that the generator is providing
power, turn off the device and unplug it. Then
turn the generator off.
Spark Arrestor Inspect/Clean/Replace
This unit has a spark arrestor fitted to the
exhaust outlet of the muffler. The spark arrestor
should be cleaned with a soft wire brush after
every 50 hours or 3 months of use. The spark
arrestor should be replaced after every 100
hours of operation or if it becomes damaged.
Hot Surface
Hot parts or hot components can cause burns or
personal injury. Do not allow hot parts or
components to contact your skin. Use protective
clothing or protective equipment to protect your
skin.
DO NOT perform this maintenance procedure
until the muffler has cooled.
Remove screws (1). Remove spark arrestor (2)
Check the spark arrestor. Carefully clean the
spark arrestor with a soft wire brush. If the spark
arrestor is damaged, replace the spark arrestor.
To install the spark arrestor, align the mounting
holes in the spark arrestor with the mounting
holes on the muffler. Insert screws (1) and
tighten securely.
2
1
1
2
17
Spark Plug – Inspect/Adjust/Replace
Refer to the Specifications section of this
manual to determine the proper spark plug part
number and spark plug gap for your product.
INV2000/ INV2250
INV1250
1. DO NOT perform this maintenance
procedure with the engine running.
2. Turn the generator switch to the off “O”
position.
3. Remove the screws (5) to remove the
outer side panel by pushing up and out
to access the engine.
4. Remove the spark plug boot by lifting it
off the top of the spark plug and remove
the spark plug access cover (2) by
rotating and pulling out.
5. Use the plug wrench (4) or a spark plug
socket to remove the spark plug (3).
6. Visually check the spark plug to see if
it is damaged. If the insulator is
cracked, replace the spark plug. If the
electrode is damaged, replace the spark
plug.
7. Measure the plug gap (1) with a feeler
gauge. Adjust the gap as necessary by
carefully bending the side electrode.
Refer to Specifications for the correct
gap for your product.
8. Check the spark plug washer to ensure
proper working condition. If the washer
is damaged, replace the washer.
9. Install spark plug and tighten to 9 ± 2 lb
ft (12.5 ± 2 Nm). DO NOT overtighten
as this may damage the engine.
10. Re-attach the spark plug boot, spark
plug cover (2), and outer side panel.
Walk-Around Inspection
Before starting the engine perform a visual
inspection of the unit. Look for:
• Proper oil level
• Proper fuel level
• Good quality fuel
• Fluid leaks
• Loose clamps
• Loose bolts
• Cracked fuel line
• Loose or frayed wiring
• Built up debris
In addition, make sure that:
• The ground terminal is properly
connected
1
4
5
3
2
18
STORAGE
When a generator is in storage, air may
condense and moisture may appear on the
windings. In order to minimize condensation,
always store the generator in a dry area. Cover
the generator with a protective cover that
extends to the ground. The cover should remain
loose around the generator in order to allow
proper ventilation.
The generator must not be stored in ambient
temperatures greater than 131oF (55oC) as this
can damage the CO DEFENSETM (if equipped).
Wait until the generator has cooled before
covering it. NEVER operate the generator with
the cover installed. It could ignite and cause
damage.
Storage for 1 to 3 months
Remove any dirt, rust, grease, and oil from the
generator. DO NOT use a pressure washer to
clean the generator. Inspect the exterior. Make
any necessary repairs.
Add fuel stabilizer to the fuel tank to prevent the
gasoline from going bad. Start and run the
engine for 5 minutes to ensure that the fuel
stabilizer has been pulled in to the carburetor.
Shut off the engine and allow the engine to cool.
Turn the generator switch to the off “O” position.
Move the generator to the storage place.
Cover the generator.
Storage for more than 3 months
Remove any dirt, rust, grease, and oil from the
generator. DO NOT use a pressure washer to
clean the generator. Inspect the exterior. Make
any necessary repairs.
Gasoline is extremely flammable and is
explosive under certain conditions. Drain the fuel
in a well-ventilated area with the engine stopped
and cool. Never smoke or allow flames or sparks
in the area during this procedure.
Remove the fuel cap and carefully turn the
generator over to pour the gasoline into an
appropriate container. Reinstall the fuel cap and
start and run the engine until the engine stops,
to allow the fuel to drain from the fuel lines,
carburetor, and engine system.
Change the engine oil. Refer to Engine Oil –
Change.
Remove the spark plug and pour a small amount
of oil into the cylinder. Install the spark plug but
do not install the spark plug boot.
Turn the generator switch to the off “O” position.
Move the generator to the storage place.
Cover the generator.
19
TROUBLESHOOTING
Issue:
Possible Cause:
Solution:
Check:
Engine Will
Not Start
Generator switch in the off “0”
position
Turn the generator switch to the correct
position.
Start the engine.
Generator inclined
Move generator to a level position.
No fuel
Fill the fuel tank.
Bad or contaminated fuel
Check the fuel.
Not enough oil in the engine
Check the oil level. If low, add the
recommended oil.
Dirty air filter
Clean the air filter.
No spark
Replace the spark plug.
Oil in the combustion chamber
Remove spark plug, turn generator switch
to off “O” position, pull recoil starter four
times to remove oil from combustion
chamber.
If the engine still will not start:
Take the unit to an authorized service provider.
Engine
Runs
Rough (no
load)
Dirty air filter
Stop the engine and check the air filter.
Clean if needed.
Start the engine /
check if it runs
rough.
Generator inclined
Move generator to a level position.
If the engine still runs rough:
Take the unit to an authorized service provider.
Engine
Shuts
Down
Out of fuel
Check the fuel. Fill the tank if necessary.
Start the engine /
check if it shuts
down.
Not enough oil in the engine
Check the oil level. If low, add the
recommended oil.
Dirty air filter
Clean the air filter.
Shut off due to CO accumulation &
flashing red indicator
Follow all safety instructions on CO Action
Label
Generator overloaded
Unplug some of the devices.
Vacuum relief valve in off “O” position
Turn vacuum relief valve to on “I” position.
Shut off due to CO DEFENSETM system
fault & constant orange indicator
System fault or end of life indication. Take the unit to an
authorized service provider.
If the engine still shuts down:
Engine
Runs
Rough
(with load)
Dirty air filter
Stop the engine and check the air filter.
Clean if needed.
Start the engine /
check if it runs
rough.
Generator overloaded
Unplug some of the devices.
Defective device plugged in
Unplug defective device.
If the engine still runs rough:
Take the unit to an authorized service provider.
Engine
Runs, But
Generator
Does Not
Provide
Power
Generator overloaded, overload light is
on
Turn off and unplug all electrical devices,
shut down the engine, wait 10 minutes &
start the engine, connect fewer or lighter
electrical loads.
Start the engine /
check for power.
Bad connection
Stop the engine and check the
connections.
Defective power cord
Replace the cord.
Defective device plugged in
Unplug defective device.
If there is still no power:
Take the unit to an authorized service provider.
20
SPECIFICATIONS
INV1250
INV2000 / INV2250
Engine Type
Single Cylinder, 4-Stroke, Forced
Air Cooling
Single Cylinder, 4-Stroke,
Forced Air Cooling
Displacement (cc)
60
79.7
Ignition System
Electronic
Electronic
Spark Plug Gap
.024 - .032 inches (0.6 – 0.8mm)
.024 - .032 inches (0.6 – 0.8mm)
Fuel Volume
0.8 U.S. gallon (3L)
1.05 U.S. gallon (4L)
Fuel Consumption
(g/(kW·h)
≤ 450
≤ 450
100% load continuous
4.9
3.5
running time (hr)
50% load continuous
7.9
6
running time (hr)
Oil Capacity
0.33 quart (0.31L)
0.40 quart (0.38L)
Rated Output (DC)
N/A
12V 8.3A
Rated Frequency (Hz)
60
60
Rated Voltage (V)
120
120
Rated Output Power (kW)
1.0
1.8
Surge Output Power (kW)
1.25
2.25
Phase
Single
Single
Total Harmonic Distortion
< 3%
< 3%
21
COMBINED EXHAUST AND
EVAPORATIVE EMISSIONS
CONTROLS WARRANTY
STATEMENT
Your Warranty Rights and
Obligations
The California Air Resources Board (CARB), the
United States Environmental Protection Agency
(EPA), and Caterpillar Inc. are pleased to
explain the exhaust and evaporative emissions
control system warranty on your 2020 model
year small off-road engine/equipment. In the
United States and California, new equipment
that use small off-road engines must be
designed, built, and equipped to meet stringent
emissions standards. Caterpillar must warrant
the emission control system on your small offroad engine/equipment for the periods of time
listed below provided there has been no abuse,
neglect, or improper maintenance of your small
off-road engine/equipment leading to the failure
of the emissions control system.
Your emissions control system may include
parts such as the carburetor or fuel injection
system, the ignition system, catalytic converter,
fuel tanks, fuel lines (for liquid fuel and fuel
vapors), fuel caps, valves, canisters, filters,
clamps, and other associated components. Also
included may be hoses, belts, connectors, and
other emission-related assemblies.
Where a warrantable condition exists, Caterpillar
will repair your small off-road engine/equipment
at no cost to you including diagnosis, parts, and
labor.
Manufacturer’s Warranty Coverage
This emissions control system is warranted for
three years. If any emission-related part on your
small off-road engine/equipment is defective, the
part will be repaired or replaced by Caterpillar.
Owner’s Warranty Responsibilities
As the small off-road engine/equipment owner,
you are responsible for the performance of the
required maintenance listed in your owner's
manual. Caterpillar recommends that you retain
all receipts covering maintenance on your small
off-road engine/equipment, but Caterpillar
cannot deny warranty coverage solely for the
lack of receipts or for your failure to ensure the
performance of all scheduled maintenance.
As the small off-road engine/equipment owner,
you should however be aware that Caterpillar
may deny you warranty coverage if your small
off-road engine/equipment or a part has failed
due to abuse, neglect, improper maintenance or
unapproved modifications.
You are responsible for presenting your small
off-road engine/equipment to a Caterpillar
distribution center or service center as soon as a
problem exists. The warranty repairs shall be
completed in a reasonable amount of time, not
to exceed 30 days.
If you have any questions regarding your
warranty rights and responsibilities, you should
contact Caterpillar at 1-844-797-6387 or E-mail:
homeandoutdoorpower@cat.com
Defects Warranty Requirements:
(a) The warranty period begins on the date the
engine/equipment is delivered to an ultimate
purchaser.
(b) General Emissions Warranty Coverage.
Caterpillar warrants to the ultimate purchaser
and each subsequent owner that the engine or
equipment is:
(1) Designed, built, and equipped so as to
conform with all applicable regulations adopted
by the Air Resources Board; and
(2) Free from defects in materials and workmanship
that causes the failure of a warranted part for a
period of three years
(c) The warranty on emission-related parts will be
interpreted as follows:
(1) Any warranted part that is not scheduled for
replacement as required maintenance in the
written instructions must be warranted for the
warranty period defined in Subsection (b)(2). If
any such part fails during the period of
warranty coverage, it must be repaired or
replaced by Caterpillar according to
Subsection (4) below. Any such part repaired
or replaced under the warranty must be
warranted for the remaining warranty period.
(2) Any warranted part that is scheduled only for
regular inspection in the written instructions
must be warranted for the warranty period
defined in Subsection (b)(2). A statement in
such written instructions to the effect of “repair
or replace as necessary” shall advise owners
of the warranty coverage for emissions related
parts. Replacement within the warranty period
is covered by the warranty and will not reduce
22
the period of warranty coverage. Any such part
repaired or replaced under warranty must be
warranted for the remaining warranty period.
(3) Any warranted part that is scheduled for
replacement as required maintenance in the
written instructions must be warranted for the
period of time prior to the first scheduled
replacement point for that part. If the part fails
prior to the first scheduled replacement, the
part must be repaired or replaced by
Caterpillar according to Subsection (4) below.
Any such part repaired or replaced under
warranty must be warranted for the
remainder of the period prior to the first
scheduled replacement point for the part.
(4) Repair or replacement of any warranted part
under the warranty provisions must be
performed at no charge to the owner at a
warranty station.
(5) Notwithstanding the provisions of Subsection
(4) above, warranty services or repairs must
be provided at distribution centers that are
franchised to service the subject
engine/equipment.
(6) The owner must not be charged for diagnostic
labor that leads to the determination that a
warranted part is in fact defective, provided
that such diagnostic work is performed at a
warranty station.
(7) Caterpillar is liable for damages to other
engine/equipment components proximately
caused by a failure under warranty of any
warranted part.
(8) Throughout the emissions control system's
warranty period set out in subsection (b)(2),
Caterpillar must maintain a supply of
warranted parts sufficient to meet the expected
demand for such parts and must obtain
additional parts if that supply is exhausted.
(9) Manufacturer-approved replacement parts that
do not increase the exhaust or evaporative
emissions of the engine or emissions control
system must be used in the performance of
any warranty maintenance or repairs and must
be provided without charge to the owner. Such
use will not reduce the warranty obligations of
Caterpillar.
(10) Add-on or modified parts that are not
exempted by the Air Resources Board may not
be used. The use of any non-exempted add-on
or modified parts will be grounds for
disallowing a warranty claim. Caterpillar will
not be liable to warrant failures of warranted
parts caused by the use of a non-exempted
add-on or modified part.
(11) Caterpillar issuing the warranty shall provide
any documents that describe that warranty
procedures or policies within five working days
of request by the Executive Officer.
(d) Emission Warranty Parts List for exhaust
(1) Fuel Metering System
(i) Carburetor and internal parts (and/or
pressure regulator or fuel injection system)
(ii) Air/fuel ratio feedback and control system
(iii) Cold start enrichment system
(2) Air Induction System
(i) Controlled hot air intake system
(ii) Intake manifold
(iii) Air filter
(3) Ignition System
(i) Spark plugs
(ii) Magneto or electronic ignition system
(iii) Spark advance/retard system
(4) Exhaust Gas Recirculation (EGR) System
(i) EGR valve body, and carburetor spacer if
applicable
(ii) EGR rate feedback and control system
(5) Air Injection System
(i) Air pump or pulse valve
(ii) Valves affecting distribution of flow
(iii) Distribution manifold
(6) Catalyst or Thermal Reactor System
(i) Catalytic converter
(ii) Thermal reactor
(iii) Exhaust manifold
(7) Particulate Controls
(i) Traps, filters, precipitators, and any other
device used to capture particulate emissions
(8) Miscellaneous Items Used in Above Systems
(i) Electronic controls
(ii) Vacuum, temperature, and time sensitive
valves and switches
(iii) Hoses, belts, connectors, and assemblies.
(e) Emissions Warranty Parts List for
Evaporative Emissions
(1) Fuel Tank
(2) Fuel Cap
(3) Fuel Lines (for liquid fuel and fuel vapors)
(4) Fuel Line Fittings
(5) Clamps*
(6) Pressure Relief Valves*
(7) Control Valves*
(8) Control Solenoids*
(9) Electronic Controls*
(10) Vacuum Control Diaphragms*
(11) Control Cables*
(12) Control Linkages*
(13) Purge Valves*
(14) Gaskets*
(15) Liquid/Vapor Separator
(16) Cabon Canister
(17) Canister Mounting Brackets
(18) Carburetor Purge Port Connector
*Note: As they relate to the evaporative
emission control system
23
WARRANTY
CATERPILLAR LIMITED WARRANTY
FOR INVERTER GENERATOR MODEL:
INV1250, INV2000, INV2250
Purchased in the United States and Canada
Caterpillar (Newberry) LLC. (Caterpillar) warrants to the original purchaser that any new Cat® branded portable generator products purchased in the
United States and Canada are free from defects in materials and workmanship for the warranty period set forth below, provided that the product is
operated and maintained in accordance with Caterpillar's instructions and manuals. Caterpillar will, at its option, repair or replace any part which, upon
inspection by Caterpillar or a Caterpillar authorized service representative, is found to be defective during the warranty period as set forth below. Any
product that the purchaser claims to be defective must be returned to and examined by the nearest Caterpillar authorized service representative
located in the United States or Canada. Transportation and associated costs and risk of loss are the responsibility of the purchaser.
Warranty Period:
All new inverter generator products are warranted under normal use for a period of two (2) years from the date of original purchase or under commercial
use for a period of (6) months from the date of original purchase. If proof of original purchase is not presented, the manufacturer's shipping date will
be used to determine the start of the warranty period. To help with any warranty claims, the original purchaser should register the product on
www.cat.com/homeandoutdoorpower-support immediately following the purchase.
By means of registering the product on www.cat.com/homeandoutdoorpower-support within thirty (30) days from the date of purchase, original
purchasers have the option to extend the Warranty Period by one additional year for a total of three (3) years calculated from the date of original
purchase of the product.
This Warranty shall NOT apply to the following:
1. Damage or deterioration caused by normal wear and tear.
2. Failures caused by any external cause or act of God, such as
accident, collision, theft, vandalism, riots, wars, fire, freezing,
lightning, earth-quakes, windstorms, hail, volcanic eruptions,
floods, tornados or hurricanes.
3. Failures due to alterations, adjustments, unauthorized fuel setting
changes, neglect or improper storage, repair and/or maintenance.
4. Failures due to abuse or application of the product for uses other
than for which it is designed or intended to by the manufacturer,
including but not limited to, improper installation or location in a
contaminated, harsh, corrosive or saltwater environment.
5. Failures resulting from attachments, accessory items, and parts
not sold, issued or approved by Caterpillar.
6. Failures caused by contaminated or improper fuels, fuels, oils or
other operating media or improper fluid levels.
7. Failures resulting from user’s delay in making the product
available after being notified of a potential product problem.
8. Cosmetic damage, discolorations, rusting, corrosion or scratches
to applied paint.
9. Replacement of consumables such as, but not limited to, fuses,
lamps, filters, etc.
10. Repair by any party other than a Caterpillar authorized service
representative.
11. Additional expenses for repair after normal business hours, i.e.
overtime or holiday labor rates.
12. Expenses for rental of equipment during downtime and/or
performance of warranty repairs.
13. Expenses related to investigating performance complaints and/or
troubleshooting where no manufacturing defect is found.
14. Starting batteries are NOT covered under this warranty but will be
covered under the portable generator parts warranty.
To obtain warranty service or if you have questions concerning this warranty or its applications, please call 1-844-797-6387 or visit
www.cat.com/homeandoutdoorpower-support, where you can also search for your nearest authorized Cat service representative.
CONSUMER ARBITRATION CLAUSE: MANDATORY BINDING INDIVIDUAL ARBITRATION
INSTEAD OF COURT; CLASS ACTION WAIVER
a. You and Caterpillar both agree that, to the extent permitted by
applicable law, any and all disputes or claims arising out of or
relating in any way to Cat Branded portable generator products or
services related thereto, or from any advertising for any such
products or services, including any question regarding the
existence, validity, or termination of this Caterpillar Limited
Warranty, as well as any issue regarding the interpretation of the
terms and conditions of this Consumer Arbitration Clause will be
resolved by binding arbitration before a sole arbitrator, rather than
in court, except that you may assert claims in small claims court if
your claims qualify. This also includes any claims that arose before
you accepted this Caterpillar Limited Warranty, regardless of
whether prior versions of the Limited Warranty required arbitration.
In the US, The Federal Arbitration Act (9 U.S.C. § 1 et seq.) and
federal arbitration law apply to the Caterpillar Limited Warranty and
the terms and conditions of this Consumer Arbitration Clause.
b. Arbitration uses a neutral arbitrator instead of a judge and jury. An
arbitrator can award on an individual basis the same damages and
relief as a court (including injunctive and declaratory relief or
statutory damages) and must follow theterms of this Limited
Warranty (including the terms and conditions of this Consumer
Arbitration Clause) as a court would. Arbitration procedures allow
for more limited discovery, and court review of an arbitration award
is limited.
c. If you have a dispute and elect to seek arbitration or file a claim in
small claims court, you must first send to Caterpillar, by certified
mail, a written notice of your claim that (a) describes the nature
and basis of the claim or dispute; (b) sets forth the specific relief
sought and (c) includes a physical address and email address
where you may be reached ("Notice"). The Notice must be
addressed to: General Counsel, Caterpillar Inc., 100 N.E. Adams
St. Peoria Illinois 61629 (“Notice Address”) and reference a
“Notice of Claim under Caterpillar Limited Warranty.” If Caterpillar
and you do not reach an agreement to resolve the claim within 60
days after the Notice is received, you or Caterpillar may
commence an arbitration proceeding or file a claim in small claims
court.
d. You may download or copy a form to initiate arbitration at
www.adr.org. If you are required to pay a filing fee, after
Caterpillar receives notice at the Notice Address that you have
commenced arbitration, Caterpillar will reimburse you for your
payment of the filing fee, unless your claim is for greater than
US$25,000, in which case you will be responsible for filing fees.
24
e. The arbitration will be governed by the AAA’s then current
Consumer Arbitration Rules, as modified by the terms set forth in
this Limited Warranty (including the terms and conditions of this
Consumer Arbitration Clause), and will be administered by the AAA.
The AAA Rules and Forms are available online at www.adr.org or
by calling the AAA at 1-800-778-7879. In the event of any conflict
between the terms set forth herein and the AAA Consumer
Arbitration Rules, these terms will apply.
f. If your claim totals less than US$25,000, Caterpillar will pay for all
administrative and arbitration fees, including the arbitrator’s
compensation, and will reimburse you for any administrative and
arbitration fees that you incur. If your claim exceeds US$25,000,
the parties will pay equal shares of any administrative and
arbitration fees, including the arbitrator’s compensation, except for
such fees that the AAA Consumer Arbitration Rules require
Caterpillar to pay in full. Each party will bear the expense of its own
counsel, experts, witnesses, and preparation and presentation of
evidence at any arbitration hearing.
g. If your claim is for US$25,000 or less, you and Caterpillar agree that
you may choose whether the arbitration will be conducted solely on
the basis of documents or through a telephonic hearing. You may
also request an in-person hearing, which the arbitrator may grant at
his or her discretion. If the arbitrator grants an in-person hearing,
such hearing will be conducted either at a mutually agreed location
or a location determined by the AAA or the arbitrator. In such an inperson hearing, the parties, or any of their witnesses, have the right
to participate remotely by way of videoconference or some similar
means. If your claim exceeds US$25,000, the right to a hearing will
be determined by the arbitrator.
h. You and Caterpillar agree that, to the extent permitted by applicable
law, any dispute resolution proceedings, whether in court or before
an arbitrator, will be conducted only on an individual basis and not
in a class, representative, consolidated, or mass action. Neither you
nor Caterpillar may join or consolidate claims by or against a third
party, or arbitrate or otherwise participate in any claim as a class
representative, class member or in a private attorney general
capacity. If this provision is found to be unenforceable, then the
entirety of the terms and conditions of these Dispute Resolution and
Arbitration paragraphs (other than paragraph (k)) shall be null and
void.
i. Any arbitration will be confidential. Neither you, Caterpillar, the AAA,
nor the arbitrator may disclose the existence, content (including any
oral or written submissions), or results of any arbitration, except as
may be required by law or for purposes of enforcing or challenging
of the arbitration award.
j. You may opt out of this dispute resolution procedure by providing
written notice to Caterpillar at the Notice Address no later than 30
calendar days from the date of your purchase of Caterpillar products
or services (or date of first use, in the case of free products or
services) covered by this Limited Warranty. Opting out of this
dispute resolution procedure will not otherwise affect the coverage
or applicability of the Limited Warranty, or your ability to purchase
or use Cat branded portable generator products or services, in any
way.
k. If for any reason a claim proceeds in court rather than in arbitration
or small claims court, including if you opt out under paragraph (j), to
the extent permitted by applicable law, we each waive any right to
a jury trial and agree that any such proceeding shall be conducted
only on an individual basis and not in a class, representative,
consolidated, or mass action. Under such circumstances, you and
Caterpillar agree that, to the extent any dispute arises out of a Cat
branded portable generator sold in the US, the federal and state
courts of the State of Illinois have exclusive jurisdiction to hear and
determine any such claim, consent to the personal jurisdiction of
any federal or state court in the State of Illinois, and acknowledge
that venue is proper in any judicial district within the State of Illinois.
If any part of these Dispute Resolution and Arbitration provisions or
this paragraph (k) is found to be unenforceable, the remainder of
these Dispute Resolution and Arbitration Provisions and this
paragraph (k) shall still be given full force and effect.
l. In the event that any provision of this agreement is found to be
invalid or unenforceable in a particular case or jurisdiction, that
provision will be severable in that case or jurisdiction, as the case
may be, without affecting the validity and enforceability of the
remaining provisions of the agreement, and shall not affect the
validity and enforceability of the agreement in other cases and
jurisdictions.
Applicable Law
m. By purchasing or using any Cat branded portable generator product
or service related thereto, you agree that, to the degree permitted
by applicable law, the Federal Arbitration Act, applicable federal
law, and laws of the State of Illinois, without regard to its conflict of
laws rules, will govern the terms of this Limited Warranty, as well as
any dispute of any sort that might arise between you and Caterpillar
relating to such products or services.
n. If a dispute arises out of a Cat branded portable generator sold in
Canada the foregoing dispute resolution and arbitration terms will
apply to the extent permitted by applicable law. If the foregoing
terms are not binding upon you under the applicable law of your
jurisdiction, and the dispute is within the jurisdiction of the small
claims court in your province, you may choose to take your claim to
that court. If the dispute exceeds the jurisdiction of the small claims
court in your province, you agree to submit to the jurisdiction of the
courts within your province for the purpose of litigating all claims,
disputes, actions or causes of action, issues or requests for relief
arising out of or relating to this Limited Warranty, which courts shall
have exclusive jurisdiction over all such claims, disputes, actions or
causes of action, issues or requests for relief.
Limitations
THIS WARRANTY IS IN PLACE OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED. SPECIFICALLY, CATERPILLAR MAKES NO
OTHER WARRANTIES AS TO THE MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. CATERPILLAR'S ONLY LIABILITY
SHALL BE THE REPAIR OR REPLACEMENT OF PART(S) AS STATED ABOVE. IN NO EVENT SHALL CATERPILLAR BE LIABLE FOR ANY
INCIDENTAL OR CONSEQUENTIAL DAMAGES, EVEN IF SUCH DAMAGES ARE A DIRECT RESULT OF CATERPILLAR'S NEGLIGENCE.
This warranty is subject to and shall not apply in contravention of the laws or other legal compliance requirements of the United States or any other
applicable jurisdiction, without recourse or liability with respect to Caterpillar.Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation may not apply to you. This warranty gives you specific legal rights. You may also have other rights
from state to state, or territory.
In USA and Canada: Caterpillar Newberry LLC, Electric Power
Division, 40 Mawsons Way, SC 29108-6400, Attention:Customer
Service Manager, Telephone (844)-797-6387. Outside the USA and
Canada: Contact your Authorized Service Representative
www.cat.com/homeandoutdoorpower-support or email
homeandoutdoorpower@cat.com.
© 2020 Caterpillar. All Rights Reserved. CAT, CATERPILLAR,
LET’S DO THE WORK, their respective logos, "Caterpillar Yellow", the
"Power Edge" and Cat “Modern Hex” trade dress as well as corporate
and product identity used herein, are trademarks of Caterpillar and
may not be used without permission.
www.cat.com/homeandoutdoorpower
Loading...