Casio KX-716B, QV-3000EX/Ir, KX-716D, KX-716F, KX-716C Service Manual & Parts List

QV-3000EX
(KX-716B)
QV-3000EX/Ir
(KX-716C/D/F)
FEB. 2000
(without price)
R
SPECIFICATIONS ....................................................................................................................................... 1
To distinguish the model .......................................................................................................................... 3
BLOCK DIAGRAM ...................................................................................................................................... 4
CIRCUIT BLOCK.........................................................................................................................................5
ADJUSTMENT ............................................................................................................................................ 6
1. Program version upgrading..............................................................................................................7
1-1. How to confirm the program (graphic menu) version.............................................................. 7
1-2. Upgrading procedure using the CompactFlash card............................................................... 7
1-3. Upgrading procedure using the PC link cable..........................................................................8
2. Test mode........................................................................................................................................... 9
2-1. Booting ......................................................................................................................................... 9
2-2. Item for testing.............................................................................................................................9
3. Product conditions .......................................................................................................................... 11
3-1. Color adjustment data writing.................................................................................................. 11
3-2. Flash adjustment ....................................................................................................................... 19
3-3. Flash operation and recharge operation................................................................................. 20
3-4. Current consumption ................................................................................................................ 21
3-5. VCOM DC adjustment................................................................................................................ 22
3-6. Operation check......................................................................................................................... 23
4. D-PCB Assy ...................................................................................................................................... 24
4-1. VCO free run frequency adjustment ........................................................................................ 24
4-2. VCOM AC adjustment and VCOM DC coarse adjustment ..................................................... 24
4-3. RGB AMP, Sub bright adjustment............................................................................................ 25
4-4. Contrast, Bright adjustments ................................................................................................... 26
4-5. Color adjustment ....................................................................................................................... 27
4-6. TINT adjustment......................................................................................................................... 28
5. PW-PCB Assy...................................................................................................................................29
5-1. VCC3, VCC3-M, VCC5, VCC7 Voltage check ........................................................................... 29
5-2. VCC15, VEE7 Voltage check..................................................................................................... 29
5-3. BL drive voltage adjustment..................................................................................................... 29
DISASSEMBLY/ASSEMBLY .................................................................................................................... 30
EXPLODED VIEW ..................................................................................................................................... 46
PARTS LIST .............................................................................................................................................. 47
PRINTED CIRCUIT BOARDS ................................................................................................................... 49
SCHEMATIC DIAGRAMS ......................................................................................................................... 55
SPECIFICATIONS
File Format Still images (including panoramas): JPEG (Exif. Ver . 2.1), DCF standard (Design rule for Camera
File system), DPOF compatible, Movies: AVI
Recording Medium CompactFlash card (Type I/II) Recorded image Size 2048 x 1536 pixels, 1024 x 768 pixels Standard Memory Capacity,Number of Image Files,Computer Output Image Size
Still
Image size
(pixels) 8 MB memory card 64MB memory card 340MB Microdrive
2048 FINE 1.4 MB/images 5 images 43 images 245 images
x NORMAL 1 MB/images 6 images 60 images 342 images 1536 ECONOMY 600 KB/images 11 images 99 images 562 images 1024 FINE 350 KB/images 19 images 167 images 943 images
x NORMAL 250 KB/images 27 images 229 images 1292 images
768 ECONOMY 150 KB/images 43 images 365 images 2054 images
Storage Capacity Approxmately 300 KB/second Recording Time 30 seconds per movie (NORMAL)
Quality File size
Movie
10 seconds per movie (PAST)
The maximum length of a single movie is 10 seconds.
Image Deletion Single image; all images in a folder; all images in memory (with image protection) Imaging Element 1/1.8-inch CCD (Total Pixels: 3.34 million, Effective Pixels; 3.24 million) Lens F2 to 2.5; f = 7 to 21mm (equivalent to 33 to 100mm lens for 35mm film) Zoom Optical zoom, 8X; Digital zoom: 32X (in combination with optical zoom)
Image size is 1024 x 768 pixels when digital zoom is used.
Focusing Contrast-detect Auto Focus; manual focus with macro mode and focus lock Focus Range Normal focus: 0.3m to (1´ to ∞)
Macro focus: 6cm to 30cm (2.4˝ to 11.8˝) (1X zoom)
9cm to 30cm (3.5˝ to 11.8˝) (2X zoom)
The focusing range is the distance from the lens surface to the subject.
Exposure Control Light Metering: Multi-pattern, center point, spot by CCD
Exposure: Program AE, Shutter priority AE, Aperture priority AE Exposure Compensation: –2EV to +2EV (1/3EV units) Exposure Range: Approximately EV7 to EV16
Shutter CCD electronic shutter; mechanical shutter, 2 to 1/1000 second Aperture F2 to F8, auto switching or manual switching White Balance Automatic, fixed (4 modes), manual switching Self-timer 10 seconds, 2 seconds Built-in Flash Flash Modes: AUTO, ON, OFF, Red eye reduction
Flash Range: Approximately 0.5 to 4 meters (1.6´ to 13.1´)
Recording Functions One-shot, continuous, movie, panorama, landscape, night scene, portrait, self-timer, macro Monitor 1.8" TFT, low-glare color HAST LCD (122,100 pixels, 555 x 220) Viewfinder LCD Monitor or optical viewfinder Clock Built-in quartz digital timepiece for time and date recording and storage with image data; auto
calendar up to 2049
Input/Output Terminals DIGITAL IN/OUT, USB port (special mini port), AC adaptor connector, VIDEO OUT (NTSC,
PAL)
Infrared Communication IrDA; IrTran-P (QV-3000EX/Ir only)
Number of images
— 1 —
Power Supply Four AA-size alkaline or lithium batteries
Four AA-size nickel-metal hydride rechargeable batteries (NP-H3) AC adaptor (AD-C620)
AC adaptor charger (BC-3HA)
Battery Life The values noted below indicate the number of hours before battery failure under normal
operating temperature (25°C). These values are for reference only, and do not guarantee that any particular set of batteries actually will provide the service life indicated. Low temperatures shorten battery life.
Type of Operation
Continuous Playback
Continuous Recording
• The above figures are approximations only.
• The above guidelines are based on the following battery types: Alkaline: MX1500 (AA) DURACELL ULTRA Lithium: Energizer
• Battery life varies with brand. Continuous recording values show the number of shots without using the flash. The number of shots depends on use of the flash and whether flash is turned on or off.
Power Consumption Approximately 6.6W Dimensions 134.5(W) x 80.5(H) x 57.5(D) mm (5.3˝(W) x 3.2˝(H) x 2.3˝(D)) Weight Approximately 320g (11.2 oz) (excluding batteries) Standard Accessories Neck strap; lens cap; cap holder; soft case; USB cable; video cable; User’s Manual
•This camera does not have a separate battery to power its clock. Clock settings are cleared whenever power to the camera is cut off (by batteries going dead while the camera is not connected to an AC power outlet with the AC adaptor) for about 24 hours. After power is resumed, either by loading fresh batteries or connecting to an AC power outlet, you will have to set the correct time and date again.
•The liquid crystal panel built into this camera is the product of precision engineering, with a pixel yield of 99.99%. This also means, however that 0.01% of the pixels can be expected to fail to light or to remain lit at all times.
AA-size Alkaline Batteries LR6
Approximately 145 minutes
Approximately 210 shots
AA-size Lithium Batteries FR6
Approximately 270 minutes
Approximately 900 shots
AA-size Ni-MH Batteries NP-H3
Approximately 170 minutes
Approximately 660 shots
— 2 —
To distinguish the model
MODE
MF/ / /
MODE
MF/ /
Discriminate between infra-red model and non-infra-red model by the following points.
QV-3000EX (KX-716B) for U.S.A
REC
MF/ /
OFF
PLAY
MENU
SET
PREVIEW
DISP
MODE
T
W
QV-3000EX/Ir (KX-716C/D/F)
REC
MF/ / /
OFF
PLAY
MENU
SET
PREVIEW
DISP
MODE
T
W
Infra-red transmission button.
Infra-red transmission button.
— 3 —
— 4 —
BLOCK DIAGRAM
KA-
PCB
TELE WIDE DISP
PREVIEW
SUB-LCD
SUB-PCB
51pin
RTC
RTC-4574
SUB
Microprocessor
HD404889
BACK UP Capacitor
4.0 MHz
KB-
PCB
+,–
ENTER
MENU
3pin
4pin
80pin
CF
VCC7 (8.0V)
BLVCC (5.4V)
VCC3
(3.3V)
DOWN
Converter
CCD/LCD
Power
VCC15 (15.0V)
VEE7
(-7.5V)
VCC5 (5.0V)
CF
LED
IrDA
Controller
48.0MHz
CCD-FPC
KEY MODE TIMER MACRO FLASH SHUTTER(Half/Full)
BL UNIT
3pin
D-PCB
26pin
LCD Module
V
DD: 3.3V VGH: 15.0 VGL: -15.0V
VSH: 5.0V
CDS/AGC/ADCAD9803
MPU
LR38664Y
TFT
Controller
CM7019L3
Chroma I/F
IR3Y29B
29.5 MHz
24.0 MHz
24.5454 MHz
SDRAM
(64M X 2)
FLASH/
MASK (16M)
EEPROM
(4K)
TGCXD2497R
36.0 MHz
5.0 MHz
MD
Microprocessor
SW
CF
Controller
6pin
16pin
19pin
CCD
LENS BLOCK
Canon
Zoom X 3
FINDER
UNIT
ICX252AQ
3.58 MHz
REG
Vertical/Horizontal
Sensor
EVCC(3.3V)
AF DRIVER
IRIS/SHUTTER
DRIVER
ZOOM DRIVER
BUS BUFFER
TC74AC367 X 2
SW-PCB
BL-PCB
VCC3-M (3.4V)
PW-PCB
AC
Flashing
Controller
Photp
Sensor
ADPT
ST-PCB
10pin
B to B
10pin
Charging
Booster
SJ-PCB
FLASH
FOCUS
LED
SERIAL BUFFER
VIDEO DRIVER
USB TRANSCEIVER
Buzzer
REC/
PLAY /
OFF
SHUTTE
R
LED-PCB
SELF
LED
VCC5
(5.0V)
CF
SW
,
Flash
Control
Motor system
step-down
transformer
LCD booster
BL booster
Logic circuit
step-down
transformer
CIRCUIT BLOCK
PCB Circuit Block Outline Main Devices Note
PW LCD Power Supply 7.5V Up Converter XC6367B101MR Newly employed part
BL Power Supply 5.4V Up Converter XC6367A542MR Newly employed part Main Power Supply 3.3V Non adjustable step down transformer XC6365A333MR Newly employed part CCD 5V Power Supply 5.0V Voltage regulator XC62ER5002MR Newly employed part LCD Power Supply Flash Control Power Video Driver Power Supply CCD & LCD Power Supply Power specifications (+15V, -7.5V) MAX685EEE Used on QV-8000SX Lens Unit AP Power 3.3V Non adjustable step down transformer XC6365B103MR Newly employed part Lens Unit Zoom Power Lens Unit AE Power Charging Booster Circuit 300V Booster Used on QV-8000SX
Current control circuit
Charging control circuit Charging Comparator Light emission control circuit Used on QV-8000SX CF Connector Complying to TYPE-II (Reverse insertion) Used on QV-2000UX
D MPU Processor Interface LR38664Y Newly employed part
Serial Interface CSP package
CCD Interface
NTSC/PAL Encoder
JPEG
DMA Controller
BUS Interface Flash Memory 16 Mbit (1 M X 16 bit) Flash Memory LH28F160S3B Compatible with the Mask ROM (Mask ROM) CSP package SDRAM 64 Mbit ( 1 Mword X 16 bit X 4 bank) X 2 K4S641632C-TL1 and others CF Controller CF controller and I/O interface uPD65839GC Used on QV-2000UX TFT-LCM 1.8" high definition TFT (HAST) C0D18T1035FN Newly employed part LCD Controller Complying to high definition TFT (HAST) CM7019L3-T4N Newly employed part
3.0V driver
Chroma Interface +5V/+7.5V source, C-VIDEO input IR3Y29BM Used on QV-770
Brightness fixed Stand-by power 3.3V three-terminal regulator XC62FP3302MR Newly employed part 8-bit MPU Driving motor control D780034AGK-A03-8A8
Flash ROM built in -> Mask ROM after MP EEPROM 4Kbit (256word x 16bit) BR93LC66FV-E2 Used on QV-2000UX AF//ZOOM AF ZOOM is 1-2-phase excitation LB1846M Newly employed part Motor driver AE is 2-phase excitation Shutter/ AE driver LB1837M-TE-L Newly employed part USB tranceiver PDIUSB11AP Used on QV-8000SX Video 75 ohm dirver TK15405MTL Used on QV-8000SX Serial transport driver Used on QV-7000SX TG/V/H driver for 3340 thousand picture element CCD (35.0MHz clock) CXD2497R Newly employed part CDS/AGC/ADC CDS AD9803JSTRL Used on QV-8000SX
11bit Programmable Gain Amplifier
10-bit A/D converter Vertical/Horizontal sensor 4-way tilt sensor Alps electronics Used on QV-2000UX
SUB IrDA Controller IrDA Controller and Serial Controller PC87109VBE Used on QV-7000SX
IrDA Module Small-type IrDA moule (IrDA1.1) HSDL-3600 Used on QV-2000UX 4bit Microprocessor Power ON sequence HD404889 (Mask ROM) Key scanning
Beep control
I/O and others RTC Built-in 32KHz clock real time clock RTC-4574JE Used on QV-2000UX Backup Capacitor Watch backup (24H) EECS0HD104H Used on QV-2000UX SUB-LCD Used on QV-2000UX
BL Inverter Circuit BL unit Used on QV-2000UX
SW PW ON/OFF Newly employed part
BB-PCB Board-toBoard connection PCB Used on QV-2000UX KEY SW KA-PCB, KB-PCB
CCD CCD 1/1.8 inch, 3,340,000 picture element ICX252AQ Newly employed part
— 5 —
Preparation
1. PC (IBM Compatible)/OS:Windows 95/98
2. Link cable.
3. Adjustment program
1) ADJ716.EXE (Color adjustment data transfer program)
2) FLOAD.EXE (Camera unit version up program)
3) _ROM.BIN (Camera unit program data)
4) _GMENU.BIN (Camera unit menu display data)
4. AC adaptor or stabilizer
5. Digital oscilloscope
6. Multimeter
7. Ammeter
8. Frequency counter
9. TV (with video terminal)
10. Video cable
11. Battery (battery operation/battery cover lock)
ADJUSTMENT
12. PC link program : Photo Loader (Communication function confirmation)
13. USB cable/USB driver (USB function confirmation)
14. Test chart (for photography check) That which carried out color printing of picture data "CHART1.JPG" and the "CHART2.JPG".
CHART2.JPGCHART1.JPG
— 6 —
1. Program version upgrading
In the camera unit, program and graphic menu are stored. Please check the version and update it if the version is not updated. There are two method of program updating; using CompactFlash card or utilizing PC link cable.
Note:
1. Be sure to use AC adaptor. PCB D becomes unusable if power down or an error occurs during program transmission.
2. Unit using a mask cannot update the program.
1-1. How to confirm the program (graphic menu) version
1. Boot the test mode. Turn the power on while pressing DISP and MENU buttons simultaneously.
2. Check the LCD display.
(Example)
TEST MODE PROG 00. 02. 04. 13. 49 r Program version GMENU 99. 12. 27. 18. 12 r Graphic menu version
· · · ·
1-2. Upgrading procedure using the CompactFlash card
(1) Copy the latest program ( _ROM.BIN) and graphic menu ( _GMENU.BIN) on a CompactFlash card
then set the CompactFlash card on the camera.
(2) Connect an AC adaptor on the camera. (3) Boot the test mode.
Turn the power on while pressing DISP and MENU keys simultaneously.
(4) Camera's display shows the followings.
It is normal if two OK's are shown after about 1 minute. After then, the camera is set on the Camera mode automatically. SIZE OK 666464 SIZE OK 1305532
(5) Turn the camera off. (6) Chgange the CompactFlash card with the one for picture taking. (7) Boot the test mode and confirm the program version.
Turn the power on while pressing DISP and MENU buttons.
(8) Finally, check the camera's function (shooting and playback).
— 7 —
1-3. Upgrading procedure using the PC link cable
(1) Turn the camera off and extract CompactFlash card. (2) Connect PC link cable. (3) Boot the transmission program (FLOAD.EXE). (4) Choose program file ( _ROM.BIN) or graphic menu file ( _GMENU.BIN).
(5) Select data transmission speed (115K/57K/38K).
(If errors occur, lower the transmission speed.)
(6) Click Progress button. (7) Connect an AC adaptor on the camera and turn the camera on. (8) Data transmission starts.
(9) Data transmission is completed normally when Status box shows "program complete." (10) Disconnect AC adaptor plug (cannot be turned off by the power switch). (11) Change the CompactFlash card with one for shooting. (12) Boot the test mode and confirm the version.
Turn the camera on while pressing DISP and MENU buttons.
(13) Shoot a picture and confirm the camera function (shooting and playback.)
— 8 —
2. Test mode
Note: Do not perform the menu item unless explained here. (It may damage the internal data and
camera becomes unusable.)
2-1. Booting
To boot the test mode;
Turn the camera on while pressing DISP and MENU buttons.
To boot MENU1
Press PREVEIW PREVEIW MENU keys in order rapidly.
To boot MENU2
Press FLASH FLASH MENU keys in order rapidly.
* To execute
Use + or – keys to select a test item then press shutter button to execute it.
To boot MENU3
Press SELF SELF MENU keys in order rapidly.
2-2. Item for testing
1 TEST MODE
TEST MODE PROG 99.08.16.13.38 GMENU 99.07.12.15.04 LOADER 0X00000007 ADJ MOTOR 0X0000011A POWER 0X1A CCD ADJ1 YES CCD ADJ2 YES STROBE ADJ YES ZOOM ADJ YES FOCUS ADJ YES
2 MENU1
MENU1
INIT.NTSC JAPANESE
1. LED+SUBLCD
2. INIT.NTSC ENGLISH
3. CROSS HATCH
4. ANG DET CHECK
5. INIT.PAL ENGLISH
6. COLOR BAR
7. 50PERCENT GRAY
8.
TEST MODE
PROGRAM Version
Graphic Menu Version
Loader Version
ADJ Version
Motor MCU Version
Power MCU Version
CCD ADJUST 1 (Yes/No/NG)
CCD ADJUST 2 (Yes/No/NG)
STROBE ADJUST (Yes/No/NG)
ZOOM ADJUST (Yes/No/NG)
FOCUS ADJUST (Yes/No/NG)
Shown in green if all the adjustments have been done.
YES when adjustments are completed. NO when adjustments are incomplete. NG if adjustments are failed.
— 9 —
3 MENU2
MENU2
CCD ADJ ALL
1. ZOOM ADJUST
2. CCD1 (AWB AGC)
3. CCD2 (APATURE)
4. CCD3 (SHUTTER)
5. KIZU
6. IRDA MASTER
7. FOCUS ADJUST
8. STOROBE ADJUST
9.
4 MENU3
MENU3 1/3
DISPLAY LENS ADJ
1. REC INFO
2. BA TT. TEST
3. PROG+GMENU UPDATE
4. PROG UPDATE
5. GMENU UPDATE
6. CHECK SUM
7. OSD DATA CHECK
8. ERROR MESSAGE CHECK
9. SDRAM CHECK
10.
MENU3 2/3
KEY CHECK
11. LED CHECK
12. CF CHECK
13. SUB LCD CHECK
14. CF WRITE TEST
15. AF DATA SAVE
16. EEPROM TEST
17. ADJ CLEAR
18. NOISE CAPTURE
19. BAYER CAPTURE
20.
MENU3 3/3
SHUTTER CLOSE REC
21. SHUTTER SPEED CONST
22. GRAY SCALE (10STEP)
23. WHITE
24. BLACK
25. IRDA SLAVE
26. IRDA FACTORY SLAVE
27.
— 10 —
3. Product conditions
Note: Help command on adjustment window cannot be used as it uses Japanese system.
3-1. Color adjustment data writing
1. Summary
(1) QV-3000EX is a high quality digital camera and makeshift adjustments cannot cover the quality of the
camera's picture. Therefore, we have prepared set of lens ass'y that is adjusted precisely in the factory and a floppy disc containing the lens'es adjustment data as spare parts.
(2) These adjustment data are stored in the EEPROM on PCB D.
2. Repairs
It is necessary to write color adjustment data for the replacements of the following units. (1) Lens ass'y (2) PCB D (when EEPROM contents can be read) (3) PDB D and lens ass'y (when EEPROM contents cannot be read)
3. To replace the lens ass'y
(1) Connect AC adaptor and PC link cable to the camera.
Note: Connect the link cable to serial port COM1. (2) Turn the camera on to set it on PLAY mode. (3) Boot adjustment program ADJ716.EXE.
At this time, each adjustment data are 0.
— 11 —
(4) Read the adjustment data of before repairs.
Click the Receipt button. “receive OK” will be indicated and adjustment data are shown.
Reference: At this time you can save the adjustment data in your PC.
File (F) Save as (A)
Select the drive and name the file then save it.
(Note: Do not forget to put extension code ".ADJ".) (5) Write down the following numbers.
agc-6ab
strobe-pwm
(6) Replace the lens ass'y.
(Adjusted in the factory and comes with adjustment data) (7) Connect AC adaptor and PC link cable to the camera. (8) Turn the camera on and set it on PLAY mode. (9) Boot the adjustment program (ADJ716.EXE).
— 12 —
(10) Insert the floppy disc containing adjustment data of the lens ass'y in your PC and read the data.
File (F) Open (O)
Select FDD
Select adjustment data file with extension code .ADJ.
* Adjustment data file name: 9999999.ADJ
* 9999999 is the 7-digit number written on the seal stuck on the side of the lens unit.
(11) Change the following data with the number you have written on step 5 (data before replacing the lens
unit).
Caution: Never change the other data.
Agc-6db
Strobe-pwm
(12) Add the sum of three numerals agc-6db:206, white-Rgain, and white-Bgain on the checksum.
(Example) agc_6db : 206
+
white_Rgain : 78
+
white_Bgain : 163
||
checksum : 447
Note: If erroneous nuber is input, color adjustment cannot be done.
(13) Transfer the data to the camera.
Click Trans button on ADJ window.
“send OK” will be shown.
— 13 —
(14) Turn the camera off. (15) Booting the test mode, be sure that each adjustment item is YES.
Power on while pressing DISP and MENU keys simultaneously.
CCD1 CCD2 CCD3
YES YES YES
STROBE KIZU ZOOM FOCUS
YES YES YES YES
(16) Check the camera operation by shooting a picture and play it back.
— 14 —
4. To replace PCB D (in case the contents of EEPROM can be read)
(1) Connect AC adaptor and PC link cable to the camera.
Note: Connect the link cable to serial port COM1. (2) Turn the camera on to set it on PLAY mode. (3) Boot adjustment program ADJ716.EXE.
At this time, each adjustment data are 0.
(4) Read the adjustment data of before repairs.
Click the Receipt button. "receive OK" will be indicated and adjustment data are shown.
(5) Save the adjustment data in the PC.
File (F) Save as (A)
Select a drive to save data.
Name a file name then save the data.
(It is better to name the camera's serial number as the file name.)
XXXXXXXX.ADJ (Note: do not forget the extension code .ADJ.) (6) Replace the PCB D (7) Connect AC adaptor and PC link cable to the camera. (8) Turn the camera on and set it on PLAY mode. (9) Boot the adjustment program (ADJ716.EXE).
— 15 —
(10) Load the saved data of the lens unit.
(11) Transfer the data to the camera.
Click Trans button on ADJ window.
“send OK” will be shown.
(12) Turn the camera off. (13) Booting the test mode, be sure that each adjustment item is YES.
Power on while pressing DISP and MENU keys simultaneously.
CCD1 CCD2 CCD3
YES YES YES
STROBE KIZU ZOOM FOCUS
YES YES YES YES
(14) Check the camera operation by shooting a picture and play it back.
— 16 —
5. In case of replacing PCB D and lens ass'y (EEPROM on PCB D contents cannot be read)
(1) Replace PCB D and lens ass'y. (2) Connect AC adaptor and PC link cable to the camera.
Note: Connect the link cable to serial port COM1. (3) Turn the camera on to set it on PLAY mode. (4) Boot adjustment program ADJ716.EXE.
At this point, adjustment data of each item is zero.
(5) Insert the floppy disc containing adjustment data of the lens ass'y in your PC and read the data.
File (F) Open (O)
Select FDD
Select adjustment data file with extension code .ADJ.and load it.
(6) Transfer the adjustment data to the camera.
Clock Trans button on ADJ program window.
Send OK. Will be shown.
— 17 —
(7) Turn the camera off. (8) Booting the test mode, be sure that each adjustment item is YES.
Power on while pressing DISP and MENU keys simultaneously.
CCD1 CCD2 CCD3
YES YES YES
STROBE KIZU ZOOM FOCUS
YES YES YES YES
(9) Perform the function check (Record/Playback).
(10) Perform the flash adjustment.
— 18 —
3-2. Flash adjustment
1. General
Do not fail to perform this adjustment when you replace the flash unit.
2. Necessary equipment
(1) Dark room (2) AC adaptor (3) Gray paper (Superior's oxford gray No. 22)
The following sizes are available from us (also available from camra shop).
Parts code Parts name Specifications 1904 5411 Superior photographing background paper No. 22 (1.75 x 2.7m) 1904 5412 Sperior photographing background paper No. 22 (2.72 x 11m)
3. Condition
(1) Perform in a dark room. (1) Distance between flash lens and gray paper should be 1 meter. (1) Use lighter color of the gray paper.
Paper should be larger enough to fit in a picture taken from 1 meter distance.
(Reference; more than 1.5m x 2.0m)
4. Adjustment
(1) Connect an AC adaptor to the camera. (2) Set the camera in REC mode. (3) Boot the MENU2 in the test mode.
Turn the camera on while pressing DISP and MENU keys sumultaneously.
Press FLASH FLASH MENU in order quickly. (4) Using + and – keys, choose STROB ADJUST and press the shutter button. (5) When STROBE indicator appears on the right upper corner, turn the light off then press the shutter with
the above conditions. (6) The camera flashes more than 4 times. (7) Confirm the following indication and turn the camera off.
EEP WR OK
PWM XX
(8) Boot the test mode.
Turn the camera on while pressing DISP and MENU keys. (9) Make sure that STROB ADJ column is YES.
(10) Turn the camera off.
5. Block diagram
MENU
SET
Back ground paper.
1m
MF/ /
/
ACCESS
MODE
T
CARD
W
PLAY
ON/OFF
DISP
— 19 —
3-3. Flash operation and recharge operation
•Set QV-2000UX in “REC” mode.
•Normal Recording mode.
•Apply 6.0 ± 0.1 V voltage on DC in jack.
1. Preparation
(1) AC adaptor or stabilizer. (2) Ammeter. (3) TV (With video terminal). (4) Video cable.
2. Adjustment and checking
(1) Shoot a picture with flash OFF. (Make sure there is no flash) (2) Shoot a picture with flash ON and make sure it flashes once. (3) Shoot in red eye reduction mode and make sure it flashes twice. (4) Connect QV-3000EX and TV with video cable and make sure that the pictures taken in steps (2) and
(3) are not whitish, dark or erroneously colored. (5) Make sure that the charging current is less than 1.3 A.
3. Notes
(1) Excuete in a dark room. (2) Shoot a colorful object as much as possible.
QV-3000EX
(With video terminal)
TV
Video cable
— 20 —
3-4. Current consumption
•Set QV-3000EX to “PLAY” mode.
1. Preparation
(1) Voltage regulator. (2) Ammeter.
2. Adjustment procedure
(1) Current consumption (DC in = 6.0 ± 0.1 [V])
• Make sure that current consumption is less than 550 mA in PLAY mode.
• Make sure that current consumption is less than 800 mA in REC mode. (Flash charge current is not included)
(2) Lower the voltage from 6 V as shown below then make sure the battery warning indicator changes.
DC in = 5.0 ± 0.05 [V] (one indicator is off ) DC in = 4.65 ± 0.05 [V] (two indicators are off) DC in = 4.35 ± 0.05 [V] (All the indicators are off)
— 21 —
3-5. VCOM DC adjustment
1. Preparation
(1) AC adaptor or stabilizer. (2) Photo sensor/ Photo sensor amp (C2719)/L.P.F (3) Digital oscilloscope.
2. Adjustment and checking
(1) Turn the power on while pressing DISP and MENU keys simultaneously. (TEST MODE) (2) Push PREVIEW PREVIEW MENU keys in order rapidly. (TEST MODE 1) (3) Choose 50 PERCENT GRAY and execute it. (4) Monitor the photo sensor amplifier output via a low-pass filter of cutoff frequency 60Hz.
Monitoring the oscilloscope screen, adjust VR321 to minimize 60Hz ripple waveform.
3. Notes
Perform these adjustments when you replace LCD module or PCB L.
Photo diode
S1153
Photo Sensor Amp
L.P.F
C2719
R
E
C
M
F
O
/
FF
/
PLAY
LCD
/
M
O
D
M
E
N
U
SET
PREVIEW
DISP
E
T
W
Oscilloscope
Minimize the
ripple components
QV-3000EX
(Reference) Easy adjustment (1) Shot a monoscope pattern with the camera and adjust VR321 so that the best 10-step gradation is
taken.
10-step gradation
10-step gradation
Monoscope pattern
— 22 —
3-6. Operation check
1. Preparation
(1) Batteries. (2) AC adaptor. (3) PC (IBM compatible)/OS:Windows 95/98. (4) Link cable. (5) Photo loader (program). (6) TV (with video teminal). (7) Video cable. (8) USB cable/USB driver (9) Test chart (for photography check)
(That which carried out color printing of picture data "CHART1.JPG" and the "CHART2.JPG".)
2. Check matter
(1) Photography check (Please be sure to carry out.)
1 Shoot the test chart without flashing. 2 Shoot the test chart with flashing. 3 Confirm the result (compare with properly functioning camera) for;
Color
Focus and resolution
(2) Unti-shock check, Battery operations, AC adaptor operations (3) Switch operation. (4) CompactFlash insertion/pulling out movement, cover open/close operations (5) Optical zoom finder function (6) Sub LCD display check (7) Resolution, color reproduction check (8) AE function, AF function, zoom operation
(9) IrDA transmission check (model C for export only) (10) Video output, serial (3-pin) data transmission, USB function check (11) Dust and scratches on lens. (12) Appearance check
3. Note
(1) Make sure Video out setting are appropriate to your country.
(i.e. Japan=NTSC, England = PAL)
4. Test chart picture
CHART2.JPGCHART1.JPG
— 23 —
4. D-PCB Assy
4-1. VCO free run frequency adjustment
1. Adjustment procedure
• Make sure VCC5 (CP344) = 5.0 ± 0.05 [V] VCC15 (CP391) = 15.0 ± 0.45 [V] VCC7 (CP390) = 8.0 ± 0.05 [V] VCC3 (CP220) = 3.3 ± 0.08 [V]
• Room temperature should be 20 ± 10 °C
2. Preparation
• AC adaptor or voltage regulator
• Frequency counter
3. Adjustment and checking
(1) Connect SYF (CP355) and GND (CP350). (2) Monitor HDB (CP704) with frequency counter and adjust VR320 so that frequency becomes 15.734
± 0.1 KHz.
(3) After completing adjustment, disconnect SYF (CP7033) and GND (CP700).
4-2. VCOM AC adjustment and VCOM DC coarse adjustment
1. Adjustment procedure
• Make sure VCC5 (CP344) = 5.0 ± 0.05 [V] VCC15 (CP391) = 15.0 ± 0.45 [V] VCC7 (CP390) = 8.0 ± 0.05 [V] VCC3 (CP220) = 3.3 ± 0.08 [V]
2. Preparation
• AC adaptor or voltage regulator
• Frequency counter
3. Adjustment procedure
(1) Make sure amplitude of VCOM output (CP364) is 6.6 ± 0.3 V. (2) Adjust VR321 so that maximum VCOM output (CP364) will be 4.8 ± 0.2 V.
4. Note
When unable to adjust using AC adaptor, use voltage regulator and supply power to be VCC1-1 (CP105) = 5.0 ± 0.05 V.
— 24 —
4-3. RGB AMP, Sub bright adjustment
1. Adjustment procedure
• Make sure VCC5 (CP344) = 5.0 ± 0.05 [V] VCC15 (CP391) = 15.0 ± 0.45 [V] VCC7 (CP390) = 8.0 ± 0.05 [V] VCC3 (CP220) = 3.3 ± 0.08 [V]
2. Preparation
• AC adaptor or voltage regulator
• Frequency counter
3. Adjustment and checking
(1) Turn the power on while pressing DISP and MENU keys simultaneously. (TEST MODE) (2) Push PREVEIW PREVEIW MENU keys in order rapidly. (TEST MODE 1) (3) Select GRAY SCALE (10STEP) and execute. (4) Apply VCC5-1 (CP362) on the killer terminal (CP308) via 22k ohm resistor. (5) Trigger VB waveform (CP322) by FRP (CP305) signal to adjust as noted below. (6) Adjust RGB-AMP VR (VR302) so that VG waveform (CP322)’s pedestal-pedestal voltage is 4.30
± 0.05 Vp-p.
(7) Adjust SUB R BRIGHT VR (VR305) so that VR waveform (CP320)’s pedestal-pedestal voltage is 4.30
± 0.05 Vp-p.
(8) Adjust SUB B BRIGHT VR (VR304) so that VB waveform (CP324)’s pedestal-pedestal voltage is 4.20
± 0.05 Vp-p. * Make sure that waveforms are not distorted. * Proceed to CONTRAST, BRIGHT adjustments.
Power
Supply
VCC15
VCC5
VCC7
VCC3
QV-3000EX
D-PCB
(CP391)
(CP344)
(CP390)
(CP220)
Killer terminal
(CP308)
VR(CP320)
VG(CP322)
VB(CP324)
VCC5-1
22K
Digital oscilloscope
Figure 3-1
4.30 ± 0.05 or 4.20 ± 0.05V (pedestal-pedestal)
3-1
— 25 —
4-4. Contrast, Bright adjustments
1. Adjustment procedure
• Make sure VCC5 (CP344) = 5.0 ± 0.05 [V] VCC15 (CP391) = 15.0 ± 0.45 [V] VCC7 (CP390) = 8.0 ± 0.05 [V] VCC3 (CP220) = 3.3 ± 0.08 [V]
• RGB AMP and SUB BRIGHT adjustments should be completed (proceed from those adjustments.)
2. Preparation
• AC adaptor or voltage regulator
• Frequency counter
3. Adjustment and checking
(1) Turn the power on while pressing DISP and MENU keys simultaneously. (TEST MODE) (2) Push PREVEIW PREVEIW MENU keys in order rapidly. (TEST MODE 1) (3) Select GRAY SCALE (10STEP) and execute. (4) Apply VCC2-1 (CP344) on the killer terminal (CP308) via 22k ohm resistor. (5) Trigger VB waveform (CP322) by FRP (CP305) signal to adjust as noted below. (6) Adjust contrast VR (VR306) so that contrast terminal voltage (CP306) is 1.50 ± 0.05 V temporary. (7) Adjust Bright VR (VR303) so that pedestal-4th step is 2.45 ± 0.05Vp-p. (8) Adjust Contrast VR (VR306) so that pedestal-10th step (white 100 %) is 2.90 ± 0.05Vp-p. (9) After the adjustment, remove the 22k ohm resistor between killer terminal (CP308) and VCC5-1 (CP362).
* Make sure that waveforms are not distorted.
Power
Supply
VCC15
VCC5
VCC7
VCC3
QV-3000EX
D-PCB
(CP391)
(CP344)
(CP390)
(CP220)
Killer terminal
(CP308)
VG(CP322)
VCC5-1
22K
Digital oscilloscope
Figure 3-2
2.90 ± 0.05 V
(pedestal-10 step)
3-2
— 26 —
4-5. Color adjustment
1. Adjustment procedure
• Make sure VCC5 (CP344) = 5.0 ± 0.05 [V] VCC15 (CP391) = 15.0 ± 0.45 [V] VCC7 (CP390) = 8.0 ± 0.05 [V] VCC3 (CP220) = 3.3 ± 0.08 [V]
• Perform this adjustment after Contrast adjustment.
2. Preparation
• AC adaptor or voltage regulator
• Frequency counter
3. Adjustment and checking
(1) Turn the power on while pressing DISP and MENU keys simultaneously. (TEST MODE) (2) Push PREVEIW PREVEIW MENU keys in order rapidly. (TEST MODE 1) (3) Select and execute COLOR BAR. (4) Trigger with FRP (CP305) signal. (5) Adjust VR300 so that pulse width of 4th VB waveform (CP324) (pedestal-peak) is 2.90 ± 0.05Vp-p. (6) Proceed to TINT adjustment.
4. Note
Perform the adjustment after (continuously from) Color adjustment.
QV-3000EX
D-PCB
(CP391)
(CP344)
(CP390)
(CP220)
Power
Supply
VCC15
VCC5
VCC7
VCC3
VB(CP324)
Digital oscilloscope
1432
2.90 ± 0.05 [Vp-p]
— 27 —
4-6. TINT adjustment
1. Adjustment procedure
• Make sure VCC5 (CP344) = 5.0 ± 0.05 [V] VCC15 (CP391) = 15.0 ± 0.45 [V] VCC7 (CP390) = 8.0 ± 0.05 [V] VCC3 (CP220) = 3.3 ± 0.08 [V]
• Perform this adjustment after Contrast adjustment.
2. Preparation
• AC adaptor or voltage regulator
• Frequency counter
3. Adjustment and checking
(1) Turn the power on while pressing DISP and MENU keys simultaneously. (TEST MODE) (2) Push PREVEIW PREVEIW MENU keys in order rapidly. (TEST MODE 1) (3) Select and execute COLOR BAR. (4) Trigger with FRP (CP305) signal. (5) Adjust VR301 so that potential difference between the 2nd and 4th pulses' height (pedestal-peak) (A
and B) of VB waveform (CP324) is less than 0.1Vp-p.
4. Note
Perform the adjustment after (continuously from) Color adjustment.
QV-3000EX
VCC15
VCC5
D-PCB
(CP391)
(CP344)
Power
Supply
VCC7
VCC3
(CP390)
(CP220)
VB(CP324)
Digital oscilloscope
1432
BA
— 28 —
5. PW-PCB Assy
5-1. VCC3, VCC3-M, VCC5, VCC7 Voltage check
1. Preparation
•AC adaptor or voltage regulator
•Multimeter
2. Adjustment procedure
•Make sure VCC3 (CP110) = 3.3 ± 0.1 [V] VCC3-M (CP111) = 3.4 ± 0.2 [V] VCC5 (CP115) = 5.0 ± 0.15 [V] VCC7 (CP950) = 8.0 [V]
3. Note
When unable to adjust using AC adaptor, use voltage regulator and supply power to be VCC1-1, 2, 3 =
5.0 ± 0.05 V.
5-2. VCC15, VEE7 Voltage check
1. Preparation
+ 0.6 – 0.7
•AC adaptor or voltage regulator
•Multimeter
2. Adjustment procedure
Adjust VR100 so that VCC15 (CP118) = 15.0 ± 0.1 [V] and make sure that VEE7 (CP117) = -7.5 ± 0.2 [V].
3. Notes
When unable to adjust using AC adaptor, use voltage regulator and supply power to be VCC1-1 (CP107) =
5.0 ± 0.05 V.
5-3. BL drive voltage adjustment
1. Preparation
•AC adaptor or voltage regulator
•Multimeter
2. Adjustment procedure
Make sure that BL-VCC (CP910) is within 5.0 ± 0.05V.
3. Notes
When unable to adjust using AC adaptor, use voltage regulator and supply power to be VCC-1-1 (CP107) =
5.0 ± 0.05 V.
— 29 —
DISASSEMBLY/ASSEMBLY
1. Put on the lens cap in order to protect scratches on the lens.
2. Open the batter y cover and remove one screw (BT3 panhead 1.4x3.5 black).
4. Slide the CN cover and remove one screw (BT3 flathead 1.7x3.5 Ni).
5-1. Remove tw o scre ws (BT3 flathead 1.7x4.0 black)
from the side of the camera. First screw
3. Remove one screw (BT3 flathead 1.7x3.5 Ni) from the bottom of the camera.
5-2. Second screw
— 30 —
5-3. When you assemble the case, screw it while CF
cover is open for better fitting.
6-1. Open the battery cover. Open the case.
7-1. Open the case from CN cover side. It is easier to
open while pushing the upper part of the strap pin.
7-2. When the case opens a little, open it from the
bottom. Be careful with the cable.
6-2. Open the case as shown on the figure.
7-3. The figure shows the opened case.
Cable
— 31 —
8-1. Desolder the gray and blue wires from D PCB.
11. Remove the green wire (SUB PCB).
8-2. Enlarged
9. Remove the cable (D PCB/ CN550).
12. Separated Upper and Lower cases.
13-1. Remove four screws (BT3 panhead 1.7 x 5.0 Ni)
that affixing the Display ass'y. First screw
10. Remove the cable (SUB PCB/ CN451).
13-2. Second screw
— 32 —
13-3. Third screw
13-4. Fourth screw
16-1. Disconnect three cables (D PCB).
CN706
16-2. CN705
14. Remove the cable (D PCB/ CN300).
15. Remove the cable (BL PCB/ CN900).
16-3. CN200
17-1. Disconnect four wires (D PCB).
— 33 —
17-2. Green wire
17-3. White wire
18-1. Remove D PCB by opening it from the upper part.
Caution: Be careful with the cable under the PCB.
18-2. When Lower case and D PCB are removed.
17-4. Black wire
17-5. Yellow wire
19-1. Remove two wires (D PCB).
19-2. Orange wire
— 34 —
19-3. Black wire
22-2. Second screw
20. D PCB is removed from Lower case.
21. Peel off the cloth on J frame.
23. Remove J frame.
24. Disconnect cable (SJ PCB/ CN100).
22-1. Remove two screws (BT3 panhead 1.7x5.0 Ni)
from J frame. First screw
25. Remove one screw (BT3 panhead 1.7 x 5.0 Ni) from Battery frame.
— 35 —
26. Remove one screw (BT3 panhead 1.4 x 3.5 Black) from Battery frame.
27. Remove one screw (BT3 flathead 1.7 x 4.0 Black) from side body.
30. Displace BB PCB.
31-1. Peel cloth tape from CCD block.
Caution: When you assemble, set the lead wires and cloth tape as shown on the figure below.
28. Peel the cloth tape that affix the cable.
29. Remove Battery Frame.
31-2. After the cloth tape is peeled off.
— 36 —
32-1. Disconnect the lead wire from CCD PCB.
Caution: Leave the other wires.
32-2. After the lead wire is removed.
33-2. Second screw
33-3. Third screw
33-1. Remove three screws (BT3 panhead 1.7 x 5.0
Ni) which affix CL unit. First screw
34. Remove CL unit.
35. After removal of CL unit.
— 37 —
36-1. Discharge the capacitor for the flash via 1.5kohm,
5W resistor.
36-2. Connect the discharging jig between negative lead
of the capacitor and check pad CP220.
37-2. Second screw
38-1. Remove two screws (BT3 panhead 1.7 x 3.5
black) from SJ PCB. First screw
37-1. Remove two screws (BT3 panhead 1.7 x 3.5
black) affixing PW PCB. First screw
38-2. Second screw
39. Remove the gray lead wire from PW PCB.
— 38 —
40. Disconnect cable from CN640 on PW PCB.
Caution: Be careful for wire arrangement when you assemble.
41. Disconnect cable from CN210 on SJ PCB.
42-2. Be careful for cable arrangement when you
assemble PCB-K716A- PW unit.
42-3. Enlarged picture of CN630 on PW PCB.
42-1. Remove PW and SJ PCBs.
These two PCBs are provided as a set for spare parts. (PCB-K716A-PW unit)
42-4. Enlarged picture of CN200 on SJ PCB.
Caution: Incomplete insertion of the cable will break IGBT on flash PCB.
— 39 —
43-1. Remove four screws (BT3 panhead 1.7 x 3.5
Black) which affix Flash unit. First screw
44. Remove Flash unit. The 2-pin cable is not included in Flash unit.
43-2. Second screw
43-3. Third screw
45. If this IGBT (Q220) is faulty, flash may light with full emission or light only once on red-eye mode.
46-1. Remove SW PCB pulling with pliers.
43-4. Fourth screw
— 40 —
46-2. After removal of SW PCB.
47-1. Remove LED cover.
Use tweezers. It is stuck with both sided tape.
48. Remove one screw (BT3 flathead 1.4 x 4.0 Black) from Shutter block.
49-1. Remove the hook.
47-2. After removal of LED cover.
47-3. Caution:
When you assemble, be sure that LCD cover and case are level.
49-2. After removal of the hook.
50. Pull click gear off.
— 41 —
51. Remove REC knob, shutter button, and shutter spring
52-1. Remove two screws (BT3 panhead 1.7 x 3.5
Black) which affixing shutter base. First screw
53. Remove shutter base.
54. Shutter block parts
52-2. Second screw
55. Remove one screw (BT3 panhead 1.7 x 3.5 Black) which affixes ST sensor unit.
56. Remove ST sensor unit.
— 42 —
57. Upper case ass'y
61. Disconnect cable from CN451 on SUB PCB.
58. Disconnect gray lead wire from KA PCB.
59. Disconnect cable from CN461 on SUB PCB.
62. Peel the cloth tape.
63. Displace SUB PCB.
60. Disconnect cable from CN460 on SUB PCB.
64-1. Remove LED PCB by unhooking tow hooks.
— 43 —
64-2. LED PCB outer wire
66-3. Third screw
65. Peel cloth tape from buzzer lead wire.
66-1. Remove four screws (BT3 panhead 1.7 x 3 Ni)
which affix KB PCB. First screw
66-4. Fourth screw
67-1. Remove three screws (BT3 panhead 1.7 x 3 Ni)
from KA PCB. First screw
66-2. Second screw
67-2. Second screw
— 44 —
67-3. Third screw
68. Remove KA and KB PCBs. These PCBs are provided as a set as spare part. (PCB-K716A-KEY unit)
69. Remove rubber key.
70. ZOOM knob
— 45 —
EXPLODED VIEW
2
2-1
2-2
2-9
2-3
2-8 2-9
2-4
2-5
S1
X2
(+3.5"FD)
1
S7
2-7
X4
10
3 23 28 13 24 5
S3
32
2-8
2-6
34
33
31
4
22
S4
22
X7
S7
29
16 27 28
35
30
S2
X2
26 25 22
8
S7
X2
S5
X2
7
(2/2)
37
(2/2)
21 15
36
S5
X2
46
S7
40
48
S7
S7
37 (1/2)
S7
49 S5
X2
S6
22
6
51
S5
44
X2
18
19
41
7-1
9
38
S5
X3
47
7
(1/2)
7-2
S3
X3
11 39 12 14 20 17 S2 50 43 45 42
— 46 —
MAIN BODY COMPONENT
N Item Code No. Parts Name Specification Applicable Q Price Code R
N 11001 5687
LENS UNIT
K342105*1 TK(K716)
Common
1EJAN 2
1001 5690
DISPLAY ASSY
K342106*1 TK(K716)
Common
1CWB- 2-1
6614 4530
FRAME/DISPAY
K241200-1
Common
1ACXN 2-2
1001 1751
PANEL/DISPLAY
K441760B-1
Common
1AIBN 2-3
1001 2616
TFT-LCD MODULE
COD18T1035FN
Common
1DEB- 2-4
6614 4540
SPACER/BACK LIGHT
K441763-1
Common
1AAXN 2-5
1001 5719
BL ASSY
K342102*1 TK(K716)
Common
1BVB- 2-6
3851 2113
LAMP/FLUORESCENT
CAS-1.8JS1.8-1
Common
1AWAN 2-7
1001 5721
PCB ASSY/BACK LIGHT
K442091*1 TK(K716)
Common
1BKC- 2-8
6614 4230
TAPE/DOUBLE SIDE
K441774-2
Common
2AAX- 2-9
6614 4240
TAPE/DOUBLE SIDE
K441774-3
Common
2AAXN 3
1002 5309
PCB ASSY/DIGITAL
K442303*1 TK(K716)
Common
1EFAN 4
1001 5727
PCB ASSY/KEY
K342098*1 TK(K716)
Common
1BNBN 5
1001 5723
PCB ASSY/LED
K241383*3 TK(K716)
Common
1CNBN 6
1001 5722
PCB ASSY/SW
K241383*4 TK(K716)
Common
1CMBN 7
1001 5704
PCB ASSY/POWER
K342100*1 TK(K716)
Common
1CZAN 7-1
1000 8870
CABLE/FLAT
K441943-1
Common
1AEX- 7-2
1015 1467
EJECTOR UNIT/CF
55370-0011
Common
1AYXN 8
1001 5696
PCB ASSY/SUB
K342099*1 TK(K716)
US1CO
BN 8
1001 5693
PCB ASSY/SUB
K342099*2 TK(K716)
Except for US
1DBBN 9
1001 5698
BATTERY COVER ASSY
K342097*1 TK(K716)
Common
1AUBN10
1001 5702
FRAME ASSY/BT
K342096*1 TK(K716)
Common
1BAXN11
1001 4270
PLATE/RATING
K442081-1
US1AA
XN11
1001 2557
PLATE/RATING
K442081-2
Except for US
1AAXN12
1000 8856
COVER/FD-A
K441951-1
Common
1ADXN13
1000 8857
COVER/FD-B
K441952-1
Common
1ADXN14
1000 8858
COVER/SENSOR
K441953-1
Common
1ACXN15
1000 8832
GRIP
K441954-1
Common
1ADXN16
1001 1750
PANEL/DISPLAY
K441761A-1
Common
1ACXN17
1000 8843
COVER/IR
K341801-1
Common
1ABXN18
1001 2554
COVER/CF
K341795-1
Common
1AEXN19
1001 2556
LABEL/CF
K441888-2
Common
1AAX-20
6611 0460
PLATE/CASIO
C441170-1
Common
1AGXN21
1001 2559
TAPE/DOUBLE SIDE
K442202-2
Common
1AAX-22
6601 1700
SHEET/INSULATION
K4117-3
Common
5AAXN23
1000 8847
COVER/CN
K241206-2
Common
1AEXN24
1000 8835
CASE/FD
K241308-1
Common
1AFXN25
1000 8836
BUTTON/MODE
K341797-1
Common
1AHXN26
1001 2586
CUSHION
K442203-1
Common
1AAXN27
1000 8828
CASE/UPPER
K140665-1
US1BY
XN27
1001 2583
CASE/UPPER
K140665-2
Except for US
1BYXN28
1000 8852
PIN/STRAP
K441949-1
Common
2AGXN29
1000 8849
KNOB/ZOOM
K341852-1
Common
1AAB-30
6614 5000
RUBBER KEY
K341614-1
Common
1AAX-31
6614 5060
SPRING/CS
K441749-1
Common
1ABX-32
6614 5030
BUTTON/MENU
K341606-1
Common
1AEX
Notes: N
: New registration parts
Q
: Quantity used per unit
R
: Rank
PARTS PRICE LIST
- 47 -
N Item Code No. Parts Name Specification Applicable Q Price Code R
-336614 5040
BUTTON/SET
K341607-1
Common
1AEX-34
6614 5050
BUTTON/CS
K341608-1
Common
1AEX-35
6614 5020
BUTTON/POWER
K341610-1
Common
1AFXN36
1000 8829
CASE/LOWER
K140666-1
Common
1BWXN37
1000 8859
STROBE UNIT
CO-716
Common
1BWAN38
1000 8862
STROBE SENSOR UNIT
CO-716SU
Common
1AXCN39
1000 8851
COVER/LENS
K441958-1
Common
1BAX-40
6613 1210
NUT/TRIPOD
K341059-1
Common
1ACXN41
1000 8839
BASE/SHUTTER
K241297-1
Common
1ACXN42
1000 8837
BUTTON/SHUTTER
K341798-1
Common
1AGXN43
1000 8838
KNOB/REC
K341799-1
Common
1AFXN44
1000 8840
GEAR/CLICK
K341800-1
Common
1AAX-45
6613 9110
SPRING/SHUTTER
K441649-1
Common
1AAXN46
1001 2588
HARNESS/STROBE
K441994-1
Common
1ABX-47
6614 5210
PCB ASSY/BB
K441743-1
Common
1ARXN48
1000 8833
FRAME
K341794-1
Common
1ACXN49
1001 2597
PLATE/INTERCEPTION
K441955-1
Common
1AAXN50
1001 2594
TAPE/DOUBLE SIDE
K442202-1
Common
1AAX-51
6614 4410
COVER/LED
K341643-1
Common
1AAXNS1
1001 2608
SCREW
PS1 1.7X2.5 NI
Common
2AAXNS2
1001 2550
SCREW
BT3 1.7X3.5 BK
Common
3AAXNS3
5861 3530
SCREW
BT3 1.7X3.5NI
Common
4AAX-S4
5112 0884
SCREW
BT3 1.7X3 NI
Common
7AAX
-
S5
1001 2551
SCREW
BT3 1.7X3.5 BK
Common
11
AA
XNS6
1001 2589
SCREW
BT3 1.4X4.0 BK
Common
1AAXNS7
1001 2591
SCREW
BT3 1.7X5.0 NI
Common
10AAX
ACCESSORY
N Item Code No. Parts Name Specification Applicable Q Price Code R
N
1001 2568
CD-ROM
CK716DCA01R
Except for US
1AKX-1015 1424
CF CARD (8 MB)
HB289008C4QV
Except for US
1CZC-3502 2744
CABLE/USB
59204-2301
Common
1BKCN1001 2567
HOLDER/CAP
CH-K716
Common
1AFXN1001 2566
STRAP
ST-K716
Common
1BBXN1001 2565
CASE/SOFT
SC-716
Common
1BJX-1015 1471
CABLE/PC-LINK
LC9F-DOS-K740-L
Except for US
1BUX-1014 8773
CABLE/VIDEO
VC-K723-FC
Common
1ARXN1001 2569
CAP/LENS
K241332-1
Common
1ACC-3816 0266
BATTERY/ALKALINE
LR6PA/2ST
Except for US
2AGX
Notes: N
: New registration parts
Q
: Quantity used per unit
R
: Rank
- 48 -
PRINTED CIRCUIT BOARDS
DIGITAL-PCB (PCB-716D-D)
— 49 —
SUB-PCB (PCB-716D-SUB)
— 50 —
POWER-PCB (PCB-716D-PW)
— 51 —
BACK LIGHT-PCB (PCB-716D-BL)
KEY-A-PCB (PCB-716D-KA)
— 52 —
KEY-B-PCB (PCB-716D-KB)
SWITCH-PCB (PCB-716D-SW)
— 53 —
FLASH-JACK-PCB (PCB-716D-SJ)
CCD-PCB (PCB-716D-CCD) LED-PCB (PCB-716D-LED)
— 54 —
— 55 —
SCHEMATIC DIAGRAMS
DIGITAL-PCB (PCB-K716D-DA)
— 56 —
DIGITAL-PCB (PCB-K716D-DB)
— 57 —
NOTE : Mounted only on the model QV-3000EX/Ir.
SUB-PCB (PCB-K716D-SUB)
— 58 —
POWER-PCB (PCB-K716D-PW)
— 59 —
BACK LIGHT-PCB (PCB-K716D-BL)
— 60 —
FLASH-JACK-PCB (PCB-K716D-SJ)
KEY-A-PCB (PCB-K716D-KA)
— 61 —
KEY-B-PCB (PCB-K716D-KB)
— 62 —
SWITCH-PCB (PCB-K716D-SW)
LED-PCB (PCB-K716D-LED)
— 63 —
CCD-PCB (PCB-K716D-CCD)
— 64 —
Ver. 1 : Change of Page 48.
CASIO TECHNO CO.,LTD.
Overseas Service Division
Nishi-Shinjuku Kimuraya Bldg. 1F 5-25, Nishi-Shinjuku 7-Chome Shinjuku-ku, Tokyo 160-0023, Japan
Loading...