MA1709-EC
© 2017 CASIO COMPUTER CO., LTD.
Operation Guide 5519
Contents
Basic Operations
Watch Face Items
Navigating Between Modes
Mode Overview
Using the Crown
Hands and the Day Indicator Movement
Solar Charging
Using Mobile Link with a Mobile
Phone
Getting Ready
A Installing applications
B Configuring Bluetooth settings
C Pairing the watch with a phone
Auto Time Adjustment
Configuring World Time Settings
Viewing Stopwatch Data
Watch Settings
Setting the Time and Date
Configuring Dual Time Settings
Swapping Your Current Location Time and
Dual Time Settings
Stopwatch
Measuring Elapsed Time
Taking a Split Time Reading
Alarms
Configuring Alarm Settings
Turning the Alarm On or Off
Stopping an Alarm
Hand Alignment Adjustment
Correcting Hand Alignment
Moving To Another Time Zone
Setting the Alarm
Correcting Hand Alignment
Checking for Mail
Phone Finder
Configuring Watch Settings
Returning the Watch to Its Factory Default
Settings
Changing the Home City Summer Time Setting
Checking the Watch Charge Level
Connection
Connecting with a Phone
Disconnecting from a Phone
Entering the Watch Airplane Mode
Unpairing
After Purchasing Another Phone
Other Information
Summer Time Switching
Supported Phone Models
Specifications
Mobile Link Precautions
Copyrights and Registered Copyrights
Troubleshooting
1
30
①
②
③
④⑤
⑥
⑦
⑧
⑨
⑩
A
A
A
C
Bluetooth connection
Alarm Mode Stopwatch Mode
Calendar Mode
(Approximately
1.5 seconds)
Any button
③④ ⑤
①②
Airplane Mode
(Hold down about
4 seconds.)
③④ ⑤
②
①
Split/Reset
Start/Stop
Airplane Mode
(Hold down about
4 seconds.)
③④ ⑤
②
①
Enabling/Disabling
the Alarm
Airplane Mode
(Hold down about
4 seconds.)
Operation Guide 5519
Basic Operations
This section provides an overview of the watch
and its operations.
Note
●
The illustrations included in this
operation guide have been created
to facilitate explanation. An
illustration may differ somewhat
from the item it represents.
Watch Face Items
Navigating Between Modes
Your watch has the modes shown below.
Stopwatch Mode
●
In this mode, the main hour and minute hands
indicate the current time in your current
location (Home City), while the dial hour and
minute hands show elapsed time as
measured by the stopwatch.
A
Stopwatch minutes
B
Stopwatch seconds
C
Stopwatch hours
D
Stopwatch 24-hour hand
The A-side of the dial indicates hours 0
through 12, while the P-side indicates hours
12 through 24.
A
e mark
When the watch is connected with a phone,
the second hand points to e.
B
R mark
When the watch is standing by for connection
with a phone, the second hand points to “R”.
C
Day of week
The mode
hand points to the current day of the
week.
D
ON mark
When the watch is in the Alarm Mode and the
alarm is enabled, the second hand points to
“ON”.
E
OFF mark
When the watch is in the Alarm Mode and the
alarm is disabled, the second hand points to
“OFF”.
F
AL mark
When the watch is in the Alarm Mode, the
mode hand points to “AL”.
G
l mark
The mode hand will point to “l” when your
phone has new mail.
H
¢ mark
The mode hand will point to “¢” when your
phone has no new mail.
I
Speedometer
When the watch is in the Stopwatch Mode, the
mode hand will
point to a speed value after an
elapsed time measurement is complete.
Requires specification of the distance
*
traveled and a distance unit with CASIO
WATCH+.
Viewing Speed Data
l
J
Airplane Mode
When the watch is in the Airplane Mode, the
mode hand points to h.
E
Average speed (unit per hour)
If you use CASIO WATCH+ to specify the
travel distance and unit, the mode hand will
indicate your average speed. The initial
Use (A) to navigate between modes. Hold
down (A) for about two seconds to enter the
default setting of the travel distance is 1.
Viewing Speed Data
l
Calendar Mode. To connect with a phone,
Alarm Mode
hold down (C) for about 1.5 seconds.
●
In this mode, the main hour and minute hands
indicate the current time in your current
Mode Overview
Calendar Mode
●
location (Home City), while the dial hour and
minute hands show the alarm time setting.
In this mode, the main hour and minute hands
indicate the current time in your current
location (Home City), while the dial hour and
minute hands show
another time (Dual Time).
A
Alarm minute
B
Alarm enable/disable
The second hand will point to “ON” while the
alarm is turned on, and to “OFF” while it is
turned off.
A
Dual Time minute
B
Current second in your current location
(Home City)
C
Dual Time hour
D
Dual Time 24-hour hand
C
Alarm hour
D
Alarm 24-hour hand
The A-side of the dial indicates an a.m. time,
while the P-side indicates a p.m. time.
E
Mode
The A-side of the dial indicates an a.m. time,
*
while the P-side indicates a p.m. time.
E
Current day of the week in your current
location (Home City)
2
Loosen
Crown
Normal timekeeping
Screw in
Day indicator
Mode hand
NOYES
Operation Guide 5519
Using the Crown
The watch’s crown is a screw-in (screw lock)
type. To use
it towards you (leftwards) to loosen it.
the crown, you first need to rotate
●
Fast Forward/Fast Reverse
After pulling out the crown, rotating it quickly
succession in
in
either direction will cause the
hands to move forward or back at high speed.
While the hands are moving forward at high
speed, quickly rotating the crown in
succession again will increase the speed even
further.
●
Stopping Fast Forward/Fast Reverse
Rotate the crown in the direction opposite that
of the ongoing operation or press any button.
Solar Charging
This watch runs on power supplied from a
rechargeable (secondary) battery that is
charged by a solar panel. The solar panel is
integrated into the face of the watch, and
power is generated whenever the face is
exposed to light.
Charging the Watch
●
When you are not wearing the watch, put it in
a location where it is exposed to bright light.
●
Pulling Out and Pushing In the Crown
Before performing a crown operation, you
to pull
need
it out to the first or second click as
shown in the figures below. Do not pull the
crown with too much force.
First click
Second click
Important!
●
To prevent loss of water resistance
and/or damage due to impact, be
sure to screw
it away from you as you push it in.
●
When pushing the crown back in,
take care not to apply too much
force.
the crown in by rotating
Note
●
If you do not perform any operation
for about two minutes after pulling
out the crown, crown operations will
automatically become disabled. If
that happens, push the crown back
in and then pull it out again.
Hands and the Day Indicator Movement
●
Mode Hand and Day Indicator
Movement
Changing the day setting of the watch will also
cause the mode hand to move.
●
Day
●
can take
It
to three minutes for the day indicator to
change after timekeeping reaches
midnight. The mode hand moves as the day
indicator changes.
●
The day may
the watch’s crown is pulled out.
anywhere from about 90 seconds
not be indicated correctly while
While you are wearing the watch, make sure
that its face (solar panel) is not blocked from
the light by the sleeve of your clothing. Power
generation efficiency is reduced even when
the face of the watch is blocked only partially.
Important!
●
Depending on light intensity and
local conditions, the watch may
become hot to the touch when
exposed to light for charging. Take
care to avoid burn injury after
charging. Also, avoid charging the
watch under high-temperature
conditions like the ones described
below.
ー
On the dashboard of a vehicle
parked in the sun
ー
Near an incandescent
other source of heat
ー
Under direct sunlight or in other
hot areas for long periods
Remaining Charge and Dead Battery
●
The charge level is indicated by watch hand
movement. Functions become disabled as
battery power goes low.
light bulb or
Important!
●
Should battery go low or go dead,
expose the face
as soon as possible.
(solar panel) to light
3
30
Second hand
1
Bluetooth mark
Operation Guide 5519
Note
●
Exposing the watch
the battery goes dead will cause the
second hand to revolve
counterclockwise until it stops at
second 57. This indicates charging
has started.
Low Battery Power
The second hand jumps at two-second
intervals.
Dead Battery
All hands and the day indicator are stopped.
Charging Time Guidelines
●
The table below shows guidelines for
approximate charging times.
Required Charging Time for 1-day Use
Light Intensity Approximate Charging Time
p
Low
p
A
B
C
D
Approximate Charging Time
Charge Level1Charge Level
A
B
C
D
High
Time Required to Achieve Next Charge
Level
Light Intensity
High
Low
Charge Level 1 :
Time from dead battery until hand movement
starts
Charge Level 2 :
Time from hand movement starts until a full
charge
face to light after
8 minutes
30 minutes
48 minutes
8 hours
2
3 hours 37 hours
9 hours 138 hours
13 hours 223 hours
153 hours -
Light Intensity
A
Sunny day, outdoors (50,000 lux)
B
Sunny day, near a window (10,000 lux)
C
Overcast day, near a window (5,000 lux)
D
Indoor fluorescent lighting (500 lux)
Note
●
Actual charging time
local charging environment.
Power Saving
●
Leaving the watch in a dark location for about
one hour between the hours of 10 p.m. and 6
a.m. will cause the second hand to stop, and
the watch will enter Level 1 power saving. If
the watch is left in this condition for six or
seven days, all hands (except for the mode
will stop
hand)
enter Level 2 power saving.
Level 1 :
Second hand stops to save power.
Level 2 :
The following operations are stopped to save
power:
indicator), Bluetooth connection, and alarm
alerts.
Recovering from Power Saving Operation
Press any button or place the watch in a welllit area to recover from power saving.
at 12 o’clock and the watch will
all hand
movement (excluding the day
depends on the
Using Mobile Link with
a Mobile Phone
While there is a Bluetooth connection
between the watch
setting is adjusted automatically in
accordance with the phone’s time setting.
Note
●
This function is available only while
CASIO WATCH+ is running on the
phone.
●
This section describes watch and
phone operations.
X : Watch operation
Y : Phone operation
and phone, the watch time
Getting Ready
A Installing applications
To use the watch with a phone, first tap one of the
links below and install the “CASIO WATCH+” app
on the phone.
●
iOS (iPhone) Users
https://itunes.apple.com/us/app/
id760165998?ls=1&mt=8
●
AndroidTM
https://play.google.com/store/apps/details?
id=com.casio.watchplus
B
Configuring Bluetooth settings
Enable the phone’s Bluetooth.
Note
●
C Pairing the watch with a phone
Before you can use the watch in combination
with a phone,
the watch is paired with a phone, you normally
do not need to pair them again.
1.
Move the phone
(within one meter of) the watch.
2.
Y On the Home Screen, tap the “CASIO
WATCH+” icon.
3.
Y
4.
Y
Tap “EQB-501”.
5.
Y Perform operations as instructed by the
app.
●
●
(GALAXY, etc.) Users
For details about setting
procedures, see your phone
documentation.
you first need to pair them. Once
to be paired with close to
Tap “EDIFICE”.
If a pairing prompt message appears,
perform the operation shown on the
phone screen.
When pairing starts, the second hand
will move to 12 o’clock or to the
mark. When pairing is complete, the
second hand will move to e.
“R”
4
Note
12:30
●
You also need to perform the above
pairing procedure after switching to
a different phone or whenever
connecting to any
phone for the first
time. In such cases you do not need
to unpair with the phone you have
been previously paired with.
Auto Time Adjustment
Operation Guide 5519
●
Summer Time
Once the watch is connected with a phone and
its time is adjusted with the phone time, its
Home City time and World Time will
automatically switch between standard time
and summer time as required, even if the
is
watch
Summer Time Switching
l
●
Changing the time setting manually with a
longer connected with the phone.
no
watch operation will cancel auto standard
time/summer time switching.
●
A CASIO WATCH+ screen shows
information about summer time periods.
2.
X
Hold down the (C) button for about 1.5
seconds.
●
The second hand
will move to “R”. Keep
(C) depressed until the second hand
starts moving again and then stop at
“R”.
●
The second hand
will move to e when a
connection is established between the
watch and phone.
The watch can be set to adjust its time setting
automatically each day
in accordance with the
phone time.
●
Using Auto Adjust
Your watch adjusts its time setting four times
a day. It performs the adjustment operation
automatically as you go about your daily life,
without any operation required by you.
Important!
●
The watch may not be able to
perform auto time setting
adjustment under the conditions
described below.
ー
While it is too far away from its
paired phone
ー
When communication is not
possible due to
radio interference,
etc.
ー
While the phone is updating its
system
Note
●
If there is
with CASIO WATCH+, its time will
also be adjusted automatically.
●
The watch will connect with the
phone and perform auto time
adjustment at around 12:30 a.m.,
6:30 a.m., 12:30 p.m. and 6:30 p.m.
The connection is automatically
terminated after auto time
adjustment is complete.
a World Time City specified
●
Triggering Immediate Time Adjustment
The watch will adjust its time setting to that of
the phone immediately after they are
connected with each other. Whenever you
want
to
the watch’s time setting perform
adjust
the procedure below to connect with a phone.
1.
Y On the Home Screen, tap the “CASIO
WATCH+” icon.
2.
Press (C).
X
This causes the second hand to move to
“R”.
The second
hand will move to e when
a connection is established between the
watch and phone, and the time setting of
the watch will adjust to the phone’s time
setting.
●
The connection is terminated
automatically after time adjustment is
complete.
●
Disabling Auto Time Correction
To stop the watch from automatically
connecting of your phone to adjust its time
settings, perform the operation below to
disable auto time correction.
1.
Y On the Home Screen, tap the “CASIO
WATCH+
” icon.
3.
Y Tap in the following sequence: f n
“Watch settings”.
4.
Y Tap “Time adjustment”.
5.
Y
Perform the operation shown on the
phone screen.
Configuring World Time Settings
Specifying a World Time City with CASIO
WATCH+ causes the city’s time to be
indicated by the
Watch settings can be configured for auto
summer time switching for the World Time
City.
Note
●
CASIO WATCH+ World Time lets
you select from among
approximately 300 cities as the
World Time City.
small hour and minute hands.
5
30
World Time hour (24-hour)
World Time hour and minute
After swappingBefore swapping
World Time
World Time
Home Time
Home Time
Operation Guide 5519
●
Selecting a World Time City
1.
Y Tap the “CASIO WATCH+” icon.
2.
Hold down the (C) button for about 1.5
X
seconds.
●
The second hand
will move to “R”. Keep
(C) depressed until the second hand
starts moving again and then stop at
“R”.
●
The second hand
will move to e when a
connection is established between the
watch and phone.
3.
Y Tap “World time”.
4.
Y Specify a World
Time City by inputting a
city name or by tapping its location on the
on-screen map.
5.
Y Perform the operation shown on the
phone screen. The
World Time setting will
be reflected on the watch.
The dial hour and minute hands, and the
small 24-hour hand indicate the current
time in the selected city and time zone.
●
You can determine whether a World
Time is a.m. or p.m. by checking the
position of the small 24-hour hand.
●
Configuring the Summer Time Setting
1.
Y Tap the “CASIO WATCH+” icon.
2.
Hold down the (C) button for about 1.5
X
seconds.
●
The second hand
will move to “R”. Keep
(C) depressed until the second hand
starts moving again and then stop at
“R”.
●
The second hand
will move to e when a
connection is established between the
watch and phone.
3.
Y Tap “World time”.
4.
Y Specify a World
Time City by inputting a
city name or by tapping its location on the
on-screen map.
If your currently specified World Time City
observes summer time, the summer time
period will appear on the display.
5.
Y Select the summer time switching
method you want to use.
●
”
“Auto
The watch switches between standard
time and summer time automatically.
●
“OFF”
The watch always indicates standard
time.
●
“ON”
The watch always indicates summer
time.
6.
Y Perform the operation shown on the
phone screen.
Note
●
When “Auto” is selected for
standard/summer time switching,
the watch will switch between
standard time and summer time
automatically. Do not need to
change the time
changes between summer time and
standard time. Even if you are in an
area that does not observe summer
time, you can leave the watch’s
summertime setting as “Auto”.
●
Changing the time setting manually
with a watch operation will cancel
auto standard time/summer time
switching.
●
A CASIO WATCH+ screen shows
information about summer time
periods.
●
Swapping Your World Time and Home
Time
1.
Y Tap the
2.
Hold down the (C) button for about 1.5
X
seconds.
●
The second hand
(C) depressed until the second hand
starts moving again and then stop at
“R”.
●
The second hand
connection is established between the
watch and phone.
setting manually for
“CASIO WATCH+” icon.
will move to “R”. Keep
will move to e when a
3.
Y Tap “World time”.
4.
Y
Tap k.
5.
Y Perform the operation shown on the
phone screen to swap your Home Time
with your World Time.
6
30
30
30
Speed
Minutes
Hours
24-hour
Seconds
B
D
D
B
Stop
Start
Operation Guide 5519
Note
●
Auto time adjustment is not
performed for 24 hours after
swapping of the Home Time and
World Time.
Viewing Stopwatch Data
This section explains how to send lap times
and split times (up to 100 records) stored in
watch memory, as well as the best lap,
average speed, and other data to your phone
for viewing with CASIO WATCH+.
●
Sending Stopwatch Data to a Phone
Use the procedure below to send data from
the watch to a phone.
1.
Y Tap the “CASIO WATCH+
2.
Hold down the (C) button for about 1.5
X
seconds.
●
The second hand
(C) depressed until the second hand
starts moving again and then stop at
“R”.
●
The second hand
connection is established between the
watch and phone.
” icon.
will move to “R”. Keep
will move to e when a
●
Checking a Lap Time
Use CASIO WATCH+ to check the data you
sent to the phone.
1.
Y Tap the
2.
Y
Tap the CASIO WATCH+ j icon.
3.
Y
Box”
4.
Y On the list of stopwatch data, tap the
“CASIO WATCH+” icon.
Tap in the following sequence: “Data
n “EQB-501”.
item you want to look up.
This displays the details of the tapped
stopwatch data.
Note
●
Tapping “Edit” displays
you can use to change the data item
title and to delete lap time data.
●
Viewing Speed Data
Use the procedure below to configure the
watch to indicate speeds.
1.
Y Tap the
2.
X Hold down the (C) button for about 1.5
“CASIO WATCH+” icon.
seconds.
●
The second hand
(C) depressed until the second hand
starts moving again and then stop at
“R”.
●
The second hand
connection is established between the
watch and phone.
a screen that
will move to “R”. Keep
will move to e when a
Before a race
Configure course length and speed unit
settings.
Viewing Speed Data
l
During a race
Measure lap times.
1.
X Hold down (A) for about 2 seconds.
This will cause the watch to enter the
Calendar Mode.
2.
X Press (A) once.
This will cause the watch to enter the
Stopwatch Mode.
3.
X Use the operations below to measure
elapsed time.
3.
Y Tap in the following sequence: f n
“Data Box”.
4.
Tap “Data transfer”.
Y
This displays a list of stopwatch data on
the phone.
●
Tapping a stopwatch
data item displays
its details.
3.
Y Tap “Stopwatch”.
4.
Y Use the screen that appears to specify
the distance and distance unit.
●
Example: Recording a Race Lap Time
This section explains how to record lap times
while watching a race, and then review the
results using CASIO WATCH+.
Pressing (D) at the end of each lap will
record the lap time.
●
Lap times are recorded in units of
1/1000 seconds.
4.
X Press (D) to reset the elapsed time to
zero.
5.
X Press
(A)
to return to the Calendar
twice
Mode.
After a race
Check the measured lap times.
Sending Stopwatch Data to a Phone
l
Checking a Lap Time
l
7
After disconnectionConnected
Operation Guide 5519
Setting the Alarm
1.
Y Tap the “CASIO WATCH+” icon.
2.
Hold down the (C) button for about 1.5
X
seconds.
●
The second hand
(C) depressed until the second hand
starts moving again and then stop at
“R”.
●
The second hand
connection is established between the
watch and phone.
3.
Y Tap “Alarm”.
4.
Y
Perform the operation shown on the
phone screen.
will move to “R”. Keep
will move to e when a
Checking for Mail
You can use the watch to check if you have
new mail on your phone.
Getting ready
Register your mail address account with
CASIO WATCH+.
1.
Y Tap the “CASIO WATCH+” icon.
2.
X
Hold down the (C) button for about 1.5
seconds.
●
The second hand
(C) depressed until the second hand
starts moving again and then stop at
“R”.
●
The second hand
connection is established between the
watch and phone.
will move to “R”. Keep
will move to e when a
Phone Finder
You can use phone finder to trigger a tone on
the phone to make it easy to find. The tone is
forced to sound even if the phone is in the
manner mode.
Important!
●
Do not use this function in areas
where phone call tones are
restricted.
●
The tone sounds at a high volume.
Do not use this function when
listening to phone output over
earphones.
1.
X If the watch is connected with a phone,
press any button to terminate the
connection.
Correcting Hand Alignment
If the hands are out of alignment even though
auto time adjustment
CASIO WATCH+ to adjust them.
1.
Y Tap the “CASIO WATCH+” icon.
2.
Hold down the (C) button for about 1.5
X
seconds.
●
The second hand
(C) depressed until the second hand
starts moving again and then stop at
“R”.
●
The second hand
connection is established between the
watch and phone.
3.
Y Tap in the following sequence: f n
“Watch settings”.
4.
Y Tap “Adjusting home positions”.
5.
Y
Perform the operation shown on the
phone screen.
is being performed, use
will move to “R”. Keep
will move to e when a
3.
Y Tap in the following sequence: f n
“Alert settings”.
4.
Y Perform the operation shown on the
phone screen.
Note
●
The types of accounts listed below
are supported for registration.
@gmail.com, @yahoo.com,
@yahoo.co.jp, @icloud.com,
@aol.jp, @aol.com, @aim.com,
@i.softbank.jp, @outlook.jp,
@outlook.com
●
Checking for Mail
1.
X If the watch is connected with a phone,
press (D). If the watch is not connected
with a phone,
seconds.
The mode hand will move to l or ¢.
l: You’ve got new mail.
¢: No new mail.
●
If you’ve got new mail
Use your phone to view your mail.
hold down (C) for about 1.5
2.
X Hold down (A) for about two seconds.
This will cause the watch to enter the
Calendar Mode.
3.
X Hold down (D) for about 0.5 seconds
until the second hand points to R.
The second hand will move to e when a
connection is established between the
watch and phone, and then the phone’s
ringtone will sound.
●
It will take a few seconds before the
phone tone sounds.
4.
X Press any button to stop the tone.
●
You
can press
the phone tone only during the first 30
seconds after it starts to sound.
any watch button to stop
8
MinutesHours
Mode hand
Crown
Operation Guide 5519
Configuring Watch Settings
You can use CASIO WATCH+ to specify the
amount of time
until the Bluetooth connection
is automatically terminated, and to configure
other settings.
1.
Y Tap the “CASIO WATCH+” icon.
2.
Hold down the (C) button for about 1.5
X
seconds.
●
The second hand
will move to “R”. Keep
(C) depressed until the second hand
starts moving again and then stop at
“R”.
●
The second hand
will move to e when a
connection is established between the
watch and phone.
3.
Y Tap in the following sequence: f n
“Watch settings”.
4.
Y Select the setting you want to change
and then perform the operation shown on
the phone screen.
Returning the Watch to Its Factory Default Settings
This section explains how to use CASIO
WATCH+ to return the watch settings below
to their initial factory defaults.
●
Time adjustment
●
World time
●
Alarm
●
Stopwatch
●
Connection time
1.
X Pull out the crown to the second click.
2.
X Hold down (C) for about 5 seconds.
This will cause the second hand to
perform one revolution and return the
applicable settings to their factory
defaults.
Changing the Home City Summer Time Setting
1.
Y On the Home Screen, tap the “CASIO
WATCH+” icon.
2.
Hold down the (C) button for about 1.5
X
seconds.
●
The second hand
(C) depressed until the second hand
starts moving again and then stop at
“R”.
●
The second hand
connection is established between the
watch and phone.
3.
Y Tap in the following sequence: f n
“Watch settings”.
4.
Y Tap
“Summer time setting
5.
Y
Select the summer time switching
method you want to use.
●
“Auto”
The watch switches between standard
time and summer time automatically.
●
“OFF”
The watch always indicates standard
time.
●
“ON”
The watch always indicates summer
time.
6.
Y Perform the operation shown on the
phone screen.
will move to “R”. Keep
will move to e when a
”.
Checking the Watch Charge Level
Use the procedure below to check the current
charge level with CASIO WATCH+.
1.
Y On the Home Screen, tap the “CASIO
WATCH+” icon.
2.
X
Hold down the (C) button for about 1.5
seconds.
●
The second hand
will move to “R”. Keep
(C) depressed until the second hand
starts moving again and then stop at
“R”.
●
The second hand
will move to e when a
connection is established between the
watch and phone.
3.
Y Use CASIO WATCH+ to check the
charge level.
Connection
Connecting with a Phone
This section explains how to establish a
Bluetooth connection between
paired with the watch.
●
If the watch
is not paired with the phone you
want to connect with, perform the procedure
under “C Pairing the watch with a phone” to
pair them.
1.
Move the phone
close to (within one meter
of) the watch.
2.
X While the second
e, hold down the (C) button for about 1.5
seconds.
●
second
The
hand
(C) depressed until the second hand
starts moving again and then stop at
“R”.
●
The second hand
connection is established between the
watch and phone.
a phone that is
hand is not pointing to
will move to “R”. Keep
will move to e when a
9
After disconnectionConnected
30
Airplane mark
After disconnectionConnected
Crown
Operation Guide 5519
Important!
●
If you have problems establishing a
connection, it could mean that
CASIO WATCH+ is not running on
the phone. On the phone’s home
screen, tap the “CASIO WATCH+”
icon. After the app starts up, hold
down the watch’s (C) button for
about 1.5 seconds.
Note
●
The connection will be terminated if
you do not perform any operation on
the watch or phone for a fixed
amount of time.
To specify the connection limit time,
perform the following operation with:
use CASIO WATCH+ to select
“Watch settings” n “Connection
time”, and then specify a setting of 3
minutes, 5 minutes, or 10 minutes.
Disconnecting from a Phone
Pressing any button terminates the Bluetooth
connection and returns
normal operation.
the second hand to its
Entering the Watch Airplane Mode
Use the Airplane Mode to disable Bluetooth
radio wave emissions.
Put the watch into its Airplane Mode when in
a hospital, in an aircraft, or anywhere else
where radio wave emissions are restricted.
When you need to connect with a phone
again, exit the watch Airplane Mode.
Important!
●
The functions below are disabled
while the watch is in the Airplane
Mode.
ー
Auto adjust
ー
Checking for new mail
ー
Phone finder
ー
Bluetooth connection
1.
X If the watch is connected with a phone,
press any button to terminate the
connection.
2.
X Hold down (A) for about four seconds.
The watch will enter the Airplane Mode
and the mode hand will move to the
Airplane Mode mark.
●
To exit the watch Airplane Mode, hold
down (A) for about four seconds.
Unpairing
1.
X If the watch is connected with a phone,
press any button to terminate the
connection.
2.
Y On the Home Screen, tap the “CASIO
WATCH+” icon.
3.
Tap the CASIO WATCH+ j icon.
Y
4.
Y In the “Previously registered watch” list,
tap the watch you want to unpair.
5.
Y
Tap “Delete pairing registration”.
6.
Y
Perform the operation shown on the
phone screen.
Note
●
If you are
with a phone after unpairing them,
use the procedure below to delete
pairing information from the watch
and then perform the pairing
operation again.
A X Pull out the crown to the second
click.
unable to re-pair the watch
B X Hold down (D) for about 5
seconds.
This causes the second hand to
perform
one revolution
and deletes the
pairing information.
C X Push the crown back in.
After Purchasing Another Phone
You need to perform the pairing operation
whenever you want to establish a Bluetooth
connection with a phone for the first time.
Pairing the Watch with a phone
l
10
Calendar Mode
MinutesHours
Crown
8
9
10
3
4
2
57
11
1
6
12
DayMonth
80
90 30
40
20
50
70
10
60
00
Year (10’s digit)
8
9
3
4
2
57
1
6
0
Year (one’s digit)
Dual Time 24-hour
Dual Time
＋
−
Dual Time 24-hour hand
Dual Time minute hand
Dual Time hour hand
Crown
After swappingBefore swapping
Dual Time
Dual Time
Current location time
Current location time
Operation Guide 5519
Watch Settings
Use the procedure below to configure current
location time and Dual Time settings
manually.
Getting ready
Perform this procedure in the Calendar Mode.
Use (A) to navigate to the Calendar Mode.
Navigating Between Modes
l
Setting the Time and Date
While the watch is connected to a phone, it will
automatically adjust its day and time settings
to those of the phone. If the watch is not
connected to a phone, use the procedure
below to adjust its day and time settings.
1.
Pull out the crown to the second click.
This causes the second hand to move to
12 o’clock and enables the hour and
minute setting operation.
4.
Press (B) to change the month.
5.
Rotate the crown to change the day.
6.
Press (A).
This enables the year 10’s digit setting
operation.
7.
Rotate the crown to change the year 10’s
digit.
8.
Press (A).
This enables the year one’s digit setting
operation.
9.
Rotate the crown
to change the year one’s
digit.
Configuring Dual Time Settings
Dual Time lets you keep track of the current
time in another time zone in addition your
current location time.
Pull out the crown to the first click.
1.
This causes the second hand to move to
12 o’clock.
Rotate the crown
2.
setting.
●
You can set
increments.
Push the crown back in.
3.
to change the Dual Time
the Dual Time in 15-minute
2.
Rotate the crown to adjust the hour and
minute settings.
●
The Dual Time setting is also adjusted
in accordance with the current time
setting. Crown operation is disabled
while the Dual Time setting is being
adjusted.
3.
Press (A).
This enables the month and day setting
operation.
10.
On a time signal at the top of a minute,
push the crown back in.
Note
●
The day of the week is set
automatically
year, month, and day settings.
accordance
in
with the
Swapping Your Current
Location Time and
Dual Time
Settings
You can swap the time in your current location
with the Dual Time by holding down (B) for
about three seconds.
Note
●
If you are using the small hour and
minute hands for
time in your current location will be
swapped with Dual Time. Dates are
not swapped.
Dual Time, only the
11
30
Stopwatch Mode
24-hour
Speed
Minutes
Hours
Seconds
B
B
B
D
Stop
Resume
Stop
Start
30
Speed
Minutes
Hours
24-hour
Seconds
B
D
B
Stop
Split*
Start
Alarm Mode
Alarm on
Crown
Minutes
Hours
24-hour
OFFON
Operation Guide 5519
Stopwatch
The stopwatch can measure elapsed time up
to 23 hours, 59 minutes, 59 seconds.
It can also measure split times.
Getting ready
Perform this procedure in the Stopwatch
Mode. Use (A) to navigate to the Stopwatch
Mode.
Navigating Between Modes
l
Measuring Elapsed Time
Taking a Split Time Reading
1.
Use the operations below to measure
elapsed time.
* Each press of (D) causes the elapsed
time up to that point (split time) to be
indicated for 10 seconds.
2.
Press (D) to reset the elapsed time to all
zeroes.
3.
Press (A) twice to return to the Calendar
Mode.
Alarms
The watch will beep when the alarm time is
reached.
Getting ready
Perform this procedure in the Alarm Mode.
Use (A) to navigate to the Alarm Mode.
Navigating Between Modes
l
Configuring Alarm Settings
1.
Pull out the crown to the first click.
This turns on the alarm.
1.
Use the operations below to measure
elapsed time.
2.
Press (D) to reset the elapsed time to all
zeroes.
3.
Press (A) twice to return to the Calendar
Mode.
Note
●
The watch has enough memory to
store up to 100 split time records.
You can use CASIO WATCH+ to
view split time records.
2.
Rotate the crown
to change the alarm time
setting.
3.
Push the crown back in.
4.
Press (A) once to return to the Calendar
Mode.
Turning the Alarm On or Off
Each press of (B) toggles the alarm between
on and off.
Stopping an Alarm
While the alarm is sounding, press any button
to stop it.
12
Small 24-hour hand
Small minute
hand
Small hour hand
Mode Hand
24-hour hand
Minute hand
Hour hand
Second Hand
1
Day indicator
Destination time Current time
Airplane mark
After swappingBefore swapping
Destination time
Destination time
Operation Guide 5519
Hand Alignment
Adjustment
Strong magnetism or impact can cause the
time indicated by the hands and the day
indicator to go out of alignment. If this
happens, correct hand alignment.
Correcting Hand Alignment
1.
Pull out the crown to the first click.
2.
Hold down (D) for about five seconds.
This enables adjustment of small hour
hand, small minute hand, and small 24hour hand alignment.
3.
Rotate the crown to align the small hour
hand, small minute hand, and small 24hour hand with 12 o’clock.
4.
Press (A).
This enables adjustment of mode hand
alignment.
7.
Rotate the crown to align the hour and
minute hands with 12 o’clock.
8.
Press (A).
This enables adjustment of second hand
alignment.
9.
Rotate the crown to align the second hand
with 12 o’clock.
10.
Press (A).
This enables adjustment of day indicator
alignment.
11.
Rotate the crown to align “1”
of the day indicator.
12.
Push the crown back in.
in the center
Moving To Another
Time Zone
Use the procedure below to easily change day
and
time settings
location.
●
Before Boarding
Configure the World Time (Dual Time) to the
current time at your destination.
Configuring World Time Settings
l
Configuring Dual Time Settings
l
●
Prior to Takeoff
Enter the watch’s Airplane Mode when
instructed to do so by airline personnel.
of the watch to a destination
5.
Rotate the crown to align the mode hand
with 0.
6.
Press (A).
This enables adjustment of hour hand,
minute hand, and 24-hour hand
alignment.
Entering the Watch Airplane Mode
l
●
After Arriving
1.
Swap the origin time zone time with the
destination time zone time.
Swapping Your Current Location Time
l
and Dual Time Settings
2.
Exit the Airplane Mode.
Entering the Watch Airplane Mode
l
13
Operation Guide 5519
Other Information
This section provides non-operational
information you also need to know. Refer to
this information as required.
Summer Time Switching
●
Connecting with a Phone to Switch
After the watch is connected with a phone,
summer time
World Time is performed in accordance with
the CASIO WATCH+ setting (Auto/ON/OFF)
as described below.
Auto :
After the watch is connected with a phone,
summer time is displayed for the current
location time or World Time when it is within
the summer time period. Otherwise standard
time is displayed.
ON :
The watch always displays summer time.
OFF :
The watch always displays standard time.
●
Auto Summer Time Switching
When the watch is connected to a phone, it is
sent summer time period information for your
Home City. If there is a World Time City
specified with CASIO WATCH+, information
for that city will also be sent. If the CASIO
WATCH+ summer time setting is
watch will automatically keep track of the
summer
switching automatically, even if it is not
connected with the phone.
Supported Phone Models
For information about supported phone
models, visit the CASIO Website.
http://world.casio.com/os_mobile/wat/
switching of Home City time and
“Auto”, the
time period and perform summer time
Specifications
Accuracy at normal temperature :
±15 seconds a month
Timekeeping :
Hour and minute (move at 10-second
intervals), second, day (2000 to 2099 full
auto calendar), day of the week
Dual Time :
Hour,
minute,
24-hour hand, swapping with
Home City time
Stopwatch :
Measuring unit: 1 second
Measuring capacity: 23:59'59" (24 hours)
Measurement functions: Elapsed time, split
times
Speed Display: 0 to 300 units/hour
Alarm :
Setting Units: Hour, minute
Beeper: 10 seconds
Mobile Link :
Auto Time Correction
Time setting adjusted automatically at
preset time.
Mail checking
Check for incoming mail from the watch
Phone finder
Watch operation sounds the alert sound
of the mobile phone.
Auto Summer Time Switching
Automatic switching between standard
time and summer time.
Stopwatch data transfer
Transfers up to 100 1/1000-second lap/
split data records to phone for viewing.
Hand position correction
Data Communication Specifications
Bluetooth
Frequency Band: 2400MHz-2480MHz
Maximum Transmission: 0 dBm (1 mW)
Communication range: Up to 2 meters
(depends on environment)
Other :
Power Saving, Low Battery Alert, Airplane
Mode (disables data communication)
®
Mobile Link Precautions
●
Legal Precautions
●
This watch complies with or has received
approval under the radio laws of various
countries and geographical areas. Using
this watch in an area where it does not
comply with or has not received approval
under applicable radio laws may be a
criminal offense.
Website.
http://world.casio.com/ce/BLE/
●
Use of this watch inside of aircraft is
restricted under the aviation laws of each
country. Be
airline personnel.
●
Precautions when using Mobile Link
●
When using this watch in combination with
a phone, keep the watch and phone close
to each other. A range of two meters is
recommended as a guideline, but the local
environment (walls, furniture, etc.), the
structure of
require a much closer range.
●
This watch
(electrical devices, audio-visual equipment,
office equipment, etc.) In particular, it can be
affected by operation of a microwave oven.
The watch may not be able to communicate
normally with a phone if a microwave oven
is operating nearby. Conversely, this watch
may cause noise in radio reception and the
video image of a TV.
●
Bluetooth of this watch uses the same
frequency band (2.4 GHz) as wireless LAN
devices, and use of such devices in close
proximity of this watch may result in radio
interference, slower
and noise for the watch and the wireless
LAN device, or even communication failure.
For details, visit the CASIO
sure to follow the instructions of
a building, and other factors may
can be affected by other devices
communication speeds
Power Supply :
Solar panel and one rechargeable battery
Approximate Battery Life :
Approximately 8 months
Conditions
Mobile Link: 4 times (40 seconds)/day
Alarm: Once (10 seconds)/day
Power Saving: 6 hours/day
14
After disconnectionConnected
30
30
30
30
Operation Guide 5519
●
Stopping Radio Wave
Emission by This
Watch
The watch is emitting radio waves whenever
the second hand is pointing to e (Bluetooth
connected) or “R” (Bluetooth connection
standby).
the second hand is not pointing at e or
Even if
“R”, the watch will automatically attempt to
connect with a phone four times a day to adjust
its time settings.
When in a hospital, on an aircraft, or in any
other area where
the use of radio waves is not
allowed, use the operations below to stop
radio wave generation.
●
Stopping Radio Wave Generation
Press any button
to terminate the Bluetooth
connection.
●
Disabling Auto Time Adjustment
Configure CASIO WATCH+ settings to
disable synchronization between the watch
and phone.
l Entering the Watch Airplane Mode
Copyrights and Registered Copyrights
●
Bluetooth® is a registered trademark of
Bluetooth SIG, Inc.
●
iPhone and App Store are registered
trademarks of Apple Inc. in the United
States and other countries.
●
iOS is a trademark or registered trademark
of Cisco Systems, Inc.
●
GALAXY, GALAXY Note, and GALAXY S
are registered trademarks of Samsung
Electronics Co., Ltd.
●
Android and Google PlayTM are registered
trademarks of Google Inc.
●
Other company names and product names
used herein are trademarks or registered
trademarks of their respective companies.
Troubleshooting
I can’t pair the watch with a
phone.
Q1
I’ve never been able to establish a
(pairing) connection between the
watch and phone.
Are you using a supported phone model?
Check if the phone model and its
operating system are supported by the
watch.
For information about supported phone
models, visit the CASIO Website.
http://world.casio.com/os_mobile/wat/
Is CASIO WATCH+ installed on your
phone?
The CASIO WATCH+ needs to be
installed in order to connect with the
watch.
A Installing applications
l
Are your phone’s Bluetooth settings
configured correctly?
Configure the phone’s Bluetooth settings.
For details about setting procedures, see
your phone documentation.
iPhone Users
●
“Settings”n“Bluetooth”n On
●
“Settings” n “Privacy
Sharing” n “CASIO WATCH+” n On
Android Users
●
Enable Bluetooth.
Other than the above.
Some phones need to have BT Smart
disabled to use CASIO WATCH+. For
details about setting
phone documentation.
On the Home Screen, tap: “Menu” n
“Settings” n “Bluetooth” n
Smart settings” n “Disable”.
”
n “Bluetooth
procedures, see your
“Menu” n “BT
I can’t reconnect the watch
and phone.
Q1
The watch will
phone after they are disconnected.
Is CASIO WATCH+ running on your
phone?
The watch cannot re-connect with the
phone unless CASIO
on the phone. On the phone’s Home
Screen, tap the CASIO WATCH+ icon.
Then on the watch, hold down the
CONNECT button (C) for about 1.5
seconds.
Have you tried turning your phone off and
then back on again?
Turn the phone off and then back on, and
then tap the
on the watch, hold down the CONNECT
button (C) for about 1.5 seconds.
Q2
I can’t connect while my phone is in
the Airplane Mode.
Connection with the watch is not possible while
the phone is in the Airplane Mode. After exiting
the phone’s Airplane Mode, go to its Home
Screen and tap the “CASIO WATCH+” icon.
Then on the watch, hold down the CONNECT
button (C) for about 1.5 seconds.
Q3
I can’t connect while the watch is in
the Airplane Mode.
Exit the watch’s Airplane Mode. Then hold
down the CONNECT button (C) for about 1.5
seconds.
not re-connect with the
WATCH+ is running
CASIO WATCH+ icon. Next,
15
30
30
30
Operation Guide 5519
Q4
I changed the phone’s Bluetooth
from enabled to disabled, and now I
can’t connect anymore.
On the phone, disable and then re-enable
Bluetooth, and then go to the Home Screen
and tap the
the watch, hold down the CONNECT button
(C) for about 1.5 seconds.
Q5
Turn on the phone and tap the CASIO WATCH+
icon. Then on the watch, hold down the
CONNECT button (C) for about 1.5 seconds.
“CASIO WATCH+”
I can’t connect after turning off the
phone.
Phone-Watch Connection
Q1
I can’t establish a connection
between the phone and watch.
Have you tried turning your phone off and
then back on again?
Turn the phone off and then back on, and
tap
then
on the watch, hold down the CONNECT
button (C) for about 1.5 seconds.
Has the watch been re-paired with the
phone?
CASIO WATCH+ icon. Next,
the
icon. Next, on
Changing to a Different
Phone Model
Q1
Connecting the current watch to
another phone.
Pair the watch with the phone.
C Pairing the watch with a phone
l
Phone Finder
Q1
Phone Finder does not work.
Are the phone and watch disconnected?
Phone Finder does not work during
Bluetooth connection.
Is CASIO WATCH+ running on your
phone?
Phone Finder will not work unless CASIO
WATCH+ is running. On the Home
Screen, tap the CASIO WATCH+ icon.
Other than the above.
If the phone does not respond after a few
seconds, it could mean that the phone is
located too far
a different location and try again.
Q2
It takes some time before the phone
responds.
The phone will emit a tone when a connection
is established with the watch, which takes a
few seconds.
Q3
The phone cannot be found even
when it is close to the watch.
Since communication is performed using
radio
waves,
the phone even if it is within two meters.
Certain environments may make the
allowable communication range very short.
from the watch. Change to
the
watch may not be able to find
Checking Email
Q1
What types of mail accounts can be
checked for mail?
@gmail.com, @yahoo.com, @yahoo.co.jp,
@icloud.com,
@i.softbank.jp, @outlook.jp, @outlook.com
Q2
The CASIO WATCH+ supports registration of
up to five mail accounts.
Q3
The watch’s mode hand indicates whether or
not you have new mail on your phone.
●
If the mode hand is pointing at l, it means
you’ve got new mail.
●
If the mode hand is pointing at ¢, it means
you do not have any new mail.
Q4
The email check operation takes about 10
seconds.
Q5
Did you register your account?
Use the CASIO WATCH+ to register the
email account you want to check.
Is the CASIO WATCH+ running?
Check if CASIO WATCH+ is running on
the phone. On the Home Screen, tap the
CASIO WATCH+ icon.
@aol.jp, @aol.com,
How many mail accounts can be
configured for incoming mail alert?
What mail information does the
watch show?
It takes time before mail check
information is indicated
The watch is not checking for email.
@aim.com,
by the watch.
After unpairing the watch and phone, repair them again.
Unpairing
l
If you are unable to establish a
connection...
Delete the pairing information from the
watch, and then re-pair the watch and
phone.
See the Note under "Unpairing".
l
16
30
Operation Guide 5519
Auto Time Adjustment
Q1
When does the watch sync its time
setting with the phone?
The watch will connect with the phone and
perform
auto time
a.m., 6:30 a.m., 12:30 p.m. and 6:30 p.m. The
connection is automatically terminated after
auto time adjustment is complete.
Q2
The watch time setting is not
adjusted when an auto adjustment
time is reached.
Is auto time adjustment not being
performed according to its normal
schedule?
Note that auto time adjustment is not
performed for 24 hours after swapping of
the Home Time and World Time, or after
the time setting is adjusted manually on
the watch. Auto time adjustment will
resume 24 hours after either of the above
operations is performed.
Is the watch in the Airplane Mode?
Auto time adjustment will not be
performed at the scheduled times if the
watch is in the Airplane Mode. Exit the
watch’s Airplane Mode.
Entering the Watch Airplane Mode
l
Q3
Time is not displayed correctly.
The phone’s time setting may be incorrect
because it is unable to connect with its
network due to being out of range, etc. If this
happens, connect the phone to its network
and then adjust the time setting.
World Time
Q1
The time for a World Time City is not
correct.
The summer time start date and time, end date
and time, or other rules were changed by
authorities.
Q2
After swapping your current location
(Home City) time with the World
Time, the World
correct.
Use the CASIO WATCH+ to specify a World
Time City.
adjustment at around 12:30
Time City time is not
Hand Movement and
Indications
Q1
I don’t know what mode the watch is
in.
You tell which mode the watch is currently in
by checking the position of the mode hand.
Navigating Between Modes
l
●
Hold down (A) for about two seconds to
enter the Calendar Mode.
Q2
Why can’t I perform any button
operations while high-speed hand
movement is in progress?
Except for the mode navigation button, button
operation is disabled while high-speed hand
movement is in progress after a watch setting
is changed, etc. Wait until the hands stop
moving before performing button operations.
Q3
The second hand is jumping at twosecond intervals.
Battery power is low. Keep the watch exposed
to light until it recharges sufficiently.
Solar Charging
l
Q4
All hands are stopped at 12 o’clock
and buttons do not work.
The battery is dead. Keep the watch exposed
to light until the battery recharges sufficiently.
Solar Charging
l
Q5
The hands suddenly start moving at
high speed.
This is due to one of the reasons below, and
does not indicate malfunction. Simply wait
until normal hand movement resumes.
●
The watch is recovering from a power
saving state.
Power Saving
l
●
Establish a connection with the phone and
correct the time setting.
Auto Time Adjustment
l
Q6
Hands are stopped and buttons do
not work.
The watch is in the charge recovery mode.
Wait until the recovery process is complete
(for
about 15
more quickly if you place it in a brightly lit
location.
Q7
Strong magnetism or impact may cause the
hands of the watch to go out of alignment. Use
CASIO WATCH+ to correct hand alignment.
Correcting Hand Alignment
l
Q8
The day is in the process of changing. For
information about how the day changes, see
the section below.
Hands and the Day Indicator Movement
l
minutes). The watch will recover
Hands and the day indicator are out
of alignment.
The time setting is correct, but the
day indicator is between days.
Crown Operations
Q1
Nothing happens when I rotate the
crown.
If you do not perform any operation for about
two minutes after pulling out the crown
(approximately
and day indicator alignment operations),
crown operations will automatically become
disabled. If that happens, push the crown back
in and then pull it out again.
Using the Crown
l
Q2
Crown operation is disabled while high-speed
hand movement is in progress after a watch
setting is changed, etc. Wait until the hands
stop moving before performing crown
operations.
30 minutes
Crown operation does not work.
in the case of hand
Charging
Q1
The watch does not work even
though it is exposed to light.
The watch stops operating whenever the
battery goes dead. Keep the watch exposed
to light until it recharges sufficiently.
Solar Charging
l
17
Loading...