Casio 5236 User Manual
MA1104-EA
Operation Guide 5168/5236
Your watch may differ somewhat from the one shown in the illustration. •
Hour hand
Minute hand
First click
(Setting day)
Second click
(Setting time)
Crown
Second hand
(Normal position)
Day
24-hour hand
[5168]
To set the time
Pull the crown out to the second click.1.
At this time, the second hand will move to • 0 (reset position) and stop there.
Set the hands by rotating the crown. Rotate the crown to move the hands 2.
clockwise. Move the minute hand four or five minutes past the time you want to
set, and then back it up to the proper setting.
Carefully set the time, making sure to distinguish between AM and PM. •
Push the crown back in to the normal position to restart timekeeping.3.
To set the day
Pull the crown out to the first click.1.
Set the day by rotating the crown.2.
Push the crown back in to the normal position.3.
Avoid changing th e date setting w hile the current t ime is between 9:00 p.m. and •
1:00 a.m.
Hour hand
Second hand
Minute hand
Day
24-hour hand
[5236]
First click
(Setting day)
Crown
(Normal position)
Using the Stopwatch
Stopwatch hour hand
(10 hours)
Stopwatch second hand
(37 seconds)
[5168]
Stopwatch minute hand
(2 minutes)
Stopwatch 1/20 second hand
(.8 second)
This hand mov es right and left •
to indicate the 1/20 second
count during the first
60 seconds.
Second click
(Setting time)
For a watch with an elapsed time bezel ■
Rotate the elapsed time bezel to align the
minute hand.
After certain am ount of time el apsed, read the gr aduation on
the elapsed time bezel which the minute hand points to.
The elapsed time is indicated.
Some water resist ant models are equ ipped with a screw •
lock crown.
With such model s, you must uns crew the crown in the •
direction noted in the illustration to loosen it before you can
pull it out. Do not pull too forcibly on such crowns.
Also note that such watches are n ot water resistant while •
their crowns are loo sened. Be sure to screw the crowns
back in as far as they will go after making any setting.
mark with the
Elapsed time bezel
Specifications
Accuracy at normal temperature: ± 20 seconds a month
Display: 3 analog hands (timekeeping hour and minutes, stopwatch seconds),
4 dials (timekeeping 24-hour, timekeeping seconds/stopwatch 1/20 second,
stopwatch hours, stopwatch minutes), day
Stopwatch function: Measuring capacity: 11:59'59.95"
Battery: One silver oxide battery (Type: SR927W)
Approximately 2 years on type SR927W
Measuring unit: 1/20 second
Measuring mode: Elapsed time
Stopwatch hour hand
(10 hours)
Stopwatch second hand
(37 seconds)
[5236]
The stopwatch lets you measure elapsed time up to 11 hours, 59 minutes,
59.95 seconds.
To measure elapsed time
Press 1. B to enter the Stopwatch Mode.
The stopwatch 1/20 second hand will move to the 0 position. •
Press 2. A to start the stopwatch.
Press 3. A to stop the stopwatch.
You can resume the measurement operation by pressing • A again.
Check the elapsed time.4.
The example above shows an elapsed time of 10 hours, 2 minutes, •
37.80 seconds.
Press • B to reset the stopwatch.
To return the function of the stopwatch 1/20 second hand to the timekeeping
second hand (indicating the current seconds count), press B again. This wil l
enter the Timekeeping Mode.
Notes:
Do not try to perform stopwatch operations while the crown is pulled out either •
to the first or s econd click. If you try to press a button, you mi ght accidentally
cause the crown to rotate and change the current time or day setting.
If the starting positions of t he stopwatch sec ond hand and 1/2 0 second hand •
become misaligne d, use the foll owing procedures to a djust the posit ion of the
stopwatch second hand so it points to 12 o’clock and the 1/20 second hand so
it points to .0 when the stopwatch is reset.
To adjust the positions of the stopwatch hands
Press 1. B to reset the st opwatch, and che ck the alignment of the stopwat ch
second hand (12 o’clock) and 1/20 second hand (12 o’clock).
Pull out the crown to the second click.2.
Press 3. A to move the stopwatch second hand.
If the stopwatc h 1/20 second h and is aligned correctly, proceed to step 5. If 4.
the stopwatch 1/20 second hand is also misaligned, press B to move the
stopwatch 1/20 second hand.
After making th e adjustments y ou want, push th e crown back in to its normal 5.
position.
Note that pulling the crown out also stops the timekeeping second hand. After •
performing the above procedure, you should also adjust the timekeeping setting.
Stopwatch minute hand
(2 minutes)
Stopwatch 1/20 second hand
(.8 second)
This hand mov es right and left •
to indicate the 1/20 second
count during the first
60 seconds.
1
Loading...