Carrier split room air conditioner remote control, CS457-R14A, R14E, R14A E, R14C User Manual

2020550A6722

1

2

3

4

6

7

8

9

9

10

10

11

14

Handling the remote controller ......................................................

Remote controller Specifications...................................................

Function buttons .................. .........................................................

Indicators on LCD ..........................................................................

How to use the buttons

Setting the clock ..............................................................................

Recessed button operation ............................................................

Auto operation.................................................................................

Cooling/Heating/Fan operation......................................................

Dehumidifying operation ...............................................................

Adjusting air flow direction............................................................

Timer operation...............................................................................

Sleep operation ..............................................................................

CONTENTS

Use the remote controller within a distance of 8
meters from the appliance, pointing it towards the
receiver. Reception is confirmed by a beep.

Location of the remote controller.

8m

CAUTIONS

The air conditioner will not operate if curtains, doors or other materials
block the signals from the remote controller to the indoor unit.
Prevent any liquid from falling into the remote controller. Do not expose
the remote controller to direct sunlight or heat.
If the infrared signal receiver on the indoor unit is exposed to direct
sunlight, the air conditioner may not function properly. Use curtains to
prevent the sunlight from falling on the receiver.
If other electrical appliances react to the remote controller. either move
these appliances or consult your local dealer.

The remote controller is powered by two dry batteries(R03/LR03X2) housed in the
rear part and protected by a cover.
(1) Remove the cover by pressing and sliding off.
(2) Remove the old batteries and insert the new batteries,placing the(+) and (-)
ends correctly.
(3) Reattach the cover by sliding it back into position.
NOTE: When the batteries are removed, the remote controller erases all progra­mming. After inserting new batteries, the remote controller must be reprogrammed.

Replacing batteries

Handling the remote controller

2

Keep the remote controller where its signals can
reach the receiver of the unit. When you select the
timer operation, the remote controller automatically
transmits a signal to the indoor unit at the specified
time. If you keep the remote controller in a position
that hinders proper signal transmission, a time lag of
up to 15 minutes may occur.

M
O

DE

FA
N S

P
EED

T
E
M

P.

A
IR D

I
REC

TI
ON

S
WING

L
ED

SLEEP

T
URB

O

CL
O

CK

T
IME

R

CANCEL

RESET

F/C

CAUTIONS

Do not mix old and new batteries or batteries of different types.
Do not leave the batteries in the remote controller if they are not going to be
used for 2 or 3 months.
Do not dispose batteries as unsorted municipal waste. Collection of such
waste separately for special treatment is necessary.

Model

Lowest Voltage of
CPU Emitting Signal

Rated Voltage

8m (when using 3.0 voltage,
it gets 11m)

3.0V(Dry batteries R03/LR03×2)

2.4V

Remote Controller Specifications

1. Operating Mode: AUTO, COOL, DRY, HEAT(Cooling only
model without), and FAN.

2. Timer Setting Function in 24 hours.

。 。

O O

3. Indoor Setting Temperature Range : 17 C~30 C(62 F~88 F).

4. Full function of LCD (Liquid Crystal Display)

Environment

Signal Receiving
Range

Performance Feature

Function buttons

1

2

Each time the button is pressed, the operation
mode is selected in a sequence of following:

3

MODE Button

3 4

1

1

2

2

4

4

5

5

6

6

3

3

8

8

7

7

9

9

10

10

11

11

12

12

13

13

4

SWING Button
Used to stop or start auto swing feature of
the louver. Press it again to stop the movement.

5

6

7

8

ON/OFF Button
Operation starts when this button is pressed
and stops when this button is pressed again.

NOTE: Heat mode is for Cooling & Heating models only.

AUTO

COOL

DRY

HEAT FAN

Used to select the fan speed in four steps:
Auto Low Med High

FAN SPEED Button

9

R14A/(C)E, RG14A1/(C)E, RG14A2/(C)EF.

Carr ier

Carr ier

15

14

15

AIR DIRECTION Button: Press this button to
change the swing angle of louver and set the
desired up/down airflow direction. The louver
swings for an angle of 6 for each press.

。 。

-5 C 60 C( )

~

O O

23 F~140 F

MODE

MODE

FAN SPE ED

FAN SPE ED

TEMP.

TEMP.

AIR DI RECTI ON

AIR DI RECTI ON

SWIN G

SWIN G

LED

LED

SLEE P

SLEE P

TURB O

TURB O

CLOC K

CLOC K

TIME R

TIME R

CANC EL

IONI ZER

CANC EL

RESET

RESET

F/C

F/C

AUT O

AUTO

COO L DRY HEAT FAN

COO L DRY HEAT FAN

SET TEM P.

SET TEM P.

CLOCK

CLOCK

TIMER ON

TIMER ON

TIMER OFF

TIMER OFF

SPEED

SPEED

AUTO LOW MED HIGH

AUTO LOW MED HIGH

ON

ON

OFF

OFF

LED Button

Press this button to clear the digit display in
the air conditioner, press it again to activat it.
(NOTE:there is no reation to some air
conditioners without digital display when you
press the LED button.)

RESET Button
Once the recessed RESET button is pressed,
all of the current settings will be cancelled and
the controller will return to the initial settings.

F/C Button

Used to select/display temperature settings in
either Celsius or Fahrenheit . Press this button
to select either the Celsius or Fahrenheit scale.

,

,

,

,

,

,

,

,

But tons: T he se t hre e butto n is
dis able fo r model R 14A/( C)E.

TEMP. Button :
Push the button to increase the indoor
temperature setting or to adjust the TIMER
in a clockwise direction. Push the button
to decrease the indoor temperature setting
or to adjust the TIMER in a counter-clockwise
direction.

Mode l: R 14A /E ,
R14A /C E.

Mode l: R G14 A1 /E,
RG14 A1 /CE .