Carlo Gavazzi UC 80 CND 60 . P M1 TR Data Sheet
Specifications are subject to change without notice (19.07.2005) 1
Ultrasonic
Diffuse, Dual Transistor Outputs
Type UC 80 CND 60 . P M1 TR
Product Description
Ultrasonic sensor
Housing style
Housing size
Housing material
Housing length
Detection principle
Sensing distance
Output type
Output configuration
Connection
Remote teach
Type Selection
Housing Connection Rated operating Outputs Ordering no.
dimensions dist. (S
n
)
80 x 80 x 50 mm Plug M12, 5 pin 600-6000 mm 2 x PNP, NO/NC UC 80 CND 60 PP M1 TR
80 x 80 x 50 mm Plug M12, 5 pin 600-6000 mm 2 x NPN, NO/NC UC 80 CND 60 NP M1 TR
Ordering Key
UC80CND60PPM1TR
A self-contained multi function diffuse ultrasonic sensor
with a sensing range of 600
to 6000 mm. 2 switching
outputs - easily set up for 3
different switching modes
and adjusted by teach-in makes it ideal for level control tasks in a wide variety of
vessels. A sturdy one-piece
ABS housing provides the
perfect packaging for the
sofisticated microprocessor
controlled and digitally filtered sensor electronics.
Excellent EMC performance
and precision are typical
features of this sensor
based on true distance
measurement.
Technical Data
Rated operational volt. (Ue) 15 to 30 VDC (ripple included)
Ripple ≤ 10%
Output current (Ie) max. 500 mA (continuous)
No-load supply current (Io) ≤ 80 mA
Protection Short-circuit, transients and
reverse polarity
Rated insulation voltage > 1 kV
Output 2 PNP or NPN open collector
outputs, NO or NC
Power-on delay 200 ms
Voltage drop (Ud) < 0.5 V
Off-state current (Ir) < 10 µA
Teach-in Set point adjustment NO/NC selection
Switching modes selection
Indication Set points, 2 LEDs yellow
Echo, 1 LED green
Rated operating distance 600 - 6000 mm
Operating frequency 0.5 Hz
Carrier frequency 80 kHz
Response time 70 ms (target speed 1 m/s
in beam direction)
700 ms (step response)
Hysteresis (H) (differential travel) Programmable
Temperature compensation Ye s
Beam angle 8°
Ambient temperature
Operating and Storage -15° to +70°C (5° to +158°F)
Environment
Overvoltage category II (IEC 60664/60664A,
60947-1)
Pollution degree 3 (IEC 60664/60664A,
60947-1)
Degree of protection IP 65 (IEC 60529, 60947-1)
Housing material ABS
Connection Plug M12, 5-pin
Cables for plug (M1) CONM15 series
Weight 300 g
CE-marking Yes
• Square 80 mm ABS housing
• Sensing distance: 600 - 6000 mm
• Remote Teach by wire
• Outputs: 2 multi function switching outputs PNP or
NPN, NO or NC
• Setup of "Normal Switching", "Window" or "Adjustable
Hysteresis" function
• Power supply: 15 to 30 VDC
• 8° beam angle
• Protection: Short-circuit, reverse polarity, transients
• Protection degree IP 67
• M12 plug, 5 pin
2 Specifications are subject to change without notice (19.07.2005)
UC 80 CND 60 . P M1 TR
Switching Operation
Distance
P1 P2
Distance
P1 P2
Distance
P1 P2
Distance
NO Characteristics
NC Characteristics
Normal Switching Operation
Windows Function
Hysteresis Adjustment
The following 3 different modes of the switching outputs can
be selected:
I Normal switching function
II Window function
III Adjustable hysteresis
All these functions may be programmed/taught by means of
the Teach-in input (pin 5) present in the connector. Each
mode has a unique indication using the Echo, P1 and P2
LEDs. The programming/Teach-In procedure is shown in the
following flow diagram:
Teach in of switching output SP1
Position P1 Switching output can be
either NO or NC.
Teach in of switching output SP2
Switching output can be either NO or NC.
Window function / Selection of Hysteresis Mode
SP1 is switching when object is between P1
and P2. SP2 is switching when the object is
NOT between P1 und P2.
Hysteresis adjustment of set points at P1
Distance between P1 and P2 determines the
hyteresis of the switching outputs. SP1 has
NO and SP2 has NC characteristics.
Teach-In for
8 sec
14 sec
20 sec
Normal function:
The Echo LED is ON when an echo is received (alignment
LED). P1 and P2 LEDs are indicating status of the switching
outputs.
Echo P1 P2
Green Yellow Yellow
Wiring Diagram
Teach-In for
14 sec
Teach-In for
20 sec
Teach input is
active when
5 BE wire is
connected to
Ground (3 BU).
Teach input is
active when
5 BE wire is
connected to
Ground (3 BU).
PNP
SP1
SP2
1 BN
5 PK (GY)
4 BK
2 WH
3 BU
43
5
2
1
SP 1
SP 2
SP 1
SP 2
P 1 P2
P 2
P1
D ist anc e
NPN
SP 1
SP 2
SP 1
SP 2
1 BN
SP1
SP2
4 BK
2 WH
5 PK (GY)
3 BU
P1 P2
43
5
2
1
P1 P2
D ist anc e
Loading...