CaptiveAire PXR3 Installation Manual

SV C1 C2 AL1 AL2

Micro-contr oller X

SEL

Model: PXR3

Operation Manual

ECNO:409c

1 Part Names and Functions .................................................................................................... 5

2 Operations ............................................................................................................................. 6

2-1 Parameter list............................................................................................................ 6

2-2 Basic operations ....................................................................................................... 11

2-3 Parameter functions and method of settings ............................................................ 12

① First block parameters ............................................................................................... 13

Standby setting .......................................................................................................... 13

Ramp-soak control..................................................................................................... 14

Canceling the alarm latch .......................................................................................... 15

Auto-tuning function................................................................................................... 16

Displaying ON-delay alarm or the remaining time of timers ...................................... 17

Setting alarm 1 and 2 ................................................................................................ 18

Upper limit of alarm 1 and 2 ...................................................................................... 18

Lower limit of alarm 1 and 2....................................................................................... 18

Key lock ..................................................................................................................... 19

② Second block parameters .......................................................................................... 20

Proportional band ...................................................................................................... 20

Integral time ............................................................................................................... 21

Derivative time ........................................................................................................... 22

Hysteresis range for ON/OFF control ........................................................................ 23

Cooling-side proportional band coefficient ................................................................ 24

Cooling-side proportional band shift (Dead band/Overlap band) .............................. 25

Output offset value..................................................................................................... 26

Anti-reset windup ....................................................................................................... 26

Control algorithm ....................................................................................................... 27

PV (Measured value) stable range ............................................................................ 31

HYS (Hysteresis) mode at ON/OFF control............................................................... 32

Cycle time of control output 1 .................................................................................... 33

Cycle time of control output 2 (cooling-side).............................................................. 34

Input signal code........................................................................................................ 35

Setting lower limit of the measuring range................................................................. 36

Setting upper limit of the measuring range ................................................................ 36

Decimal point position................................................................................................ 38

PV offset .................................................................................................................... 39

SV offset .................................................................................................................... 40

Time constant of input filter........................................................................................ 41

Alarm types................................................................................................................ 42

Selecting ramp-soak patterns.................................................................................... 45

Ramp-soak status display.......................................................................................... 46

1st to 8th target SV .................................................................................................... 46

1st to 8th ramp segment time .................................................................................... 46

1st to 8th soak segment time..................................................................................... 46

Ramp-soak modes..................................................................................................... 46

③ Third block parameters .............................................................................................. 49

Specifying control system and action, and output direction at input burn-out............ 49

SV (Setting value) lower limiter.................................................................................. 50

SV (Setting value) upper limiter ................................................................................. 50

The time of ON-delay alarm or timer function............................................................ 51

Hysteresis alarm 1 and 2........................................................................................... 53

Options of alarm 1 and 2 ........................................................................................... 54

Upper and lower limits for control output 1 ................................................................ 56

Upper and lower limits for control output 2 ................................................................ 56

Output limit types ....................................................................................................... 57

Output value display .................................................................................................. 58

RCJ (Cold junction compensation) ............................................................................ 59

Adjusting the PV (Measured value) display (0%)....................................................... 60

Adjusting the PV (Measured value) display (100%)................................................... 60

DI operation ............................................................................................................... 61

Station No. for communication ................................................................................... 64

Parity for communication ........................................................................................... 65

Input type for PYP...................................................................................................... 66

Retransmisson output type setting ............................................................................ 67

Retransmisson base scale......................................................................................... 68

Retransmisson span scale......................................................................................... 68

Parameter display mask ............................................................................................ 69

3 Troubleshooting...................................................................................................................... 70

Index ......................................................................................................................................... 72

digit

24 × 48 mm

Thermocouple °C Thermocouple °F RTD Pt100Ω 3-wire type °C RTD Pt100Ω 3-wire type °F 1 to 5V DC 4 to 20mA DC

Relay contact output SSR/SSC driving output 4 to 20mA DC output

None Relay contact output SSR/SSC driving output 4 to 20mA DC output

None Alarm 1 point 8 ramps/soaks Alarm 1 point + 8 ramps/soaks Alarm 2 point Alarm 2 point + 8 ramps/soaks

None 100 to 240V AC Japanese 100 to 240V AC English 100 to 240V AC None 24V AC/24V DC Japanese 24V AC/24V DC English 24V AC/24V DC

None

RS-485 Modbus interface

RS-485 Z-ASCLL interface Retransmission + Digital input 1 point Retransmission Digital input 2 points RS-485 Modbus interface + Digital input 1 point RS-485 Z-ASCLL interface + Digital input 1 point

<Non-standard specification>

Non-standard parameter setting

Specification Note

PXR

Note 1 Note 1 Note 1

Note 2 Note 2

Note 3 Note 3

45678 9

T R N S A B

A C E

Y A C E

10 11 12 13 14

0 1 4 5 F

N Y V C A B

Model Specifications

Note 1

Process alarm (2 points) (the codes “ F and G ” in the 9th digit) cannot be specified.

Note 2

Control output 2 (the codes “ A, C, and E ” in the 7th digit) cannot be specified.

Note 3

Control output 2, communication digital input (2 points), alarm (2 points), and 24V power supply (the codes “ A, C and E ” in the 7th digit, “ F and G ” in the 9th digit, and “ A, B, and C ” in the 10th digit) cannot be specified.

The default settings of input signals, measured ranges, and setting values are shown below.

Thermocouple specified : Thermocouple K, Measured range: 0 to 400°C,

Resistance bulb specified : Pt, Measured range: 0 to 150°C, Setting value:

Voltage, Current specified : Scaling: 0 to 100%, Setting value: 0%

In any case other than the description above, specify input signals and measured range.

The input signals for the thermocouple and the resistance bulb can be switched with the front panel keys.

0 0 0 0 0 0 0 0

The default settings of control action is reverse for control output 1 and direct for control output 2. The reverse and direct actions can be switched with keys on the face panel.

Setting value: 0°C

0°C

This chapter explains the part names and functions on the face panel. The f ace panel has the PV and SV displays, the status indicating lamp, and the setting keys, etc. Those functions are explained below. Please read and understand them before using the PXR. For details about the setting of parameters, see Chapter 2.

Part Names and Functions

Lampforcontroloutput1① Lampforcontroloutput2②

Lampforalarmoutput1③ Lampforalarmoutput2④

SV C1 C2 AL1 AL2

⑥ key

Type:PXR3

q Lamp for control output 1

Lights up while control output 1 stays ON.

w Lamp for control output 2

Lights up while control output 2 stays ON.

e Lamp for alarm output 1 (option)

Lights up when alarm output 1 is actuated. Flickers under ON-delay operation.

SEL

⑤Display⑨SVlamp

⑦ key

SEL

Used to switch the PV display to/from the SV display and select a parameter block and a parameter, and re gister a set value.

u keys

Used to change the SV, call parameters, and change parameter values.

⑧Auto-tuning/self-tuninglamp

key

r Lamp for alarm output 2 (option)

Lights up when alarm output 2 is actuated. Flickers under ON-delay operation.

t Display

Displays the PV (process value) or SV (set value). When setting a parameter, its name or its value appears.

i Auto-tuning/self-tuning lamp

Flickers under an auto-tuning or self-tuning operation.

o SV lamp

Displays the PV (process value) in normal condition (while the lamp stays out). Press the up the SV lamp and display the SV (set value). Note that the lamp stays out while parameters and data are displayed. Flickers while the display shows the PV (process value) in standby state.

key to light

SEL

Operations

This chapter explains how to set the SV (Setting value) and the parameters for the PXR.

2-1 Parameter list

Parameters for the PXR are classified under three blocks according to the frequency of use. The parameters of the second and third blocks are used at initialization or when they are of absolute necessity. Some parameters may not be displayed at the time of delivery depending on the type of the instrument.

Parameters of the first block

Parameter

display symbol

Parameter name

Standby

Stby

setting

AL1

AL2

LoC

Ramp-soak control

Alarm latch cancel

Auto-tuning

Timer 1 display Timer 2 display Set value of

alarm 1

Lower limit value of alarm 1

Upper limit value of alarm 1

Set value of alarm 2

Lower limit value of alarm 2

Upper limit value of alarm 2

Key lock

ProG

LACH

TM-1 TM-2

A1-L

A1-H

A2-L

A2-H

Description

Switches between RUN and Standby for control.

Switches between Start, Stop, and Hold for ramp-soak control

Cancels the alarm latch.

Used for setting the constants for , , and by auto-tuning.

Displays the remaining time of timer 1. Displays the remaining time of timer 2.

Sets the value at which alarm 1 is detected.

Sets the lower limit value at which alarm 1 is detected.

Sets the upper limit value at which alarm 1 is detected.

Sets the value during which alarm 2 is detected.

Sets the lower limit value at which alarm 2 is detected.

Sets the upper limit value at which alarm 2 is detected.

Specifies whether or not to allow the change of parameters.

is displayed when alarm type 1 is 0 to 15, or 32 to 34, and or is displayed when alarm type 1 is 16 to 31.

is displayed when alarm type 2 is 0 to 15 or 32 to 34, and or is displayed when alarm type 2 is 16 to 31.

Setting range and

factory default setting (*)

oN: Control standby

(Output: OFF, Alarm: OFF)

oFF: Control RUN* oFF: Stop*

rUn: Start HLd: Hold

0: Keeps the alarm latch.* 1: Opens up the alarm latch.

0: OFF (Resets the auto-tuning or does

not use it.)*

1: ON (Performs the auto-tuning in the

SV standard type.)

2: ON (Performs the auto-tuning in

low PV type (SV value-10%FS).)

- (Unit: seconds)

When the alarm type is absolute value: 0 to 100%FS (*:10)

When the alarm type is deviation:

-100 to 100%FS (*:10)

When the alarm type is absolute value: 0 to 100%FS (*:10)

When the alarm type is deviation:

-100 to 100%FS (*:10)

0: All settings are changeable both from

the face panel and via communication.*

1: All settings are unchangeable from the

face panel, but changeable via communication.

2: Only the SV is changeable from the

face panel, and all settings are changeable via communication.

3: All settings are changeable from the

face panel, but unchangeable via communication.

All settings are unchangeable from the face

panel or

via

Only the SV is changeable from the face

panel, but all settings are unchangeable

via

communication.

User’s

set value

Parameter mask DSP

dSP1-1

dSP1-2

dSP1-4

dSP1-8

dSP1-16 dSP1-32

dSP1-128

dSP2-1

dSP2-2

dSP2-4

dSP2-8

dSP2-16

dSP3-1

Reference

page

17 17

18 18 18 18 18 18

Note: The parameters for which * is marked with the page number in Reference page are related to Remedies

of “4” on page 70.

Parameters of the second block

Parameter display symbol

Parameter name

Proportional

band Integral time

Derivative time

Hysteresis range for

HYS

ON/OFF control

Cooling-side

bAL

proportional band coefficient

Cooling-side proportional band shift

Output convergence value

Anti-reset windup

CooL

Description

Set to 0.0 to select the ON/OFF control (Two-position control).

Sets the hysteresis for ON/OFF control.

Note: The p ar ameters for which * is marked with the page number in

Reference page are related to Remedies of “4” on page 70.

Setting range and factory

default setting (*)

0.0 to 999.9% (*: 5.0)

0 to 3200 seconds (*: 240)

0.0 to 999.9 seconds (*: 60.0) 0 to 50%FS (*: equivalent of 1.0°C)

0.0 to 100.0 (*: 1.0)

-50.0 to +50.0 (*: 0.0)

-100 to 100% (*: single 0.0, dual 50.0)

0 to 100%FS (*: 100%FS)

User’s

set value

Parameter mask DSP

dSP3-2

dSP3-4 dSP3-8 dSP3-16

dSP3-32

dSP3-64

dSP3-128

dSP4-1

Reference

page

20 21

25 26

CTrL

SLFb

onoF

TC2

P-n2

P-SL

P-SU

P-dP

P-F

PVOF

SVOF

P-dF

ALM1

ALM2

STAT

PTn

Sv-1

TM1r

Control algorithm

PV (Measured value) stable range

Setting HYS (Hysteresis) mode

Cycle time of control output 1

Cycle time of control output 2 (cooling-side)

Input signal code

Lower limit of measuring range

Upper limit of measuring range

Setting the decimal point position

°C / °F selection

PV (Measured value) offset

SV (Setting value) offset

Time constant of input filter

Alarm type 1 Alarm type 2 Status display

of ramp-soak Selecting

ramp-soak execute type

1st target value

/Switching-SV value

First ramp segment time

Selects the control algorithm.

Sets the PV stable range for the selftuning operation.

Selects the hysteresis operation at ON/OFF control.

Not shown at 4-20mA DC output

Set this parameter when changing the types of temperature sensors.

Shift the display of the PV. Shift the SV. But the SV display

is not changed.

Sets the types of alarm operations. Sets the types of alarm operations.

Selects ramp-soak patterns.

Sets the 1st target SV of ramp-soak operation. / Selected at switchingSV function for DI1

Sets the first ramp segment time.

PID: Runs normal PID control.* FUZY: Runs PID control with fuzzy logic. SELF: Runs PID control with self-running.

0 to 100%FS (*: 2%FS)

oFF: Starts the two-position control at the

values of SV+HYS/2 and SV-HYS/2.

on:

Starts the two-position control at the values of SV and SV+HYS, or SV and SV-HYS.

RLY, SSR: 1 to 150 seconds

(*: Contact output = 30, SSR/SSC-driven output = 2)

RLY, SSR: 1 to 150 seconds (*: Contact output = 30, SSR/SSC-driven output = 2)

1 to 16 (*: specified by customer while ordering)

-1999 to 9999 (*: specified by customer while ordering)

0 to 2 (*: specified by customer while ordering)

°C / °F

-10 to 10%FS (*: 0)

-50 to 50%FS (*: 0)

0.0 to 900.0 seconds (*: 5.0)

0 to 34 (*: 0/5) 0 to 34 (*: 0/9)

- (*: OFF)

1: Performs 1st to 4th segments.* 2: Performs 5th to 8th segments. 3: Performs 1st to 8th segments.

Within the SV limit. (*: 0%FS)

0 to 99h59m (*: 0.00)

Note 1

dSP4-2

dSP4-4

dSP4-8

dSP4-16

dSP4-32

dSP4-64

dSP4-128

dSP5-1

dSP5-2

dSP5-4

dSP5-8

dSP5-16 dSP5-32

dSP5-64 dSP5-128 dSP6-2

dSP6-4

36 36 38

39 40

41 42

42 46

dSP6-8

dSP6-16

Parameter display symbol

Parameter name Description

TM1S

Sv-2

TM2r

TM2S

Sv-3

TM3r

TM3S

Sv-4

TM4r

TM4S

Sv-5

TM5r

TM5S

Sv-6

TM6r

TM6S

Sv-7

TM7r

TM7S

Sv-8

TM8r

TM8S

Mod

1st soak segment time

2nd target SV

2nd ramp segment time

2nd soak segment time

3rd target SV

3rd ramp segment time

3rd soak segment time

4th target SV

4th ramp segment time

4th soak segment time

5th target SV

5th ramp segment time

5th soak segment time

6th target SV

6th ramp segment time

6th soak segment time

7th target SV

7th ramp segment time

7th soak segment time

8th target SV

8th ramp segment time

8th soak segment time

Ramp-soak mode

Sets the 1st soak segment time.

Sets the 2nd target SV of ramp-soak operation.

Sets the 2nd ramp segment time.

Sets the 2nd soak segment time.

Sets the 3rd target SV of ramp-soak operation.

Sets the 3rd ramp segment time.

Sets the 3rd soak segment time.

Sets the 4th target SV of ramp-soak operation.

Sets the 4th ramp segment time.

Sets the 4th soak segment time.

Sets the 5th target SV of ramp-soak operation.

Sets the 5th ramp segment time.

Sets the 5th soak segment time.

Sets the 6th target SV of ramp-soak operation.

Sets the 6th ramp segment time.

Sets the 6th soak segment time.

Sets the 7th target SV of ramp-soak operation.

Sets the 7th ramp segment time.

Sets the 7th soak segment time.

Sets the 8th target SV of ramp-soak operation.

Sets the 8th ramp segment time.

Sets the 8th soak segment time.

Selects the power-on start, repeat, and standby functions for rampsoak operations.

Setting range and factory

default setting (*)

0 to 99h59m (*: 0.00)

Within the SV limit. (*: 0%FS)

0 to 99h59m (*: 0.00)

Within the SV limit. (*: 0%FS)

0 to 99h59m (*: 0.00)

Within the SV limit. (*: 0%FS)

0 to 99h59m (*: 0.00)

Within the SV limit. (*: 0%FS)

0 to 99h59m (*: 0.00)

Within the SV limit. (*: 0%FS)

0 to 99h59m (*: 0.00)

Within the SV limit. (*: 0%FS)

0 to 99h59m (*: 0.00)

Within the SV limit. (*: 0%FS)

0 to 99h59m (*: 0.00)

0 to 15 (*: 0)

User’s

set value

Parameter

mask DSP

dSP6-32

dSP6-64

dSP6-128

dSP7-1

dSP7-2

dSP7-4

dSP7-8

dSP7-16

dSP7-32

dSP7-64

dSP7-128

dSP8-1

dSP8-2

dSP8-4

dSP8-8

dSP8-16

dSP8-32

dSP8-64

dSP8-128

dSP9-1

dSP9-2

dSP9-4

dSP9-8

Reference

page

46 46 46

Note 1:When a customer does not specify the settings while ordering, the following settings are selected as factory defaults.

Thermocouple input: Thermocouple K Measured range: 0 to 400°C Resistance bulb input: Measured range: 0 to 150°C Voltage/Current input: Scaling: 0 to 100%

Parameters of the third block

Parameter display symbol

Parameter name Description

P-n1 Sv-L Sv-H

dLY1 dLY2

A1hy A2hy

A1oP

A2oP

PLC1

PHC1

PLC2

PHC2 PCUT

oUT1

oUT2

GAin

AdJ0

AdJS

STno

CoM

PYP

Ao-T

Control action

SV (Setting value) lower limiter

SV (Setting value) upper limiter

Delay time 1 Delay time 2

Alarm 1 hysteresis

Alarm 2 hysteresis

Alarm 1 options

Alarm 2 options

Lower limit for output 1 Upper limit for output 1 Lower limit for output 2 Upper limit for output 2

Output limit types

Output value (MV) display

RCJ (Cold junction compensation)

rCJ

setting

PV gradient User-definable zero

adjustment User-definable span

adjustment DI1 (Digital input 1)

di-1

operation DI2 (Digital input 2)

di-2

operation Station No.

Parity setting

Input type for PYP (Color TouchOperation Unit)

Retransmission output type

Note: The parameters for which * is marked with the page number in

Specifies control action and output at the input burn-out.

Sets the lower limit of the SV.

Sets the upper limit of the SV.

Delay time or timer value for alarm 1 relay. Delay time or timer value for alarm 2 relay.

Sets the hysteresis range of ON and OFF of alarm 1.

Sets the hysteresis range of ON and OFF of alarm 2.

Sets the optional functions of alarms 1 and 2.

Alarm latch (1: use, 0: not use)

Alarm of error status (1: use, 0: not use)

De-energized output (1: use, 0: not use)

Sets the lower limit for output 1. Sets the upper limit for output 1. Sets the lower limit for output 2. Sets the upper limit for output 2.

Sets the limit types of outputs 1 and 2 (breaking the limit, or maintained within the limit).

Displays the value of output 1.

Displays the value of output 2.

Sets the cold junction compensation function to ON/OFF.

Shifts the zero point of input value.

Shifts the span of input value.

Sets the DI1 operations.

Sets the DI2 operations.

Sets the station No. for communication.

Sets the parity for communication. (The baud rate is fixed at 9600bps.

Sets the input type for communicating with PYP.

Selecting retransmission output type.

0 to 19 (*: specified by customer while ordering)

0 to 100%FS (*: 0%FS)

0 to 100%FS (*: 100%FS)

0 to 9999 seconds (*: 0) 0 to 9999 seconds (*: 0)

0 to 50%FS (*: 1)

000 to 111 (*: 000)

-3.0 to 103.0% (*: -3.0)

-3.0 to 103.0% (*: 103.0)

-3.0 to 103.0% (*: -3.0)

-3.0 to 103.0% (*: 103.0)

0 to 15 (*: 0)

ON: Performs the RCJ compensation).* OFF: Does not perform the RCJ (Cold junction compensation).

0.001 to 2.000 (*: 1.000)

-50 to 50%FS (*: 0)

0 to 12 (*: 0=OFF)

0 to 255 (Setting to does not start the communications function.) (*: 1)

0: Odd parity* 1: Even parity 2: No parity

0 to 255 (*: 34)

0: PV/ 1: Set point/ 2: Output/ 3: Error (* : 0)

Reference page are related to Remedies of “4” on page 70.

Setting range and factory

default setting (*)

Note 2

(Cold junction

User’s

set value

Parameter

mask DSP

dSP9-16

dSP9-32

dSP9-64

dSP9-128 dSP10-1

dSP10-16

dSP10-32

dSP10-128

dSP11-1

dSP11-4 dSP11-8

dSP11-16 dSP11-32

dSP11-64

dSP11-128

dSP12-1

dSP12-2

dSP12-4 dSP12-8

dSP12-16

dSP12-32

dSP12-64

dSP12-128

dSP13-1

dSP13-2

dSP13-4

Reference

page

49 50 50

51 51

53 53 54

54 56

56 56 56

58 58

60 61 61

Ao-L

Ao-H

Retransmission base scale

Retransmission span scale

Setting retransmission base scale.

Setting retransmission span scale.

(Setting range: -100.0 to 100.0%) (* : 0.0%)

(Setting range: -100.0 to 100.0%) (* : 100.0%)

Note 2:The following settings are selected as factory defaults depending on the model you order.

Seventh digit = Y model: 0 Seventh digit = A, C, E model: 4

dSP13-8

dSP13-16

Parameter display symbol

Parameter name Description

Setting range and factory

default setting (*)

User’s

set value

Parameter

mask DSP

Reference

page

dSP9

dSP10

Parameter mask

Sets whether or not to display each parameter.

0 to 255 (*: specified by customer while ordering)

–

dSP13

dSP1

2-2 Basic operations

If it has not been operated for 30 seconds, the display returns to the PV display. Pressing the key for 2 second after setting parameters, the indication

shifts to the SV indication state.

Display state just after power-on

(PV indication)(SV indication)

SEL

(apporox. 1 second)

Parameters of the first block

Press the key to switch PV to / from SV.

SV lamp

Parameters of the second block

Parameters of the third block

Set data indication

Set data registration

Pressing and holding the keys makes the value increase or decrease fast.

SEL

(apporox. 3 second)

SEL

(apporox. 5 second)

SEL

Flickers when the set value is changed by pressing the or key. Stop flickering when the SV is registered by pressing the key.

Parameter setting

Basic operations for the PXR3

SEL

AL2

AL1

SEL

AL2

AL1

OFF

……indicatingPV Lit, flickers

……indicatingSV

Indication switching PV (process value) to / from SV (set value)

SEL

Just after power-on:

The PV (process value) is displayed just after power-on.

SV C1 C2 AL1 AL2

SEL

How to switch parameters:

The figure below shows the basic operations for the PXR3.

Exp.) In case when the PV (process value)

is 149.9.

How to set values:

key: One press increases the value by 1.

How to register the set data:

By pressing the

Press and hold this key to increase the value.

key: One press decreases the value by 1.

Press and hold this key to decrease the value.

Note that the SV (SV0) will be registered in 3 seconds without any operation. (Refer to P.12) When changed the parameters “P-n2”, “ALM1” or “ALM2”, turn the power OFF and ON.

SEL

key, the displayed values are registered.

2-3 Parameter functions and method of settings

Method of setting the SV (Setting value) [Description]

• The SV is a target value for control.

• Any SV that is outside of the range set in the parameters

of (lower limit) and (upper limit) of the third block cannot be set. (See page 50.)

[Setting example] Changing the SV from 250.0°C to 348.7°C

Display Operating procedure

Related parameters: (page 50)

(page 50)

PV indication SV indication

Press the key to display the SV. (SV lamp is lit.)

Press the or keys to display .

will be registered in the SV (front SV) in three seconds. After that, the controller will

operate with the SV being .

SEL

q First block parameters

Standby setting (Settings: oFF/on)

[Description]

• This parameter switches the control between RUN and Standby.

• During standb y, the control output and the alarm output stay OFF, like the standby for ramp-soak operation. Retransmission output is kept operated. (Howev er, if the type of retransmission output is set to the MV, it becomes 4mA or lower.)

• While the alarm with a hold is selected, the hold function takes effect after changing the Standby setting from ON to OFF.

• is displayed during the standby for ramp-soak operations or the controller changes to the standby state in case of the occurrence of errors.

• The other operations are the same as those of the rampsoak standby.

• The setting of ON/OFF for standby is saved after poweroff.

• When the standby is set to ON during the auto-tuning, self-tuning, and ramp-soak operations, those operations will stop. (The PID constant will not be renewed.) Even through it is set to OFF later, the auto-tuning, self-tuning, and ramp-soak operations will not be re-started.

• During standby, the ON-delay timer is reset. When returning to RUN from the standby state, the timer will start from the beginning.

• The SV lamp flickers only when standby state.

[Setting example] Starting the control

Display Operating procedure

PV indication

SV indication

PV indication

Press and hold the key for one second.

will be displayed.

Press the key once.

The current setting ( ) will be displayed.

Press the or keys to flicker and to display .

Press the key once. The standby state for control is selected. (control output and all the alarm

outputs: OFF) (Repeat the procedure from 2 to 4 to check the set value.)

If you want to display the operation status, press and hold the key for two seconds. The value

on the SV display will flash, indicating the standby status.

If unoperated state continues, the PV will be displayed.

SEL

Ramp-soak control (Settings: oFF/rUn/hLd) (Option)

[Description]

• This function automatically changes the SV (Setting value) according to the program pattern set in advance as shown in the right line graph. Up to eight pairs of rampsoak operation can be programmed.

• The first ramp starts at the PV (Measured value) that is the one just before running the program.

• The program can also automatically run at power-on (Power-on starting function). Refer to the parameter of

(page 46).

Related parameters:

(page 46) to (page 46)

to (page 46)

to (page 46) (page 46) (page 45)

Up to SV-8

SV-3 SV-2 SV-1

SV-4

First ramp

TM1r

Ramp: the section in which the SV changes toward the target value. Soak: the section in which the SV is the target value, and remains unchanged.

First soak

TM1S

Second soak

Second ramp

TM2S

TM2r

Third soak

Third ramp

Fourth ramp

TM3S

TM3r TM4r

Fourth soak

TM4S

Up to TM8r

Up to TM8s

[Setting example] Starting the ramp-soak operation

Display Operating procedure

PV indication

SV indication

PV indication

Press and hold the key for one second.

will be displayed.

Press the key to display .

Press the key once.

SEL

The current setting ( ) is displayed.

Pressing the or keys, the display flickers and is displayed.

Press the key once. Then, the program will start according to the ramp-soak pattern that is

SEL

set in advance.

(Repeat the procedure from 3 to 5 to check the set value.)

If you want to display the operation status, press and hold the key for two seconds.

The SV is displayed on the display area.

If unoperated state continues, the PV will be displayed.

SEL

*1) When the program was not set, it is turned to .

Canceling the alarm latch (Setting range: 0/1) (Option)

[Description]

• This parameter cancels the alarm latch when it is latching.

Related parameters:

[Setting example] Opening up the alarm latch

Display Operating procedure

to (page 54)

PV indication

SV indication

PV indication

Press and hold the key for one second.

will be displayed.

Press the key to display .

Press the key once.

The current setting ( ) is displayed.

Pressing the or keys to flicker and to display .

Press the key once.

(Repeat the procedure from 3 to 5 to check the set value.)

If you want to display the operation status, press and hold the key for two seconds.

The SV is displayed on the display area.

If unoperated state continues, the PV will be displayed.

SEL

Auto-tuning function (Settings: 0/1/2)

[Description]

[Note]

If the controller is powered off during auto-tuning, this makes the auto-tuning ineffectiv e with each parameter of , , and unchanged. To start the auto-tuning operation, set to “1” or “2” again.

• To suspend the auto-tuning, set to “0”. This makes the auto-tuning cancel with each parameter of , , and

unchanged.

• Once the parameters of , , and are set automatically by the auto-tuning, those parameters are stored in the controller even after it is power ed of f. Therefore, it is not necessary to execute the auto-tuning again.

• By setting to “1” or “2” , the auto-tuning operation starts, and at the end of the tuning, will be displayed automatically to .

• After the auto-tuning operation, the controller starts to operate at the automatically set values of , , and .

• A decimal point at the right end of the SV display flashes during auto-tuning.

• There are two codes for AT: Setting code [1]: SV standard type

Performs the auto-tuning based on the SV.

Setting code [2]: Low PV type

Performs the auto-tuning based on the SV-10%FS.

[Note]

Since ON/OFF control is performed during auto-tuning, overshoot against the SV may occur. To reduce the overshoot, execute the auto-tuning operation with the setting code [2] (Low PV) selected.

• The auto-tuning can be executed both just after power-on and in a control or stable status.

Related parameters:

(page 20) (page 21) (page 22)

(page 26)

(page 24)

[Setting example] Setting the auto-tuning operation to 1

Display Operating procedure

PV indication

SV indication

Press and hold the key for one second.

will be displayed.

Press the key to display .

Press the key once.

The current setting ( ) is displayed.

Press the or keys to flicker the display and to display .

Press the key once. is displayed and the auto-tuning will start. During auto-tuning,

a decimal point at the first digit from the right end of the display flickers.

(Repeat the procedure from 3 to 5 to check the set value.)

When the auto-tuning finishes properly, a decimal point stops flashing, and the set values of , ,

and parameters change. When the auto-tuning finishes abnormally, a decimal point stops flashing, but the set values of , , and parameters remain unchanged.

If you want to display the operation status, press and hold the key for two seconds.

The SV is displayed on the display area.

SEL

PV indication

If unoperated state continues, the PV will be displayed.

Displaying ON-delay alarm or the remaining time of timers (unit: seconds) (Option)

[Description]

• These parameters display the remaining time of Timers 1 and 2.

• The remaining time of the ON/OFF-delay timer is counted down. When the counter shows , the alarm relay is closed.

• During count-down, if the PV changes to the value of the temperature at which the alarm is set to OFF, or if “DI” for the timer is set to OFF, the counter is reset, and the alarm relay is opened.

•

， display parameter

SEL SEL

[Setting example] Displaying ON-delay alarm or the remaining time of timers

Display Operating procedure

PV indication

SV indication

PV indication

Press and hold the key for one second.

will be displayed.

Press the key to display . By pressing the key,

the remaining time (10 seconds) of the timer 1 will be displayed. Pressing the key again, it returns to display.

Press the key to display . By pressing the key, the remaining time (8 seconds)

of the timer 2 will be displayed. Pressing the key again, it returns to display.

If you want to display the operation status, press and hold the key for two seconds.

The SV is displayed on the display area.

If unoperated state continues, the PV will be displayed.

SEL

[Description]

Setting alarm 1 and 2 Upper limit of alarm 1

and 2 Lower limit of alarm 1

and 2

(Setting range:

Absolute value alarm: 0 to 100%FS Deviation value alarm: -100 to 100%FS )

}

(Option)

• These parameters are used to for settings of alarm 1 and 2.

• When the alarm type ( or alarms 1 and 2 ( and ) can be set.

• When the alarm type ( or ) is set to any value other than 0 to 15, the upper and lower limits of alarm 1 and 2 ( , , , ) can be set.

[Setting example] Setting the operation value of alarm 2 to -10°C

Display Operating procedure

PV indication

Press and hold the key for one second.

will be displayed.

Press the key to display .

Press the key once.

The current setting ( ) will be displayed.

Press the or keys to flicker and to display .

SEL

) is set to 0 to 15,

SEL

[Note]

Setting codes (12 to 15) cannot be selected in alarm type 1 ( ).

Related parameters: ,

, , ,

(page 42) (page 53) (page 51) (page 54)

SV indication

PV indication

Press the key once. will be displayed and the operation value -10°C will be registered

for . After that, the controller will operate with the operation value of = -10°C.

(Repeat the procedure from 3 to 5 to check the set value.)

If you want to display the operation status, press and hold the key for two seconds.

The SV will be displayed on the display area.

If unoperated state continues, the PV will be displayed.

SEL

Key lock (Setting range: 0

−

[Description]

• This parameter makes the set values of parameters unchangeable. However, the parameter name and the set values can be displayed.

• To reset the key lock, change to .

• Even when the key lock is set, control and alarm functions

can operate properly.

• There are six levels of the key lock:

[Setting example] Setting the key lock to “2”

Display Operating procedure

: Unlocked (reset) : All settings are unchangeable from the controller, but

changeable via communication.

: Only the SV is changeable from the controller, and all

settings are changeable via communication.

: All settings are changeable from the controller, but

unchangeable via communication.

All settings are unchangeable from the controller or via communication.

: Only the SV is changeable from the controller, but all

settings are unchangeable via communication.

PV indication

SV indication

PV indication

Press and hold the key for one second.

will be displayed.

Press the key to display .

Press the key once.

The current setting ( ) will be displayed.

Press the or keys to flicker and to display .

Press the key once. will be displayed and "2" will be registered for . After that,

any setting other than the SV cannot be changed from the front panel.

(Repeat the procedure from 3 to 5 to check the set value.)

If you want to display the operation status, press and hold the key for two seconds.

The SV will be displayed on the display area.

If unoperated state continues, the PV will be displayed.

SEL

w Second block parameters

Proportional band (Setting range: 0.0 to 999.9% of the measured range)

[Description]

• To select the ON/OFF control (two-position control), set to 0.0. It is not necessary to set and .

• can be automatically set by the auto-tuning operation.

• When is too small, control will be unstable, and when is too large, the response will be delayed.

[Setting example] Changing the proportional band from 5.0% to 15.0%

Display Operating procedure

• Set the hysteresis of the ON/OFF control (two-position control) in the parameter

• If auto-tuning is run after the ON/OFF control is selected, the ON/OFF control changes to the PID control. To keep the ON/OFF control selected, do not execute the autotuning.

Related parameters: (page 23)

(page 32)

PV indication

SV indication

PV indication

Press and hold the key for three seconds.

will be displayed.

Press the key once.

The current setting ( ) will be displayed.

Press the or keys to flicker and to display .

Press the key once. will be displayed and the 15.0% will be registered for . After that,

the controller will operate with being 15.0%. (Repeat the procedure from 2 to 4 to check the set value.)

If you want to display the operation status, press and hold the key for two seconds.

The SV will be displayed on the display area.

If unoperated state continues, the PV will be displayed.

SEL

Integral time (Setting range: 0 to 3200 seconds)

[Description]

• can be set automatically by the auto-tuning operation.

• can also be set manually.

• When is set to 0, the integral operation does not start.

• When is set to 0.0, this makes the setting of ineffec-

tive.

[Setting example] Changing the integral time from 240 seconds to 600 seconds

Display Operating procedure

PV indication

SV indication

PV indication

Press and hold the key for three seconds.

will be displayed.

Press the key to display .

Press the key once.

The current setting ( ) will be displayed.

Press the or keys to flicker and to display .

Press the key once. will stop flashing and will be registered for . After that, the

controller will operate with being seconds.

(Repeat the procedure from 3 to 5 to check the set value.)

If you want to display the operation status, press and hold the key for two seconds.

The SV will be displayed on the display area.

If unoperated state continues, the PV will be displayed.

SEL

Derivative time (Setting range: 0.0 to 999.9 seconds)

[Description]

• can be set automatically by the auto-tuning operation.

• can also be set manually.

• When is set to 0, the differential operation does not start.

• When is set to 0.0, this makes the setting of ineffective.

[Setting example] Changing the differential time from 60.0 seconds to 50.0 seconds

Display Operating procedure

PV indication

SV indication

PV indication

Press and hold the key for three seconds.

will be displayed.

Press the key to display .

Press the key once.

The current setting ( ) will be displayed.

Press the or keys to flicker and to display .

Press the key once. will be displayed and 50.0 seconds will be registered for . After that,

the controller will operate with being 50.0 seconds.

(Repeat the procedure from 3 to 5 to check the set value.)

If you want to display the operation status, press and hold the key for two seconds.

The SV will be displayed on the display area.

If unoperated state continues, the PV will be displayed.

SEL

Hysteresis range for ON/OFF control (Setting range: 0 to 50%FS)

[Description]

• To select the ON/OFF control (two-position control), set to 0.0. It is not necessary to set and .

• When the hysteresis range (Range of ON/OFF control) is

too small, the output may switch the ON/OFF frequently . (This may affect the life of the device to be controlled, especially when contact output is selected.)

• The unit of the set value of this parameter is ºC or ºF

(engineering unit). The setting range varies according to the measured range of input.

[Ex] Input Thermocouple K :At measured range of 0

Resistance bulb :At measured range of 0

Related parameters:

[Setting example] Changing the hysteresis range from 1˚C to 35˚C

Display Operating procedure

to 400 ºC, the setting range is 0 to 200 ºC.

to 150 ºC, the setting range is 0 to 75 ºC.

(page 20)

(page 32)

PV indication

SV indication

PV indication

Press and hold the key for three seconds.

will be displayed.

Press the key to display .

Press the key once.

The current setting ( ) will be displayed.

Press the or keys to flicker and to display .

Press the key once. will be displayed and 35˚C will be registered for . After that,

the controller will operate with the being 35˚C.

(Repeat the procedure from 3 to 5 to check the set value.)

If you want to display the operation status, press and hold the key for two seconds.

The SV will be displayed on the display area.

If unoperated state continues, the PV will be displayed.

SEL

+ 51 hidden pages

CaptiveAire PXR3 Installation Manual

Table of Contents

Part Names and Functions

Operations

2-1 Parameter list

2-2 Basic operations

2-3 Parameter functions and method of settings