Canon WFT-E2 II A User Manual

Wireless File Transmitter

COPY

WFT-E2 II

Instruction Manual for Use With EOS-1D Mark IV

To EOS-1D Mark III or EOS-1Ds Mark III Users

This instruction manual describes the use of the transmitter when connected to the EOS-1D Mark IV. When using the transmitter with the EOS-1D Mark III or EOS-1Ds Mark III, refer to the PDF manual in the EOS_1DIII_1DsIII folder.

To comply with local radio wave regulations, Canon offers four region-specific versions of the transmitter (WFT-E2 IIA, E2 IIB, E2 IIC, and E2 IID) in various areas around the world (p.8). For convenience, we refer to the product in this manual simply as “the transmitter,” without reference to versions A, B, C, or D.

INSTRUCTION MANUAL

Introduction

COPY

The Wireless File Transmitter WFT-E2 II is an accessory for EOS-1D Mark IV camera. It gives the camera wireless and wired LAN functionality and adds a USB port, enabling the following operations.

Wireless and Wired LAN Functions

FTP Transfer

Transfer images to an FTP server

EOS Utility

Use EOS Utility to capture, view, and

download images remotely

WFT Server

Use a web browser to capture, view,

and download images remotely

Linked Shooting

Wirelessly trigger shooting by slave cameras linked to a master camera

Functions When Connected via USB

COPY

External Media

Record or backup images onto external media

GPS

Connected by a USB cable Connected via Bluetooth

Add the latitude, longitude, altitude, date and time, and other shooting information to images

Introduction

Conventions Used in this Manual

COPY

These instructions should be followed only after your wireless or wired LAN and FTP server

settings are complete. For details on configuring these settings, refer to the documentation provided with the respective equipment.

Terms in brackets [ ] indicate button or icon names or other software elements. Brackets

also denote camera menu items.

Page numbers in parentheses indicate where you can find additional information. Instructions on camera operations should be followed only after you have read the Camera

Instruction Manual and are familiar with operating the camera.

Sections of this manual labeled with the following symbols contain information of the

corresponding nature.

: Warnings to avoid potential problems are labeled with a caution symbol.

: Supplemental information is labeled with a note symbol.

Windows is a trademark or registered trademark of Microsoft Corporation in the United

States and other countries.

Macintosh is a registered trademark of Apple Corporation in the United States and other

countries.

Wi-Fi is a registered trademark of the Wi-Fi Alliance. Wi-Fi Certified, WPA, WPA2, and the Wi-Fi Certified logo are trademarks of the Wi-Fi

Alliance.

WPS as used on camera settings screens and in this manual signifies Wi-Fi Protected

Setup.

UPnP is a trademark of the UPnP Implementers Corporation. Bluetooth and the Bluetooth logos are trademarks owned by Bluetooth SIG, Inc. All other corporate and brand names in this manual are trademarks or registered

trademarks of their respective owners.

Using the transmitter for remote image transfer, capture, or viewing requires adequate knowledge of configuring your wireless or wired LAN and FTP server. Canon cannot provide support for configuring wireless or wired LANs or FTP servers. Note that Canon cannot be held liable for any loss or damage to the transmitter from erroneous network or FTP server settings. In addition, Canon cannot be held liable for any other loss or damage caused by use of the transmitter.

Chapter List

COPY

Introduction

Basic Network Settings

Transferring Images to an FTP Server

Remote Capture Using EOS Utility

Remote Capture Using WFT Server

Linked Shooting

Managing Settings Information

Using External Media

Using GPS Devices

Troubleshooting

Reference

109

COPY

Introduction 2

Conventions Used in this Manual ...................................................................................................... 4

Chapter List........................................................................................................................................ 5

Contents............................................................................................................................................. 6

Areas of Use and Restrictions ........................................................................................................... 8

Safety Warnings............................................................................................................................... 10

Nomenclature................................................................................................................................... 11

Attaching to the Camera .................................................................................................................. 12

Subsequent Organization of This Manual........................................................................................ 13

1 Basic Network Settings 15

Getting Ready.................................................................................................................................. 16

Displaying the Connection Wizard................................................................................................... 17

Selecting the Communication Method and LAN Type ..................................................................... 18

Using the Wizard to Establish a Connection.................................................................................... 21

WPS Connections (PBC Mode)....................................................................................................... 23

WPS Connections (PIN Mode) ........................................................................................................ 24

Configuring Network Settings .......................................................................................................... 25

2 Transferring Images to an FTP Server 29

Configuring FTP Communication Settings....................................................................................... 30

Automatic Image Transfer After Each Shot ..................................................................................... 32

Transferring Images Individually ...................................................................................................... 34

Batch Transfer ................................................................................................................................. 36

Checking Image Transfer History .................................................................................................... 40

Viewing Transferred Images............................................................................................................ 41

3 Remote Capture Using EOS Utility 43

Configuring EOS Utility Communication Settings ............................................................................ 44

Using EOS Utility ............................................................................................................................. 47

4 Remote Capture Using WFT Server 49

Configuring WFT Server Communication Settings .......................................................................... 50

Displaying WFT Server .................................................................................................................... 52

Viewing Images................................................................................................................................ 53

Remote Capture [Camera control] ................................................................................................... 55

Remote Capture [Simple control]..................................................................................................... 58

Remote Capture............................................................................................................................... 59

5 Linked Shooting 61

Setting Up Linked Shooting ............................................................................................................. 62

Arranging the Slave Cameras .......................................................................................................... 64

Contents

COPY

6 Managing Settings Information 65

Checking Settings ............................................................................................................................ 66

Changing Settings............................................................................................................................ 67

Saving and Loading Settings........................................................................................................... 69

7 Using External Media 71

Connecting External Media.............................................................................................................. 72

Choosing Recording Media When Shooting.................................................................................... 75

Copying Images ............................................................................................................................... 77

Backing Up on External Media......................................................................................................... 78

8 Using GPS Devices 83

Connecting GPS Devices with a USB Cable ................................................................................... 84

Connecting GPS Devices via Bluetooth........................................................................................... 87

9 Troubleshooting 91

Responding to Error Messages ....................................................................................................... 92

Wireless LAN Notes ....................................................................................................................... 106

Checking Network Settings ............................................................................................................ 107

10 Reference 109

Creating and Registering Captions ................................................................................................ 110

Specifications................................................................................................................................. 111

Index .............................................................................................................................................. 118

Areas of Use and Restrictions

COPY

To comply with local radio wave regulations in various areas around the world, Canon offers

four region-specific versions of the transmitter (WFT-E2 IIA, E2 IIB, E2 IIC, and E2 IID) as described below. Please do not use your model (version) of transmitter in regions it was not designed for. For information on other areas where the transmitter can be used, contact Canon Service Center.

Model

(Version)

WFT-E2 IIA United States, Canada, Singapore, and Hong Kong

Japan, France, Italy, Germany, United Kingdom, Belgium,

the Netherlands, Luxembourg, Ireland, Denmark, Greece,

WFT-E2 IIB

WFT-E2 IIC Mainland China and Hong Kong

WFT-E2 IID Can be used in all areas noted above

Spain, Portugal, Austria, Finland, Sweden, Poland, Hungary,

Romania, Bulgaria, Czech Republic, Slovakia, Slovenia,

Estonia, Latvia, Lithuania, Cyprus, Malta, Iceland, Norway,

Switzerland, Liechtenstein, Australia, New Zealand, Russia,

and Hong Kong

Area of Use

In France, outdoor use is prohibited. In mainland China, outdoor use requires a permit in some areas.

IEEE 802.11a Restrictions

When IEEE 802.11a wireless networking is used, channels in gray in the following table cannot be used. These restrictions are established by local regulations, which must be upheld. The transmitter can be used on channels in blue. Regarding channels in yellow, some restrictions apply. Refer to the footnotes.

Wireless LAN

Connection Method

WFT-E2 IIA

Indoors

Outdoors

Indoors

WFT-E2 IIB

Outdoors

WFT-E2 IIC

*J: In Japan, outdoor use on channels 52 – 64 is prohibited.

*C: In mainland China, outdoor use requires a permit in some areas.

Infrastructure

Ad hoc

Infrastructure

Ad hoc

Infrastructure

Ad hoc

Infrastructure

Ad hoc

36 – 48 52 – 64 149 – 165

36 – 48 52 – 64 100 – 140

36 – 48

36 – 48 52 – 64 100 – 140

149 – 161*

Wireless LAN Specification

and Supported Channels

IEEE 802.11a

IEEE 802.11b/g 1 – 11 ch

IEEE 802.11a

IEEE 802.11b/g 1 – 13 ch

IEEE 802.11a 149 – 161 ch

IEEE 802.11b/g 1 – 13 ch

IEEE 802.11a Not supported

IEEE 802.11b/g 1 – 11 ch

Channel

52 – 64*

36 – 64 ch

149 – 165 ch

36 – 64 ch

100 – 140 ch

100 – 140

Areas of Use and Restrictions

COPY

The following actions may be punishable under law. Disassembling or modifying the

transmitter, or removing the certification label on it.

Do not use the transmitter near other devices that emit radio waves, such as medical

equipment or electronic devices. The transmitter may interfere with operation of these devices.

Use the transmitter only with a compatible EOS DIGITAL camera. Using it with incompatible

cameras may cause malfunction, accidents, and other problems not covered under warranty.

Use the transmitter as a wireless or wired LAN device as described in this instruction

manual. If you use the transmitter for any other purpose, Canon cannot be held liable for any loss or damage that may occur.

Safety Warnings

COPY

The following precautions are intended to prevent harm to you and others as well as damage to equipment. Become familiar with the precautions before using the transmitter to ensure correct and safe operation.

Warning Preventing Serious Injury or Death

To prevent fire, excessive heat, chemical leakage, or explosion, follow these safety guidelines.

• Do not insert metallic objects between electrical contacts of the transmitter, accessories, or connecting cables.

Do not use the transmitter where there is flammable gas. There is a risk of explosion or fire. If the transmitter is dropped and internal parts are exposed, do not touch the exposed parts. There is a risk of

electrical shock.

Do not disassemble or modify the transmitter. High-voltage internal parts may cause electrical shock. Do not store the transmitter in dusty or humid places. There is a risk of fire or electrical shock. Before using the transmitter on board airplanes or in hospitals, make sure use is permitted. Electromagnetic

waves emitted by the transmitter may interfere with instrumentation or medical equipment.

Caution Preventing Injury or Equipment Damage

Do not leave the transmitter inside a vehicle in hot weather or near a heat source. The transmitter may become

hot and cause burns if touched.

Do not cover or wrap the transmitter with a cloth. This may trap heat inside, posing a risk of case deformation or

fire.

Do not use paint thinner, benzene, or other organic solvents to clean the transmitter. This poses a risk of fire and

may be hazardous to your health.

If the product malfunctions, becomes damaged, or requires repair, contact your dealer or the nearest Canon Service Center.

Handling Precautions

The transmitter is a precision instrument. Do not drop it or subject it to shock. The transmitter is not waterproof. Do not use it underwater. Wipe off any moisture with a clean, dry cloth. If the transmitter has been exposed to salty air,

wipe it with a clean damp cloth after wringing it out to remove excess water.

Never leave the transmitter near any equipment that generates a strong magnetic field,

such as magnets or electric motors.

Do not leave the transmitter in excessive heat, such as in a vehicle in direct sunlight. High

temperature may damage the transmitter.

Do not wipe the transmitter using cleaners containing organic solvents. If the transmitter

becomes difficult to clean, take it to the nearest Canon Service Center.

To avoid corrosion, do not store the transmitter where there are strong chemicals, such as in

darkrooms or chemical labs.

Nomenclature

COPY

Locking lever

USB port

Ethernet

RJ-45 port

Port cover

Terminal cap receptacle (Not used with the EOS-1D Mark IV)

Transmitter Case

External Media Case*

USB

> USB lamp

LAN

> Network lamp

Attachment pin

Tightening screw Terminal

Waterproof/Dustproof USB Cap*

*1: For storing portable hard disks or other devices. *2: Attach this cap before connecting the USB cable in rainy weather or under other adverse conditions.

Attaching to the Camera

COPY

Turn off the camera before attaching the transmitter.

Ensure the camera battery has sufficient charge. If the charge drops below 19%, you cannot transfer captured images or back them up to external media.

Open the terminal cover on the camera.

Open the extension system terminal cover and

turn it toward the bottom.

Move the lever into the release position.

Attach the transmitter.

Align the attachment pin with the WFT-E2 II/IIA

mounting hole on the camera.

Push the terminal firmly into the camera. As you push the terminal into the camera, turn the

tightening screw until it stops rotating to attach the transmitter securely.

Move the lever into the locked position.

The transmitter is now attached to the camera. The transmitter will be powered by the camera.

Removal

Turn off the camera. Push the lever down, into the release position. Loosen the tightening screw until it spins freely. Pull the terminal out of the camera.

Subsequent Organization of This Manual

COPY

Click one of the following chapter titles to view the corresponding page.

1 Basic Network Settings (p.15)

2 Transferring Images to an FTP Server (p.29)

3 Remote Capture Using EOS Utility (p.43)

4 Remote Capture Using WFT Server (p.49)

5 Linked Shooting (p.61)

6 Managing Settings Information (p.65)

7 Using External Media (p.71)

8 Using GPS Devices (p.83)

COPY

Basic Network Settings

COPY

Complete the basic network settings by following transmitter connection

instructions on the camera menu screen.

Getting Ready

COPY

[FTP trans.], [EOSUtility], [WFTserver]

The connection instructions help you follow the steps to connect the transmitter to an existing wireless or wired LAN. To connect to a wireless LAN, prepare the wireless LAN terminal (wireless LAN access point or wireless LAN adapter) and computer in advance so that they are ready for you to connect the transmitter to the wireless network. When configuring the basic network settings, bring the transmitter within 3 m / 9.8 ft. of the wireless LAN terminal. To connect to a wired LAN, use a LAN cable to connect the transmitter and computer. Set the transmitter for connection to the wired network.

Wireless Transmission of Movie

Individual movie files are large, and wireless file transmission takes some time. When setting up an environment for stable transmission to the wireless LAN terminal, refer to the information on page 106.

[LinkedShot]

Set up two or more EOS-1D Mark IV cameras with attached transmitters.

Displaying the Connection Wizard

COPY

This section describes the process of following the connection instructions. If an error is displayed, refer to “Troubleshooting” in Chapter 9 (p.91) and check the settings.

Pressing the shutter button or other camera controls during configuration by the connection

instructions will close the connection instructions. Do not press the shutter button or other controls until configuration is finished.

On the [5] tab, set [Auto power off] to [Off]. If auto power off is activated, the connection

instructions will be closed during the configuration process.

Turn the camera on.

Display the transmitter menu.

On the camera, press the <7> button. On the [7] tab, select [WFT settings] and press

<0>. [WFT settings] is added to the tab after you attach the transmitter.

Select [Connection wizard].

X The [Select communication method] screen is

displayed.

X The <

LAN

> lamp starts blinking.

Selecting the Communication Method and LAN Type

COPY

Selecting the Communication Method

Turn the <5> dial to select the communication

method, and then press <0>.

Select [OK] and press <0> to go to the next

screen.

• FTP trans.

Choose this option to transfer captured images to an FTP server. Images can be automatically transferred as you shoot them, or you can select images to be transfered later.

Computer Operating Systems

Operation via [FTP trans.] requires that Windows Vista (Business, Enterprise, or Ultimate Edition for 32- or 64-bit systems), Windows XP Professional, Windows 2000, or Mac OS X

10.4 or 10.5 be installed on your computer. In addition, the computer must be set up as an FTP server in advance. For instructions on setting up your computer as an FTP server, refer to the computer documentation.

Windows Vista Home Premium and Home Basic Edition as well as Windows XP Home Edition cannot be used because FTP server functionality is not supported.

• EOSUtility

Choose this option for remote capture over a wireless or wired LAN using the EOS Utility software included with your camera. In addition to remote capture, all camera operations in EOS Utility are supported. With this option, a wireless or wired network is used instead of the USB cable.

Requires a computer with EOS Utility (included with EOS-1D Mark IV cameras) installed.

Selecting the Communication Method and LAN Type

COPY

• WFTserver

Choose this option for remote capture over a wireless or wired LAN with the transmitter acting as a server. Additionally, images on a memory card in the camera can be viewed and downloaded to a computer. The camera can be accessed like browsing a webpage, by users at up to three computers.

Computer Operating Systems

Any computer with a web browser can be used, regardless of the operating system. Even devices other than computers can be used, if they feature a web browser. However, if the web browser does not support JavaScript, WFT Server functions will be limited. Also note that devices with limited performance may display images more slowly, and downloading images to these devices may not be possible.

• LinkedShot

Choose this option for linked shooting with multiple EOS-1D Mark IV cameras attached with transmitters. Up to 10 slave cameras can be linked to the master camera on which you will release the shutter. Note that there will be a slight delay after you release the master camera shutter before the slave cameras shoot. Movie shooting is not supported.

For further instructions on [LinkedShot], refer to page 61 of this manual.

Selecting the Communication Method and LAN Type

COPY

Selecting the LAN Type

For [LinkedShot] instructions, refer to page 61. Note that no information about [LinkedShot] is given in this chapter.

Turn the <5> dial to select the type of LAN, and

then press <0>.

Select [OK] and press <0> to go to the next

screen.

Wireless LAN

The [Wireless LAN setup method] screen is displayed.

[Connect with wizard]: See p.21 [WPS (PBC mode)]: See p.23 [WPS (PIN mode)]: See p.24

Select [WPS (PBC mode)] or [WPS (PIN mode)] when using a wireless LAN terminal compatible with Wi-Fi Protected Setup (WPS).

Wired LAN

The [Network] settings screen is displayed. If you have selected a wired network, refer to page 25, “Configuring Network Settings.” Use a Category 5 or higher STP LAN cable. (STP: Shielded Twisted Pair)

Using the Wizard to Establish a Connection

123 4

COPY

Selecting the Wireless Network

When you select [Connect with wizard], active wireless LAN terminals in your area are listed, accompanied by information about them. Select the SSID (or ESS-ID) of your desired wireless LAN terminal.

Select [Connect with wizard].

Turn the <5> dial to select [Connect with

wizard], and then press <0>.

Select the wireless LAN terminal.

To select the wireless LAN terminal, press <0>. Turn the <5> dial to select the wireless LAN

terminal, and then press <0>.

Select [OK] and press <0> to go to the next

screen.

1 Indicates whether the device is in infrastructure or ad hoc mode 2 An icon is displayed if the wireless LAN terminal is encrypting communication 3 Indicates the first 9 characters of the SSID 4 Indicates the channel used

Encryption by Wireless LAN Terminals

If the wireless LAN terminal is encrypting communication, select the corresponding method in [Authentication] and [Encryption].

[Authentication]: Open system, Shared key, WPA-PSK, or WPA2-PSK [Encryption]: WEP, TKIP, or AES

[Enter connection] and [Search again]

To configure settings for the wireless LAN terminal manually, select [Enter connection] and

press <0>. Complete the settings for the items displayed, one after another.

To search for wireless LAN terminals again, select [Search again] and press <0>.

Using the Wizard to Establish a Connection

COPY

Entering the Wireless LAN Encryption Key

Next, enter the encryption key of the wireless LAN terminal. For details on the encryption key, refer to the device’s instruction manual. Note that the screens displayed in steps 1 to 3 below vary depending on the authentication and encryption of the wireless LAN terminal.

The [Key index] screen is displayed only if WEP

encryption is used by the wireless LAN terminal.

Turn the <5> dial to select the key index number

specified as the access point, and then press <0>.

Select [OK] and press <0> to go to the next

screen.

Turn the <5> dial to select the key format, and

then press <0>.

Select [OK] and press <0> to go to the next

screen.

Enter the encryption key. To switch between input areas, press the <H>

button.

To move the cursor, turn the <5> dial. In the bottom input area, turn the <5> dial and

press <0> to enter the encryption key.

If you make a mistake, press the <L> button to

erase it.

When you press the <7> button to complete

the connection with the wireless LAN terminal, the [Network] screen (p.25) is displayed.

To return to the previous screen, press the

<6> button. The entry is erased.

WPS Connections (PBC Mode)

COPY

This is a connection mode when using a wireless LAN terminal compatible with Wi-Fi Protected Setup (WPS). Pushbutton Connection mode (PBC mode) makes it easy to establish a connection between the camera and the wireless LAN terminal by pressing the WPS button on the wireless LAN terminal. Note that if multiple wireless LAN terminals are active in your area, it may be harder to establish a connection. In this case, try using [WPS (PIN mode)] to establish a connection. Confirm the position of the WPS button on the wireless LAN terminal in advance. It may take about one minute to establish connection.

Connection may not be possible if stealth functions are enabled on the wireless LAN terminal. Deactivate stealth functions.

Select [WPS (PBC mode)].

Turn the <5> dial to select [WPS (PBC mode)],

and then press <0>.

Select [OK] and press <0> to go to the next

screen.

Establish a connection with the wireless LAN terminal.

Press the WPS button on the wireless LAN

terminal. For details about where the button is located and how long to press it, refer to the instruction manual of the wireless LAN terminal.

Select [OK] and press <0> to establish a

connection with the wireless LAN terminal.

When the connection with the wireless LAN

terminal is established, the [Network] screen (p.25) is displayed.

WPS Connections (PIN Mode)

COPY

This is a connection mode when using a wireless LAN terminal compatible with Wi-Fi Protected Setup (WPS). In PIN code connection mode (PIN mode), an 8-digit identification number specified on the camera is set on the wireless LAN terminal to establish a connection. Even if there are multiple wireless LAN terminals active in your area, this is a relatively reliable method of establishing a connection using a shared identification number. It may take about one minute to establish connection.

Connection may not be possible if stealth functions are enabled on the wireless LAN terminal. Deactivate stealth functions.

Select [WPS (PIN mode)].

Turn the <5> dial to select [WPS (PIN mode)],

and then press <0>.

Select [OK] and press <0> to go to the next

screen.

Specify the PIN code on the wireless LAN terminal.

On the wireless LAN terminal, specify the 8-digit

PIN code shown on camera LCD monitor.

For instructions on setting PIN codes on the

wireless LAN terminal, refer to the instruction manual of the wireless LAN terminal.

Select [OK] and press <0> to display the

confirmation screen.

Establish a connection with the wireless LAN terminal.

Select [OK] and press <0> to establish a

connection with the wireless LAN terminal.

When the connection with the wireless LAN

terminal is established, the [Network] screen (p.25) is displayed.

Configuring Network Settings

COPY

Turn the <5> dial to select how to configure the

network settings, and then press <0>.

Select [OK] and press <0> to go to the next

screen.

[Auto setting]

Settings otherwise configured with [Manual setting] can be configured automatically.

However, the IP address and similar settings must be automatically assigned and configured in environments using DHCP servers or wireless LAN terminals or routers supporting DHCP server functions. If an error is displayed, select [Manual setting] regardless of whether the IP address and similar settings are automatically assigned and configured.

[Manual setting]

The [IP address set.] screen is displayed after you select [Manual setting]. If [Auto setting] results in an error, enter the IP address manually. As the IP address, enter the IP address assigned to the camera. Enter the [IP address], [Subnet mask], [Gateway], and [DNS address] on each screen as they are displayed. If you are not sure what to enter, refer to page 107, “Checking Network Settings,” or ask the network administrator or another person knowledgeable about the network.

When entering numbers for the IP address, subnet mask,

and so on, press <0> to move the input position and turn the <5> dial to enter the number.

Configuring Network Settings

COPY

Completing Settings for the Communication Method

The following instructions are for settings screens that vary depending on the communication method (FTP Transfer, EOS Utility, or WFT Server), as shown below. Read the page that introduces the selected communication method.

FTP trans.

Chapter 2 (p.29)

EOSUtility

Chapter 3 (p.43)

Windows Vista Users

Before performing the operations from page 43, perform the operations below. If these operations are not performed, the WFT Pairing Software described on page 44 may not start. Open the [C Drive]  [Program Files]  [Canon]  [EOS Utility]  [WFTPairing] folder (in this order), and then double-click the [WFT FirewallSettings] icon. After performing this operation, perform the operation on page 43.

WFTserver

Chapter 4 (p.49)

Configuring Network Settings

COPY

Virtual Keyboard Operation

The virtual keyboard is displayed during entry of the encryption key, server name, and other information.

Switching to other input areas

To switch between input areas, press the <H> button.

Moving the cursor

To move the cursor, turn the <5> dial. You can also move the cursor using <9>.

Entering text

In the bottom input area, turn the <5> dial to move the cursor and press <0> to enter text. You can also move the cursor using <9>.

Deleting text

If you make a mistake, press the <L> button to erase it.

Confirming entries

Press the <7> button to confirm what you have entered and go to the next screen.

Canceling entries

Press the <6> button to erase the entry and return to the previous screen.

COPY

Transferring Images

COPY

to an FTP Server

With FTP transfer, you can automatically transfer each image to the FTP

server as you shoot or transfer a set of shots together.

Configuring FTP Communication Settings

COPY

These instructions are continued from Chapter 1.

Turn the <5> dial to select [Address setting],

and then press <0>.

If you have set the DNS server setting to

[Disable], the screen at left is displayed.

Press <0> to select the input position, and then

turn the <5> dial to enter the IP address of the FTP server.

If you have set the DNS server IP address setting

to [Auto assign] or [Manual setting], the screen at left is displayed.

For instructions on screen operations, refer to

“Virtual Keyboard Operation” (p.27).

Enter the FTP server’s server name or IP address.

In [Port number setting], enter 00021, in most

cases.

Turn the <5> dial to select [OK], and then press

<0> to go to the next screen.

Complete the [Passive mode] settings. If an Error 41 (“Cannot connect to FTP server”) is

displayed in step 8, setting [Passive mode] to [Enable] may resolve it.

Complete the [Proxy server] settings. Turn the <5> dial to select [OK], and then press

<0> to go to the next screen.

+ 90 hidden pages