Canon VB-S805D Installation Guide
BIE-7095-000
ENGLISH
Plenum Mounting Kit SR30-P-VB
Installation Guide
This “Installation Guide” explains the installation method using
the Plenum Mounting Kit SR30-P-VB. Be sure to read the “Safety
Precautions” section for correct use. After reading this Installation
Guide, keep it in a readily accessible location for future reference.
This camera is for indoor use only.
In addition to this “Installation Guide”, please also read the
“Installation Guide” included with the camera.
Caution
Symbols Indicating Camera Model
Camera specific functions will be listed using the icons below.
: VB-S30D : VB-S31D : VB-S800D/VB-S805D
© CANON INC. 2016 Printed in Taiwan
Check Included Items
Plenum Mounting Unit Recessed Mounting Cover
Sticker
Screws (M4) x 3
Template
Installation Guide (This document)
Symbols Indicating Safety Precautions
This Installation Guide uses the following symbols to indicate
important information the user should know in order to use the
product safely. Explanations are provided for each symbol so that
users will understand the level of importance for each. Be sure to
observe these items.
Warning
Caution
Caution
Request a professional installer for all
installation work. Never try to install the
camera yourself. Doing so may result in
unforeseen accidents such as dropping
the camera or electric shock.
Failure to follow the instructions
accompanied by this symbol may result in
death or serious injury.
Failure to follow the instructions
accompanied by this symbol may result in
injury.
Failure to follow the instructions
accompanied by this symbol may result in
property damage.
Safety Precautions
Installation Precautions
Warning
Do not install in the following places:
• Places in direct sunlight, near heat-generating objects, or
subject to high temperatures
• Places near fire sources or flammable solvents (alcohol,
thinner, fuel, etc.)
• Humid or dusty places
• Places subject to oily smoke or steam
• Places subject to sea air
• Confined or enclosed places
Failure to do so may result in fire or electric shock.
Precautions for the LAN (power) cable:
• Do not set any heavy objects on the LAN cable.
Do not pull, forcibly bend, scratch, or modify the LAN cable.
•
Failure to do so may result in fire or electric shock.
Caution
For installation or inspection of this camera, consult the
dealer where you purchased the product.
• This installation should be made by a qualified service
person and should conform to all local codes.
• When installing, make sure the surface is capable
of withstanding the total weight of the camera and
accessories, and sufficiently reinforce if necessary.
• Periodically check the parts and screws for rust and
loosening, in order to prevent injuries and equipment
damage due to falling items.
• Do not install in unstable places, places subject to
significant vibration or impact, or places subject to salt
damage or corrosive gas.
• Be sure to attach the safety wire when installing th
camera.
• Use only with compatible cameras.
• If a ceiling plate thickness is not between 10.0 and
50.0 mm, do not use it.
Failure to do so may result in the camera falling or other
accidents.
• Do not touch the edges of metal parts with bare hands.
• Be careful not to get your fingers caught when installing.
Failure to do so may result in injuries.
Caution
• Do not turn the camera rotator by hand.
Do not install on an unstable surface. Also, make
•
sure the camera is installed less than ±5° off horizontal.
• After turning off the power, do not turn the power on again
for at least five seconds.
• Take measures to remove static electricity before
performing any procedures.
• If there is condensation, please wait to power on until the
condensation dissipates.
Failure to do so may result in malfunctions.
• Take care not to damage wiring or pipes.
Failure to do so may result in damage to peripheral items.
e
Precautions for Use
Warning
• If you discover defective conditions such as smoke,
strange sounds, heat or strange odors, immediately stop
using the camera and contact your nearest dealer.
Fire or electric shock may result from continued use of the product.
• If thunder starts, stop installation or inspection etc. and
do not touch the camera or continue connecting the
cable.
• Do not disassemble or modify the camera.
• Do not damage the connecting cable.
• Do not spray the camera with water, or otherwise make it
wet.
• Do not insert foreign objects such as water or metal into
the camera.
• Do not use flammable sprays near the camera.
• Do not leave LAN cables connected when the camera is
not in use for long periods.
• Do not use flammable solvents such as alcohol, paint
thinner or benzine when cleaning the camera.
Failure to do so may result in fire or electric shock.
Main Specifications
Model SR30-P-VB
Weight Approx. 900 g (1.99 lb.) (Plenum Mounting Unit, Recessed
TORX is the trademark of Acument Intellectual Properties,
LLC.
The contents of this guide are subject to change without any
prior notice.
Mounting Cover)
External Dimensions
136 (5.35)
158 (6.22)
166 (6.54)
76 (2.99)12 (0.47)
170 (6.09)
Before Installing the Camera
Perform camera settings by using the software on the
Setup CD-ROM (please refer to the “Operation Guide”).
Remove the tape affixed on the unit from the factory.
Attach the camera to the camera holder.
1
❷
❶
❸
2
3
a
a. Camera holder
4
M4 x 3
Screws
(included)
Unit : mm (in.)
Installing the Camera
c
5
8
10
1
a
a. Template
3
b
b. Safety wire (included with camera)
4
2
Note
Please take care when handling
the openings, as the edges may
be sharp and lead to an injury.
d. Long screw
6
Screw included
with the camera
❶
❷
❶
d
f
❸
Driver
Tightening torque:
0.7 N·m (max.)
f. Recessed mounting cover
g. TORX T20 Driver
❶
g
11
❶
❸
❷
h
❷
e
h. Sticker (included)
c
. LAN cable
Front
Front
Face the
camera forward
PAN angle
range
e. LAN cable
7
❷
Note
Please take care not
to pinch the rubber on
the safety wire, when
attaching the camera to
the Plenum Mounting Unit.
❶
Face the
camera
forward
9
Removing
❷
❶
❸
Loading...