Canon RF 15-35mm f/2.8L IS USM User manual
Instructions
ENG
Thank you for purchasing a Canon product.
Canon RF70-200mm F2.8 L IS USM is a
telephoto zoom lens for use with EOS R series
cameras.
z “IS” stands for Image Stabilizer.
z “USM” stands for Ultrasonic Motor.
Camera Firmware
Please use the latest version of firmware with the
camera in use. For details on whether the firmware is
the latest version or not, and for details on updating
the firmware, please check the Canon website.
Conventions used in these instructions
Warning to prevent lens or camera malfunction
or damage.
Supplementary notes on using the lens and
taking pictures.
ENG-1
Safety Precautions
Precautions to ensure that the camera is used
safely. Read these precautions thoroughly. Make
sure all details are observed in order to prevent
risks and injury to the user and other people.
Warning
Do not look directly at the sun or other strong
z
light sources through a lens. This may result in
loss of sight.
Do not leave a lens in the sun without the lens
z
cap attached. The lens may concentrate entering
sunlight and cause a malfunction or fire.
Details pertaining to risks that may
result in death or serious injury.
Details pertaining to risks that
Caution
Do not leave the product in places exposed to
z
extremely high or low temperatures. The product
may cause burns or injury when touched.
Do not insert your hand or fingers into the
z
product. This may result in injury.
When using a tripod, please use one that has
z
sufficient strength.
Make sure that the lock knob on the tripod
z
mount is firmly tightened.
may result in injury or damage to
other objects.
ENG-2
General Precautions
Handling Precautions
Do not leave the product in excessive heat such as
z
in a car in direct sunlight. High temperatures can
cause the product to malfunction.
If the lens is taken from a cold environment into a
z
warm one, condensation may develop on the lens
surface and internal parts. To prevent condensation
in this case, first put the lens into an airtight
plastic bag before taking it from a cold to warm
environment. Then take out the lens after it has
warmed gradually. Do the same when taking the
lens from a warm environment into a cold one.
The lens interior may appear to waver, but this
z
does not indicate a defect or failure, and will not
cause any problems in use.
Please also read any lens related handling
z
precautions listed in your camera’s instruction
manual.
ENG-3
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
Do not make any changes or modifications to the equipment
unless otherwise specified in the instructions. If such
changes or modifications should be made, you could be
required to stop operation of the equipment.
This equipment has been tested and found to comply with
the limits for a class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
CAN ICES-3 (B) / NMB-3 (B)
ENG-4
Nomenclature
Zoom ring (→ 7)
Hood mount (→ 13)
Filter mounting thread
(→ 16)
Focus mode switch (→ 7)
Image stabilizer switch (→ 10)
Image stabilizer mode selector switch (→ 10)
Focusing ring (→ 7)
Lock knob (→ 15)
Focusing distance range
selector switch (→ 9)
Vertical position
indicator (→ 15)
Horizontal position
indicator (→ 15)
Rubber ring (→ 6)
Contacts (→ 6)
Lens mount (→ 6)
Lens mount index (→ 6)
Control ring (→ 9)
Tripod mount (→ 15)
z For detailed information, reference page numbers are provided in parentheses (→ **).
Zoom ring lock lever
(→ 8)
ENG-5
Loading...