Canon POWERSHOT S10 User Manual

Camera User Guide

This guide is for both PowerShot S10 and PowerShot S20 digital cameras.

Please read the notice on the next page before using your camera for the first time.

Refer to this guide for camera operating instructions and the Software Starter Guide for computer and software related instructions.

This user guide is for both the PowerShot S10 and PowerShot S20 models. The model shown in this guide is the PowerShot S20. Unless otherwise noted, the menus and illustrations apply to both the PowerShot S10 and PowerShot S20 models.

Precautions

Camera Body Temperature

If your camera is used for prolonged periods, the camera body may become warm. This is not a malfunction and will not affect the camera’s performance or the stored images. Please be aware of this and take care when operating the camera for an extended period.

About the LCD monitor

The LCD monitor is produced with extremely high-precision manufacturing techniques, with more than 99.99% of the pixels operating to specifications. Less than 0.01% of the pixels may occasionally misfire or appear as black, red or green dots. This has no effect on the recorded image and does not constitute a malfunction.

About 2CR5 Lithium Batteries

• Please note that using 2CR5 lithium batteries at low temperatures will severely limit their performance. Even new batteries may only provide power for a few shots. You can obtain more shots if you warm the battery in your pocket immediately prior to use. When operating the camera at close to 32˚F (0˚C), keep the LCD monitor off and compose images with the optical viewfinder.

• Even if the battery charge appears to be depleted while shooting at low temperature ("Lb" shows in the display panel), the battery may still retain a charge when used at room temperature.

• You are advised to use a power kit (sold separately in some regions), a charged battery pack or an AC adapter if you will be using the camera frequently at low temperatures, loading images onto a computer or performing other tasks that require extended operation.

Notice: Please ensure that you read and follow the handling and safety precautions on

pages 5 to 10 of this guide before attempting to use the camera.

Disclaimer

• While every effort has been made to ensure that the information contained in this guide is accurate and complete, no liability can be accepted for any errors or omissions. Canon Inc. reserves the right to change the specifications of the hardware and software described herein at any time without prior notice.

• No part of this guide may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form, by any means, without the prior written permission of Canon Inc.

• Canon Inc. makes no warranties for damages resulting from corrupted or lost data due to a mistaken operation or malfunction of the camera, the software, the CompactFlash™ cards (CF cards), personal computers, peripheral devices, or use of non-Canon CF cards.

Trademark Acknowledgments

• Canon and PowerShot are trademarks of Canon Inc.

• CompactFlash is a trademark of SanDisk Corporation.

• IBM is a registered trademark of International Business Machines Corporation.

• iBook, iMac and QuickTime are trademarks of Apple Computer, Inc.

• Macintosh, PowerBook and Power Macintosh are trademarks of Apple Computer Inc., registered in the United States and other countries.

• Microsoft, Windows and Windows NT are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.

• Other names and products not mentioned above may be registered trademarks or trademarks of their respective companies.

FCC Notice

(Digital Camera, Model PS 1025 and PC 1002)

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Use of shielded cable is required to comply with Class B limits in Subpart B of Part 15 of the FCC Rules.

Do not make any changes or modifications to the equipment unless otherwise specified in the manual. If such changes or modifications should be made, you could be required to stop operation of the equipment.

Canon U.S.A. Inc. One Canon Plaza, Lake Success, NY 11042, U.S.A. Tel No. (516) 328-5600

Canadian Radio Interference Regulations

THIS CLASS B DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN INTERFERENCECAUSING EQUIPMENT REGULATIONS.

Règlementation canadienne sur les interférences radio

CET APPAREIL NUMERIQUE DE LA CLASSE B RESPECTE TOUTES LES EXIGENCES DU REGLEMENT SUR LE MATERIEL BROUILLEUR DU CANADA.

Table of Contents

Read This First ............................................ 5

Preparing the Camera

Guide to Components ............................... 11

Front View ........................................... 11

Back View ........................................... 12

Operation Panel ................................... 13

Mode Dial ........................................... 14

Display Panel ....................................... 15

Indicators ............................................. 15

Preparing the Battery Pack ..................... 16

Charging the Battery Pack .................. 16

Installing the Battery ........................... 17

Using the AC Adapter ............................... 19

Installing a CF Card ................................... 20

Setting the Date and Time ........................ 23

Setting the Menu Language ..................... 23

Attaching the Wrist Strap ......................... 24

Connecting to a TV ................................... 25

Basic Functions

Before Shooting ........................................ 26

Turning the Power On/Off .................... 26

Using the Viewfinder ........................... 27

Using the LCD Monitor ........................ 27

Using the Shutter Button ...................... 28

Setting the Zoom ................................. 29

Shooting in Auto Mode ............................ 30

Using the Flash .................................... 30

Using the Self-Timer ............................. 31

Using the Focus Lock ........................... 32

Replaying Images ...................................... 33

Erasing Single Images ............................... 34

Shooting

Shooting in Manual Mode ........................ 35

Shooting in Image Mode .......................... 36

Shooting in Stitch Assist Mode ................. 37

How to Frame a Subject ....................... 38

Camera Positioning .............................. 38

Shooting ............................................. 39

Changing the Resolution/Compression .... 41

Shooting Close-Ups (Macro Mode) ............... 42

Shooting Continuously (Continuous Mode) .. 42

Adjusting the Exposure Compensation ........ 43

Setting the White Balance ........................ 44

Shooting with the AE Lock ....................... 45

Setting the Exposure Metering Method .. 45

Adjusting Image Quality Settings ............. 46

Recording Settings .................................... 47

Switching the Digital Zoom On/Off ....... 47

Switching the Review Feature On/Off ... 48

Resetting the File Number .................... 48

Replaying

Magnifying an Image (Single Image Replay) .. 50

Rotating an Image .................................... 50

Jumping Images ........................................ 51

Viewing Image Information ..................... 52

Automated Playback (Slide Show) ............ 52

Starting a Slide Show .......................... 52

Selecting Slide Show Images ............... 53

Setting the Play Time .......................... 54

Setting the Auto Replay On/Off .......... 55

Print Settings (DPOF Settings) ..................... 55

Selecting Images for Printing .............. 55

Selecting the Print Type ....................... 57

Setting the Date/Time Print Function ..... 57

Setting the File Number Print Function .. 58

Resetting Print Settings ....................... 59

Erasing

Quick Erase ............................................... 60

Erasing All Images .................................... 60

Protecting Images .................................... 61

Camera Settings

Displaying the Setup Menu ..................... 63

Setting the Beep On/Off .......................... 64

Adjusting the LCD Monitor Brightness .. 64

Setting the Date/Time.............................. 65

Formatting a CF Card ............................... 65

Setting the Language .............................. 66

Appendices

Replacing the Button Battery ................. 67

Camera Maintenance ............................... 68

Camera Body ...................................... 68

Lens .................................................... 68

Optical Viewfinder .............................. 68

LCD Monitor ....................................... 68

Troubleshooting ....................................... 69

List of Message Codes .............................. 73

List of Messages ....................................... 74

List of Functions ....................................... 76

Specifications ............................................ 77

Index .......................................................... 80

Canon Customer Support ........................ 82

Read This First

Thank you for purchasing a Canon product. Please ensure that you read and understand these handling and safety precautions before you operate your camera and equipment.

Please Read

Test Shots

Before you shoot images of subjects of importance to you, we highly recommend that you shoot several trial images to confirm that you are operating the camera correctly. Please note that Canon Inc., its subsidiaries and affiliates, and distributors of its digital cameras are not liable for any consequential damages arising from any malfunction of a PowerShot camera or CompactFlash™ card (CF card) resulting in the failure of an image to be recorded or to be recorded in a format that is machine sensible.

Warning Against Copyright Infringement

Please note that PowerShot digital cameras are intended for personal use and must be used in a manner that respects international and domestic copyright laws and regulations. Please be advised that in certain cases the copying of images from performances, exhibitions, or commercial properties by means of a camera or other device may contravene copyright or other legal rights even if the image was recorded for personal use.

Use of the Equipment in a Foreign Country

This camera is manufactured according to the specifications of the country in which it is sold and the warranty is only effective in the country of sale. If a problem arises while the camera is in use abroad, please convey it back to the country of sale before proceeding with a warranty claim to a Canon Customer Support Help Desk.

Safety Precautions

• Before using the camera, please ensure that you have read and understood the safety precautions described below. Always ensure that the camera is operated correctly.

• The safety precautions noted on the following pages are intended to instruct you in the safe and correct operation of the camera and its accessories to prevent injuries or damage to yourself, other persons and equipment.

• In the next few pages, the term “equipment” refers primarily to the camera and its power supply accessories.

WARNINGS

• Do not aim the camera directly into the sun or at other intense light sources that could injure your eyesight.

• Do not trigger the flash in close proximity to human or animal eyes. Exposure to the intense light produced by the flash may injure eyesight. In particular, remain at least 39 inches (one meter) away from infants when using the flash.

• Store this equipment out of the reach of children and infants. Accidental damage to the camera or batteries by a child could result in serious injury. In addition, placement of the wrist strap around the child’s neck could result in asphyxiation.

• Be particularly careful to keep the button batteries (CR2016 lithium) used in the camera out of the reach of children. Seek medical assistance immediately if a child swallows a battery.

• Do not attempt to disassemble or alter any part of the equipment that is not expressly described in this guide. Disassembly or alteration may result in high-voltage electrical shock. Internal inspections, alterations and repairs should be conducted by qualified service personnel authorized by your camera distributor or a Canon Customer Support Help Desk.

• To avoid the risk of high-voltage electrical shock, do not touch the flash portion of the camera if it has been damaged. Similarly, never touch internal portions of the equipment that become exposed as a result of damage. There is a risk of high-voltage electrical shock. Please take the first opportunity to consult your camera distributor or a Canon Customer Support Help Desk.

• Stop operating the equipment immediately if it should emit smoke or noxious fumes. Failure to do so may result in fire or electrical shock. Immediately turn the camera’s mode dial to the Off position and remove the camera battery or unplug the power cord from the electrical outlet. Confirm that smoke or fume emissions cease. Please consult your camera distributor or the closest Canon Customer Support Help Desk.

• Stop operating the equipment if it is dropped or the casing is damaged. Failure to do so may result in fire or electrical shock. Immediately turn the camera’s mode dial to the Off position and remove the camera battery or unplug the power cord from the electrical outlet. Please consult your camera distributor or the closest Canon Customer Support Help Desk.

• Prevent the equipment from contact with, or immersion in, water and other liquids. Do not allow liquids to enter the interior. The camera has not been waterproofed. If the exterior comes into contact with liquids or salt air, wipe it dry with a soft, absorbent cloth. In the event that water or other foreign substances enter the interior, immediately turn the camera’s mode dial to Off and remove the camera battery or unplug the power cord from the electrical outlet. Continued use of the equipment may result in fire or electrical shock. Please consult your camera distributor or the closest Canon Customer Support Help Desk.

Read This First

• Do not use substances containing alcohol, benzene, thinners or other flammable substances to clean or maintain the equipment. The use of these substances may lead to fire.

• Do not cut, damage, alter or place heavy items on the power adapter cord. Any of these actions may cause an electrical short circuit, which may lead to fire or electrical shock. Replace a broken or damaged power adapter cord.

• Do not handle the power cord if your hands are wet. Handling it with wet hands may lead to electrical shock. When unplugging the cord, ensure that you hold the rigid portion of the plug. Pulling on the flexible portion of the cord may damage or expose the wire and insulation, creating the potential for fires or electrical shocks.

• Use of power sources not expressly recommended for this equipment may lead to overheating, distortion of the equipment, fire, electrical shock or other hazards. Use only the recommended power accessories.

• To connect an interface cable to a port other than a USB port, power down the computer and unplug the power cord before attempting to connect it to avoid the risk of electrical shock.

• Do not place the batteries near a heat source or expose them to direct flame or heat. Neither should you immerse them in water. Such exposure may damage the batteries and lead to the leakage of corrosive liquids, fire, electrical shock, explosion or serious injury.

• Do not attempt to disassemble, alter or apply heat to the batteries. There is serious risk of injury due to an explosion. Immediately flush with water any area of the body, including the eyes and mouth, or clothing, that comes into contact with the inner contents of a battery. If the eyes or mouth contact these substances, immediately flush with water and seek medical assistance.

• Avoid dropping or subjecting the batteries to severe impacts that could damage the casings. It could lead to leakage and injury.

• Do not short-circuit the battery terminals with metallic objects, such as key holders. It could lead to overheating, burns and other injuries. Use the supplied battery case to transport or store the battery pack.

• Before you discard a battery, cover the terminals with tape or other insulators to prevent direct contact with other objects. Contact with the metallic components of other materials in waste containers may lead to fire or explosions. Discard the batteries in specialized waste facilities if available in your area.

• Use of batteries not expressly recommended for this equipment may cause explosions or leaks, resulting in fire, injury and damage to the surroundings. Use only recommended batteries and accessories.

• Use only the recommended compact power adapter to charge the Battery Pack NB-5H rechargeable batteries. Use of chargers not expressly recommended may result in overheating, distortion, fire or electrical shock.

• Disconnect the compact power adapter from both the camera and electrical outlet after recharging and when the camera is not in use to avoid fires and other hazards.

• The camera terminal of the compact power cord is designed for exclusive use with the PowerShot S10 and PowerShot S20. Do not use it with other products or batteries. There is a risk of fire and other hazards.

CAUTION

• Avoid using, placing or storing the equipment in places subject to strong sunlight or high temperatures, such as the dashboard or trunk (boot) of a car. Exposure to intense sunlight and heat may cause the batteries to leak, overheat or explode, resulting in fire, burns or other injuries. High temperatures may also cause deformation of the casing. Ensure that there is good ventilation when using the compact power adapter to charge the battery pack or power the camera.

• Do not store the equipment in humid or dusty areas. Storage in these areas could lead to fire, electrical shock or other damage.

Read This First

• Be careful not to bang the camera or subject it to strong impacts or shocks that could lead to injury or damage the equipment when wearing or holding it by the wrist strap.

• Be careful not to cover the flash with your fingers when shooting. In addition, do not touch the surface of the flash after taking several pictures in rapid succession. Either action could result in burns.

• If your camera is used for prolonged periods, the camera body may become warm. Please take care when operating the camera for an extended period as your hands may experience a burning sensation.

Preventing Malfunctions

Avoid Strong Magnetic Fields

Never place the camera in close proximity to electric motors or other equipment generating strong electromagnetic fields. Exposure to strong magnetic fields may cause malfunctions or corrupt image data.

Avoid Condensation Related Problems

Moving the equipment rapidly between hot and cold temperatures may cause condensation (water droplets) to form on its external and internal surfaces. You can avoid this by placing the equipment in an airtight, resealable plastic bag and letting it adjust to temperature changes slowly before removing it from the bag.

If Condensation Forms Inside the Camera

Stop using the camera immediately if you detect condensation. Continued use may damage the equipment. Remove the CF card and battery or power cord (if connected) from the camera and wait until the moisture evaporates completely before resuming use.

Extended Storage

When not using the camera for extended periods of time, remove the battery (except the CR2016 lithium button battery) and store the equipment in a safe place. Storing the camera for extended periods with a battery installed will run down the battery and may damage the camera.

Preparing the Camera

Guide to Components

This section explains how to install the batteries, CF card and wrist strap.

Front View

• Lens

• AF Auxiliary Light Emitter

• Optical Viewfinder Window (p. 27)

• Display Panel (p. 15)

• Red-Eye Reduction Lamp (p. 31)

• Flash (p. 30)

• VIDEO OUT Terminal (p. 25)

• Button Battery Holder (p. 67)

• DIGITAL Terminal*

• DIGITAL Terminal Cover

* Used when the camera is connected to a computer.

Open the cover and connect the interface cable to the camera’s digital terminal and the computer. See the Software Starter Guide for additional information.

Back View

• Optical Viewfinder (p. 27)

• Tripod Socket

• LCD Monitor* (p. 27)

• CF Card Slot Cover (p. 20)

• Lock for CF Card Slot Cover (p. 20)

• Strap Holder (p. 24)

• DC Coupler Cable Cover

• Battery Cover (p. 17)

• Battery Cover Lock (p. 17)

* The LCD monitor is produced with extremely high-

precision manufacturing techniques. More than

99.99% of the pixels operate to specification. Less than 0.01% of the pixels may occasionally misfire or appear as black or red dots. This has no effect on the recorded image and does not constitute a malfunction.

Operation Panel

• Mode Dial (p. 14)

• Indicators (p. 15)

• (Macro) /Jump Button (pp. 42, 51)

•

(Continuous) / (Self-Timer) / (Magnification) Button (pp. 42, 31, 50)

(Flash) Button / (Multi) Button (pp. 30, 33)

•

• Shutter Button (p. 28)

• Omni Selector Button,

(Telephoto) / (Wide Angle) Button

(p. 29)

(Exposure/White Balance) Button

•

(pp. 43, 44)

• MENU / SET Button

• DISPLAY Button (pp. 27, 52)

Preparing the Camera

Mode Dial

The Mode Dial is used to select the recording and play modes.

• (Off)

Turn the dial to this position when the camera is not being used. The lens cover will close and the camera will power down. (p. 26)

• (Auto Mode)

A recording mode in which the camera automatically selects most of the settings. (p. 30)

• (Manual Mode)

A recording mode in which the image compression and resolution, exposure compensation and white balance can be manually selected. (p. 35)

• (Image Mode)

A recording mode with settings adjusted to specific circumstances, such as landscapes, night scenes and black and white images. (p. 36)

• (Stitch Assist Mode)

A recording mode that facilitates the creation of a multi-frame panorama that you merge with the supplied software. (p. 37)

• (Play Mode)

The mode that allows images recorded on a CF card to be replayed and erased. (pp. 33, 50)

• (PC Mode)

The mode for exchanging image files with a connected computer. (See the Software Starter Guide)

• “PC” will appear in the display panel when a connection to a computer is established.

Display Panel

The camera status is shown in the display panel. Settings, the remaining image capacity and the battery charge are among the data it displays.

Remaining Image Capacity

: Flash On : Flash Off : Red-Eye Reduction : Macro Mode : Single Mode : Continuous Mode : Self-Timer Mode : White Balance On : Low Battery

• The above example shows all the symbols appearing at once for illustration purposes. In fact, only the applicable symbols are displayed at any one time.

• Operating codes and error codes may also appear in the display panel. (p. 73)

: Exposure

Compensation On

: Beep On : Super Fine : Fine : Normal : Large : Middle : Small

Indicators

The indicators shine or flash when the shutter button is pressed to signal various states.

• Upper Indicator

Green: Ready to record Flashing Green: Recording to CF card/

Reading CF card Red: Ready to record with flash Flashing Red: Camera blur warning (low

light warning)

• Lower Indicator

Orange: Macro mode

Preparing the Camera

Preparing the Battery Pack

Battery Pack NB-5H, Compact Power Adapter CA-PS100/100E, power cords, DC Coupler DR-100A and 2CR5 lithium batteries are sold separately in some regions.

To confirm the package contents, see the back of the System Map packaged with your camera.

Charging the Battery Pack

Use the procedures below to fully charge Battery Pack NB-5H.

Compact Power Adapter CA-PS100/100E

To AC Electrical Outlet

AC Power Cord

Battery Pack NB-5H

• The CHARGING indicator will flash green while the battery pack is charging. It will change to a steady green when the battery pack is charged.

• Remove the plug from the electrical outlet after the battery pack is charged.

• It takes approximately 90 minutes to

charge the battery pack, taking it from a completely discharged state to a fully charged one. (Based on Canon standard testing conditions using Compact Power Adapter CA-PS100/100E.)

• Charge times will vary according to the

ambient temperature and the charge state of the battery pack.

• To protect and prolong the battery pack

life, do not charge it longer than 24 hours at a time.

• Do not charge the battery pack in poorly

ventilated areas.

• Do not charge batteries other than

Battery Pack NB-5H with the compact power adapter.

CHARGING Indicator

• The battery pack continues to discharge a minimal portion of its power while installed in the camera, even with the camera power off. This will shorten the battery life. Remove it from the camera during extended periods of disuse. Place it into the case provided and store it in a cool, dry place. Be sure to charge it fully before using it after a period of extended storage.

• Repeated recharging before the charge is completely discharged may diminish the charge capacity. Completely discharge and fully charge the battery pack several times to restore its capacity.

• If the time over which the battery pack can be used diminishes substantially even when it is fully charged, the battery pack should be replaced.

Installing the Battery

Install the 2CR5 lithium battery or the rechargeable Battery Pack NB-5H.

1 Turn the Mode Dial to the position.

2 Slide the battery cover lock in the

direction of the arrow and open the battery cover.

3 Install the battery as shown in the

diagram.

Battery

2CR5 Lithium Battery

Battery Terminals

Pack NB-5H

Preparing the Camera

4 Close the battery cover.

• A flashing green indicator signals that an image is being written to, or read from, the CF card. Do not open the battery cover while this is in process.

• Remove the battery from the camera when the camera is not in active use.

• Use the rechargeable Battery Pack NB5H or the AC adapter (sold separately in some regions) when you use the camera for an extended period of time.

• Replace the supplied 2CR5 lithium battery with a new one of the same type.

Lithium Batteries

• The performance of lithium batteries is severely reduced at low temperatures. Consequently, you may only be able to take a few pictures, even with a brand new 2CR5 lithium battery. To improve the performance at low temperatures, warm the battery in your pocket before using it in the camera. It is also advisable to shut off the LCD monitor and use the optical viewfinder to compose images at temperatures close to 32˚F (0˚C).

• A lithium battery that appears to have lost its charge at cold temperatures may still be usable at room temperature.

• Do not use a lithium battery that has been used in another camera. A malfunction may result.

Battery Performance

PowerShot S10/PowerShot S20

No. of Images

LCD MonitorOnLCD Monitor

Battery Pack NB-5H (fully charged)

2CR5 Lithium Battery (Sanyo Brand, new)

* The actual performance may vary from the above

data according to the shooting conditions and the selected recording mode.

Approx. 55 shots

Approx. 65 shots

Approx.

230 shots

Approx.

400 shots

Test Conditions

Recording: 73°F (23°C), (Large)/ (Fine), Zoom used, Replay: 73°F (23°C), continuous replay, 5 seconds

flash used once every 4 shots, CF card used

per image, CF card used

Off

Replay

(Minutes)

Approx.

50 min.

Approx.

80 min.

Using the AC Adapter

You are recommended to use the AC adapter when you will be using the camera for a relatively long period of time. Attach the AC adapter as shown below.

Cable Cover

Camera Indicator (DC Output)

DC Coupler DR-100A

Compact Power Adapter

• The CAMERA indicator on the compact power adapter will shine red when it is powering the camera.

• Always remove the plug from the electrical outlet when you have finished using the camera.

DC Terminal

Preparing the Camera

• Battery Pack NB-5H cannot be charged while the compact power adapter is used to power the camera.

• Do not use the compact power adapter to power any device other than one for which Battery Pack NB-5H is specified.

Installing a CF Card

• Please note that CF cards formatted or edited in another manufacturer’s camera or application program may not operate correctly in the camera.

3 Insert the CF card with the label facing up

and the arrow pointing in as viewed from the camera back, pushing it gently in until the slot’s eject button is fully extended.

Arrow

Label

1 Turn the Mode Dial to the

2 Slide the lock for the CF card slot cover to

the open position and open the cover.

position.

CF Card Eject Button (Push to eject)

* The CF card supplied with the camera may vary

from the one shown in this guide.

4 Close the CF card slot cover gently but

firmly until it locks.

• Never turn off the power or remove the CF card while the camera is writing to, reading from, or erasing from, the CF card.

About CF Cards

• CF cards are high-precision electronic devices. Do not bend, apply force to, or subject them to shocks or vibration.

• Do not attempt to disassemble or alter a CF card.

• Moving a CF card rapidly between temperature extremes will cause condensation to form in the card and may lead to a malfunction. To avoid condensation, place the CF card into a sealed plastic bag before moving it into a different temperature zone and allow it to adjust slowly to the new temperature. If condensation forms on the CF card, put it aside until the water droplets have evaporated completely.

• Place the CF card in the supplied case for storage.

• Do not use or store CF cards in the following types of location.

- Locations subject to strong magnetic

fields

- Locations subject to dust or sand

- Locations subject to high humidity and

high temperatures

CF Cards and Estimated Capacities

PowerShot S10

FC-8M FC-16M FC-30M FC-48M FC-8M FC-16M FC-30M FC-48M

124

101

140

139 256

152 30 75

114

211 63

209

384

15 37 68 31 68

12 24

7 18 33 15 33 61

* These figures reflect standard shooting conditions

established by Canon. Actual totals may vary according to the subject and shooting conditions.

* Some CF cards are not sold in some regions.

• L (Large), M (Middle) and S (Small) indicate the recording resolution as follows.

(Large) (Middle) (Small)

PowerShot S10 PowerShot S20

1600 x 1200 pixels 1280 x 960 pixels

800 x 600 pixels

• (Super Fine), (Fine) and (Normal) indicate the compression, or the relative extent to which the image data is compressed.

31 79

PowerShot S20

82 17 46 87

167 36 94

192

176

355

2048 x 1536 pixels 1024 x 768 pixels

640 x 480 pixels

14 33 64 36 91

136 252 111 289 533

Preparing the Camera

21 50 97 55

Precautions with CF Cards

Please note that the PC card icon may take a moment (about 1 minute) to appear on the Taskbar of certain computers after insertion in a PC card slot. If this occurs, you should delete the Windows standard driver and install the SanDisk ATA FlashDisk device driver. The procedures are described below. Please consult your computer manufacturer if you are uncertain about these procedures.

How to Remove the Windows Standard Driver

1. Insert the CF card (with adapter) into the PC card slot. Right-click the [My computer] icon and select [Properties].

2. The System Properties dialog will appear. Click the [Device Manager] tab and select [View devices by connection] check box at the top.

3. Click the [Computer] option, select the device with the PC card icon and click the [Remove] button.

4. When the Confirm Device Removal dialog appears, click the [OK] button.

5. Close the System Properties dialog.

6. Remove the CF card from the slot.

How to Install the SanDisk ATA FlashDisk Device Driver

1. Insert the CF card into the PC card slot.

2. The New Hardware Found dialog will appear. Choose the [Select from a list of alternative drivers] option and click the [OK] button.

3. Select the [Show all devices] option in the Select Device dialog.

4. Select [SanDisk] in the Manufacturers category. SanDisk ATA FlashDisk will automatically be selected in the Models category. Finish by clicking the [OK] button.

Setting the Date and Time

The Set Date/Time menu will appear the first time the camera is turned on after it is purchased. Use the following procedures to set the correct date and time.

1 Turn the Mode Dial to the , ,

2 Set the date, time and date format.

3 Press the SET button

, or position. The Set Date/ Time menu will display the first time the camera is turned on.

The factory default for the date format may differ from that shown in some regions.

• Use the or button to select a field, such as month, day, year, hour, minute or date format.

• Use the or buttons to adjust the value in a field.

• To cancel the setting without changing the date or time, press the Menu button.

Setting the Menu Language

You can change the language in which messages are displayed. The language menu may appear differently on cameras in some regions.

1 Turn the Mode Dial to the position.

2 Press and hold the SET button, then press

3 Use the

/JUMP button to display the

the Language menu.

language and the SET button to execute the selection.

and buttons to select a

• The menu language can also be set with standard Setup menu procedures (p. 66).

Preparing the Camera

Attaching the Wrist Strap

1 Slip the small loop at the end of the wrist

strap through the strap holder.

Strap holder

3 Pull the strap through the loop until the

loop slips over the plastic part of the strap.

2 Pass the other end of the wrist strap

through the small loop.

• Be careful not to wave the camera about or to catch it on other items when holding it by the wrist strap.

+ 61 hidden pages