Canon Optura 20 Service Manual

Mini

Digital Video Cassette

PUB.DIM-483

DIGITAL VIDEO CAMCORDER

Instruction Manual

CAMESCOPE ET LECTEUR VIDEO NUMERIQUES

Mode d’emploi

VIDEOCAMARA Y GRABADORA DIGITAL

Manual de Instrucciones

ENGLISH

FRANÇAIS

ESPAÑOL

NTSC

Important Usage Instructions

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

Introduction

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

WARNING:

TO REDUCE THE RISK OF ELECTRIC SHOCK AND TO REDUCE ANNOYING INTERFERENCE, USE THE RECOMMENDED ACCESSORIES ONLY.

Unauthorized recording of copyrighted materials may infringe on the rights of copyright owners and be contrary to copyright laws.

Digital Video Camcorder, OPTURA200 MC systems This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and use in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help. Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules.

Do not make any changes or modifications to the equipment unless otherwise specified in the manual. If such changes or modifications should be made, you could be required to stop operation of the equipment.

Canon U.S.A. Inc. One Canon Plaza, Lake Success, NY 11042, U.S.A. Tel No. (516)328-5600

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

Important Warning

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure, that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point, within an equilateral triangle, is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

IMPORTANT SAFETY INSTRUCTIONS

In these safety instructions the word “product” refers to the Canon Digital Video Camcorder OPTURA200 MC A and all its accessories.

1. Read Instructions — All the safety and operating instructions should be read before the product is operated.

2. Retain Instructions — The safety and operating instructions should be retained for future reference.

3. Heed Warnings — All warnings on the product and in the operating instructions should be adhered to.

4. Follow Instructions — All operating and maintenance instructions should be followed.

5. Cleaning — Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. The product should be cleaned only as recommended in this manual.

6. Accessories — Do not use accessories not recommended in this manual as they may be hazardous.

7. Avoid magnetic or electric fields — Do not use the camera close to TV transmitters, portable communication devices or other sources of electric or magnetic radiation. They may cause picture interference, or permanently damage the camera.

8. Water and Moisture — Hazard of electric shock — Do not use this product near water or in rainy/moist situations.

9. Placing or Moving — Do not place on an unstable cart, stand, tripod, bracket or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.

10. Power Sources — The CA-560 Compact Power Adapter should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. Regarding other power sources such as battery power, refer to instructions in this manual.

11. Polarization — The CA-560 Compact Power Adapter is equipped with a polarized 2-prong plug (a plug having one blade wider than the other). The 2-prong polarized plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug still fails to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.

12. Power Cord Protection — Power cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them. Pay particular attention to plugs and the point from which the cords exit the product.

13. Outdoor Antenna Grounding — If an outside antenna is connected to the product, be sure the antenna is grounded so as to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical Code, ANSI / NFPA No. 70—1984, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. See figure 1.

Introduction

EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE

ANTENNA LEAD IN WIRE

ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)

GROUNDING CONDUCTORS (NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250. PART H)

NEC - NATIONAL ELECTRICAL CODE

ELECTRIC SERVICE EQUIPMENT

GROUND CLAMP

Fig. 1

14. Lightning — For added protection of this product during a lightning storm, or when it is left unattended and unused for long periods of time, disconnect it from the wall outlet and disconnect the antenna. This will prevent damage to the product due to lightning and power-line surges.

15. Overloading — Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.

16. Objects and Liquid Entry — Never push

Introduction

objects of any kind into this product through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Be careful not to spill liquid of any kind onto the product.

17. Servicing — Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

18. Damage Requiring Service — Disconnect this product from the wall outlet and all power sources including battery, and refer servicing to qualified service personnel under the following conditions: a. When the power-supply cord or plug is

damaged.

b. If any liquid has been spilled onto, or

objects have fallen into, the product.

c. If the product has been exposed to rain

or water.

d. If the product does not operate

normally even if you follow the operating instructions. Adjust only those controls that are covered by the operation instructions. Improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation.

e. If the product has been dropped or the

cabinet has been damaged.

f. When the product exhibits a distinct

change in performance. This indicates a need for service.

19. Replacement Parts — When replacement parts are required, be sure the service technician has used replacement parts that are specified by Canon or that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards.

20. Safety Check — Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in safe operating order.

When replacement of power supply is required, please return it to the responsible nearest Canon Service Center and please replace it with the same type number CA-560 or equivalent.

The Adapter can be used with a power supply between 100 and 240 V AC. For areas where 120 V AC power is not used, you will need a special plug adapter. Contact your nearest Canon Service Center for further information.

Reference Guide

Three manuals are supplied with your camcorder: the “Digital Video Camcorder OPTURA200 MC Instruction Manual”, “DIGITAL VIDEO SOLUTION DISK Software Instruction Manual”, and the “DV NETWORK SOLUTION DISK Software Instruction Manual”.

■ Digital Video Camcorder OPTURA200 MC Instruction Manual

This manual explains the camcorder operations such as recording and playing back still images and movies on a tape or a memory card.

■ DIGITAL VIDEO SOLUTION DISK Software Instruction Manual

This manual explains how to download still images and movies from the memory card to a computer by using the supplied USB cable. You can also add sample images for the card mix function, or the “my camera” settings to the camcorder.

Windows XP Only

■ DV NETWORK SOLUTION DISK Software Instruction Manual

This manual explains how to download still images and movies from the memory card to a computer by using the DV (IEEE1394) cable. You can also perform videoconference and file transfer over the Internet using Windows XP’s Windows Messenger. There are several requirements for using this software. For details, please refer to this instruction manual.

Introduction

Trademark Acknowledgements

• Canon is a registered trademark of Canon Inc.

• ArcSoft is a trademark or registered trademarks of ArcSoft, Inc.

• Macintosh is a trademark of Apple Computer Inc., registered in the United States and other countries.

• Windows®is either a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries.

• Other names and products not mentioned above may be registered trademarks or trademarks of their respective companies.

Contents

Important Usage Instructions ................2

IMPORTANT SAFETY

INSTRUCTIONS ................................3

Reference Guide....................................5

Thank you for Choosing a Canon ........8

Introducing the OPTURA200 MC ..........9

Mastering the Basics

Introduction

Finding Your Way Around

the OPTURA200 MC ......................10

Preparations

Powering Your Camcorder ..................13

Loading a Cassette..............................18

Basic Recording

Basic Recording ..................................20

Zooming ............................................25

Introduction

Using the LCD Screen..........................27

Tips for Making Better Videos ............30

Basic Playback

Playing Back a Tape ............................32

Connections for Playback on a

TV Screen ......................................36

Using the Full Range of Features

General

Searching and Reviewing While

Recording ......................................39

Using the Menus ................................40

Using the Wireless Controller ..............50

Recording

Setting the Date and Time ..................53

Recording Still Images onto a Tape ......56

Using the Built-in flash ........................58

Turning the Image Stabilizer Off..........60

Using the Various Recording

Programs ........................................61

Using Digital Effects ............................65

Using the Multi-Image Screen ............71

Audio Recording ................................73

Setting the Self-Timer..........................75

Manual Adjustments

Adjusting Exposure Manually ..............77

Setting the Shutter Speed ..................79

Adjusting Focus Manually....................81

Setting the White Balance ..................83

Playback

Enlarging the Image during Playback ..85 Displaying Date, Time and Camcorder

Data (Data Code)............................86

Searching the Tape (Photo Search/

Date Search) ..................................89

Returning to a Pre-Marked Position ....90

Editing

Editing to a VCR ................................91

Dubbing to/from a Tape with Digital

Video Equipment............................92

Recording from a VCR, TV or Analog

Camcorder (Analog Line-in) ............94

Digitally outputting analog video

and audio signals

(Analog-Digital Converter) ..............96

Recording Over Existing Scenes

(AV Insert Editing) ..........................98

Audio Dubbing ................................101

Setting the Audio Mix ......................104

Connecting to a PC Using a

DV Cable......................................106

Using a Memory Card

Memory Card Introduction................107

Recording Still Images onto a

Memory Card ..............................112

Recording Still Images from a tape....115

Recording Still Images from Other

Devices (VCR, TV or Other Digital

Camcorders) ................................116

Recording Movies onto a

Memory Card ..............................117

Recording Movies from a Tape ..........118

Recording Movies from Other Devices

(VCR, TV or Other Digital

Camcorders) ................................119

Recording Panoramic Images

(Stitch Assist) ................................120

Playing Back a Memory Card ............122

Settings of the Still Images/Movies ....125

Preventing Accidental Erasure

(Protect) ..................................128

Marking a Still Image for Printing

(Print Mark)..............................129

Erasing Still Images ......................131

Using Printers Supporting the Direct

Print Function (Optional) ..............133

Combining Images (Card Mix) ..........142

Copying Still Images from Tape to

Memory Card ..............................147

Copying Still Images from Memory

Card to Tape ................................148

Formatting a Memory Card ..............149

Connecting to a PC Using a

USB Cable ....................................150

Other Information and Precautions....153

Additional Information

Preparing the Camcorder ..................156

Notes on Using the Batteries ............158

Maintenance ....................................161

Troubleshooting ................................165

The OPTURA200 MC System

Diagram ......................................169

Optional Accessories ........................170

Screen Displays..................................173

Specifications ....................................183

Index ................................................185

Menu at a Glance ............................187

Introduction

Symbols Used in this Instruction Manual

: Reference page numbers : Functions that can be operated from the body of the camcorder

: Functions that can be operated from the wireless controller : Supplementary notes for camcorder operation

` : Operation confirmation beeps ( 24)

• Capital letters are used to refer to settings displayed in the menus and buttons labeled on the camcorder itself, e.g. Press the MENU button.

The serial number of this product may be found on the bottom of the camcorder. No others have the same serial number as yours. You should record the number and other vital information here and retain this book as a permanent record of your purchase to aid identification in case of theft.

Date of Purchase Dealer Purchased From Dealer Address Dealer Phone No. Model Name OPTURA200 MC Serial No.

Thank You for Choosing a Canon

First, we’d like to thank you for purchasing this Canon camcorder. Its

advanced technology makes it very easy to use — you will soon be making high-quality videos which will give you pleasure for years to come.

To get the most out of your new camcorder, we recommend that you read this manual thoroughly — there are many sophisticated features which will add to your recording enjoyment.

Getting Started

To get started we suggest that you master the basic operations of the camcorder first, before moving on to use its full range of features.

Introduction

Your camcorder is supplied with the following accessories:

WL-D78 Wireless

WL-D74 Wireless

Controller

Lens hood Lens cap and lens cap

SS-600 Shoulder Strap Lens cap and lens cap

BP-512 Battery Pack

BP-511 Battery Pack

Lithium button battery

CR1616

Two AA batteries

cord

CA-560 Compact Power

Adapter

Adapter (including AC

(including power cord)

power cable)

S-150 S-video Cable

STV-250N Stereo

STV-250 Stereo Video

Video Cable

Cable

Soft case for SD Memory Card

Digital Video Solution Disk DV Network Solution Disk ArcSoft Camera Suite CD

SDC-8M SD Memory Card (with pre-recorded sample images)

IFC-300PCU USB cable

Introducing the OPTURA200 MC

Mega-pixel CCD

Your camcorder incorporates a megapixel CCD. High-resolution still images can be recorded onto a memory card.

Built-in Flash

The built-in flash automatically rises up and fires according to the brightness of the surrounding area.

10× Optical Zoom and 200×

(card 40×) Digital Zoom

Optical Image Stabilizer

Canon’s optical technology stabilizes your recordings even in long telephoto shots.

Super Night Mode & Night Mode

Allows you to record even in dark places. The Night mode adjusts automatically to the optimum shutter speed, and the Super Night mode utilizes the Super Night LED to record bright colorful pictures.

Direct Printing

You can print still images by connecting the camcorder to a printer supporting the Direct Print function.

My Camera Function

You can customize the start up image and shutter sound of the camcorder.

USB Terminal

Allows high-speed transfer of memory card data to a PC with a built-in USB port. You can organize and edit still images/movies on your PC using the supplied software.

IEEE 1394 DV Terminal

The DV terminal allows high-quality transfer with virtually no deterioration in quality of images. You can edit and process images by connecting the camcorder to a PC with the IEEE 1394 terminal.

nalog Line-in Recording

Audio Dubbing/AV Insert Editing

Introduction

Still Images

You can record still images like photographs. You can also shoot continuously still images and record them onto a memory card.

Memory Card

You can record still images and movies onto a SD Memory Card or MultiMediaCard. Transfer still images/movies to your PC and use the supplied software to edit or attach them to your e-mail, or merge separate still image into one large panoramic scene.

Digital Effects

Show your creativity by using the special effects and digital faders. These digital effects and faders

can add visual appeal and greater imaging variety. The multiimage screen captures moving subjects in 4, 9 or 16 sequences of still images.

Finding Your Way Around the OPTURA200 MC

(

)

INDEX

REC SEARCH

SCREEN

MIX/

CARD

SLIDE SHOW

LCD screen (p. 27)

Flash button (p. 58)/ (play/pause) button (p. 32)

(stop) button (p. 32)/ INDEX SCREEN button (p. 124)

BATT. (battery) RELEASE button (p. 15)

Memory card compartment cover (p. 108)

Battery attachment unit (p. 14)

LCD panel OPEN button (p. 27)

REC (record) SEARCH

button (p. 39)/ (fast forward) button (p. 32)/ CARD

+ button (p. 120, 123)

REC (record) SEARCH –

button(p. 39)/

Record review button (p. 39)/

(rewind) button (p. 32)/

CARD

–

button (p. 120, 123)

DIGITAL EFFECTS button (p. 65)

Digital effects ON/OFF button (p. 65)

FOCUS button(p. 81)/ DATA CODE button (p. 86)

EXP (exposure) button (p. 77)

Enlarge buttons (p. 85)/ Trimming buttons (for direct printing) (p.139)

Card MIX button (p. 144)/ SLIDE SHOW button (p. 124)

Self-timer button (p. 75)/ REC PAUSE (Line-in) button (p. 93, 95)

the Basics

Mastering

Stereo microphone (p. 73, 101)

Built-in speaker (p. 35)

Viewfinder (p. 156)

MENU button (p. 41)

Viewfinder focusing lever (p. 156)

Program selector (p. 61)

Program AE

Easy Recording

Card access indicator (p. 112)

Start/Stop button (p. 21)

)

(

CARD TAPE

Tripod socket (p. 30)

POWER indicator (p. 20)

POWER switch (p. 20)

TAPE/CARD switch (p. 21)

PHOTO button (p. 56, 112)

Zoom lever (p. 25)

Backup battery cover (p. 160)

AV (audio/video) IN/OUT terminal

AV IN/OUT

(p. 36, 94)/

MIC

(phones) terminal (p. 35)

IN/ OUT

MIC terminal (p. 73, 101)

S-video (IN/OUT) terminal (p. 37, 94)

Selector dial (p. 35, 41)

Grip belt (p. 157)

Bottom view

OPEN/EJECT

the Basics

Mastering

OPEN/EJECT switch (p. 18)

DC IN 9.5V

IN/OUT

CHARGE

WIRELESS CONTROLLER WL-D78

REW

PLAY

START

/STOP

PHOTO

SELF TIMER

TV SCREEN

DATA CODE

CARD

AUDIO

MONITOR

REC

PAUSE

SEARCH SELECT

SLIDESHOW

ZERO SET MEMORY

INDEX

SCREEN

AUDIO

DUB.

STOP

MIX

BALANCE

ST-1 ST-2

ON/OFF

D.EFFECTS

SET

ZOOM

AV INSERT

PAUSE

SLOW

REMOTE SET

AV DV

× 2 button (p. 34)

START/STOP button (p. 20)

MENU button (p. 41)

TV SCREEN button (p. 173)

SELF TIMER button (p. 75)

DATA CODE button (p. 86)

D.EFFECTS (Digital effects) button (p. 65)

REC PAUSE button (p. 93, 95)

CARD

–/+ buttons (p. 123)

Transmitter

Zoom buttons (p. 25)

SET button (p. 41)

Digital effects ON/OFF button (p. 65)

MIX BALANCE buttons (p. 104)

Controller buttons (p. 42)

Search buttons (p. 89)

SEARCH SELECT button (p. 89)

AUDIO MONITOR button (p. 104)

AUDIO DUB. button (p. 102)

AV INSERT button (p. 100)

REMOTE SET button (p. 51)

AV DV button (p. 97)

+ button (p. 33)

– button (p. 33)

FF button (p. 32)

PLAY button (p. 32)

STOP button (p. 32)

SLOW button (p. 33)

REW button (p. 32)

PAUSE button (p. 33)

PHOTO button (p. 56, 112)

SLIDE SHOW button (p. 124)

INDEX SCREEN button (p. 124)

Remote sensor (p. 50)

Tally lamp (p. 23)

Terminal cover

Lens hood (p. 156)

Focus ring (p. 81)

u (LANC) terminal (p. 91)

Cassette compartment (p. 18)

Cassette compartment cover (p. 18)

DC IN terminal (p. 13)

DV IN/OUT terminal (p. 92)

CHARGE indicator (p. 14)

Built-in Flash (p. 58)

Super Night LED (white LED) (p. 58, 64, 82)

USB terminal (p. 150)

Enlarge buttons (p. 85)/ Trimming buttons (for direct printing) (p. 139)

ZERO SET MEMORY button (p. 90)

the Basics

Mastering

Powering Your Camcorder

Before operating your camcorder, you will need to use the power adapter to:

Provide power from a household power socket

Charge a battery pack

Notes:

• The power adapter converts current from a household power socket (100–240 V AC, 50/60 Hz) to the DC current used by your camcorder.

• If the adapter is used next to a TV, it may cause bars to appear on the TV — move the adapter away from the TV or the antenna cable.

• Do not connect products not expressly recommended to the camcorder’s DC terminal. Likewise, do not connect products not expressly recommended to the power adapter.

Connecting the Camcorder to a Household Power Socket

)

(

Use the power adapter to provide your camcorder with instant power from a household power socket. Always turn the camcorder off before connecting/removing the power source.

1. Set the POWER switch to OFF.

2. Connect the power cord to the power adapter.

3. Plug the power cord into a household power socket.

4. Connect the power adapter to the camcorder’s DC IN

terminal.

5. Disconnect the power adapter from the camcorder after use.

Unplug the power cord from the household power socket, then disconnect it from the adapter.

the Basics

Mastering

DC IN 9.5V

CHARGE

(

)

Attaching and Charging the Battery Packs

CHARGE indicator

Your battery pack has been partially charged before it left the factory. It should have enough power for you to check that your camcorder is working properly. Charge the battery pack fully if you want it to power the camcorder for more than a few minutes. Always turn the camcorder off before connecting/removing the battery.

the Basics

1. Set the POWER switch to OFF.

Mastering

2. Attach the battery to the camcorder.

• Remove the battery pack’s terminal cover.

• Align the edge of the battery pack with the line on the camcorder, press lightly and slide it in the direction of the arrow until it clicks into place.

3. Connect the power cord to the adapter and plug it into a household power socket.

4. Connect the power adapter to the camcorder.

• The charge indicator flashes red to show that charging is in progress.

Single flashes mean that the battery pack is less than 50% charged. Double flashes mean that it is more than 50% charged. The indicator glows steadily when the battery pack is fully charged. If the indicator blinks rapidly and continuously (twice a second), the battery pack may be defective.

• When the CHARGE indicator flashes, the battery pack is being charged

even if the POWER switch is set to a position other than OFF.

5. When charging is complete, disconnect the power adapter from the camcorder, unplug the power cord, and disconnect the power cord from the adapter.

6. Remove the battery pack after use.

Press the BATT. RELEASE button and remove the battery.

Note:

• You can find details for using the batteries in the “Notes on Using the

Batteries” ( 158). These notes include charging and recording times and how to install the backup battery.

the Basics

Mastering

Using the Charge Adapter CR-560 Kit (optional)

The Compact Power Adapter CA-560 supplied with the camcorder can be used along with the CR-560 Kit for 3 different ways to power the camcorder or charge battery packs:

1. Charge the BP-500 Series battery packs with power from your car battery.

2. Operate the camcorder with power from your car battery.

3. Charge the BP-500 Series battery packs from a household power socket.

The Charge Adapter/Car Battery Cable Kit CR-560 includes the following:

Charge Adapter

Car Battery Cable

DC Cable

1. Charge the BP-500 Series battery packs with power from your car battery.

1 or 2 battery pack(s) + Charge Adapter + Car Battery Cable → car’s

the Basics

Mastering

cigarette lighter

CHARGE

To car’s cigarette lighter

• Fast charging for the high-capacity BP-522 and BP-535 (both optional). 15 minutes of charging gives 60 minutes of recording (using the viewfinder).

Time required for full charge

from car battery or household outlet BP-512 1 hr. 20 min. BP-511 (optional) 1 hr. 20 min. BP-522 (optional) 1 hr. 40 min. BP-535 (optional) 2 hr. 30 min.

2. Operate the camcorder with power from your car battery.

Camcorder + DC Cable + Charge Adapter + Car Battery Cable → car’s cigarette lighter

To car’s cigarette lighter

3. Charge the BP-500 Series battery packs from a household power socket.

1 or 2 battery pack(s) + Charge Adapter + Compact Power Adapter

CHARGE

• Fast charging for the high-capacity BP-522 and BP-535 (both optional). 15

minutes of charging gives 60 minutes of recording (using the viewfinder).

Notes:

• For full details of how to use the CR-560, refer to its instruction manual.

• Charge the battery pack in temperatures between 41°F and 104°F (5°C

and 40°C).

• The charging time varies depending on the charging conditions.

the Basics

Mastering

Loading a Cassette

OPEN/EJECT

Only use videocassettes marked with the D logo.*

Loading and Unloading

1. Make sure that you have attached a power source.

2. Slide the OPEN/EJECT 5 switch (on the bottom of the camcorder) to release the cassette compartment cover.

• Pull the cover fully open (while holding the button) and wait a couple of

seconds for the cassette compartment to open automatically.

• The confirmation beep sounds when the cassette cover fully opens.

the Basics

Mastering

3. Load or unload the cassette.

• Insert the cassette gently with the window facing the grip belt, and the

REC/SAVE tab up.

• Remove the cassette by pulling it straight out.

4. Press the P mark on the compartment until it clicks, and wait for the compartment to close.

5. Click the cover back into place.

* D is a trade mark.

Notes:

• Do not interfere with the cassette compartment while it is opening or

closing automatically, and do not attempt to close the cover until the cassette compartment has fully retracted.

• Be careful not to get your fingers caught in the cassette compartment cover.

• Do not leave the cassette in the camcorder after use — return it to its case

and store it in a cool, clean, dry place.

• When you turn the camcorder’s power on, v flashes in the display until

you load a cassette.

• With some types of tapes, the remaining tape display may not give an

accurate reading ( 174).

Protecting Tapes from Accidental Erasure

SAVE

REC

SAVE

REC

To protect your recording from accidental erasure, slide the tab on the cassette so that it exposes the hole. (This switch position is usually labelled SAVE or ERASE OFF.) If you load this cassette and put the camcorder in record pause mode ( 20), “THE TAPE IS SET FOR ERASURE PREVENTION” is displayed for approx. 4 seconds and then the v mark flashes in the display. If you want to record on the cassette again, slide the tab back so that the hole is closed.

Cassette Handling Precautions

• To protect the tape heads, transfer cassettes directly from the tape case to

the camcorder — do not open the tape protect cover or touch the tape itself.

• Do not use cassettes where the tape has been damaged or spliced — they

may damage the camcorder.

• Do not insert anything into the small holes on the cassette or cover them

with cellophane tape.

• Handle cassettes with care — dropping them or exposing them to external

shocks may cause internal damage.

• Store cassettes in the provided case, first rewinding them to the start of

the tape and then storing them upright.

• A cassette with metal plated terminals may become dirty with use,

affecting information transfer. Therefore, after using a tape about 10 times, be sure to clean the terminals with a cotton swab.

the Basics

Mastering

Cassette Memory Function

You are unable to use the cassette memory function with this camcorder.

Basic Recording

5, 6

CARD TAPE

(

)

(

)

Before You Start Recording

Have you completed the following steps?

• Attaching a power source ( 13).

• Removing the lens cap ( 157).

• Fastening the grip belt ( 157).

• Attaching the lens hood ( 156).

• Choosing the display: viewfinder ( 156) or LCD screen ( 27).

the Basics

Mastering

Note:

• When you’re using the viewfinder, fully close the LCD or rotate the LCD so that it faces into the same direction as the lens ( 27).

You may also want to install the backup battery ( 160) in order to set the date and time display ( 53).

Recording

1. Press and hold the small button on the POWER switch and

turn the POWER switch to CAMERA.

• The camcorder automatically sets to record pause mode. PAUSE appears in the display.

• If you have not set the date and time display, SET THE TIME ZONE, DATE AND TIME appears in the display. For setting the time zone, see p.

53. For setting the date and time, see p. 55.

• The camcorder power indicator lights up.

• The confirmation beep sounds.

• The camcorder will turn itself off if you leave it in record pause mode for more than about 5 minutes. To return to record pause mode, turn the POWER switch to OFF and then back to CAMERA.

2. Make sure the TAPE/CARD switch is set to TAPE.

• For recording still images onto a memory card, see p.112. For recording movies onto a memory card, see p.117.

3. Load a cassette ( 18).

• Start recording when the tape counter has stopped.

4. Slide the program selector to [.

• This selects the camcorder’s Easy Recording program. It allows you to simply point and shoot without making any manual adjustments ( 62).

5. Press and release the start/stop button once to begin recording.

• For still image recording to a cassette, see p. 56.

6. Press and release the start/stop button again to pause recording.

• The camcorder returns to record pause mode and PAUSE reappears in

the display.

• You can stop and restart recording as often as you like by pressing the

start/stop button.

When you have finished recording

• Replace the lens cap.

• Return the LCD screen flush to the camcorder body.

• Unload the cassette.

• Turn the POWER switch to OFF.

• Disconnect the power source.

the Basics

Mastering

Notes:

• To check that the camcorder is recording correctly, make a test recording first.

• Before making important recordings, clean the video heads using a Canon DVM-CL Digital Video Head Cleaning Cassette or a commercially available digital video head cleaning cassette.

• To close the LCD panel, rotate it vertically until the screen faces you, then press the LCD panel until it clicks securely closed.

• You cannot monitor the sound from the speaker when recording.

• For tips on how to make better videos, see p. 30.

• For extra recording time, see “Changing the Recording Mode” ( 22).

16:9••••••••OFF

CAM.SET UP

CAMERA

TAPE

REC MODE••••SP

VCR SET UP

PLAY

(VCR)

CARD

PLAY

(VCR)

TAPE

CAMERA

TAPE

Changing the Recording Mode

You can select between SP (standard play) and LP (long play). LP extends the tape usage by 1.5 times.

It is not possible to dub audio or insert images to a tape that has been recorded in LP mode.

( 40)

To change to LP mode, open the menu and select VCR SET UP. Then select REC MODE, set it to LP and close the menu.

Notes:

• Depending on the nature and usage condition of the tape, recording/playback in LP mode may cause image or sound distortion. We recommend using the SP mode for important recordings.

• We recommend recording in SP mode when you plan to transfer images

the Basics

Mastering

taken with the camcorder to your PC.

• If you record in both modes on the same tape, the image may become distorted during playback and the time code may not be written correctly.

• If you play back a tape recorded on another digital equipment on this camcorder, or vice versa, image and sound may become distorted.

16:9 (Wide Screen TV Recording)

Produces images in the 16:9 format for playback on wide screen TVs.

( 40)

To switch 16:9 to ON, open the menu and select CAM.SET UP. Then select 16:9, set it to ON and close the menu.

PLAY

(VCR)

CARD

PLAY

(VCR)

TAPE

CAMERA

TAPE

TALLY LAMP••ON

SYSTEM

Notes:

• “16:9” is shown in the display when you switch the 16:9 mode on.

• You cannot use the 16:9 mode with the Easy Recording program.

• You cannot use the multi-image screen when setting the 16:9 mode on.

• If you play back a recording made for 16:9 on a normal TV screen, the image will appear to be vertically “squashed” (compressed).

• If you connect the camcorder to a TV with an S1 terminal or the Video ID1 system, recordings made in the 16:9 mode for wide screen TVs will automatically play back in wide screen mode on the TV screen.

Turning Off the Tally Lamp

The tally lamp lets you know that the camcorder is recording, receiving signals from the wireless controller or counting down for the self-timer. However, its flashing may be reflected into the lens during closeup recording, or when recording through glass.

You may therefore decide to turn it off.

the Basics

Mastering

( 40)

To turn the tally lamp off, open the menu and select SYSTEM. Then select TALLY LAMP, set it to OFF and close the menu.

• The tally lamp no longer flashes during recording, but it will still light up when the camcorder receives a signal from the wireless controller and during the self-timer countdown.

BEEP••••••••ON

SYSTEM

PLAY (VCR)

CARD

CAMERA

CARD

PLAY

(VCR)

TAPE

CAMERA

TAPE

CAMERA

CARD

CAMERA

TAPE

DEMO MODE•••ON

DISP.SET UP

Confirmation/Warning Beeps

The camcorder’s short operation confirmation beeps are indicated by ` in the illustrations. Beeps sound upon certain camcorder operations such as when you turn the camcorder on, during the self-timer countdown, right before the camcorder’s automatic shut-off, and also upon any unusual condition of the camcorder. Beeps are not recorded on the tape.

( 40)

To turn the beep off, open the menu and select SYSTEM. Then select BEEP, set it to OFF and close the menu.

• All camcorder sounds, including the shutter sound that sounds when recording a still image onto a memory card will be turned off.

Demonstration Mode

You can see a demonstration of the camcorder’s main features. To see the

the Basics

Mastering

demonstration, do either of the following:

• With no cassette or memory card inserted, turn the DEMO MODE on in the TAPE CAMERA menu or CARD CAMERA menu and close the menu.

• Leave the camcorder with no cassette or memory card inserted for five minutes after turning it on.

( 40)

To turn the demonstration mode off, open the menu and select DISP. SET UP. Then select DEMO MODE, set it to OFF and close the menu.

Note:

• To cancel the demo mode once it has begun: push any button, turn off the power, load a cassette or insert a memory card.

Zooming

CAMERA

CARD

CAMERA

TAPE

Zoom in

Zoom out

10× Optical Zoom

The camcorder’s zoom lens allows you to choose the best picture angle for each scene:

• Move the zoom control towards W to zoom out to wide-angle.

• Move it towards T to zoom in to telephoto.

You can also control the speed of zooming:

• Move the control slightly to zoom slowly.

• Move it farther to zoom more quickly. (The farther you move the zoom control, the faster the zoom speed.)

The T and W buttons on the wireless controller adjust the picture angle, but not the zoom speed.

40×/200× Digital Zoom (Card 40×)

the Basics

Mastering

Magnifies the camcorder’s zoom range by up to 20× in TAPE CAMERA mode. The zoom control continues to work as usual. You can freely zoom in and out between 1× and 200× magnification — the camcorder automatically switches between optical zooming (up to 10×) and digital zooming (10× to 40× or 10× to 200×).

( 40)

CAM.SET UP

D.ZOOM••••••

40×

To change the digital zoom, open the menu and select CAM.SET UP. Then select D.ZOOM, set it to OFF or 200

× and close the

menu.

the Basics

Mastering

Notes:

• When zooming, as a rule, keep at least 3 ft 33/8 in (1 m) between you and your subject. However when the zoom is at the wide-angle position, you

can focus on a subject as close as

/8 in (1 cm).

• Image resolution is slightly lower when the magnification is greater than 10×.

• You cannot use digital zoom in the Night and Super Night recording program.

• You cannot use digital zoom when the multi-image screen is set. The display becomes “– – –”.

• The zoom indicator appears for 4 seconds. When the digital zoom is set to 40×, the zoom indicator extends (light blue). When the digital zoom is set to 200× zoom, the zoom indicator extends again (a darker blue).

Using the LCD Screen

180°

90°90°

Opening and Closing the LCD Screen

Press the LCD panel OPEN button and open the panel by pulling it away from the camcorder. This automatically switches the LCD screen on and the viewfinder off. Close the LCD panel until it clicks securely closed. When you close the LCD panel, the LCD screen automatically switches off and the viewfinder switches back on.

Changing the Angle of the LCD Screen

You can choose the angle of the screen that suits you best by opening and rotating the screen. You can also rotate the LCD screen so that it faces in the direction of the lens ( 29).

You can also push the panel flat against the camcorder until it is flush with the side, with the screen facing outwards.

the Basics

Mastering

Notes:

• Avoid touching the LCD screen when moving the LCD panel.

• Do not hold the camcorder by the LCD panel or the viewfinder.

• Make sure to open the LCD panel at 90° before attempting to rotate it.

• Always rotate the LCD panel vertically into place before closing it or pushing it flat against the side of the camcorder.

• Always fully close the LCD panel until it clicks securely.

• Be careful not to leave the LCD, viewfinder or lens exposed to direct sunlight outdoors or through a window. Doing so could cause damage.

BRIGHTNESS••

DISP.SET UP

–+

PLAY (VCR)

CARD

CAMERA

CARD

PLAY

(VCR)

TAPE

CAMERA

TAPE

• Bright light falling on the LCD screen may cause glare that makes it

difficult for you to view the image. In this case, switch to using the viewfinder. You can also adjust the brightness of the screen (see “Adjusting the LCD screen” below).

Adjusting the LCD Screen

You can adjust the brightness of the LCD screen.

( 40)

Open the menu and select DISP.SET UP from the menu. Then select BRIGHTNESS, adjust the level with the selector dial and close the menu.

A bar showing the level appears in the display.

• Turn the selector dial up to make the display brighter.

the Basics

Mastering

• Turn the selector dial down to make the display darker.

Notes:

• The camcorder retains your brightness setting even after you turn it off.

• The brightness of the LCD does not affect that of the recorded images or the viewfinder.

About the LCD Screen

The LCD screen built into this camcorder is a high precision product. However, small black dots or bright points of light (red, blue or green) may appear constantly on the LCD screen. This is not a malfunction of the LCD screen and they are not recorded. (Effective dots: more than 99.99%)

Allowing the Subject to Monitor Recording

LCD MIRROR••ON

DISP.SET UP

CAMERA

CARD

CAMERA

TAPE

When you turn the LCD panel so that it faces to the same direction as the lens, you can watch yourself during recording or let your subject monitor recording. The viewfinder is also activated when the panel is in this position. (“Adjusting the Viewfinder” 156)

• You can choose the display style, reversed (mirror on) or not (mirror off). The recording itself is unaffected regardless of which one you choose.

( 40)

To turn the mirror mode off, open the menu and select DISP.SET UP. Then select LCD MIRROR, set it to OFF and close the menu.

The indicators that appear on the LCD screen when LCD MIRROR is turned on:

TAPE CAMERA mode

REC

CARD CAMERA mode

No card Recording to a memory card

REC PAUSE EJECT

CARD CAMERA mode Recording to a memory card

the Basics

Mastering

Tips for Making Better Videos

Holding the camcorder

For maximum stability, grip the camcorder in your right hand and keep your right elbow pressed against your body. If necessary support the camcorder with your left hand. With practice, you will be able to operate the controls by touch, without taking your eye off the action.

Using a Tripod

To prevent any unwanted movement, you can mount the camcorder on a tripod, (or any flat surface at a suitable height) and operate it with the wireless controller.

• When you are using a tripod, be careful not to leave

the viewfinder exposed to bright sunlight as it may melt. (The light is concentrated by the viewfinder lens.)

• Make sure that the fastening screw of the tripod is

Mastering

the Basics

no longer than the camcorder.

/4 inch (5.5 mm), as it will damage

Composition

The most important element in the scene does not have to be in the center. For a more interesting picture, try to position your subject slightly to one side. Leave some space on the side of the frame that the subject is facing or moving towards.

Do not cut off the top of the subject’s head, and do not cut people off at the neck, hips or knees (move a little bit above or below).

Watch out for distracting objects in the background.

+ 162 hidden pages