Canon M11037, DR-3080CII User Manual
Startup Manual
Read this manual thoroughly before using this scanner.
Keep this manual in a safe place for future reference.
International ENERGY STAR® Office Equipment Program
As an E
meets the E
The International E
NERGY STAR partner, Canon Electronics Inc. has determined that this product
NERGY STAR guidelines for energy efficiency.
NERGY STAR Office Equipment Program is an international program
that promotes energy saving through the use of computers and other office equipment.
The program backs the development and dissemination of products with functions that
effectively reduce energy consumption. It is an open system in which business proprietors can participate voluntarily. The targeted products are office equipment such as
computers, monitors, printers, fax machines, copiers and Scanners. Their standards and
logos are uniform among the participating nations.
FCC REGULATIONS (For 120 V/220-240 V models)
Document Scanner, Model M11037
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules.
Do not make any changes or modifications to the equipment unless otherwise specified in the manual. If
such changes or modifications should be made, you could be required to stop operation of the equipment.
Canon U.S.A. Inc.
One Canon Plaza, Lake Success NY 11042, U.S.A.
Te l. No. (516)328-5600
RADIO INTERFERENCE REGULATIONS (For 120 V models)
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as
set out in the Interference-causing equipment standard entitled "Digital Apparatus", ICES-003 of the Industry Canada.
RÈGLEMENT SUR LE BROUILLAGE RADIOÉLECTRIQUE (For 120 V models)
Cet appareil numérique respecte les limites de bruits radioélectriques applicables aux appareils numériques
de Classe B prescrites dans la norme sur le matériel brouilleur: "Appareils Numériques", NMB-003 édictée
par l'Industrie Canada.
Für EMVG
Dieses Produkt ist zum Gebrauch im Wohnbereich, Geschäfts-und Gewerbebereich sowie in Kleinbetrieben
vorgesehen.
Für 3. GSGV
Maschinenlärminformationsverordnung 3. GSGV, 18.01.1991: Der höchste Schalldruckpegel beträgt 70
dB(A) oder weniger gemäß EN 27779.
MODEL NAMES
Model DR-3080CII is identical to model M11037.
READ CAREFULLY BEFORE OPENING THE SEALED DISK PACKAGE
CANON SOFTWARE LICENSE AGREEMENT
IMPORTANT-READ THIS AGREEMENT BEFORE OPENING THE SEALED DISK PACKAGE! BY OPENING
THE SEALED DISK PACKAGE, YOU ARE DEEMED TO AGREE TO BE BOUND BY THIS AGREEMENT.
This legal document is a license agreement between you and Canon Electronics Inc. ("Canon"). BY OPENING THE SEALED DISK
PACKAGE, YOU ARE DEEMED TO AGREE TO BE BOUND BY THE TERMS OF THIS AGREEMENT.
TERMS OF THIS AGREEMENT, DO NOT OPEN THE SEALED DISK PACKAGE AND PROMPTLY RETURN THE CANON SCANNER,
THE DISK PACKAGE CONTAINING SCANNER DRIVER SOFTWARE PROGRAMS AND/OR SCANNER UTILITY SOFTWARE
PROGRAM PROPRIETARY TO CANON OR ITS LICENSOR (THE "SOFTWARE") AND THE ACCOMPANYING DOCUMENTATION
AND OTHER ITEMS TO THE PLACE WHERE YOU OBTAINED THEM FOR A REFUND BEFORE THEY ARE USED OR OPENED OR
UNPACKED.
In consideration of the right to use the SOFTWARE, you agree to abide by the terms and conditions of this Agreement.
1. GRANT OF LICENSE: Canon grants you the personal, non-exclusive right to use the SOFTWARE only on a single computer. You
may physically transfer the SOFTWARE from one computer to another provided that the SOFTWARE is used on only one computer at any time.
You shall not assign, sublicense, sell, rent, lease, loan, convey or transfer to any third party, or send or bring the SOFTWARE out of the
country where you originally obtain it to other countries without required authorization of applicable governments, or copy, duplicate, translate or
convert to another programming language the SOFTWARE or accompanying documentation, except as expressly provided herein.
Except as expressly permitted under the applicable law, you shall not alter, modify, disassemble, decompile or otherwise reverse engineer
the SOFTWARE or accompanying documentation and you also shall not have any third party do so.
2. BACK-UP COPY: You may make one copy of the SOFTWARE solely for a back-up purpose or copy the SOFTWARE onto the
permanent storage device (e.g. a hard disk) of your computer and retain the original for a back-up purpose. Except as expressly permitted under the
applicable law, any other copying of the SOFTWARE is a violation of this Agreement. You must reproduce and include the copyright notice on the
back-up copy.
3. SUPPORT AND UPDATE: Canon, Canon's affiliate, their distributor or dealer is not responsible for maintaining or helping you to
use the SOFTWARE. No updates, fixes or support will be made available for the SOFTWARE.
4. LIMITED WARRANTY AND DISCLAIMER OF INDEMNITY: Canon, Canon's affiliate, their distributor or dealer will not
guarantee uninterrupted service, or absence or correction of errors. Therefore, the SOFTWARE is licensed on an "AS IS" basis without warranty of
any kind. The diskette on which the SOFTWARE is recorded is warranted against defective material or workmanship under normal use for a period
of ninety (90) days from the date you purchased the same as evidenced by a receipt or otherwise. The limited warranty does not apply if the failure
of the diskette resulted from accident, abuse or misapplication of the SOFTWARE and shall not extend to anyone other than the original user of the
SOFTWARE.
CANON, CANON'S AFFILIATE, THEIR DISTRIBUTOR OR DEALER DISCLAIMS ALL IMPLIED WARRANTIES, INCLUDING
ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, WITH RESPECT TO THE SOFTWARE OR
ACCOMPANYING DOCUMENTATION.
NEITHER CANON, CANON'S AFFILIATE, THEIR DISTRIBUTOR NOR DEALER IS LIABLE FOR ANY LOSS OR DAMAGE
INCLUDING CONSEQUENTIAL OR INCIDENTAL LOSS OR DAMAGE SUCH AS LOSS OF PROFITS, EXPENSE OR INCONVENIENCE,
WHATSOEVER CAUSED BY OR ARISING OUT OF THE SOFTWARE, ACCOMPANYING DOCUMENTATION OR THE USE THEREOF.
CANON, CANON'S AFFILIATE, THEIR DISTRIBUTOR OR DEALER SHALL HAVE NO OBLIGATION TO INDEMNIFY YOU
AGAINST ANY CLAIM OR SUIT BROUGHT BY A THIRD PARTY ALLEGING THAT THE SOFTWARE, ACCOMPANYING
DOCUMENTATION OR THE USE THEREOF INFRINGES ANY INTELLECTUAL PROPERTY OF SUCH THIRD PARTY.
THE ABOVE IS CANON'S ENTIRE LIABILITY AND YOUR EXCLUSIVE REMEDY IN CONNECTION WITH THE SOFTWARE
AND ACCOMPANYING DOCUMENTATION.
5. TERM: This Agreement is effective upon opening the sealed disk package and remains in effect until terminated. You may terminate
this Agreement by destroying the SOFTWARE and any copy thereof. This Agreement will also terminate if you fail to comply with any of the
terms of this Agreement. In addition to Canon enforcing its respective legal rights, you must then promptly destroy the SOFTWARE and any copy
thereof.
6. U.S. GOVERNMENT RESTRICTED RIGHTS NOTICE: The SOFTWARE is provided with RESTRICTED RIGHTS. Use,
duplication or disclosure is subject to restrictions as set forth in either subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARs 252.227-7013 or subparagraph (c) (1) and (2) of the Commercial Computer Software Restricted Rights Clause at FAR
52.227-19, as applicable.
7. SEVERABILITY: In the event that provision of this Agreement is declared or found to be illegal by any court or tribunal of
competent jurisdiction, such provision shall be null and void with respect to the jurisdiction of that court or tribunal and all the remaining provisions
of this Agreement shall remain in full force and effect.
8. ACKNOWLEDGEMENT: BY OPENING THE SEALED DISK PACKAGE, YOU ACKNOWLEDGE THAT YOU HAVE READ
THIS AGREEMENT, UNDERSTOOD IT, AND AGREE TO BE BOUND BY ITS TERMS AND CONDITIONS. YOU ALSO AGREE THAT
THIS AGREEMENT IS THE COMPLETE AND EXCLUSIVE STATEMENT OF AGREEMENT BETWEEN YOU AND CANON
CONCERNING THE SUBJECT MATTER HEREOF AND SUPERSEDES ALL PROPOSALS OR PRIOR AGREEMENTS, VERBAL OR
WRITTEN, AND ANY OTHER COMMUNICATIONS BETWEEN YOU AND CANON RELATING TO THE SUBJECT MATTER HEREOF.
NO AMENDMENT TO THIS AGREEMENT SHALL BE EFFECTIVE UNLESS SIGNED BY A DULY AUTHORIZED REPRESENTATIVE
OF CANON.
Should you have any questions concerning this Agreement, or if you desire to contact Canon for any reason, please write to Canon's local affiliate.
IF YOU DO NOT AGREE TO THE
Preface
Thank you for purchasing the Canon DR-3080CII scanner. Be sure to read
this manual thoroughly before using the scanner in order to ensure that you
fully understand how to use the scanner correctly. After you have read this
manual, retain it for future reference.
CAUTION
Be aware of the following points when using this scanner for reproduction:
•Making duplicates of paper currency, coins, government-issued securities and other negotiable instruments is prohibited by law and subject to criminal penalties.
•Making duplicates of government-issued passports as well as licenses, permits, official
documents and private documents issued by public or private institutions may also be subject
to criminal penalties.
•Making duplicates of written works, music, paintings, prints, maps, drawings, movie stills,
photographs and other copyrighted works is prohibited, except when done for personal and
noncommercial purposes.
Copyright
Copyright 2004 by CANON ELECTRONICS INC. All rights reserved. No part of this
publication may be reproduced, transmitted, transcribed, stored in a retrieval system,
or translated into any language or computer language in any form or by any means,
electronic, mechanical, magnetic, optical, chemical, manual, or otherwise, without the
prior written permission of CANON ELECTRONICS INC.
Trademarks
•Microsoft, Windows and Windows NT are registered trademarks of Microsoft Corporation in
the United States and/or other countries.
• ISIS is a trademark of Pixel Translations, A division of Captiva Software Corporation, in the
United Status.
• Intel and Pentium are registered trademarks of Intel Corporation.
•
ENERGY STAR is a U.S. registered mark.
•Adobe is the registered trademark of Adobe Systems Incorporated in the United States and/or
other countries.
•Product names mentioned herein are for identification purposes only and may be trademarks
and/or registered trademarks of their respective companies.
Other Notice
The information given in these operating instructions is subject to change without
notice.
2 Preface
Notational Conventions
The symbols and indications used in this manual are explained below.
Familiarize yourself with these symbols and their meanings before reading
this manual.
WARNING
Indicates a warning concerning operations that may lead to death
or injury to persons if not performed correctly. In order to use the
machine safely, always pay attention to these warnings.
CAUTION
Indicates a caution concerning operations that may lead to injury
to persons, or damage to property if not performed correctly. In
order to use the machine safely, always pay attention to these
cautions.
IMPORTANT
Indicates operational requirements and restrictions. Be sure to read these items
carefully in order to operate the machine correctly, and to avoid damage to the
machine.
Note
Indicates a clarification of an operation, or contains additional explanations
for a procedure. Reading these notes is highly recommended.
Preface 3
Table of Contents
Preface ................................................................................................................. 2
Notational Conventions .......................................................................................... 3
Table of Contents ................................................................................................ 4
Before Using the Scanner .................................................................................. 5
To Ensure Safe Operation ...................................................................................... 5
Installation Location ................................................................................................. 5
Power ....................................................................................................................... 6
Moving the Scanner ................................................................................................. 6
Notes on Normal Handling ....................................................................................... 7
Notes Concerning Disposal ..................................................................................... 8
Features of the DR-3080CII ................................................................................... 9
Checking the Packing List .................................................................................... 11
Removing the Protective Tape and Protective Sheet ............................................. 12
Names and Functions of Parts ............................................................................. 13
Installing the Scanner ....................................................................................... 15
Installation Requirements ..................................................................................... 15
Installation Procedure ........................................................................................... 17
Interface Boards ................................................................................................... 18
SCSI Boards .......................................................................................................... 18
USB 2.0 Interface Board ........................................................................................ 18
Connecting the Scanner to Your PC ..................................................................... 19
Connecting via SCSI .............................................................................................. 19
Connecting via USB ............................................................................................... 21
Connecting the Power Cord ................................................................................. 22
Turning the Power On/Off ..................................................................................... 23
Turning the Power On ............................................................................................ 23
Recognizing the Scanner ....................................................................................... 23
Turning the Power Off ............................................................................................ 25
Installing the Software ...................................................................................... 26
Installing the ISIS/TWAIN Driver .......................................................................... 26
Uninstalling the ISIS/TWAIN Driver ...................................................................... 29
Installing CapturePerfect ...................................................................................... 32
Uninstalling CapturePerfect .................................................................................. 33
Using the Software............................................................................................ 35
Using the ISIS/TWAIN Driver ............................................................................... 35
Using CapturePerfect ........................................................................................... 36
Starting CapturePerfect ......................................................................................... 36
Closing CapturePerfect .......................................................................................... 37
Using the Scanner............................................................................................. 38
Documents ........................................................................................................... 38
Setting Up the Paper Feed Tray and the Document Eject Tray ........................... 39
Installing the Document Eject Guide .................................................................... 41
Loading a Document for Scanning ....................................................................... 43
Automatic Feeding ................................................................................................. 43
Manual Feeding ..................................................................................................... 46
Scanning Folio (Folded Documents) ...................................................................... 47
Patch Code Sheets .............................................................................................. 48
About Patch Code Sheets ...................................................................................... 48
Functions of Patch Code Sheets ........................................................................... 49
Using Patch Code Sheets ...................................................................................... 49
Effective Area for Detecting Patch Code Patterns ................................................. 50
Clearing a Paper Jam ........................................................................................... 51
Regular Maintenance ........................................................................................ 54
Cleaning the Scanner ........................................................................................... 54
Cleaning the Scanning Glass and the Rollers ...................................................... 55
Troubleshooting ................................................................................................ 56
Specifications .................................................................................................... 63
Index ................................................................................................................... 66
4 Table of Contents
Before Using the Scanner
To Ensure Safe Operation
In order to ensure safe operation, be certain to read the cautions described
below.
Installation Location
At least 3.9” (100 mm)
14.9” (378 mm)
when paper feed
tray and paper
feed tray
extension are
closed
25.8” (655 mm) when
paper feed tray and
paper feed tray
extension are open
The performance of this scanner is affected by the environment in which it is
installed. Make sure that the location where the scanner is installed meets the
following environmental requirements.
● Provide adequate space around the scanner (as indicated in the above
diagram) for operation, maintenance and ventilation purposes.
● Avoid locations exposed to direct sunlight. If the scanner must be placed in
such a spot, hang a heavy curtain, etc., to shade the scanner.
● Avoid dusty locations. Dust can get inside of the scanner and cause
problems.
● Avoid warm or humid locations, such as in the vicinity of a water faucet,
water heater, humidifier, etc., and avoid locations where the fumes from
ammonia, paint thinner, etc., may be present.
● Avoid unstable surfaces and locations subject to vibration.
Before Using the Scanner 5
● Avoid locations that are subject to rapid temperature changes.
Condensation inside of the scanner can result in inferior image quality. Use
this scanner under the following environmental conditions:
Temperature: 10˚C to 32.5˚C (50˚F to 90.5˚F)
Humidity: 20% to 80% RH
● Avoid locating the scanner near equipment that generates electromagnetic
fields, including speakers, televisions, and radios.
Power
● Before you plug the power cord into an outlet, be sure that the power
source meets the requirements of the scanner.
● Do not connect this scanner to a power outlet that is shared with other
equipment. When using an extension cord, make sure that the extension
cord is rated for the current requirements of the scanner.
● Do not place other objects on the power cord. Do not step on the power
cord.
● Do not bundle the power cord, and do not wrap the power cord around a
table or chair leg.
● Do not pull on the power cord. Always grasp the plug when unplugging the
power cord.
● Do not place other objects around the outlet.
● If you have any questions concerning your local power supply, contact
your local authorized Canon dealer or your local power company.
Moving the Scanner
● To avoid dropping or damaging the scanner, always carry it with two
hands. The scanner weighs approximately 17.8 lb (8.1 kg).
● Make sure to disconnect the interface cable and power cord. If the scanner
is transported with these items plugged in, the plugs and connectors may be
damaged due to physical shock or concussion.
6 Before Using the Scanner
Notes on Normal Handling
WARNING
To avoid fire and electric shock, always observe the following
warnings when using this scanner.
■ Do not place flammable chemicals, such as alcohol or paint thinner, near
the scanner.
■ Do not cut, damage, or modify the power cord. Do not place heavy objects
on the power cord, do not pull on the power cord, and do not bend the
power cord sharply.
■ Do not plug in or unplug the power cord with wet hands.
■ Do not use multi-outlet adapters to connect multiple devices to one outlet.
■ Do not tie up or bundle the power cord. Push the plug in as far as it will go
when plugging in the power cord.
■ Only use the power cord that was provided with this scanner.
■ Do not attempt to disassemble or modify this scanner.
■ Do not use flammable sprays near this scanner.
■ Always turn the scanner off and unplug the power cord before cleaning this
scanner.
■ To clean this scanner, dampen a cloth in a mild detergent solution and then
wring the cloth out thoroughly. Do not use flammable liquids to clean the
scanner, including alcohol, benzene, or paint thinner.
■ If the scanner ever makes a strange noise, emits smoke or a strange odor, or
becomes hot, or if the scanner does not operate at all even though the
power is on, immediately turn the scanner off and unplug the power cord.
Contact your local authorized Canon dealer or service representative to
have the scanner serviced.
■ Do not drop, kick, or otherwise strike the scanner. If the scanner does
somehow become damaged, immediately turn the scanner off and unplug
the power cord. Contact your local authorized Canon dealer or service
representative to have the scanner serviced.
■ Always turn the scanner off and unplug the power cord before moving the
scanner.
Before Using the Scanner 7
CAUTION
■ Do not set the scanner up on a wobbly platform, a sloped surface, or any
other type of unstable location. Do not set up the scanner in a location that
is subject to vibration. The scanner could injure someone if it falls or tips
over.
■ Do not block the ventilation openings. Doing so could cause the scanner to
overheat, creating a risk of fire.
■ Do not place paper clips, staples, necklaces or any other metallic objects on
top of the scanner. Liquids or small metallic objects that get inside of the
scanner create a risk of fire or electric shock. If such foreign matter does
get inside of the scanner, unplug the power cord immediately, and then
contact your local authorized Canon dealer or service representative for
assistance.
■ Do not set up the scanner in a dusty or humid location. Doing so creates a
risk of fire or electric shock.
■ Do not place objects on top of the scanner. The object could injure
someone if it falls or tips over.
■ To prevent any risk of fire or electric shock, be sure that the power source
meets the power requirements of the scanner.
■ When unplugging the power cord, always grasp the plug. Pulling on the
cord itself could expose or break the wires in the power cord, damaging the
cord and creating a risk of fire or electric shock.
■ In order to allow you to easily unplug the power cord at any time, do not
place other objects around the power outlet. Such obstacles could prevent
you from unplugging the power cord quickly in an emergency.
■ Do not spill liquids or flammable chemicals (such as alcohol, paint thinner,
or benzene) on the scanner. Doing so creates a risk of fire or electric shock.
■ If the scanner will not be used for an extended period of time, unplug the
power cord for safety’s sake.
■ When operating this scanner, avoid wearing loose-fitting clothing, dangling
jewelry, or other material that could get pulled into the scanner. Injury
could result. Be especially careful if you are wearing a necktie or have long
hair. In the event that some article or clothing does get caught in the
scanner, turn the power off immediately.
■ Be careful when placing paper in the scanner and when removing jammed
paper. It is possible to cut your hand on the edge of a sheet of paper.
Notes Concerning Disposal
CAUTION
Always follow the appropriate municipal by-laws or consult your service
center when disposing of the scanner.
8 Before Using the Scanner
Features of the DR-3080CII
The main features of the DR-3080CII scanner are listed below.
■ Fast Document Feeding
Although the scanner is compact, it can rapidly scan up to forty A4 sheets
(both sides) per minute, and can scan documents ranging in size from
business cards to B4 size documents.
■ Compact Size
The scanner is extremely compact, 13.5” x 10.9” x 7.5” (W x H x D).
344 mm x 278 mm x 191 mm(W x H x D).
■ SCSI/USB 2.0 Interface supported
The scanner is equipped with both SCSI and Hi-Speed USB 2.0 interfaces
for connecting to a personal computer.
■ Color/grayscale support
Documents can be scanned in 24-bit color or 256-level grayscale.
■ Supports a Variety of Scanning Modes*
The scanner supports the following scanning modes, depending on the
document type:
● Single-sided/double-sided mode
● Single-sheet/continuous feed
■ Automatic Document Size Detection*
The scanner automatically detects the size of a scanned document and
eliminates any unnecessary space around the edges of the document when
storing it, even when storing a document of irregular size.
■ Folio Scan
A folio (folded in half) document can be set for scanning as it is and the
scanned images of both sides are put together in a page.
■ Dropout Color
The scanner is equipped with a “dropout color” function that allows you to
specify a color for the scanner to omit from scanned images. (This
correction is made by the ISIS/TWAIN driver.)
■ Deskew
The deskew function automatically straightens an image if the document
was loaded askew. (This correction is made by the ISIS/TWAIN driver.)
■ Advanced Text Enhancement
The scanner is equipped with an “Advanced Text Enhancement” mode that
allows you to clearly scan text printed on a dark background, and text that
is written in faint pencil. (This function is implemented by the ISIS/
TWAIN driver.)
* Available when using applications that support these functions.
Before Using the Scanner 9
■ Skip Blank Page Function
The scanner is equipped with a skip blank page function that allows it to
scan a document regardless of whether every page is double-sided or
single-sided. (This function is implemented by the ISIS/TWAIN driver.)
■ Pre-Scan Function
The scanner is equipped with a pre-scan function that allows you to adjust
the contrast and brightness of a pre-scanned image and then sends the
adjusted image to the application software, without needing to scan the
document again. (This function is implemented by the ISIS/TWAIN
driver.)
■ Auto Start
The scanner is equipped with an auto start function that automatically
initiates scanning when a document is placed in the document feed port.
(This function is implemented by the ISIS/TWAIN driver.)
■ Compatible with Carbonless Duplicating Paper
The scanner is able to scan carbonless duplicating paper.
■ Power-saving Feature
The scanner has a power-saving feature that puts the scanner in low-power
mode after it has been idle for a certain period of time.
10 Before Using the Scanner
Checking the Packing List
The contents of the carton in which this scanner is shipped are described
below. If anything is missing or damaged, contact your local authorized
Canon dealer or service representative.
q USB Cable w Document Eject Guide
e Auxiliary Paper Support Plate r Setup Disc (CD-ROM)
t Startup Manual (This Manual) y Quick Reference Guide
u Warranty Card (U.S.A. and Canada only)
i Adjustment Sheet o Power Cord !0 Scanner
• The contents of the carton are subject to change without notice.
• Keep the carton and the packing material for future use if it is ever
necessary to store or transport the scanner.
Before Using the Scanner 11
Removing the Protective Tape and Protective Sheet
Before using the scanner, remove the protective tape and protective sheet that
protect the scanner from damage during shipment.
1.
Remove the protective tape that is attached to the exterior of the scanner.
2.
Open the paper feed tray and remove the protective tape that is inside the
scanner.
3.
Gently raise the upper unit and remove the protective sheet.
After removing the protective sheet, return the upper unit to its original
position.
12 Before Using the Scanner
Names and Functions of Parts
This section explains the name and function of each part. Familiarize yourself
with the parts before connecting the scanner.
■ Front
Paper Feed Tray
■ Front (with Cover Open)
Paper Feed Tray
Place the document
to be scanned here.
Paper Feed Tray
Extension
Pull this tray out if
the document hangs
over the edge of the
main tray.
B
4
A
L
4
T
R
Power Indicator
This indicator lights
when the scanner is
turned on.
Power Switch
This switch is used to
turn the scanner on.
Document Eject Tray Extension
This guide holds ejected documents.
Document Eject Tray
Scanned documents
are ejected here.
Document Eject Guide
Attachment Holes
Attach the document
eject guide to these
holes.
Document Positioning Mark
Align the document guides with the
mark that corresponds to the size
of the document to be scanned.
Paper Side Guides
Adjust the positions of these guides
according to the width of the document to
be scanned.
Before Using the Scanner 13
■ Rear
Power Cord Connector
Connect to the power cord.
Ventilation Openings
USB Connector
Connect to a Hi-Speed
USB 2.0 compatible
cable.
DIP Switches
Set the SCSI ID.
SCSI Connector
Connect to a 50-pin half-pitch (pin
type) SCSI cable.
CAUTION
Do not block the ventilation openings. Doing so could cause the
scanner to overheat, creating a risk of fire.
14 Before Using the Scanner
Installing the Scanner
Installation Requirements
In order to use the DR-3080CII, your computer must satisfy the following
system requirements:
● IBM PC/AT-compatible that satisfies the following specifications:
•Intel Celeron 733 MHz or faster
• Main memory: 256 MB or more (recommended)
• Hard disc space: 400 MB or more
● SCSI board or USB 2.0 interface board that supports the scanner (See
“Interface Board” on p.18)
● Display that is capable of resolution of 1024 x 768 (XGA) or better
(recommended)
● One of the following operating systems, running normally:
Connecting via SCSI
•Microsoft Windows 98 SE
•Microsoft Windows Me
•Microsoft Windows NT 4.0 Workstation
•Microsoft Windows 2000 Professional SP4
•Microsoft Windows XP Professional SP1
Connecting via USB 2.0
•Microsoft Windows 98 SE
•Microsoft Windows Me
•Microsoft Windows 2000 Professional SP4
•Microsoft Windows XP Professional SP1
● ISIS-compatible or TWAIN-compatible application software that runs
normally on your operating system
IMPORTANT
● If you are connecting the scanner via USB 2.0 interface, be sure to use an
updated version of the USB 2.0 driver. For details on the updated driver,
contact your local authorized Canon dealer.
● If your CPU, memory or SCSI board does not meet the recommended
specifications, you may experience problems such as a slower scanning
speed.
Note
● Be sure to allocate sufficient virtual memory.
● Use a SCSI board recommended for use with the scanner.
Installing the Scanner 15
● After checking the shape of the connectors on the computer connected to
the scanner and SCSI device, purchase a SCSI cable with the right
combination of connectors. (See “Connecting the Scanner to Your PC” on
p.19)
● The USB cable you are using should be the one originally bundled with the
scanner or a Hi-Speed USB 2.0-compatible cable.
● Depending on the application software that you are using, the device driver
provided may not operate, or you may not be able to use the functions
described in this guide.
● Make sure that the device driver and application software that you will be
using are compatible with your PC, the system configuration, and the type
of SCSI board that you are using.
● The ISIS/TWAIN driver provided with the scanner is not necessarily
compatible with all ISIS-compatible or TWAIN-compatible application
software. For details, contact your application software dealer.
16 Installing the Scanner
Installation Procedure
The procedure for installing the scanner is outlined below. (For a detailed
outline of this procedure, see “Connecting the Scanner to Your PC” at the end
of this section.)
1. Check the interface board in your computer.
(See “Interface Boards” on p.18)
↓
2. Connect the scanner to the PC.
(See “Connecting the Scanner to Your PC” on p.19)
↓
3. Connect the power cord to the scanner.
(See “Connecting the Power Cord” on p.22)
↓
4. Turn the scanner on first, and then start up the PC.
(See “Turning the Power On” on p.23)
↓
5. Let the PC recognize the Scanner.
(See “Recognizing the Scanner” on p.23)
↓
6. Turn the scanner off. (See “Turning the Power Off” on p.25)
Installing the Scanner 17
Interface Boards
An interface board is needed to connect the scanner to your computer. There
are two types of interface boards. These interface boards are described below
with recommendations for manufacturers and models.
SCSI Boards
When connecting the scanner via SCSI, verify that the SCSI board you are
using is one recommended for use with the scanner. The recommended SCSI
boards are as follows:
Recommended SCSI boards
Manufacturer: Adaptec
Models: AHA-2930U, AHA-2940AU, ASC-19160,
ASC-29160, APA-1480
IMPORTANT
When installing the SCSI board in your computer, please refer to the
computer user’s guide and follow the instructions provided
USB 2.0 Interface Board
When connecting the scanner via USB, verify that the USB 2.0 interface
board you are using is one recommended for use with the scanner. The
recommended USB 2.0 interface boards are as follows:
Recommended USB 2.0 Interface boards
Manufacturer: Adaptec
Models: USB 2 connect 2000LP (AUA-2000)
USB 2 connect 3100 (AUA-3100LP)
USB 2 connect 5100 (AUA-5100)
USB 2 connect for Notebooks (AUA-1420)
IMPORTANT
● When installing the USB 2.0 interface board in your computer, please refer
to the computer user’s guide and follow the instructions provided.
● Make sure that the USB driver is an updated version provided by Adaptec
or Microsoft.
Note
● The DR-3080CII passed the Hi-Speed USB 2.0 certification test. However,
when you use the scanner with a personal computer equipped with USB 2.0
as standard, the scanner may not always operate normally.
● If the interface is not Hi-Speed USB 2.0 compatible, the scanning speed
will slow down.
18 Installing the Scanner
Connecting the Scanner to Your PC
There are two ways of connecting the scanner to your computer, via SCSI or
via USB. Choose whichever format is suitable for the environment in which
you are using your PC.
IMPORTANT
● When the application is running, do not turn the scanner off nor unplug the
interface cable.
● Do not connect both a SCSI cable and a USB cable concurrently.
● Do not connect multiple DR-3080CIIs to one (1) computer.
● When having changed the connection, be sure to turn the scanner and the
PC on once again.
Connecting via SCSI
Notes on the Shape of Connectors and the SCSI Cable
• The DR-3080CII is equipped with a 50-pin half-pitch (pin type) SCSI
connector.
•After checking the shape of the SCSI connector on your computer and
connected SCSI device, purchase a SCSI cable with the right
combination of connectors.
Computer
DR-3080CII
SCSI Device
50-Pin Half-Pitch
(Pin Type)
SCSI Cable
Installing the Scanner 19
IMPORTANT
● Make sure that the scanner and your PC are both turned off when
connecting the scanner to the PC.
● The factory default setting for the terminator of the scanner is set to ON as
default. Be sure to turn off all terminators of the SCSI devices connected
between the scanner and the PC.
Note
The factory default setting for the SCSI ID is “2”.
You can set the SCSI ID by using the DIP-switch provided on the rear side of
the scanner. In the DIP-switch settings, the SCSI ID can be set to ON by
turning the switch to the upper position, or OFF by turning it to the lower
position.
Default Settings
(SCSI ID = 2)
2
1
ON
DIP Switch
Refer to the following table when setting the SCSI ID. If there are other SCSI
devices connected to or inside the PC, make sure to set a unique ID for the
scanner.
SCSI ID SW1 SW2
2 OFF OFF
3 OFF ON
4ONOFF
5ONON
20 Installing the Scanner
Loading...