Canon LV-7525 User Manual

E
English
Multimedia Projector
Owner’s Manual
LV-7525U
2
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
power outlet. Do not try to defeat this safety feature. This projector produces intense light from the projection lens. Do not stare directly into the lens as possible eye
damage could result. Be especially careful that children do not stare directly into the beam.
The Remote Control Unit, supplied to this projector, emits the laser beam as the Laser Pointer function from the Laser Light Window while pressing the LASER button (for 1 minute). Do not look into the Laser Light Window or shine the laser beam on yourself or other people. Eye damage may result.
This projector should be set in the way indicated. If not, it may result in fire hazard. If the Projector will not be used for an extended time, unplug the new Projector from the power outlet.
READ AND KEEP THIS OWNER'S MANUAL FOR LATER USE.
As the owner of a new Multi-media Projector, you are probably eager to try out your new projector. Before you do, we suggest that you spend a little time reading this manual to familiarize yourself with the operating procedures, so that you will receive maximum satisfaction from the many features included in your new projector. This owner's manual will acquaint you with your projector's features. Reading it will help us too. Through the years, we have found that many service requests were not caused by problems with our projectors. They were caused by problems that could have been prevented, if the owner had followed the instructions in the manual. You can often correct operating problems yourself. If your projector fails to work properly, see "TROUBLESHOOTING" section on pages 51 ~ 52 and try the solutions marked for each problem.
SAFETY PRECAUTIONS
TO THE OWNER
INFORMATION TO THE USER
NOTE : This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE EXCEPT LAMP REPLACEMENT. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT.
THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE OWNER'S MANUAL WITH THIS UNIT.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
PROJECTOR
(FRONT)
PROJECTOR
(SIDE)
WALL
50cm
20cm
50cm50cm
Unplug this projector from wall outlet and refer servicing to qualified service personnel under the following conditions:
a. When the power cord or plug is damaged or frayed. b. If liquid has been spilled into the projector. c. If the projector has been exposed to rain or water. d. If the projector does not operate normally by following the
operating instructions. Adjust only those controls that are covered by the operating instructions as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the projector to normal operation.
e. If the projector has been dropped or the cabinet has been
damaged.
f. When the projector exhibits a distinct change in
performance-this indicates a need for service.
When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or injury to persons.
Upon completion of any service or repairs to this projector, ask the service technician to perform routine safety checks to determine that the projector is in safe operating condition.
This projector is equipped with a grounding type AC line plug. Should you be unable to insert the plug into the outlet, contact your electrician. Do not defeat the safety purpose of this grounding type plug.
Follow all warnings and instructions marked on the projectors.
For added protection to the projector during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet. This will prevent damage due to lightning and powerline surges.
An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.
If the projector is to be built into a compartment or similarly enclosed, the minimum distances must be maintained.
Do not cover the ventilation slot on the projector. Heat build-up can reduce the service life of your projector,
and can also be dangerous.
3
IMPORTANT SAFETY INSTRUCTIONS
All the safety and operating instructions should be read before the product is operated.
Read all of the instructions given here and retain them for later use. Unplug this projector from AC power supply before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.
Do not use attachments not recommended by the manufacturer as they may cause hazards.
Do not place this projector on an unstable cart, stand, or table. The projector may fall, causing serious injury to a child or adult, and serious damage to the projector. Use only with a cart or stand recommended by the manufacturer, or sold with the projector. Wall or shelf mounting should follow the manufacturer's instructions, and should use a mounting kit approved by the manufacturer.
Do not expose this unit to rain or use near water... for example, in a wet basement, near a swimming pool, etc...
Slots and openings in the back and bottom of the cabinet are provided for ventilation, to insure reliable operation of the equipment and to protect it from overheating.
The openings should never be covered with cloth or other material, and the bottom opening should not be blocked by placing the projector on a bed, sofa, rug, or other similar surface. This projector should never be placed near or over a radiator or heat register.
This projector should not be placed in a built-in installation such as a bookcase unless proper ventilation is provided.
This projector should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supplied, consult your authorized dealer or local power company.
Do not overload wall outlets and extension cords as this can result in fire or electric shock. Do not allow anything to rest on the power cord. Do not locate this projector where the cord may be damaged persons walking on it.
Never push objects of any kind into this projector through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the projector.
Do not attempt to service this projector yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
GROUND
4
TABLE OF CONTENTS
PAGE
PAGE
MENU OPERATION 30-31
MODE SELECT 30 SOUND ADJUSTMENT 31 LANGUAGE ADJUSTMENT 31
VIDEO MODE 32-35
COLOR SYSTEM SELECT 32 VIDEO SOURCE SELECT 33 PICTURE IMAGE ADJUSTMENT 34 PICTURE SCREEN ADJUSTMENT 35
COMPUTER MODE 36-48
COMPUTER SYSTEM SELECT 36 COMPATIBLE COMPUTER SPECIFICATIONS 37 AUTO IMAGE FUNCTION 38 PICTURE IMAGE ADJUSTMENT 39 PICTURE POSITION ADJUSTMENT 40 PC ADJUSTMENT 41-44 PICTURE SCREEN ADJUSTMENT 45
OTHER FUNCTION SETTING 46-48
BLUE BACK 46-47 DISPLAY 46-47 CEILING 46-47 REAR 46-47 SPLIT WIPE 46-47 POWER MANAGEMENT 46-47 REMOTE CONTROL (Mode 1 or Mode 2) 46-47 LAMP AGE 48
APPENDIX 49-53
MAINTENANCE 49-51
TEMPERATURE WARNING INDICATOR 49 AIR FILTER CARE AND CLEANING 49 LAMP REPLACEMENT 50 CLEANING THE LENS 51
TROUBLESHOOTING 51-52 OPTIONAL PART 52 TECHNICAL SPECIFICATIONS 53
FEATURES AND DESIGN 5
COMPATIBILITY 5 IMAGE RESOLUTION 5
AUTOMATIC MULTISCANNING SYSTEM 5 MULTILANGUAGE MENU DISPLAY 5 TURBO BRIGHT SYSTEM 5
LASER POINTER FUNCTION 5 OTHER FEATURES 5 UNPACKING THE PROJECTOR 5 TRADEMARKS 5
INSTALLATION 6-9
NAME OF EACH PART OF THE PROJECTOR 6 SETTING-UP THE PROJECTOR 7 MOVING THE PROJECTOR 8 POWER REQUIREMENTS 9
CONNECTING THE PROJECTOR 10-18
TERMINAL OF THE PROJECTOR 10 CONNECTING THE COMPUTER 11-15 CONNECTING THE VIDEO EQUIPMENT 16-18
BEFORE OPERATION 19-26
CONTROLS AND INDICATORS 19-20 OPERATION OF THE REMOTE CONTROL 21-23
CONTROL THE PROJECTOR 24-26
DIRECT OPERATION 24 MENU OPERATION 25-26
BASIC OPERATION 27-31
TURNING ON/OFF THE PROJECTOR 27 DIRECT OPERATION 27-29
MODE SELECT 27 SOUND VOLUME ADJUSTMENT 28 SOUND MUTE FUNCTION 28 ZOOM ADJUSTMENT 28 FOCUS ADJUSTMENT 28 DIGITAL ZOOM FUNCTION 28 KEYSTONE FUNCTION 28 NO SHOW FUNCTION 29 FREEZE PICTURE FUNCTION 29 AUTO IMAGE FUNCTION 29 NORMAL PICTURE FUNCTION 29 P-TIMER FUNCTION 29 BRIGHT SWITCH 29
5
FEATURES AND DESIGN
The projector is a multimedia projector that combines powerful and sophisticated features with easy-to-use, intuitive controls. Built-in multimedia features include audio, a palette of 16.77 million colors and active matrix liquid crystal display (LCD) technology. The projector is ideal for high-performance business, training and imaging applications that demand exceptional color quality.
COMPATIBILITY
IMAGE RESOLUTION
UNPACKING THE PROJECTOR
TRADEMARKS
AUTOMATIC MULTISCANNING SYSTEM
MULTILANGUAGE MENU DISPLAY
The projector is compatible with many different types of personal computers and video devices, including:
IBM-compatible computers, including laptops, up to 1280 x 1024 resolution.
Apple Macintosh and PowerBook computers up to 1280 x 1024 resolution.
Various VCRs, video disc players, video cameras, DVD players, satellite TV tuners or other AV equipment using any of the worldwide video standards, including NTSC, NTSC4.43, PAL, PAL-M, PAL-N and SECAM.
The resolution of the projector's projected image is 1024 x 768. The projector displays computer images just as they appear on your computer's monitor. Screen resolutions between 1024 x 768 and 1280 x 1024 are compressed to 1024 x 768. The projector cannot display screen resolutions above 1280 x 1024. If your computer's screen resolution is higher than 1280 x 1024, reset it to a lower resolution before you connect the projector.
This projector can detect display signals from most personal computers currently distributed. It is free from complicated adjustments to project picture images from PC.
The projector comes with the parts listed below. Check to find all the parts are included. If any parts are missing, contact an authorized dealer or service station.
Owner's Manual.
Warranty Card.
AC Power Cord.
Remote Control Unit.
Batteries for Remote Control Units.
VGA Cable.
Mouse Cable for PS/2 port.
Mouse Cable for serial port.
Mouse Cable for ADB port.
VGA/Macintosh Adapter.
Protective Dust Cover.
Lens Cover.
Apple, Macintosh, and PowerBook are trademarks or
registered trademarks of Apple Computer, Inc.
IBM and PS/2 are trademarks or registered trademarks of International Business Machines, Inc.
Windows is a trademarks or registered trademarks of Microsoft Corporation.
Other trademarks are the property of their respective owners
LASER POINTER FUNCTION
The Remote Control Unit of this projector includes the Laser Pointer function providing the ability to point and highlight during presentations.
OTHER FEATURES
This projector has Motor Zoom/Focus, No Show, Picture Freeze, Keystone, Mute Functions.
MENU DISPLAY is displayed with ; English, German, French, Italian, Spanish and Japanese.
TURBO BRIGHT SYSTEM
Brightness of 2750 ANSI lumens (Brighter mode), the highest available in portable models, is achieved. (2200 ANSI lumens in the standard mode).
6
EXHAUST VENT
CAUTION HOT AIR! Air blown from the exhaust vent is hot. Observe the following when handling your
projector or choosing a location to install it.
Keep heat-sensitive objects away from the exhaust port.
If you set the projector on top of a metallic surface, the surface will become hot because of the hot air exhaust. Be careful when handling.
Do not touch the cabinet near to the exhaust vent area, and especially screws and metallic parts. These parts will become hot while the projector is used.
FRONT OF THE PROJECTOR
REAR OF THE PROJECTOR
SPEAKERS
INFRARED REMOTE RECEIVER
PROJECTION LENS
REMOVABLE LENS COVER
INFRARED REMOTE RECEIVER
MAIN ON/OFF SWITCH
CARRYING HANDLE
POWER CORD CONNECTOR
ADJUSTABLE FEET
AIR INTAKE VENT
BOTTOM OF THE PROJECTOR
LAMP COVER
NAME OF EACH PART OF THE PROJECTOR
INSTALLATION
AIR INTAKE VENT
FEET LOCK LATCH
FEET LOCK LATCH
BRIGHT SWITCH
AIR INTAKE VENT
100"
60"
40"
150"
200"
250"
77"
46"
31"
115"
154"
192"
H1
H2
231"
300"
400"
308"
7
POSITIONING:
ROOM LIGHT
This projector is basically designed to project on a flat projection surface.
This projector can be focused from 4.6' (1.4 m) ~ 47.3' (14.4 m).
Refer to the figure below as an example when positioning the projector to the screen.
The level of brightness in a room has a great influence on picture quality. It is recommended to limit ambient lighting in order to provide the best image.
Tele Zoom
Wide Zoom
DISTANCE
SETTING-UP THE PROJECTOR
INSTALLATION
This projector is equipped with cooling fan to protect it from overheating. Pay attention to the following to ensure proper ventilation and avoid a possible risk of fire and malfunction.
Do not cover the vents with papers or other materials.
Keep the rear grill at least 3 feet (1 m) away from any object.
Make sure that there are no objects under the projector. An object under the projector may prevent the projector from taking the cooling air through the bottom vent.
VENTILATION
AIR INTAKE VENT (BOTTOM SIDE)
EXHAUST VENT (REAR SIDE)
400" 308"
47.3' (14.4m)
Screen Size
Wide Zoom
Tele. Zoom
Distance
40" 31"
4.6' (1.4m)
60" 46"
7.2' (2.2m)
100"
77"
11.8' (3.6m)
150" 115"
17.7' (5.4m)
200" 154"
23.6' (7.2m)
250" 192"
29.5' (9.0m)
300" 231"
35.4' (10.8m)
Screen Size
(W x H) inch
Height (H1) Height (H2)
40"
32 x
24
22.8 inch
1.2 inch
60"
48 x 36
34.2 inch
1.8 inch
100"
80 x 60
57.1 inch
2.9 inch
150"
120 x 90
85.7 inch
4.3 inch
200"
160 x 120
114.3 inch
5.7 inch
250"
200 x 150
142.8 inch
7.2 inch
300"
240 x 180
171.4 inch
8.6 inch
400"
320 x 240
228.6 inch
11.4 inch
CAUTION IN CARRYING OR TRANSPORTING THE PROJECTOR
Do not drop or bump the projector, otherwise damages or malfunctions may result.
When transporting the projector, use a Carrying case recommended by Canon.
Do not transport the projector by using a courier or transport service in an unsuitable transport case. This may cause
damage to the projector. To transport the projector through a courier or transport service, use a case recommended by Canon.
For a carrying or transportation cases, contact a Canon authorized dealer.
DOWN
8
Use the carrying handle when moving the projector. Replace the lens cover and retract the adjustable feet when moving the projector to prevent damage to the projector.
Picture tilt and projection angle can be adjusted by rotating the ADJUSTABLE FEET. Projection angle can be adjusted 0 to 6°.
ADJUSTABLE FEET
ADJUSTABLE FEET
FEET LOCK LATCHES
MOVING THE PROJECTOR
INSTALLATION
Lift the front of the projector and press the FEET LOCK LATCHES on both sides of the projector.
Release the FEET LOCK LATCHES to lock the ADJUSTABLE FEET and rotate the ADJUSTABLE FEET to fine tune the position and the tilt.
To shorten the ADJUSTABLE FEET, lift the front of the projector and press and undo the FEET LOCK LATCHES.
1.
3.
2.
UP
UP
DOWN
NOTE: The position and the keystone distortion of the image can
also be adjusted using the KEYSTONE function.
(See pages 28, 35 and 45).
9
INSTALLATION
POWER REQUIREMENTS
Your projector uses nominal input voltages of 100-120 VAC. The projector automatically selects the correct input voltage. The projector is designed to work with single-phase power systems having a grounded neutral conductor. To reduce the risk of electrical shock, do not plug into any other type of power system. Consult your authorized dealer or service station if you are not sure what type of power is supplied to your building.
Connect the AC power supply cord (supplied) to the projector. The socket-outlet must be near this equipment and must be easily accessible.
Projector side (Female)
AC outlet side (Male)
10
REAR OF THE PROJECTOR
COMPUTER INPUT-1 TERMINAL
Used to connect a computer to the projector.
COMPUTER INPUT-2 TERMINAL
Used to connect a computer to the projector.
MONITOR OUTPUT TERMINAL
Used to connect a monitor to the projector.
COMPUTER AUDIO INPUT-1 JACK mini stereo type
Used to connect a computer audio input to the projector.
CONTROL PORT-1 CONNECTOR
Used to connect a mouse cable to the projector.
COMPUTER AUDIO INPUT-2 JACK mini stereo type
Used to connect a computer audio input to the projector.
CONTROL PORT-2 CONNECTOR
Used to connect a mouse cable to the projector.
NOTE: Control port-2 connector can be also used as
serial port (RS-232C).
AUDIO INPUT JACKS
Used to connect an audio input to the projector.
VIDEO INPUT JACK
Used to connect a video source to the projector.
S-VIDEO INPUT JACK
Used to connect a S-video source to the projector.
COMPONENT VIDEO INPUT JACKS
Used to connect a component video source to the projector.
EXT. SP. JACK (3.5 mm mini stereo type)
Used to connect an external speaker system.
Y Cb/Pb Cr/Pr
COMPUTER IN 1
COMPUTER IN 2
MONITOR OUT
EXT. SP
CONTROL PORT 2
CONTROL PORT 1
AUDIO 2
(STEREO)
(STEREO)
AUDIO 1
(STEREO)
(8Ω)
AUDIO
VIDEO
S-VIDEO
(MONO)
R L
AV IN
COMPUTER
1
2
3
6 7
10
9
4
5
8
11
12
1 2 3 4
5 6
8 9
10 11
12
7
CONNECTING THE PROJECTOR
TERMINAL OF THE PROJECTOR
11
CONNECTING THE PROJECTOR
CONNECTING THE COMPUTER
Personal computers can be connected to the HDB15-pin (VGA) terminal on the projector.
Connect the computer to these terminals using the VGA cable and VGA/Macintosh adapter (provided). CAUTION: For projectors, the VGA cable provided is designed to reduce RFI (Radio Frequency Interference) emissions.
For regulatory compliance reasons, this cable must be used and must not be replaced by any other cable.
CONNECTING TO THE COMPUTER INPUT TERMINALS (1 and 2)
CONNECTING TO THE COMPUTER AUDIO INPUT JACKS (1 and 2)
CONNECTING TO THE CONTROL PORT (MINI DIN 8-PIN) CONNECTORS (1 and 2)
54321
109876
15 14 13 12 11
This terminal output the information of the selected computer source being viewed on the screen (Computer 1 or Computer 2). When video source is selected, this terminal outputs Computer 1 input information.
An external monitor can be connected to the HDB15-pin (VGA) terminal on the projector.
Connect the monitor to this terminal using the VGA cable (not provided).
Pin No./Signal
1 Red input 2 Green input 3 Blue input 4 Sense 2 5 Ground (Horiz.sync.) 6 Ground (Red) 7 Ground (Green) 8 Ground (Blue)
Pin No./Signal
9 Non Connect 10 Ground (Vert. sync.) 11 Sense 0 12 Sense 1 13 Horiz. sync 14 Vert. sync 15 Reserved
HDB 15-PIN TERMINAL
CONNECTING TO THE MONITOR OUTPUT TERMINAL
If you wish to control the computer with projector's remote control unit, you must connect control port (PS/2, Serial or ADB port) on your computer to projector's control port with cable. (three type cables supplied; for PS/2 Port, Serial Port and ADB Port).
Connect audio outputs from your computer to these jacks using the audio cable (not provided).
6
3
8
1
2
7
45
CONTROL PORT
––––––––
ADB
––––––––
GND
–––––––– –––––––– ––––––––
GND
RXD
–––––––– ––––––––
GND
RTS/CTS
TXD GND GND
–––––––-
CLK
DATA
GND
–––––––– ––––––––
GND
––––––––
Serial Port
ADB Port
1 2 3 4 5 6 7 8
PS/2 Port
NOTE: The RXD port (1 pin on the Serial Port) is provided on control port 2 connector only. If you control the projector by
computer, you must connect control port 2 connector.
12
CONNECTING THE PROJECTOR
Y Cb/Pb Cr/Pr
COMPUTER IN 1
COMPUTER IN 2
MONITOR OUT
EXT. SP
CONTROL PORT 2
CONTROL PORT 1
AUDIO 2
(STEREO)
(STEREO)
AUDIO 1
(STEREO)
(8Ω)
AUDIO
VIDEO
S-VIDEO
(MONO)
R L
AV IN COMPUTER
COMPUTER OUTPUT
COMPUTER
MONITOR CABLE (NOT PROVIDED)
SERIAL PORT INPUT
MONITOR OUTPUT
COMPUTER AUDIO INPUT 1 or 2
MOUSE CABLE FOR PS/2 PORT (PROVIDED)
MOUSE CABLE FOR SERIAL PORT (PROVIDED)
PS/2 PORT INPUT
VGA CABLE (PROVIDED)
AUDIO CABLE (NOT PROVIDED)
EXTERNAL AUDIO EQUIPMENT (Refer to page 18)
NOTE: When connecting the cable, the power cords of both the projector and the external equipment should be
disconnected from AC outlet. Turn the projector and peripheral equipment on before the computer is switched on.
COMPUTER INPUT 1 or 2
CONNECTING AN IBM-COMPATIBLE DESKTOP COMPUTER
AUDIO OUTPUT
CONTROL PORT OUTPUT 1 or 2
13
CONNECTING THE PROJECTOR
Y Cb/Pb Cr/Pr
COMPUTER IN 1
COMPUTER IN 2
MONITOR OUT
EXT. SP
CONTROL PORT 2
CONTROL PORT 1
AUDIO 2
(STEREO)
(STEREO)
AUDIO 1
(STEREO)
(8Ω)
AUDIO
VIDEO
S-VIDEO
(MONO)
R L
AV IN
COMPUTER
COMPUTER
SERIAL PORT INPUT
PS/2 PORT INPUT
AUDIO CABLE (NOT PROVIDED)
VGA CABLE (PROVIDED)
MOUSE CABLE FOR PS/2 PORT (PROVIDED)
MOUSE CABLE FOR SERIAL PORT (PROVIDED)
COMPUTER OUTPUT
CONTROL PORT OUTPUT 1 or 2
CONNECTING AN IBM-COMPATIBLE LAPTOP COMPUTER
NOTE: When connecting the cable, the power cords of both the projector and the external equipment should be
disconnected from AC outlet. Turn the projector and peripheral equipment on before the computer is switched on.
EXTERNAL AUDIO EQUIPMENT (Refer to page 18)
AUDIO OUTPUT
COMPUTER AUDIO INPUT 1 or 2
COMPUTER INPUT 1 or 2
123456
ON
Y Cb/Pb Cr/Pr
COMPUTER IN 1
COMPUTER IN 2
MONITOR OUT
EXT. SP
CONTROL PORT 2
CONTROL PORT 1
AUDIO 2
(STEREO)
(STEREO)
AUDIO 1
(STEREO)
(8Ω)
AUDIO
VIDEO
S-VIDEO
(MONO)
R L
AV IN
COMPUTER
14
CONNECTING THE PROJECTOR
COMPUTER
MONITOR CABLE (NOT PROVIDED)
COMPUTER OUTPUT
VGA/Macintosh ADAPTER (PROVIDED)
CONNECTING A MACINTOSH DESKTOP COMPUTER
ON
2
34
5
61
ON
OFF
VGA/Macintosh ADAPTER
SW1 ~ SW6
Set the dip switches as shown in the table below depending on the RESOLUTION MODE that you want to use before you turn on the projector and computer.
ADB PORT INPUT
SW1
ON OFF OFF
ON
RESOLUTION MODE 13" MODE (640
x
480)
16" MODE (832
x
624)
19" MODE (1024
x
768)
21" MODE (1152
x
870)
SW6
OFF OFF OFF OFF
SW5
OFF OFF OFF OFF
SW4
OFF
ON
OFF
ON
SW3 OFF OFF
ON ON
SW2
ON ON ON ON
NOTE: When connecting the cable, the power cords of both the projector and the external equipment should be
disconnected from AC outlet. Turn the projector and peripheral equipment on before the computer is switched on.
AUDIO OUTPUT
EXTERNAL AUDIO EQUIPMENT (Refer to page 18)
MOUSE CABLE FOR ADB PORT (PROVIDED)
AUDIO CABLE (NOT PROVIDED)
COMPUTER AUDIO INPUT 1 or 2
CONTROL PORT OUTPUT 1 or 2
COMPUTER INPUT 1 or 2
MONITOR OUTPUT
VGA CABLE (PROVIDED)
15
123456
ON
Y Cb/Pb Cr/Pr
COMPUTER IN 1
COMPUTER IN 2
MONITOR OUT
EXT. SP
CONTROL PORT 2
CONTROL PORT 1
AUDIO 2
(STEREO)
(STEREO)
AUDIO 1
(STEREO)
(8Ω)
AUDIO
VIDEO
S-VIDEO
(MONO)
R L
AV IN
COMPUTER
COMPUTER
AUDIO OUTPUT
ADB PORT INPUT
VGA/Macintosh ADAPTER (PROVIDED)
VGA CABLE (PROVIDED)
MOUSE CABLE FOR ADB PORT (PROVIDED)
COMPUTER INPUT 1 or 2
COMPUTER AUDIO INPUT 1 or 2
AUDIO CABLE (NOT PROVIDED)
CONNECTING A MACINTOSH POWERBOOK COMPUTER
CONNECTING THE PROJECTOR
NOTE: The Macintosh PowerBook requires the use of the PowerBook Video
Adapter shipped with the PowerBook.
ON
2
34
5
61
ON
OFF
VGA/Macintosh ADAPTER
SW1 ~ SW6
Set the dip switches as shown in the table below depending on the RESOLUTION MODE that you want to use before you turn on the projector and computer.
SW1
ON OFF OFF
ON
RESOLUTION MODE 13" MODE (640
x
480)
16" MODE (832
x
624)
19" MODE (1024
x
768)
21" MODE (1152
x
870)
SW6
OFF OFF OFF OFF
SW5
OFF OFF OFF OFF
SW4
OFF
ON
OFF
ON
SW3
OFF OFF
ON ON
SW2
ON ON ON ON
NOTE: When connecting the cable, the power cords of both the projector and the external equipment should be
disconnected from AC outlet. Turn the projector and peripheral equipment on before the computer is switched on.
CONTROL PORT OUTPUT 1 or 2
EXTERNAL AUDIO EQUIPMENT (Refer to page 18)
TO POWERBOOK VIDEO ADAPTER
16
CONNECTING THE VIDEO EQUIPMENT
CONNECTING THE PROJECTOR
Connect the S-VIDEO output from the video equipment to this jack using the S-video cable. The S-VIDEO jack has priority over the VIDEO (composite) jack.
CONNECTING TO THE VIDEO INPUT JACK
CONNECTING S-VIDEO INPUT JACK
Connect to the video and audio outputs of a VCR, video disc player, DVD player, video camera, satellite TV tuner or other AV equipment.
CONNECTING TO THE COMPONENT VIDEO INPUT JACKS
Connect the component video outputs (Y, Cb/Pb, Cr/Pr) from the DVD player or other video equipment to these jacks using the video cable. The COMPONENT VIDEO jack has priority over the S-VIDEO and VIDEO (composite) jacks.
Connect the video output from the video equipment to this jack using the video cable.
Connect the audio outputs from the video equipment to these jacks using the audio cable. When the audio output is monaural, connect it to the L (mono) jack.
CONNECTING TO THE AUDIO INPUT JACKS
17
Y Cb/Pb Cr/Pr
COMPUTER IN 1
COMPUTER IN 2
MONITOR OUT
EXT. SP
CONTROL PORT 2
CONTROL PORT 1
AUDIO 2
(STEREO)
(STEREO)
AUDIO 1
(STEREO)
(8Ω)
AUDIO
VIDEO
S-VIDEO
(MONO)
R L
AV IN
COMPUTER
VIDEO EQUIPMENT
Video Cassette Recorder
DVD Player Video Disc Player
Satellite TV Tuner
DVD Player
S-VIDEO OUTPUT
S-VIDEO INPUT
AUDIO INPUT
VCR Etc...
Video Camera
VIDEO OUTPUT
L R AUDIO OUTPUT
VIDEO INPUT
AUDIO INPUT
AUDIO OUTPUT
Y, Cb/Pb, Cr/Pr COMPONENT VIDEO OUTPUT
R L AUDIO OUTPUT
AUDIO INPUT
COMPONENT VIDEO INPUT
CONNECTING THE PROJECTOR
CONNECTING THE VIDEO EQUIPMENT
NOTE: When connecting the cable, the power cords of both the projector and the external equipment should be
disconnected from AC outlet. Turn the projector on before the peripheral equipment is switched on.
Loading...
+ 37 hidden pages