Canon FAU-S11 Service Manual
SERVICE
MANUAL
REVISION 0
APR. 2000
COPYRIGHT © 2000 CANON INC. CANON FAU-S11 REV.0 APR. 2000 PRINTED IN JAPAN (IMPRIME AU JAPON)
COPYRIGHT © 2000 CANON INC.
Printed in Japan
Imprimè au Japon
Use of this manual should be strictly supervised
to avoid disclosure of confidential information.
COPYRIGHT © 2000 CANON INC. CANON FAU-S11 REV.0 APR. 2000 PRINTED IN JAPAN (IMPRIME AU JAPON)
LIST OF SERIAL NUMBER
FAU-S11 F96-1911 AZH000000-
F96-1931 BZH000000-
COPYRIGHT © 2000 CANON INC. CANON FAU-S11 REV.0 APR. 2000 PRINTED IN JAPAN (IMPRIME AU JAPON)
CONTENTS
CHAPTER 1 : GENERAL DESCRIPTIONS
I. FEATURES ................................ 1-1
II. SPECIFICATIONS....................... 1-2
III. EXTERIOR FEATURES............... 1-3
CHAPTER 2 : OPERATION AND TIMING
I. BASIC OPERATION .................... 2-1
A. System Configuration.......... 2-1
CHAPTER 3 : MECHANICAL SYSTEM
I. PARTS REPLACEMENT .............. 3-1
A. Removing Top Cover ........... 3-1
B. Removing Hinge .................. 3-2
C. Removing FAU Cable ........... 3-7
A. Front View .......................... 1-3
B. Bottom View ....................... 1-3
B. Electrical System ................ 2-2
C. Inverter PCB ....................... 2-3
D. Removing Inverter Cover... 3-10
E. Attaching the Inverter Cover
......................................... 3-11
CHAPTER 4 : MAINTENANCE AND SERVICING
I. PERIODICAL REPLACEMENT
PARTS....................................... 4-1
II. CONSUMABLE PARTS
DURABILITY.............................. 4-1
CHAPTER 5 : TROUBLESHOOTING
I. POSSIBLE CAUSE AND CORRECTIVE
ACTION ..................................... 5-1
CHAPTER 6 : PARTS CATALOG
FIGURE 100 .............................. 6-2
III. PERIODICAL SERVICING ........... 4-1
IV. SPECIAL TOOLS ........................ 4-1
V. SOLVENTS AND LUBRICANTS .... 4-1
COPYRIGHT © 2000 CANON INC. CANON FAU-S11 REV.0 APR 2000 PRINTED IN JAPAN (IMPRIME AU JAPON)
APPENDIX
I. GENERAL CIRCUIT
DIAGRAM .................................. A-1
II. INVERTER PCB CIRCUIT DIAGRAM
........................................... A-2
COPYRIGHT © 2000 CANON INC. CANON FAU-S11 REV.0 APR 2000 PRINTED IN JAPAN (IMPRIME AU JAPON)
CHAPTER 1
GENERAL DESCRIPTIONS
I. FEATURES ................................ 1-1
II. SPECIFICATIONS....................... 1-2
III. EXTERIOR FEATURES............... 1-3
COPYRIGHT © 2000 CANON INC. CANON FAU S-11 REV.0 APR. 2000 PRINTED IN JAPAN (IMPRIME AU JAPON)
A. Front View .......................... 1-3
B. Bottom View ....................... 1-3
CHAPTER 1
I. FEATURES
FAU-S11 is a film adapter unit (FAU) used for CanoScan FB1210U to scan films incorporating
the following features.
* Color and monochrome, negative and positive films can be scanned.
* Film guide enables to scan 35mm film, brownie film (max. 120 x 60mm), and 4 x 5 inches
film.
COPYRIGHT © 2000 CANON INC. CANON FAU-S11 REV.0 APR. 2000 PRINTED IN JAPAN (IMPRIME AU JAPON)
1 - 1
CHAPTER 1
II. SPECIFICATIONS
Film Type : Color and monochrome, negative and positive
Film Size : 35mm sleeve (preview by 3 frames, scan by 1 frame)
35mm slide mount
Brownie (Max. 120 x 60mm)
4 x 5 inches
Light Source : Cold cathode fluorescent lamp
Brightness : 3200cd/square meters +/-10%
Operating Environment : Temperature : 10 to 35 degrees
Relataive humidity : 20 to 80%RH
Power Source : Supplied from CanoScan FB1210U
Standard point of scanning area : X=45mm, Y=35mm
Dimensions : 285 (width) x 407.5 (depth) x 33 (height) mm
Weight : 920g
Durability : 20,000 times of the FAU's open/close
Specifications are subject to change without prior notice.
1 - 2
COPYRIGHT © 2000 CANON INC. CANON FAU-S11 REV.0 APR. 2000 PRINTED IN JAPAN (IMPRIME AU JAPON)
III. EXTERIOR FEATURES
CHAPTER 1
A. Front View
q FAU Cable
w Top Cover
1
2
Figure 1-1
B. Bottom View
q Sponge Sheet
w Hinge
e Lamp Cover Assembly
1
2
3
Figure 1-2
COPYRIGHT © 2000 CANON INC. CANON FAU-S11 REV.0 APR. 2000 PRINTED IN JAPAN (IMPRIME AU JAPON)
1 - 3
CHAPTER 2
OPERATION AND TIMING
I. BASIC OPERATION .................... 2-1
A. System Configuration .......... 2-1
COPYRIGHT © 2000 CANON INC. CANON FAU S-11 REV.0 APR. 2000 PRINTED IN JAPAN (IMPRIME AU JAPON)
B. Electrical System ................ 2-2
C. Inverter PCB ....................... 2-3
CHAPTER 2
I. BASIC OPERATION
A. System Configuration
The film adapter unit FAU-S11 is an optional device for CanoScan FB1210U to provide the
light source for scanning films.
When the appropriate light source projects through a film and the host computer program
controls the scanning unit moving, charge-coupled-device (CCD) collects all the light signals of
the film and synchronically generates the real analog signals. The main PCB then converts the
analog signal into digital signal. Finally, scanner driver transforms the digital signal into an
image and saves it in the host computer.
Film Adapter Unit (FAU-S11)
Host
Computer
Inverter PCB
FAU Lamp
Figure 2-1
COPYRIGHT © 2000 CANON INC. CANON FAU-S11 REV.0 APR. 2000 PRINTED IN JAPAN (IMPRIME AU JAPON)
2 - 1
CHAPTER 2
B. Electrical System
Electrical control of the FAU is perfromed by the main PCB in the scanner. Inverter PCB
performs various processing in the FAU according to the control signal sent from the main
PCB.
CN2
FAU Lamp
Scanner
(Main PCB)
JP2
Inverter PCB
CN1
CN3
FAU Lamp
Figure 2-2
2 - 2
COPYRIGHT © 2000 CANON INC. CANON FAU S-11 REV.0 APR. 2000 PRINTED IN JAPAN (IMPRIME AU JAPON)
CHAPTER 2
C. Inverter PCB
FAU lamp ON depends on the device selection by the host computer. When the scanner is
powered ON, the scanning lamp is turned ON. When FAU is selected by the host computer as
a TWAIN or Plug-in Module compliant input device and application software is started, the FAU
lamp is turned ON and the scanning lamp is turned OFF.
FAU Lamp
CN2-2
FAU Lamp
CN2-3
CN3-2
CN3-3
Inverter PCB
CN1-1
-2
-3
Figure 2-3
JP2-1
Scanner
(Main PCB)
FLON
-2
+12V
-3
GND
COPYRIGHT © 2000 CANON INC. CANON FAU-S11 REV.0 APR. 2000 PRINTED IN JAPAN (IMPRIME AU JAPON)
2 - 3
Loading...