Canon 4K6021Z Users Manual
MULTIMEDIA PROJECTOR
User’s Manual
Safety Instructions
Before Use
Basic Guide
Projection Procedure
Convenient Projection
Features
Installation Procedure
Installation Guide
Connection Procedure
Adjusting the Image
Special Arrangements
Using Menus
Menu Guide
Menu Configuration
Menu Description
Maintenance
Product Specifications
Troubleshooting
ENG
How to Use This Manual
LENS button
FOCUS button
ZOOM button
Remote control
Projector
Symbols Used in This Manual
Sections labeled with these symbols give the following kinds of information.
Indicates precautions and information to note when using the projector.
Symbols of Button Operations
The projector can be operated using the buttons on the remote control or on the
side of the projector. The remote control allows you to operate all functions of the
projector.
In this document, the button’s operations are shown as below.
Remote control button
operation
Operation of buttons
on side of projector
Indicate the buttons to
be pressed
Thank you for purchasing a Canon projector.
The 4K6021Z Multimedia Projector is a high-performance laser projector
capable of projecting high-resolution computer screens and high-quality
digital images on a large screen.
This Manual
This is the user’s manual for 4K6021Z Multimedia Projector (hereafter, “projector”).
The “Basic Guide” describes basic steps before projection and introduces features
that are convenient in presentations and other situations. The “Installation Guide”
covers how to install the projector and join a network, and the “Menu Guide”
explains setting menus and how to use them.
Read this manual thoroughly to make the most of your projector. We recommend
requesting installation by a qualified technician or the Canon Customer Support
Center.
Focusing / Resizing the Image
Press the ZOOM button on the remote control to adjust the image size, and press
the FOCUS button to adjust the focus. You can also press the LENS button on the
projector once to adjust focus and twice to adjust image size.
2
4K6021Z/4K6020Z/4K5020Z/WUX7000Z/WUX6600Z/
WUX5800Z/WUX7500/WUX6700/WUX5800
Notification of an Addition to Functions with a Firmware
Upgrade
4K6021Z (Ver. 01.010100)
4K6020Z/4K5020Z (Ver. 01.040300)
WUX7000Z/WUX6600Z/WUX5800Z (Ver. 01.040400)
WUX7500/WUX6700/WUX5800 (Ver. 01.040200)
■ Addition of a Dynamic Contrast Function (4K6021Z/4K6020Z/
4K5020Z/WUX7000Z/WUX6600Z/WUX5800Z only)
Refer to “Contrast detail adjustment” in this manual.
■ Addition of a Set Value Copy Function (Common to All Models)
You can copy the set values of a projector to other projectors from a computer
via a network by connecting this device to wired LAN or wireless LAN.
You cannot copy the following settings.
• [Input settings] Tab
Input level / Color space / Progressive / PC-free multi projection / Split screen
• [Image adjustment] Tab
Image Priority / Image Mode (*1)
• [Install settings] Tab
Zoom / Keystone / Digital image shift / Professional Settings → RGB alignment,
Lens shift mode, Marginal Focus and Edge Blending / Lens position
• [System settings] Tab
User screen settings → User logo / On screen → Menu position / Remote control
channel / Other settings
• [Network settings] Tab
Items Other Than PJLink, AMX Device Discovery and Crestron RoomView
• [Information] Tab Contents
• Other
Zoom, Focus, Lens shift, Input, Digital zoom, Mute and Freeze
Steps to Copy Set Values
1
Connect the computer and projectors to wired LAN or wireless LAN (*2)
(*3).
2
Startup the web browser. Input “http://(IP address of the projector for
reading)/professional/read” and then press the [Enter] key.
3
Input the login username and password on the web screen (*4).
The READ screen will be displayed.
4
Press the [Start read] button.
5
Press the [OK] button once the reading has been completed.
The read file will be saved in the download folder.
6
Input “http://(IP address of the projector for writing)/professional/write” in
the address of the web browser and then press the [Enter] key.
Input the login username and password on the web screen in the same way as
with step 3.
The WRITE screen will be displayed.
7
Press the [Browse] button. Select the set value file you saved in step 5
and then press the [Start write] button.
8
Press the [OK] button once the writing has been completed.
* If you wish to copy set values to multiple projectors, repeat steps 6 to 8.
(*1) If the user memory has already been created at the copy source, that content will be
reflected in the copy destination. If it has not already been created at the copy source, the
user memory at the copy destination will be retained.
(*2) Refer to “Network settings” in this manual for details.
(*3) Operating conditions:
• The projector should be in the projection or standby state (4K6021Z/4K6020Z/4K5020Z/
WUX7000Z/WUX6600Z/WUX5800Z)
• The projector should be in the projection state (WUX7500/WUX6700/WUX5800)
• The wired or wireless network function should be on
(*4) Refer to “Password settings” in this manual for details.
Communications may fail due to a timeout if the standby power settings of the
projector are in “Low-power” depending on the browser specifications.
In that case, reload the page and re-read/write.
Table of Contents
How to Use This Manual............... 2
Projector Highlights...................... 4
Safety Instructions........................ 6
Safety Symbols in this Manual ........... 12
Precautions for Use ............................. 13
Power Supply ....................................... 13
Installation and Use ............................. 15
Laser Light Source .............................. 16
Remote Control Batteries.................... 17
Handling................................................ 17
For Safe Use ................................ 19
Carrying and Installation..................... 19
Before Installation....................... 21
Precautions When Carrying /
Shipping the Projector ........................ 21
Precautions for Installation................. 21
Open Source Software ............... 26
Before Use ................................... 27
Included Accessories .......................... 27
Projector Part Names and
Functions.............................................. 28
Remote Control .................................... 33
Basic Guide ............................38
Projection Procedure.................. 39
Step 1 Connect Other Equipment....... 40
Step 2 Turn the Projector On .............. 41
Step 3 Select an Input Signal.............. 42
Step 4 Adjust the Image ...................... 43
Step 5 Select the Image Quality
(Image Mode)........................................ 44
Turn the Projector Off.......................... 46
Convenient Projection
Features ....................................... 47
Convenient Features ........................... 47
Installation Guide...................50
Installation Procedure ................ 51
Relationship Between Projecting
Distance and Image Size ..................... 51
Installing / Removing the Lens Unit ... 53
Installation ............................................ 56
Connection Procedure................62
Connecting Other Equipment............. 62
Connecting to a Network..................... 65
Controlling the Projector from a
Computer .............................................. 79
Adjusting the Image ....................81
Filling the Screen ................................. 81
Adjusting Keystone Distortion ........... 81
Advanced Registration to Adjust
Projected Images ................................. 85
Adjusting Projected Images
with Partial Distortion Correction....... 89
Adjustment Using a Test Pattern ....... 92
Special Arrangements ................93
Adjusting Peripheral Focus ................ 93
Projecting from Multiple Projectors at
Once (Edge Blending) ......................... 96
Menu Guide ..........................101
Using Menus ..............................102
Menu Configuration ..................105
Menu Description ......................113
Input settings ..................................... 113
Image adjustment .............................. 117
Install settings.................................... 127
System settings ................................. 139
Network settings ................................ 158
Checking Projector Information ....... 173
Projector Web Screen Menu.....174
Maintenance /
Product Specifications /
Troubleshooting ..................190
Maintenance...............................191
Cleaning the Projector....................... 191
Replacing the Air Filter...................... 191
Product Specifications .............193
Troubleshooting........................205
LED Indicator Details......................... 205
Symptoms and Solutions.................. 206
Index...........................................211
Option.........................................213
3
Projector Highlights
Bright Yet Compact, With a Laser Light Source
A bright projector that is also compact, at 480 x 545 x 196 mm (18.9 x 21.5 x 7.7 in.,
W x D x H). Features a laser light source that lasts longer than traditional mercury
lamps.
Peripheral Focus Adjustment
Image focus can be adjusted on the edges of the screen, enabling use in dome
projection.
HDBaseT Input
The projector supports HDBaseT, a next-generation connectivity standard.
HDBaseT offers a convenient connection for carrying high-quality video and audio
signals equivalent to HDMI across distances up to 70 m (229.7')* over a single LAN
cable.
* Maximum distance for 2K signals: 100 m (328.1')
Lens Shift
Lens shift enables motorized image repositioning up, down, left, or right for greater
freedom in installation.
Motorized Zoom and Focus Adjustment
Efficient setup using motorized zoom and focus adjustment.
Full Range of Lens Units Available
Choose the optimal lens unit for the projection distance or purpose.
Superior Video Viewing Experience
Refinements in motion blur reduction make video projection more enjoyable to
watch.
Scheduling
Automate projector tasks according to your schedules. Turn the projector on or off,
switch input signals, and more.
Edge Blending
Blend the overlapping edges of images from multiple projectors to make the overall
image more seamless.
4
Projector Highlights
Wi-Fi Connectivity
In addition to wired LAN connectivity, the projector also supports Wi-Fi.
In Projector Access Point (PJ AP) mode, the projector can be connected to up to
five computers without using a wireless access point.
Canon Service Tool for PJ (Canon ST)
An iOS app for easy remote control and status management of projectors over
Wi-Fi. Connect to a projector used as an access point (P66), or connect via an
existing access point (P66). Note that a password is required when using Canon
ST (P174).
DisplayPort
The DisplayPort interface supports 4K_60P_10bit_4:4:4 video signals*, making
possible more realistic images and smoother gradients.
* When two DisplayPort 1.2 ports are used together.
5
Safety Instructions
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Before installing and operating the projector, read this manual thoroughly.
This projector provides many convenient features and functions. Operating the
projector properly enables you to manage those features and maintain it in good
condition for many years to come.
Improper operation may result in not only shortening the product life, but also
malfunctions, fire hazards, or other accidents.
If your projector does not seem to be operating properly, read this manual again,
check operations and cable connections, and try the solutions in the
“Troubleshooting” section in the back of this manual. If the problem still persists,
contact the Canon Customer Support Center.
THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE
CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT
WITHIN THIS UNIT.
THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT
OPERATING AND MAINTENANCE INSTRUCTIONS FOR THIS
UNIT IN THE OWNER’S MANUAL.
CAUTION
Not for use in a computer room as defined in the Standard for the Protection of
Electronic Computer / Data Processing Equipment, ANSI / NFPA 75.
6
Safety Instructions
Safety Precautions
WARNING:
• THIS APPARATUS MUST BE GROUNDED.
• TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
• This projector produces intense light from the projection lens. Do not stare
directly into the lens, otherwise eye damage could result. Be especially careful
that children do not stare directly into the beam.
• Install the projector in a proper position. Otherwise it may result in a fire hazard.
• Do not cover the ventilation slots on the projector. Heat build-up can reduce the
service life of your projector, and can also be dangerous.
• If the projector is unused for an extended time, unplug the projector from the
power outlet.
• Do not project the same image for a long time.
An afterimage may remain on the LCD panels due to the characteristics of the
panels of the projector.
Safety Instructions
CAUTION ON HANGING FROM THE
CEILING
When hanging the projector from the ceiling, clean the air intake vents and top of
the projector periodically with a vacuum cleaner. If you leave the projector unclean
for a long time, the cooling fans can be clogged with dust, and it may cause a
breakdown or a disaster.
DO NOT SET THE PROJECTOR IN GREASY, WET, OR SMOKY CONDITIONS
SUCH AS IN A KITCHEN TO PREVENT A BREAKDOWN OR A DISASTER. IF
THE PROJECTOR COMES IN CONTACT WITH OIL OR CHEMICALS, IT MAY
BECOME DETERIORATED.
7
Safety Instructions
■ READ AND KEEP THIS OWNER’S MANUAL FOR LATER
USE.
All the safety and operating instructions should be read before beginning to operate
the product.
Read all of the instructions given here and retain them for later use. Unplug this
projector from the AC power supply before cleaning. Do not use liquid or aerosol
cleaners on the projector. Use a damp cloth for cleaning.
Follow all warnings and instructions marked on the projector.
For added protection of the projector during a lightning storm, or when it is left
unattended or unused for long periods of time, unplug it from the wall outlet. This
will prevent damage due to lightning and power surges.
Do not expose this unit to rain or use near water... for example, in a wet basement,
near a swimming pool, etc...
Do not use attachments not recommended by the manufacturer as they may result
in hazards.
Do not place this projector on an unstable cart, stand, or table. The projector may
fall, causing serious injury to a child or adult, and serious damage to the projector.
Use only with a cart or stand recommended by the manufacturer, or sold with the
projector. Wall or shelf mounting should be carried out in accordance with the
manufacturer’s directions, and should use a mounting kit approved by the
manufacturers.
An appliance and cart combination should be moved with care.
Sudden stops, excessive force, and uneven surfaces may cause
the appliance and cart combination to overturn.
Slots and openings in the rear and front of the cabinet are provided
for ventilation, to insure reliable operation of the equipment and to protect it from
overheating.
The openings should never be covered with cloth or other materials, and the
bottom opening should not be blocked by placing the projector on a bed, sofa, rug,
or other similar surface. This projector should never be placed near or over a
radiator or heat register.
This projector should not be placed in a built-in installation such as a book case
unless proper ventilation is provided.
8
Safety Instructions
Never push objects of any kind into this projector through cabinet slots as they may
touch dangerous voltage points or short out parts that could result in a fire or
electric shock. Never spill liquid of any kind onto the projector.
Do not install the projector near the ventilation duct of air-conditioning equipment.
This projector should be operated using only the type of power source indicated on
the marking label. If you are not sure of the type of power supplied, contact the
Canon Customer Support Center or local power company.
Do not overload wall outlets and extension cords as this can result in fire or electric
shock. Do not allow anything to rest on the power cord. Do not locate this projector
where the cord may be damaged by people walking on it.
Do not attempt to service this projector yourself as opening or removing covers
may expose you to dangerous voltages or other hazards. Refer all servicing to
qualified service personnel.
Unplug this projector from the wall outlet and refer servicing to qualified service
personnel under the following conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the projector.
c. If the projector has been exposed to rain or water.
d. If the projector does not operate normally after following the operating
instructions. Adjust only those controls that are covered in the operating
instructions as improper adjustment of other controls may result in damage and
will often require extensive work by a qualified technician to restore the projector
to normal operating condition.
e. If the projector has been dropped or the cabinet has been damaged.
f. When the projector exhibits a distinct change in performance-this indicates a
need for servicing.
Safety Instructions
When replacement parts are required, be sure the service technician uses
replacement parts specified by the manufacturer that have the same characteristics
as the original parts. Unauthorized substitutions may result in fire, electric shock, or
injury.
Upon completion of any service or repairs to this projector, ask the service
technician to perform routine safety checks to determine that the projector is in safe
operating condition.
9
Safety Instructions
Ground
AC Power Cord Requirement
The AC Power Cord supplied with this projector meets the requirements for use in
the country you purchased it.
AC Power Cord for the United States and Canada:
The AC Power Cord used in the United States and Canada is
listed by the Underwriters Laboratories (UL) and certified by
the Canadian Standard Association (CSA).
The AC Power Cord has a grounding-type AC line plug. This is
a safety feature to ensure the plug fits into the power outlet. Do
not try to tamper with this safety feature. Should you be unable
to insert the plug into the outlet, contact your electrician.
THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND
EASILY ACCESSIBLE.
10
Safety Instructions
Only for European Union and EEA (Norway, Iceland and
Liechtenstein)
These symbols indicate that this product is not to be disposed of
with your household waste, according to the WEEE Directive (2012/
19/EU), the Battery Directive (2006/66/EC) and/or national
legislation implementing those Directives.
If a chemical symbol is printed beneath the symbol shown above, in
accordance with the Battery Directive, this indicates that a heavy
metal (Hg = Mercury, Cd = Cadmium, Pb = Lead) is present in this
battery or accumulator at a concentration above an applicable
threshold specified in the Battery Directive.
This product should be handed over to a designated collection point,
e.g., on an authorized one-for-one basis when you buy a new similar
product or to an authorized collection site for recycling waste
electrical and electronic equipment (EEE) and batteries and
accumulators. Improper handling of this type of waste could have a
possible impact on the environment and human health due to
potentially hazardous substances that are generally associated with
EEE. Your cooperation in the correct disposal of this product will
contribute to the effective usage of natural resources.
For more information about the recycling of this product, please
contact your local city office, waste authority, approved scheme or
your household waste disposal service or visit
www.canon-europe.com/weee
, or www.canon-europe.com/battery.
Safety Instructions
11
Safety Instructions
Safety Symbols in this Manual
This section describes the safety symbols used in this manual. Important projector
safety information is identified by the following symbols. Always observe the safety
information by these symbols.
Denotes the risk of death or serious injury from improper
handling if the information is not observed. To ensure safe use,
always observe this information.
Denotes the risk of injury from improper handling if the
information is not observed. To ensure safe use, always observe
this information.
Denotes the risk of electric shock from improper handling if the
information is not observed. To ensure safe use, always observe
this information.
Denotes the risk of burns from improper handling if the
information is not observed. To ensure safe use, always observe
this information.
Denotes prohibited actions.
Denotes required actions or information that must be observed.
12
Safety Instructions
Precautions for Use
As this section contains important safety-related information, be sure to read the
following carefully beforehand in order to use your projector correctly and safely.
Power Supply
During installation, keep the projector plug easily accessible so that the projector can be
unplugged immediately if necessary, or keep a circuit breaker within reach.
If the following situations occur, turn the power off, remove the power plug from the
power outlet and contact the Canon Customer Support Center. Failure to do so could
cause a fire or result in an electric shock.
• If smoke is emitted
• If an unusual smell or noise is emitted
• If water or other liquid has entered the projector
• If metal or any other foreign material has entered the projector
• If the projector is knocked over or dropped and the cabinet is
damaged
Pay attention to the following points regarding the power source, power plug and
handling of the connector. Failure to do so may cause a fire or electric shock.
Safety Instructions
• Do not place any objects on the power cord and do not allow it to
become trapped under the projector.
• Do not cover the power cord with a carpet.
• Do not modify or excessively bend, twist, pull, wind, or bundle the
power cord.
• Keep the power cord away from heaters and other sources of
heat.
• Do not use a damaged power cord. If the power cord is
damaged, contact the Canon Customer Support Center.
•
Do not use any power source with a voltage other than the voltage
indicated (AC 100 – 240 V).
• Do not insert any metal objects into the contact parts of the
power plug or connector.
• The power cord included with this projector is for use exclusively
with this product. Do not use this cord for other products.
• Do not remove the power plug or connector with wet hands.
13
Safety Instructions
Pay attention to the following points regarding the power source, power plug and
handling of the connector. Failure to do so may cause a fire or electric shock.
• Insert the power plug and connector securely up to the base.
Additionally, do not use a damaged power plug or an outlet that is
loose.
• Do not pull the power cord and be sure to hold the power plug or
connector when removing. Incorrect handling may damage the
power cord.
• When using an extension cord, do not exceed the cord’s rated
capacity.
• Do not exceed the rated capacity of the outlet (as by using it for
more than one piece of equipment), which poses a risk of fire
from overheating.
• Periodically inspect the power plug and outlet and remove any
dust or dirt from between the plug and the outlet.
• Do not touch the projector itself, the power cord, or the cable if
lightening strikes.
• Do not move the projector until you have switched off the power,
removed the power plug from the power outlet and unplugged
any other cables.
• Unplug the projector before cleaning or maintenance.
• Before you install or remove the lens unit, be sure to unplug the
power plug of the projector from the power outlet.
14
Safety Instructions
Installation and Use
Pay attention to the following points regarding installation and handling of the projector.
Failure to do so may cause a fire, electric shock or personal injury.
• Do not use the projector where it might get wet, such as outdoors
or by bathtubs or showers.
• Do not place containers containing a liquid on top of the
projector.
• Do not install the projector in a location that is damp or dusty, or
where there is a lot of oily smoke or steam. Oil can degrade the
plastic, which could result in a ceiling-mounted projector falling
from its mounting.
• Make sure to implement anti-fall measures such as an anti-fall
wire when installing the projector in high places, for example,
installing it on the ceiling.
• Do not remove the cabinet from the projector or disassemble it.
The interior of the projector contains high-voltage components as
well as parts that are hot. If inspection, maintenance or repair is
required, contact the Canon Customer Support Center.
• Do not disassemble or modify the projector (including
consumable parts) or the remote control.
• Do not look directly into the exhaust vents during use.
• Do not insert any object into vents in the projector, such as the air
intake vent or exhaust vents.
• Do not place a pressurized can in front of the exhaust vents. The
pressure of the contents of the can may increase due to heat
from the exhaust vents and this could result in an explosion.
• When cleaning off dust or dirt from projector parts such as the
lens or filter, never use any spray that is flammable. Internal parts
that become hot may ignite and cause a fire.
• Do not use adhesives, lubricants, oils, or alkaline detergents for
maintenance of the projector. They could adhere to the cabinet
and damage it, possibly resulting in the projector falling from its
mounting and causing an accident or personal injury.
• As strong light beams are emitted
while the projector is in use, do
not look directly into the projector
lens. Doing so could cause an
eye injury. Pay particular attention to prevent small children from
doing so.
• Operators shall control access to the beam within the hazard
distance or install the product at a height that will prevent eye
exposure within the hazard distance.
Safety Instructions
15
Safety Instructions
Pay attention to the following points regarding installation and handling of the projector.
Failure to do so may cause a fire, electric shock or personal injury.
• Do not hold or install optical instruments (such as magnifying
glasses, reflectors, or glasses) in the path of light from the
projector. If projected light is refracted or reflected and enters
people’s eyes, it may result in eye injury.
• If children may approach the projector or touch it, always ensure
the projector is used under adult supervision.
• No direct exposure to the beam shall be permitted.
• Do not lift the projector alone. Have at least one assistant.
• When setting the projector on a high surface for projection, be
sure the surface is flat and stable.
• Do not use the projector on a soft surface such as carpet or
sponge mat, etc.
• For ceiling mounting or other installation work, request service
from a qualified technician or the Canon Customer Support
Center. Poor installation work could result in an accident.
• To avoid hazards such as parts falling when the lens of a ceilingmounted projector is replaced, request service from a qualified
technician or the Canon Customer Support Center.
• Do not use where combustible or explosive gases may occur.
Internal parts that become hot may ignite and cause a fire.
Laser Light Source
• The projector incorporates a laser module. Disassembly or
modification is dangerous and must not be attempted.
• Operate and adjust the projector only as described in this
manual. Incorrect operation or adjustment poses a risk of
exposure to potentially hazardous laser light.
• Do not use when damaged. Even if the projector is used as
described in this manual, failure to discontinue use when it is
damaged (as indicated by screen abnormalities) may result in
fire, electric shock, or eye injury from laser light.
• For assistance when disposing of the projector, contact the
Canon Customer Support Center. Do not disassemble the
projector yourself when disposing of it.
16
Safety Instructions
Remote Control Batteries
Pay attention to the following points regarding handling of batteries. Failing to do so
could result in a fire or personal injury.
• Do not heat, short circuit or disassemble the batteries, or place
them in a fire.
• Do not attempt to recharge the batteries that are included with
the remote control.
• Remove the batteries when they are flat or when the remote
control will not be used for a long period of time.
• When replacing the batteries, replace both at the same time.
Also, do not use two batteries of a different type at the same
time.
• Insert the batteries with the + and – terminals in the correct
directions.
• If any liquid from inside the batteries leaks out and contacts your
skin, be sure to wash the liquid off thoroughly.
Safety Instructions
Handling
Pay attention to the following points regarding installation and handling of the projector.
• If the projector will not be used for a long period of time, be sure
to remove the power plug from the power outlet to ensure safety.
Failure to do so presents a risk of fire if dust accumulates on the
plug or outlet.
• Do not plug headphones or earphones into the AUDIO OUT
terminal. Doing so may cause hearing impairment.
• Do not set the volume too high initially. Doing so may cause
hearing impairment from sudden sounds played at high volume.
Lower the volume before turning off the projector, and after
startup, raise it gradually.
• Do not touch parts of the cabinet around and above the exhaust
vents, which may become hot during projection. Pay particular
attention in preventing young children from touching these parts.
Additionally, do not place any metal objects around or above the
exhaust vents. Such objects may become hot from the projector,
which may result in burns or other injury.
17
Safety Instructions
Pay attention to the following points regarding installation and handling of the projector.
• Do not place any heavy objects on top of the projector or sit/
stand on it. Pay particular attention to prevent small children from
doing so. The projector may be knocked over and this could
result in damage or a personal injury.
• Do not place the projector on an unstable or slanted surface.
Doing so may cause the projector to fall or be knocked over and
could result in a personal injury.
• Do not place any objects in front of the lens
during projection. Doing so could cause a fire.
• The projector is provided with a lens shift
function to move the lens up, down, left, and
right using the motor. Do not touch the lens while it is moving.
Touching the lens when it is moving may result in personal injury.
• Before replacing the lens unit, wait at least 30 minutes after the
projector is turned off to allow the lens unit to cool down. Failure
to do so may result in burns or injury.
18
For Safe Use
Carrying and Installation
Pay attention to the following points when carrying or transporting the projector.
• If transportation is necessary, the lens unit should be removed before
transporting the projector. If the projector is subjected to excessive impacts
during transportation, the lens unit or projector may be damaged.
• This projector is a precision instrument. Do not knock it over or subject it to
impacts. Doing so may cause a malfunction.
• Retract the adjustable feet before moving the projector. Leaving the feet
extended may cause damage.
• When carrying or holding up the projector after attaching the lens unit, be
sure not to hold the lens. Doing so may cause damage to the lens unit or
projector.
• Do not touch the lens with bare hands. Any smudges or fingerprints on the
lens may affect image quality.
• Protection of the projector cannot be guaranteed if used packaging or shockabsorbent materials are reused. Fragments from shock-absorbent material
may also enter the interior of the projector which could cause a malfunction.
For Safe Use
19
For Safe Use
At least
50 cm (1.6')
At least
2cm (0.8")
At least
50 cm (1.6')
At least
50 cm (1.6')
Pay attention to the following points when installing or using the projector.
• Be careful of condensation.
If the projector is abruptly taken to a warmer location, or if the room
temperature rises abruptly, moisture in the air may condense on the lens or
mirror and affect projected images. In this case, wait a while and make sure
the moisture has evaporated before resuming use.
• Do not install the projector in a location where the temperature is high or low.
Doing so may cause a malfunction. Ranges for the environment of use and
storage are as follows.
• Environment of use: 0°C (32°F) to 45°C (113°F), 20% to 85% RH
• Storage temperature: -20°C (-4°F) to 60°C (140°F)
• When using the projector at altitudes above 2,300 m (7,545.8'):
Adjust projector installation settings from the menu (P133).
• Install the projector leaving at least 50 cm (1.6') between air intake/exhaust
vents and walls on each side of the projector. Leave a gap of at least 2 cm
(0.8") from the bottom of the projector. There is an air intake underneath the
projector. Failure to leave enough space may trap heat inside the projector
and damage it.
• Do not place any objects on top of the projector that may change shape or
color due to heat.
• Do not install the projector near high-voltage electrical power lines or an
electrical power source. This may cause malfunction.
• Afterimages may occur when the image changes after the same image has
been projected for some time. This is due to the nature of the LCD panels
and does not indicate a problem. The afterimage will dissipate after a while
during normal projection.
20
Before Installation
Precautions When Carrying / Shipping the Projector
Prepare the projector as described below before carrying it.
• Disconnect the cables connected to the projector. Carrying the
projector with the cables attached may cause an accident.
• Retract the adjustable feet before moving the projector. Leaving
the feet extended may cause damage.
• Do not subject the projector to strong impacts or vibrations.
Precautions for Installation
Be sure to read “Safety Instructions” and “For Safe Use” (P6 – P19). Also
take the following precautions during installation.
• Do not strike the projector or subject it to impact. Doing so may
cause a malfunction.
• Do not install the projector standing on one side or in other
unsteady positions. The projector may be damaged if it tips
over.
Before Installation
■ Do Not Use in the Following Environments
• Locations with excessive humidity, dust, oily smoke or tobacco
smoke
Adhesion to the lens, mirrors or other optical parts may reduce image
quality. In addition, oil can degrade the plastic, which could result in a
ceiling-mounted projector falling from its mounting.
• Near high-voltage power lines or sources of electrical power
This may cause malfunction.
• On soft surfaces such as carpets or cushioned mats
This may cause a fire or damage the projector.
• Locations with excessive temperature or humidity
• Locations subject to vibration or impact
• Near heat or smoke detectors
• Near the ocean, or near air conditioner vents
• Locations where corrosive gases occur, such as sulfur gas from
hot springs
This may damage the projector. Acceptable ranges for operating and
storage temperature and humidity are as follows.
* Operating temperature and humidity applies to when the projector
is projecting or in standby mode.
Operating temperature Operating humidity Storage temperature
0°C (32°F) – 45°C (113°F)
20%
–
85%
-20°C (-4°F) – 60°C (140°F)
21
Before Installation
Exhaust vent
Air intake vent
Warmed
airflow
Air intake vent
■ Do Not Touch the Lens with Bare Hands
Do not touch the lens with bare hands. Any smudges or
fingerprints on the lens may affect image quality.
■ Allow a 30 Min. Warm Up before Focus Adjustment (P43),
if Possible
Immediately after startup, the heat of the light source may prevent stable focus.
When adjusting focus, it is also helpful to use the test pattern (10) (P92, P138).
■ Install at a Sufficient Distance from Walls and Other Obstructions
If the air intake or exhaust
vent is blocked, heat will
accumulate inside the
projector, possibly resulting
in a shortened projector
lifetime or a malfunction.
Similarly, do not install in
narrow, enclosed spaces
with poor ventilation. Install
in a well-ventilated location.
Ensure a minimum
clearance of 50 cm (1.6') on
both sides, and behind the projector. Also ensure a minimum
clearance of 2 cm (0.8") below the projector.
■ Be Careful of Condensation
If the temperature of the room rises suddenly, moisture in the air may condense on
the projector lens and mirror, causing the image to become blurred. Wait until the
condensation has evaporated for the image projected to return to normal.
■ At Altitudes above 2,300 m (7,545.8'), Adjust the Settings
Projector settings must be adjusted when using the projector at altitudes of 2,300 m
(7,545.8') or higher. Specifically, refer to instructions for [High altitude] (P133) in the
[Install settings] menu.
22
Before Installation
■ When Using Mounted on the Ceiling
When the projector is used mounted on
the ceiling or installed in a high
location, it is necessary to periodically
clean the air intake and exhaust vents,
and the area around the air filter. Dust
that accumulates in intake or exhaust
vents may impair ventilation, raising the
temperature inside and posing a risk of
damage or fire. Use a vacuum cleaner
or similar means to remove dust from
the intake vent and exhaust vent.
■ Install Facing in the Correct Direction
• Projection is possible upward, downward, or in a variety of
directions, but do not block the air intake and exhaust vents. In
particular, always ensure a minimum clearance of 2 cm (0.8")
from the air intake vent on the bottom of the projector.
• There are no options for installing the projector other than the
ceiling attachment.
Before Installation
23
Before Installation
■ Precautions for Portrait (Upright) Installation
• Do not block the air intake or exhaust vents. In particular,
because there is an air intake vent on the bottom, always ensure
a minimum clearance of 2 cm (0.8") from the bottom.
• Note that no mounting brackets or similar accessories for
portrait installation are available.
■ Light Source
The projector uses laser as a light source. The laser has the following
characteristic.
Factors such as long-term use and environmental changes may
affect image quality. You can counteract changes in brightness
from hours of use or the ambient temperature by performing
[Light source calibration] in [Calibration] (P156).
24
Before Installation
Copyright Notice
Please note that enlarging or reducing the size of an image for commercial
purposes or public presentation may infringe on the legally protected copyright
or the copyright holder of the original material.
Ensure Network Security
Take measures to ensure network security. Note that Canon is not liable in any
way for direct or indirect loss from network security incidents, such as
unauthorized access.
Before use, configure projector, computer, and network security settings
appropriately.
• Set up the projector for connections only within your protected network,
behind a firewall or the like, instead of direct Internet connections.
• When using the projector in a wireless network, also configure the Wi-Fi
security settings.
• Change the Wi-Fi security key on a regular basis.
About Trademarks
• Ethernet is a registered trademark of Xerox Corporation.
• Microsoft and Windows are registered trademarks or trademarks of Microsoft
Corporation in the United States and/or other countries.
• Mac, Mac OS and Macintosh are trademarks of Apple Inc., registered in the
United States and/or other countries.
• HDMI, the HDMI logo and High-Definition Multimedia Interface are
trademarks or registered trademarks of HDMI Licensing, LLC.
• PJLink is a registered trademark of JBMIA and pending trademark in some
countries.
• PJLink is a registered trademark, or an application has been submitted for
trademark, in Japan, the United States and/or other countries or regions.
• AMX is a registered trademark of Harman International Industries, Inc.
• Crestron®, Crestron RoomView®, and Crestron Connected™ are registered
trademarks of Crestron Electronics, Inc.
• Extron and XTP are trademarks or registered trademarks of RGB Systems,
Inc. in the United States and/or other countries.
• HDBaseT™ and the HDBaseT Alliance logo are trademarks of the HDBaseT
Alliance.
• Wi-Fi is a registered trademark of the Wi-Fi Alliance.
• Wi-Fi CERTIFIED, WPA, WPA2, and the Wi-Fi CERTIFIED logo are used in
reference to methods of configuration developed by the Wi-Fi Alliance.
• All other trademarks are the property of their respective owners.
Before Installation
25
Open Source Software
Part of this product includes software licensed under the GNU General Public
License (GPL)
(1) Please access <https://global.canon/en/oss/scd/index.html> to fill the request
form so that you receive an e-mail with the URL to download the source code;
or
(2) Please send us a letter in writing with the following information, so that you
receive the source code via postal mail.
In case you have chosen this (2), WE MAY CHARGE YOU no more than the
cost of performing this distribution.
(i) Your Address (Country/Region, ZIP code, Address, Your name)
[mandatory]
(ii) Your e-mail address (for the purpose of possible communication with us)
[optional]
(iii) Product Name / Application Name [mandatory]
(iv) Version [mandatory]
Please check “Firmware” in the “Information” menu.
- Addressee:
Open Source Promotion Division, Canon Inc.
30-2, Shimomaruko 3-chome, Ohta-ku,Tokyo 146-8501, Japan
- Please see Privacy Notice at Canon Global <https://global.canon/>.
26
Before Use
• Remote control • Batteries for the remote control
(AAA size x2)
(part no.: RS-RC07)
• Important Information
• Warranty Card
• Power cord
(1.8 m / 5.9')
For Continental
Europe
For the U.S.A.
and Canada
Included Accessories
Before use, make sure the following items are included in the package.
Before Use
27
Before Use
(7) (5)
(3)
(4)
(1)
(2)
(6)
(8)
Do not block the air
intake. Doing so may
cause a malfunction.
(9)
(11)
(10)
(4)
Do not block the air
exhaust. Doing so may
cause a malfunction.
(12)
(4)
(13)
Projector Part Names and Functions
■ Front Side
(1) Power cord connector (P64)
(2) Infrared remote receiver
(P36)
(3) Lens unit (sold separately)
(4) Air intake vent
(5) Side control (P29)
(6) Terminals and connectors
(P32)
(7) Anti-theft lock hole
An anti-theft wire cable (not
included) can be connected.
(8) LED indicators (P30)
■ Rear Side
■ Bottom Side
(9) Exhaust vent
(10) Infrared remote receiver
(P36)
(11) Air filter frame (P191)
(12) Adjustable feet (P60)
(13) Security bar
28
Loading...