Cannon CANTERBURY INBUILT User Manual

MAKER’S WARRANTY
Cannon
INBUILT MODELS
CANTIB, CANTIBLP
CANTIBM, CANTIBMLP
USER INSTRUCTIONS
INSTALLATION INSTRUCTIONS
This heater is approved for use with Natural and Propane gases.
Please leave instructions with the owner
Contents
Contents 2
Warranty 3
Safety warnings 4-5
What to do if you smell gasWarningsStandards
User instructions 6-8
Operating instructionsCleaning
Heater specifications 9
Installation instructions 10-12
ClearancesInstallation into a masonry fire placeSealing
Gas connection 13-14
Fuel bed and log installation
Gas control 15-16
Gas pressure pointGas pressure sdjustment
Service instructions 17
GeneralTo replace the gas controlTo replace the fanTo replace the electronic controllerTo remove the burner and electrodesTo check pressures
Trouble shooting 18-19
ConnectionsElectric wiring diagramAuthorised service agents
2
Warranty
The Cannon appliance is warranted against defects in materials and workmanship for a period of one, (1) year from its date of original purchase, for residential use in Australia.
Warranty service, which includes parts and labour for the replace­ment or repair of defective parts, is available through Cannon Authorised Service Agencies. (Please refer to the list of authorised service agents in this manual.)
Consumers are responsible for service person’s travel outside nor­mal service areas (approximately seventy (70k) radius from the nearest Cannon dealer’s location), local cartage, and normal main­tenance as described in this manual.
Any product subjected to misuse, abuse, negligence, accident or alteration will have its warranty voided. The defacement of serial plate will have it’s warranty voided.
If installation is not carried out in accordance with manufacturer’s instructions, this warranty may be void.
The customer must keep their “Tax Invoice” as proof of purchase of this product and compliance certificate as proof of required instal­lation.
Model number: ______________________________________
Serial number: _______________________________________
Date of manufacture: _________________________________
Date installed: _______________________________________
Compliance Certificate No: ____________________________
Designed, manufactured and distributed by:
Sampford and Staff Pty Ltd. 421 Smith Street Fitzroy, Vic, 3065 Tel: (03) 9418 5888
Don’t risk your appliance warranty
Only a licensed person will give you a Compliance Certifi­cate, showing that the work complies with all the relevant standards.
And only a licensed person will have insurance protecting their workmanship for 6 years.
So make sure you use a licensed person to install this appli­ance and ask for your Compliance Certificate to ensure the manufacturers appliance warranty will be honoured.
3
Safety Warnings
Please read this manual before installing and using the heater.
What to do if you smell gas
Warnings
1. Turn OFF the main gas supply.
2. Extinguish any open flame.
3. Open windows.
4. Do not touch electrical switches.
5. Do not use your telephone.
6. Call your gas supplier immediately from a neighbour’s phone.
1. Improper installation, adjustment, alteration, service or main­tenance can cause injury or property damage. Refer to other sections of this manual for correct procedures, or consult with place of purchase, a licensed plumber, a gas supplier or service agent listed in this manual.
2. Due to high temperatures the room heater should be located out of traffic and away from:
Furniture and draperies,
Combustible materials,
Gasoline and other flammable liquids,
Do not place clothing or other flammable material on or near
the heater.
3. Keep curtains*, clothing, furniture and other flammable mate­rials at least 900mm from front and sides of the heater.
* At the owner’s discretion curtain clearance can be less than 900mm as long as they are restrained from the front, top and sides of the heater. The manufacturer takes no responsibility if curtain clearance is less than 900mm and not restrained.
4. Children and adults should be alerted to the hazard of high surface temperature and should take care to avoid burns or clothing ignition.
Young children should be carefully supervised when they are
in the same room as the heater.
5. Never attempt to burn paper or any other material in the heater.
6. Do not spray aerosols in the vicinity of this appliance while it is in operation.
7. If removed the glass window must be put back onto the unit prior to operating the heater.
8. Installation and repairs should be performed by a licensed service person only, refer to back of brochure for service number.
4
9. For installation into a non-combustible fireplace, ie: masonry or brick or into a mock fireplace, i.e. timber or plasterboard, the chimney and base should be of sound construction and be free from cracks and holes (to ensure that sufficient flue draught can be generated).
NOTE: WHEN INSTALLING INTO A MOCK FIREPLACE A
MOCK FIREPLACE HEATER MUST BE USED.
Mock fireplace model no’s: CANTIBM & CANTIBMLP.
10. The heater must be properly installed in a working chimney or connected to a venting system. Operation of this heater, when not connected into a working chimney or a properly installed and maintained venting system can result in carbon monoxide (CO) poisoning and possible death.
11. The appliance should be inspected prior to use, with regular inspections (annually) to be made by a licensed service per­son. It is important that circulating air passageways of the appliance be kept clean, dirt and lint free, for a safe and efficient operation of the heater.
12. On first lighting your heater a smell may occur due to it’s new condition. This is quite normal and will disappear after a few hours use at the maximum control position.
Important:
WHEN THIS HEATER IS OPERATING, THE GLASS FRONT IS HOT. A safety guard conforming to AGA requirements is available for this heater. It is an optional extra, which may be fitted to the heater to reduce the risk of fire or injury from burns. Its fitting is recom­mended when there are children present. For permanent protection of young children or the infirm, an optional mesh guard is recom­mended. Call your retailer or authorised service agent for further details.
Standards
This appliance meets the following standards:
Standards Australia: AS 3100 AS 5601/AG 601 AS 4553/AG 103
5
User instructions
Operating instructions
1. Plug the power cord into the wall socket and turn on the power
to the heater, see figure 1. Refrain from using an extension cord.
1
2. For control lay-out refer to figure 2
2
3. To turn heater on press switch to POWER ON position. There
is a 5 second delay before the burner ignites. At this setting the burner is on LOW and the fan speed is on LOW. Refer figure 3.
The burner will ignite on both HIGH and LOW settings.
3
4. To turn burner to HIGH setting, press switch for HIGH setting.
Refer figure 4.
.
4
6
Loading...
+ 14 hidden pages